CSIT-687: Directory structure reorganization

Change-Id: I772c9e214be2461adf58124998d272e7d795220f
Signed-off-by: Tibor Frank <tifrank@cisco.com>
Signed-off-by: Maciek Konstantynowicz <mkonstan@cisco.com>

1 files changed, 201 insertions, 0 deletions

diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrchk.robot
new file mode 100644
index 0000000000..ebf642f9b5
--- /dev/null
+++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrchk.robot
@@ -0,0 +1,201 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK
+| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_20K
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| Test Teardown | Tear down performance ndrchk test
+| ...
+| Documentation | *Reference NDR throughput IPv6 routing verify test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6
+| ... | routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In short performance tests, TG verifies
+| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet
+| ... | loss tolerance. Ref-NDR value is periodically updated acording to
+| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long
+| ... | performance tests for the same DUT confiiguration. Test packets are
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3
+| ... | flow-groups (flow-group per direction, 10k flows per flow-group) with
+| ... | all packets containing Ethernet header, IPv6 header and static
+| ... | payload. Incrementing of IP.dst (IPv6 destination address) field is
+| ... | applied to both streams.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${rts_per_flow}= | ${10000}
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow}
+
+*** Test Cases ***
+| tc01-78B-1t1c-ethip6-ip6scale20k-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte
+| | ... | frames using single trial throughput test at 2x 2.9mpps.
+| | [Tags] | 78B | 1T1C | STHREAD
+| | ${framesize}= | Set Variable | ${78}
+| | ${rate}= | Set Variable | 2.9mpps
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc02-1518B-1t1c-ethip6-ip6scale20k-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
+| | ... | frames using single trial throughput test at 2x 812743pps.
+| | [Tags] | 1518B | 1T1C | STHREAD
+| | ${framesize}= | Set Variable | ${1518}
+| | ${rate}= | Set Variable | 812743pps
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc03-9000B-1t1c-ethip6-ip6scale20k-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
+| | ... | frames using single trial throughput test at 2x 138580pps.
+| | [Tags] | 9000B | 1T1C | STHREAD
+| | ${framesize}= | Set Variable | ${9000}
+| | ${rate}= | Set Variable | 138580pps
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc04-78B-2t2c-ethip6-ip6scale20k-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte
+| | ... | frames using single trial throughput test at 2x 7.0mpps.
+| | [Tags] | 78B | 2T2C | MTHREAD
+| | ${framesize}= | Set Variable | ${78}
+| | ${rate}= | Set Variable | 7.0mpps
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc05-1518B-2t2c-ethip6-ip6scale20k-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
+| | ... | frames using single trial throughput test at 2x 812743pps.
+| | [Tags] | 1518B | 2T2C | MTHREAD
+| | ${framesize}= | Set Variable | ${1518}
+| | ${rate}= | Set Variable | 812743pps
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc06-9000B-2t2c-ethip6-ip6scale20k-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
+| | ... | frames using single trial throughput test at 2x 138580pps.
+| | [Tags] | 9000B | 2T2C | MTHREAD
+| | ${framesize}= | Set Variable | ${9000}
+| | ${rate}= | Set Variable | 138580pps
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc07-78B-4t4c-ethip6-ip6scale20k-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte
+| | ... | frames using single trial throughput test at 2x 9.6mpps.
+| | [Tags] | 78B | 4T4C | MTHREAD
+| | ${framesize}= | Set Variable | ${78}
+| | ${rate}= | Set Variable | 10.0mpps
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc08-1518B-4t4c-ethip6-ip6scale20k-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
+| | ... | frames using single trial throughput test at 2x 812743pps.
+| | [Tags] | 1518B | 4T4C | MTHREAD
+| | ${framesize}= | Set Variable | ${1518}
+| | ${rate}= | Set Variable | 812743pps
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc09-9000B-4t4c-ethip6-ip6scale20k-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
+| | ... | frames using single trial throughput test at 2x 138580pps.
+| | [Tags] | 9000B | 4T4C | MTHREAD
+| | ${framesize}= | Set Variable | ${9000}
+| | ${rate}= | Set Variable | 138580pps
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}