Remove obsolete NDRPDR checks

Change-Id: If495493f4dce8d2eecfb8c06bcd587f315b70b1d
Signed-off-by: Peter Mikus <pmikus@cisco.com>

1 files changed, 0 insertions, 201 deletions

diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrchk.robot
deleted file mode 100644
index ebf642f9b5..0000000000
--- a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrchk.robot
+++ /dev/null
@@ -1,201 +0,0 @@
-# Copyright (c) 2017 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance/performance_setup.robot
-| ...
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK
-| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_20K
-| ...
-| Suite Setup | Set up 3-node performance topology with DUT's NIC model
-| ... | L3 | Intel-X520-DA2
-| Suite Teardown | Tear down 3-node performance topology
-| ...
-| Test Setup | Set up performance test
-| Test Teardown | Tear down performance ndrchk test
-| ...
-| Documentation | *Reference NDR throughput IPv6 routing verify test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6
-| ... | routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested
-| ... | with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* In short performance tests, TG verifies
-| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet
-| ... | loss tolerance. Ref-NDR value is periodically updated acording to
-| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long
-| ... | performance tests for the same DUT confiiguration. Test packets are
-| ... | generated by TG on links to DUTs. TG traffic profile contains two L3
-| ... | flow-groups (flow-group per direction, 10k flows per flow-group) with
-| ... | all packets containing Ethernet header, IPv6 header and static
-| ... | payload. Incrementing of IP.dst (IPv6 destination address) field is
-| ... | applied to both streams.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Variables ***
-| ${rts_per_flow}= | ${10000}
-# Traffic profile:
-| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow}
-
-*** Test Cases ***
-| tc01-78B-1t1c-ethip6-ip6scale20k-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte
-| | ... | frames using single trial throughput test at 2x 2.9mpps.
-| | [Tags] | 78B | 1T1C | STHREAD
-| | ${framesize}= | Set Variable | ${78}
-| | ${rate}= | Set Variable | 2.9mpps
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc02-1518B-1t1c-ethip6-ip6scale20k-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
-| | ... | frames using single trial throughput test at 2x 812743pps.
-| | [Tags] | 1518B | 1T1C | STHREAD
-| | ${framesize}= | Set Variable | ${1518}
-| | ${rate}= | Set Variable | 812743pps
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc03-9000B-1t1c-ethip6-ip6scale20k-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
-| | ... | frames using single trial throughput test at 2x 138580pps.
-| | [Tags] | 9000B | 1T1C | STHREAD
-| | ${framesize}= | Set Variable | ${9000}
-| | ${rate}= | Set Variable | 138580pps
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc04-78B-2t2c-ethip6-ip6scale20k-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte
-| | ... | frames using single trial throughput test at 2x 7.0mpps.
-| | [Tags] | 78B | 2T2C | MTHREAD
-| | ${framesize}= | Set Variable | ${78}
-| | ${rate}= | Set Variable | 7.0mpps
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc05-1518B-2t2c-ethip6-ip6scale20k-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
-| | ... | frames using single trial throughput test at 2x 812743pps.
-| | [Tags] | 1518B | 2T2C | MTHREAD
-| | ${framesize}= | Set Variable | ${1518}
-| | ${rate}= | Set Variable | 812743pps
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc06-9000B-2t2c-ethip6-ip6scale20k-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
-| | ... | frames using single trial throughput test at 2x 138580pps.
-| | [Tags] | 9000B | 2T2C | MTHREAD
-| | ${framesize}= | Set Variable | ${9000}
-| | ${rate}= | Set Variable | 138580pps
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc07-78B-4t4c-ethip6-ip6scale20k-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
-| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte
-| | ... | frames using single trial throughput test at 2x 9.6mpps.
-| | [Tags] | 78B | 4T4C | MTHREAD
-| | ${framesize}= | Set Variable | ${78}
-| | ${rate}= | Set Variable | 10.0mpps
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc08-1518B-4t4c-ethip6-ip6scale20k-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
-| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
-| | ... | frames using single trial throughput test at 2x 812743pps.
-| | [Tags] | 1518B | 4T4C | MTHREAD
-| | ${framesize}= | Set Variable | ${1518}
-| | ${rate}= | Set Variable | 812743pps
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc09-9000B-4t4c-ethip6-ip6scale20k-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
-| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
-| | ... | frames using single trial throughput test at 2x 138580pps.
-| | [Tags] | 9000B | 4T4C | MTHREAD
-| | ${framesize}= | Set Variable | ${9000}
-| | ${rate}= | Set Variable | 138580pps
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}