From e2f3f7663bd9bda3b41c877495a2601c9839abd1 Mon Sep 17 00:00:00 2001 From: Maciek Konstantynowicz Date: Fri, 17 Jun 2016 19:57:41 +0100 Subject: Suite: performance. Updated test cases names and test cases documentation. Change-Id: I37dd1e9843c11a37d27565be110620e179c1232c Signed-off-by: pmikus --- .../Short_Bridge_Domain_Intel-X520-DA2.robot | 82 +++++++++++------ .../Short_IPv6_Cop_Intel-X520-DA2.robot | 83 +++++++++++------ .../performance/Short_IPv6_Intel-X520-DA2.robot | 82 +++++++++++------ .../Short_Xconnect_Dot1q_Intel-X520-DA2.robot | 100 +++++++++++---------- .../Short_Xconnect_Intel-X520-DA2.robot | 82 +++++++++++------ 5 files changed, 271 insertions(+), 158 deletions(-) (limited to 'tests/suites') diff --git a/tests/suites/performance/Short_Bridge_Domain_Intel-X520-DA2.robot b/tests/suites/performance/Short_Bridge_Domain_Intel-X520-DA2.robot index 1e8d6669c5..b0aec9ba16 100644 --- a/tests/suites/performance/Short_Bridge_Domain_Intel-X520-DA2.robot +++ b/tests/suites/performance/Short_Bridge_Domain_Intel-X520-DA2.robot @@ -21,13 +21,31 @@ | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test | Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs -| Documentation | Minimal throughput acceptance test cases +| Documentation | *Reference NDR throughput L2BD verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC +| ... | X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and generated payload. +| ... | *[Ref] Applicable standard specifications:* RFC2544. *** Test Cases *** -| 1core VPP passes 64B frames through bridge domain at 2x 3.2Mpps in 3-node topology +| TC01: Verify 64B ref-NDR at 2x 3.2Mpps - DUT L2BD - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 64B frames through bridge domain -| | ... | at 2x 3.2Mpps in 3-node topology. +| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 @@ -40,10 +58,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-bridge -| 1core VPP passes 1518B frames through bridge domain at 2x 812,743pps in 3-node topology +| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT L2BD - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 1518B frames through bridge domain -| | ... | at 2x 812,743pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -56,10 +75,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-bridge -| 1core VPP passes 9000B frames through bridge domain at 2x 138,580pps in 3-node topology +| TC03: Verify 9000B ref-NDR at 2x 138.58kpps - DUT L2BD - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 9000B frames through bridge domain -| | ... | at 2x 138,580pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -71,10 +91,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-bridge -| 2core VPP with rxqueues 1 passes 64B frames through bridge domain at 2x 6.9Mpps in 3-node topology +| TC04: Verify 64B ref-NDR at 2x 6.9Mpps - DUT L2BD - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 64B frames through bridge domain -| | ... | at 2x 6.9Mpps in 3-node topology. +| | ... | [Cfg] DUT runs L2BD config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 @@ -87,10 +108,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-bridge -| 2core VPP with rxqueues 1 passes 1518B frames through bridge domain at 2x 812,743pps in 3-node topology +| TC05: Verify 1518B ref-NDR at 2x 812.74kpps - DUT L2BD - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 1518B frames through bridge domain -| | ... | at 2x 812,743pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2BD config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -103,10 +125,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-bridge -| 2core VPP with rxqueues 1 passes 9000B frames through bridge domain at 2x 138,580pps in 3-node topology +| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT L2BD - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 9000B frames through bridge domain -| | ... | at 2x 138,580pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2BD config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -118,10 +141,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-bridge -| 4core VPP with rxqueues 2 passes 64B frames through bridge domain at 2x 7.4Mpps in 3-node topology +| TC07: Verify 64B ref-NDR at 2x 7.4Mpps - DUT L2BD - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 64B frames through bridge -| | ... | domain at 2x7.4Mpps in 3-node topology. +| | ... | [Cfg] DUT runs L2BD config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 @@ -134,10 +158,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-bridge -| 4core VPP with rxqueues 2 passes 1518B frames through bridge domain at 2x 812,743pps in 3-node topology +| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT L2BD - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 1518B frames through bridge -| | ... | domain at 2x 812,743pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2BD config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -150,10 +175,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-bridge -| 4core VPP with rxqueues 2 passes 9000B frames through bridge