diff options
Diffstat (limited to 'tests/perf/Long_Lisp_Intel-X520-DA2.robot')
| -rw-r--r-- | tests/perf/Long_Lisp_Intel-X520-DA2.robot | 2328 |
1 files changed, 2328 insertions, 0 deletions
diff --git a/tests/perf/Long_Lisp_Intel-X520-DA2.robot b/tests/perf/Long_Lisp_Intel-X520-DA2.robot new file mode 100644 index 0000000000..2ff8a582ab --- /dev/null +++ b/tests/perf/Long_Lisp_Intel-X520-DA2.robot @@ -0,0 +1,2328 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance.robot +| Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot +| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']} +| ... | WITH NAME | dut1_v4 +| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']} +| ... | WITH NAME | dut2_v4 +# import additional Lisp settings from resource file +| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_LONG +| ... | NIC_Intel-X520-DA2 +| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | 3-node Performance Suite Teardown +| Test Setup | Setup all DUTs before test +| Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs +| Documentation | *RFC6830: Pkt throughput Lisp test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, +| ... | Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel; +| ... | Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for +| ... | IPv6 routing over LISPoIPv6 tunnel; Eth-IPv6-LISP-IPv4-ICMPv4 on +| ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 +| ... | tunnel; Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on +| ... | TG-DUTn for IPv6 routing over LISPoIPv4 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 (IPv6) +| ... | routing and static routes. LISPoIPv4 (oIPv6) tunnel is configured +| ... | between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic +| ... | by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Test Cases *** +| TC01: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC02: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4 +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC03: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1480 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1480 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC04: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. [Ver] Find PDR for 1480 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4 +| | ${framesize}= | Set Variable | 1480 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC05: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC06: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4 +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC07: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC08: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4 +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC09: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1480 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1480 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC10: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1480 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1480 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC11: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC12: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC13: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC14: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4 +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC15: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1480 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1480 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC16: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1480 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1480 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC17: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC18: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC19: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC20: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC21: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC22: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC23: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC24: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC25: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC26: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC27: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC28: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC29: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC30: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC31: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC32: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC33: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC34: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC35: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC36: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC37: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC38: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4oIPv6 +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC39: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC40: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4oIPv6 +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC41: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC42: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4oIPv6 +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC43: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC44: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC45: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC46: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC47: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC48: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC49: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC50: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC51: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC52: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1460 Byte frames using binary search starlt +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC53: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC54: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv4 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC55: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC56: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6IPv4 +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC57: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC58: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6oIPv4 +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC59: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC60: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6oIPv4 +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC61: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC62: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC63: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC64: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC65: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC66: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC67: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC68: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 78 Byte frames using binary search start +| | ... | at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 +| | ${framesize}= | Set Variable | 78 +| | ${min_rate}= | Set Variable | 100000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC69: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC70: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start +| | ... | at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 1460 +| | ${min_rate}= | Set Variable | 10000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} + +| TC71: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} + +| TC72: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC +| | ... | port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start +| | ... | at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 | SKIP_PATCH +| | ${framesize}= | Set Variable | 9000 +| | ${min_rate}= | Set Variable | 5000 +| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | 3-node-IPv6 +| | ... | ${min_rate} | ${max_rate} +| | ... | ${threshold} +| | ... | ${glob_loss_acceptance} +| | ... | ${glob_loss_acceptance_type} |