domain at 2x 138,580pps in 3-node topology +| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT L2BD - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2should pass 9000B frames through bridge -| | ... | domain at 2x 138,580pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2BD config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 diff --git a/tests/suites/performance/Short_IPv6_Cop_Intel-X520-DA2.robot b/tests/suites/performance/Short_IPv6_Cop_Intel-X520-DA2.robot index 81ffdd8f0b..17addec047 100644 --- a/tests/suites/performance/Short_IPv6_Cop_Intel-X520-DA2.robot +++ b/tests/suites/performance/Short_IPv6_Cop_Intel-X520-DA2.robot @@ -21,13 +21,32 @@ | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test | Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs -| Documentation | Minimal throughput acceptance test cases +| Documentation | *Reference NDR throughput IPv6 whitelist verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing, two static IPv6 /64 routes and IPv6 COP security whitelist +| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and generated +| ... | payload. +| ... | *[Ref] Applicable standard specifications:* RFC2544. *** Test Cases *** -| 1core VPP passes 78B frames through IPv6 forwarding with COP at 2x 2.8Mpps in 3-node topology +| TC01: Verify 78B ref-NDR at 2x 2.8Mpps - DUT IPv6 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 78B frames through IPv6 forwarding -| | ... | at 2x 2.8Mpps in 3-node topology with COP. +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 78 Byte frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 @@ -46,10 +65,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 1core VPP passes 1518B frames through IPv6 forwarding with COP at 2x 812,743pps in 3-node topology +| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 1518B frames through IPv6 forwarding -| | ... | at 2x 812,743pps (2x 10Gbps) in 3-node topology with COP. +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 1518 Byte frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -68,10 +88,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 1core VPP passes 9000B frames through IPv6 forwarding with COP at 2x 138,580pps in 3-node topology +| TC03: Verify 9000B ref-NDR at 2x 138.580kpps - DUT IPv6 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 9000B frames through IPv6 forwarding -| | ... | at 2x138,580pps (2x 10Gbps) in 3-node topology with COP. +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 9000 Byte frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -89,10 +110,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 2core VPP with rxqueues 1 passes 78B frames through IPv6 forwarding with COP at 2x 4.9Mpps in 3-node topology +| TC04: Verify 78B ref-NDR at 2x 4.9Mpps - DUT IPv6 whitelist - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 78B frames through IPv6 forwarding -| | ... | at 2x 4.9Mpps in 3-node topology with COP. +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 78 Byte frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 @@ -111,10 +133,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 2core VPP with rxqueues 1 passes 1518B frames through IPv6 forwarding with COP at 2x 812,743pps in 3-node topology +| TC05: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 whitelist - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 1518B frames through IPv6 forwarding -| | ... | at 2x 812,743pps (2x 10Gbps) in 3-node topology with COP. +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 1518 Byte frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -133,10 +156,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 2core VPP with rxqueues 1 passes 9000B frames through IPv6 forwarding with COP at 2x 138,580pps in 3-node topology +| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 whitelist - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 9000B frames through IPv6 forwarding -| | ... | at 2x 138,580pps (2x 10Gbps) in 3-node topology with COP. +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 9000 Byte frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -154,10 +178,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 4core VPP with rxqueues 2 passes 78B frames through IPv6 forwarding with COP at 2x 10.1Mpps in 3-node topology +| TC07: Verify 78B ref-NDR at 2x 10.1Mpps - DUT IPv6 whitelist - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 78B frames through IPv6 -| | ... | forwarding at 2x 10.1Mpps in 3-node topology with COP. +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 78 Byte frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 @@ -176,10 +201,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 4core VPP with rxqueues 2 passes 1518B frames through IPv6 forwarding with COP at 2x 812,743pps in 3-node topology +| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 whitelist - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 1518B frames through IPv6 -| | ... | forwarding at 2x 812,743pps (2x 10Gbps) in 3-node topology with COP. +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 1518 Byte frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -198,10 +224,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 4core VPP with rxqueues 2 passes 9000B frames through IPv6 forwarding with COP at 2x 138,580pps in 3-node topology +| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 whitelist - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 9000B frames through IPv6 -| | ... | forwarding at 2x 138,580pps (2x 10Gbps) in 3-node topology with COP. +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 9000 Byte frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 diff --git a/tests/suites/performance/Short_IPv6_Intel-X520-DA2.robot b/tests/suites/performance/Short_IPv6_Intel-X520-DA2.robot index c5858455b1..4b79a3495d 100644 --- a/tests/suites/performance/Short_IPv6_Intel-X520-DA2.robot +++ b/tests/suites/performance/Short_IPv6_Intel-X520-DA2.robot @@ -21,13 +21,31 @@ | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test | Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs -| Documentation | Minimal throughput acceptance test cases +| Documentation | *Reference NDR throughput IPv6 routing verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with +| ... | 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and generated +| ... | payload. +| ... | *[Ref] Applicable standard specifications:* RFC2544. *** Test Cases *** -| 1core VPP passes 78B frames through IPv6 forwarding at 2x 2.9Mpps in 3-node topology +| TC01: Verify 78B ref-NDR at 2x 2.9Mpps - DUT IPv6 - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 78B frames through IPv6 forwarding -| | ... | at 2x2.9Mpps in 3-node topology. +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 @@ -40,10 +58,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 1core VPP passes 1518B frames through IPv6 forwarding at 2x 812,743pps in 3-node topology +| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 1518B frames through IPv6 forwarding -| | ... | at 2x812,743pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -56,10 +75,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 1core VPP passes 9000B frames through IPv6 forwarding at 2x 138,580pps in 3-node topology +| TC03: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 9000B frames through IPv6 forwarding -| | ... | at 2x138,580pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -71,10 +91,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 2core VPP with rxqueues 1 passes 78B frames through IPv6 forwarding at 2x 5.9Mpps in 3-node topology +| TC04: Verify 78B ref-NDR at 2x 5.9Mpps - DUT IPv6 - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 78B frames through IPv6 forwarding -| | ... | at 2x5.9Mpps in 3-node topology. +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 @@ -87,10 +108,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 2core VPP with rxqueues 1 passes 1518B frames through IPv6 forwarding at 2x 812,743pps in 3-node topology +| TC05: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 1518B frames through IPv6 forwarding -| | ... | at 2x812,743pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -103,10 +125,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 2core VPP with rxqueues 1 passes 9000B frames through IPv6 forwarding at 2x 138,580pps in 3-node topology +| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 9000B frames through IPv6 forwarding -| | ... | at 2x138,580pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -118,10 +141,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 4core VPP with rxqueues 2 passes 78B frames through IPv6 forwarding at 2x 7.3Mpps in 3-node topology +| TC07: Verify 78B ref-NDR at 2x 7.3Mpps - DUT IPv6 - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 78B frames through IPv6 -| | ... | forwarding at 2x7.3Mpps in 3-node topology. +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 @@ -134,10 +158,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 4core VPP with rxqueues 2 passes 1518B frames through IPv6 forwarding at 2x 812,743pps in 3-node topology +| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 1518B frames through IPv6 -| | ... | forwarding at 2x812,743pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -150,10 +175,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 -| 4core VPP with rxqueues 2 passes 9000B frames through IPv6 forwarding at 2x 138,580pps in 3-node topology +| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 9000B frames through IPv6 -| | ... | forwarding at 2x138,580pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 diff --git a/tests/suites/performance/Short_Xconnect_Dot1q_Intel-X520-DA2.robot b/tests/suites/performance/Short_Xconnect_Dot1q_Intel-X520-DA2.robot index 576a66f74c..864962daa0 100644 --- a/tests/suites/performance/Short_Xconnect_Dot1q_Intel-X520-DA2.robot +++ b/tests/suites/performance/Short_Xconnect_Dot1q_Intel-X520-DA2.robot @@ -21,19 +21,35 @@ | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test | Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs -| Documentation | Minimal throughput acceptance test cases +| Documentation | *Reference NDR throughput L2XC verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. Dot1q +| ... | tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and generated payload. +| ... | *[Ref] Applicable standard specifications:* RFC2544. *** Variables *** | ${subid}= | 10 | ${tag_rewrite}= | pop-1 *** Test Cases *** -| 1core VPP passes 64B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect at 2x2.9Mpps in 3-node topology +| TC01: Verify 64B ref-NDR at 2x 2.9Mpps - DUT dot1q - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 64B frames through VLAN dot1q -| | ... | sub-interfaces inter-connected using L2 cross connect at 2x2.9Mpps in -| | ... | 3-node topology. Tagging is applied between DUTs inserting 4B VLAN ID -| | ... | into a packet header. +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 @@ -54,12 +70,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 1core VPP passes 1518B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect at 2x 720,000pps in 3-node topology +| TC02: Verify 1518B ref-NDR at 2x 720kpps - DUT dot1q - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 1518B frames through VLAN dot1q -| | ... | sub-interfaces inter-connected using L2 cross connect at -| | ... | 2x 720,000pps in 3-node topology. Tagging is applied between DUTs -| | ... | inserting 4B VLAN ID into a packet header. +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -80,12 +95,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 1core VPP passes 9000B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect at 2x 120,000pps in 3-node topology +| TC03: Verify 9000B ref-NDR at 2x 120kpps - DUT dot1q - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 9000B frames through VLAN dot1q -| | ... | sub-interfaces inter-connected using L2 cross connect at -| | ... | 2x 120,000pps in 3-node topology. Tagging is applied between DUTs -| | ... | inserting 4B VLAN ID into a packet header. +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -105,12 +119,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 2core VPP with rxqueues 1 passes 64B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect at 2x7.0Mpps in 3-node topology +| TC04: Verify 64B ref-NDR at 2x 7Mpps - DUT dot1q - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 64B frames through VLAN dot1q -| | ... | sub-interfaces inter-connected using L2 cross connect at 2x7.0Mpps in -| | ... | 3-node topology. Tagging is applied between DUTs inserting 4B VLAN ID -| | ... | into a packet header. +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 @@ -131,12 +144,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 2core VPP with rxqueues 1 passes 1518B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect at 2x 720,000pps in 3-node topology +| TC05: Verify 1518B ref-NDR at 2x 720kpps - DUT dot1q - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 core should pass 1518B frames through VLAN dot1q -| | ... | sub-interfaces inter-connected using L2 cross connect at -| | ... | 2x 720,000pps in 3-node topology. Tagging is applied between DUTs -| | ... | inserting 4B VLAN ID into a packet header. +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -157,12 +169,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 2core VPP with rxqueues 1 passes 9000B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect at 2x 120,000pps in 3-node topology +| TC06: Verify 9000B ref-NDR at 2x 120kpps - DUT dot1q - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 core should pass 9000B frames through VLAN dot1q -| | ... | sub-interfaces inter-connected using L2 cross connect at -| | ... | 2x 120,000pps in 3-node topology. Tagging is applied between DUTs -| | ... | inserting 4B VLAN ID into a packet header. +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -182,12 +193,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 4core VPP with rxqueues 2 passes 64B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect at 2x11Mpps in 3-node topology +| TC07: Verify 64B ref-NDR at 2x 11Mpps - DUT dot1q - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 64B frames through VLAN dot1q -| | ... | sub-interfaces inter-connected using L2 cross connect at 2x11Mpps in -| | ... | 3-node topology. Tagging is applied between DUTs inserting 4B VLAN ID -| | ... | into a packet header. +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 @@ -208,12 +218,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 4core VPP with rxqueues 2 passes 1518B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect at 2x 720,000pps in 3-node topology +| TC08: Verify 1518B ref-NDR at 2x 720kpps - DUT dot1q - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 1518B frames through VLAN -| | ... | dot1q sub-interfaces inter-connected using L2 cross connect at -| | ... | 2x 720,000pps in 3-node topology. Tagging is applied between DUTs -| | ... | inserting 4B VLAN ID into a packet header. +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -234,12 +243,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 4core VPP with rxqueues 2 passes 9000B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect at 2x 120,000pps in 3-node topology +| TC09: Verify 9000B ref-NDR at 2x 120kpps - DUT dot1q - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 9000B frames through VLAN -| | ... | dot1q sub-interfaces inter-connected using L2 cross connect at -| | ... | 2x 120,000pps in 3-node topology. Tagging is applied between DUTs -| | ... | inserting 4B VLAN ID into a packet header. +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 diff --git a/tests/suites/performance/Short_Xconnect_Intel-X520-DA2.robot b/tests/suites/performance/Short_Xconnect_Intel-X520-DA2.robot index 6d46768ee2..44a31f753f 100644 --- a/tests/suites/performance/Short_Xconnect_Intel-X520-DA2.robot +++ b/tests/suites/performance/Short_Xconnect_Intel-X520-DA2.robot @@ -22,13 +22,31 @@ | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test | Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs -| Documentation | Minimal throughput acceptance test cases +| Documentation | *Reference NDR throughput L2XC verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 +| ... | routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with +| ... | 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and generated payload. +| ... | *[Ref] Applicable standard specifications:* RFC2544. *** Test Cases *** -| 1core VPP passes 64B frames through L2 cross connect at 2x 3.6Mpps in 3-node topology +| TC01: Verify 64B ref-NDR at 2x 3.6Mpps - DUT L2XC - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 64B frames through L2 cross connect -| | ... | at 2x3.6Mpps in 3-node topology. +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 @@ -41,10 +59,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 1core VPP passes 1518B frames through L2 cross connect at 2x 812,743pps in 3-node topology +| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT L2XC - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 1518B frames through L2 cross connect -| | ... | at 2x 812,743pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -57,10 +76,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 1core VPP passes 9000B frames through L2 cross connect at 2x 138,580pps in 3-node topology +| TC03: Verify 9000B ref-NDR at 2x 138.58kpps - DUT L2XC - 1thread 1core 1rxq | | [Documentation] -| | ... | VPP with 1 core should pass 9000B frames through L2 cross connect -| | ... | at 2x 138,580pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -72,10 +92,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 2core VPP with rxqueues 1 passes 64B frames through L2 cross connect at 2x 8.3Mpps in 3-node topology +| TC04: Verify 64B ref-NDR at 2x 8.3Mpps - DUT L2XC - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 64B frames through L2 cross connect -| | ... | at 2x 8.3Mpps in 3-node topology. +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 @@ -88,10 +109,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 2core VPP with rxqueues 1 passes 1518B frames through L2 cross connect at 2x 812,743pps in 3-node topology +| TC05: Verify 1518B ref-NDR at 2x 812.43kpps - DUT L2XC - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 1518B frames through L2 cross connect -| | ... | at 2x 812,743pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -104,10 +126,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 2core VPP with rxqueues 1 passes 9000B frames through L2 cross connect at 2x 138,580pps in 3-node topology +| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT L2XC - 2thread 2core 1rxq | | [Documentation] -| | ... | VPP with 2 cores should pass 9000B frames through L2 cross connect -| | ... | at 2x 138,580pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 @@ -119,10 +142,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 4core VPP with rxqueues 2 passes 64B frames through L2 cross connect at 2x 9.3Mpps in 3-node topology +| TC07: Verify 64B ref-NDR at 2x 9.3Mpps - DUT L2XC - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 64B frames through L2 cross -| | ... | connect at 2x9.3Mpps in 3-node topology. +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 @@ -135,10 +159,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 4core VPP with rxqueues 2 passes 1518B frames through L2 cross connect at 2x 812,743pps in 3-node topology +| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT L2XC - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 1518B frames through L2 cross -| | ... | connect at 2x 812,743pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${duration}= | Set Variable | 10 @@ -151,10 +176,11 @@ | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-xconnect -| 4core VPP with rxqueues 2 passes 9000B frames through L2 cross connect at 2x 138,580pps in 3-node topology +| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT L2XC - 4thread 4core 2rxq | | [Documentation] -| | ... | VPP with 4 cores and rxqueues 2 should pass 9000B frames through L2 cross -| | ... | connect at 2x 138,580pps (2x 10Gbps) in 3-node topology. +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 -- cgit 1.2.3-korg