From 0ba508f0eac819c1985e825857f584b3d1537ffe Mon Sep 17 00:00:00 2001 From: Jan Gelety Date: Tue, 5 Dec 2017 14:27:26 +0100 Subject: CSIT-861: SW cryptodev perf tests Change-Id: I687216ca43569542d38be681ca04c898010fc65d Signed-off-by: Jan Gelety --- ...secbasetnl-ip4base-int-aes-gcm-ndrpdrdisc.robot | 243 +++++---------------- ...cbasetnlsw-ip4base-int-aes-gcm-ndrpdrdisc.robot | 212 ++++++++++++++++++ ...basetnlsw-ip4base-int-cbc-sha1-ndrpdrdisc.robot | 212 ++++++++++++++++++ ...cbasetnlsw-ip4base-tnl-aes-gcm-ndrpdrdisc.robot | 215 ++++++++++++++++++ ...basetnlsw-ip4base-tnl-cbc-sha1-ndrpdrdisc.robot | 215 ++++++++++++++++++ 5 files changed, 904 insertions(+), 193 deletions(-) create mode 100644 tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-ndrpdrdisc.robot create mode 100644 tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-ndrpdrdisc.robot create mode 100644 tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-ndrpdrdisc.robot create mode 100644 tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-ndrpdrdisc.robot (limited to 'tests/vpp') diff --git a/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-aes-gcm-ndrpdrdisc.robot b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-aes-gcm-ndrpdrdisc.robot index 934f260c74..5a2f10c014 100644 --- a/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-aes-gcm-ndrpdrdisc.robot +++ b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-aes-gcm-ndrpdrdisc.robot @@ -19,6 +19,7 @@ | ... | IP4FWD | IPSEC | IPSECHW | IPSECTUN | NIC_Intel-XL710 | BASE | ... | Suite Setup | Set up IPSec performance test suite | L3 | Intel-XL710 +| ... | HW_cryptodev | ... | Suite Teardown | Tear down 3-node performance topology | ... @@ -54,7 +55,7 @@ *** Variables *** # XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps -| ${s_24.5G} | ${24500000000} +| ${s_limit} | ${24500000000} # XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps | ${s_18.75Mpps} | ${18750000} | ${tg_if1_ip4}= | 192.168.10.2 @@ -71,40 +72,56 @@ # Traffic profile: | ${traffic_profile} | trex-sl-3n-ethip4-ip4dst${n_tunnels} -*** Test Cases *** -| tc01-64B-1t1c-ethip4ipsecbasetnl-ip4base-int-aes-gcm-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ -| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. -| | ... | [Ver] Find NDR for 64 Byte frames\ -| | ... | using binary search start at 40GE linerate, step 100kpps. -| | ... -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with IPSec HW cryptodev +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} +| | ... | ${get_framesize} + ${ipsec_overhead_gcm} +| | ${max_rate}= | Set Variable If +| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | ${encr_alg}= | Crypto Alg AES GCM 128 | | ${auth_alg}= | Integ Alg AES GCM 128 -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology | | And Add PCI devices to DUTs in 3-node single link topology | | And Add no multi seg to all DUTs -| | And Add cryptodev to all DUTs | ${1} +| | And Add cryptodev to all DUTs | ${${wt}} | | And Add DPDK dev default RXD to all DUTs | 2048 | | And Add DPDK dev default TXD to all DUTs | 2048 | | And Apply startup configuration on all VPP DUTs +| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} | | And Initialize IPSec in 3-node circular topology | | And VPP IPsec Create Tunnel Interfaces | | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} | | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} | | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} -| | Then Find NDR using binary search and pps | ${framesize} -| | ... | ${binary_min} | ${binary_max} | ${traffic_profile} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} | | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4ipsecbasetnl-ip4base-int-aes-gcm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec HW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR | tc02-64B-1t1c-ethip4ipsecbasetnl-ip4base-int-aes-gcm-pdrdisc | | [Documentation] @@ -115,31 +132,8 @@ | | ... | | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Set Variable | ${s_18.75Mpps} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | ${encr_alg}= | Crypto Alg AES GCM 128 -| | ${auth_alg}= | Integ Alg AES GCM 128 -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add cryptodev to all DUTs | ${1} -| | And Add DPDK dev default RXD to all DUTs | 2048 -| | And Add DPDK dev default TXD to all DUTs | 2048 -| | And Apply startup configuration on all VPP DUTs -| | And Initialize IPSec in 3-node circular topology -| | And VPP IPsec Create Tunnel Interfaces -| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} -| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} -| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} -| | Then Find PDR using binary search and pps | ${framesize} -| | ... | ${binary_min} | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec HW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR | tc03-1518B-1t1c-ethip4ipsecbasetnl-ip4base-int-aes-gcm-ndrdisc | | [Documentation] @@ -150,30 +144,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} -| | ... | ${framesize + ${ipsec_overhead_gcm}} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | ${encr_alg}= | Crypto Alg AES GCM 128 -| | ${auth_alg}= | Integ Alg AES GCM 128 -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add cryptodev to all DUTs | ${1} -| | And Add DPDK dev default RXD to all DUTs | 2048 -| | And Add DPDK dev default TXD to all DUTs | 2048 -| | And Apply startup configuration on all VPP DUTs -| | And Initialize IPSec in 3-node circular topology -| | And VPP IPsec Create Tunnel Interfaces -| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} -| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} -| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} -| | Then Find NDR using binary search and pps | ${framesize} -| | ... | ${binary_min} | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec HW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR | tc04-1518B-1t1c-ethip4ipsecbasetnl-ip4base-int-aes-gcm-pdrdisc | | [Documentation] @@ -184,31 +156,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} -| | ... | ${framesize + ${ipsec_overhead_gcm}} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | ${encr_alg}= | Crypto Alg AES GCM 128 -| | ${auth_alg}= | Integ Alg AES GCM 128 -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add cryptodev to all DUTs | ${1} -| | And Add DPDK dev default RXD to all DUTs | 2048 -| | And Add DPDK dev default TXD to all DUTs | 2048 -| | And Apply startup configuration on all VPP DUTs -| | And Initialize IPSec in 3-node circular topology -| | And VPP IPsec Create Tunnel Interfaces -| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} -| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} -| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} -| | Then Find PDR using binary search and pps | ${framesize} -| | ... | ${binary_min} | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec HW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR | tc05-IMIX-1t1c-ethip4ipsecbasetnl-ip4base-int-aes-gcm-ndrdisc | | [Documentation] @@ -220,31 +169,8 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${imix_size}= | Get Frame Size | ${framesize} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} -| | ... | ${imix_size} + ${ipsec_overhead_gcm} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | ${encr_alg}= | Crypto Alg AES GCM 128 -| | ${auth_alg}= | Integ Alg AES GCM 128 -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add cryptodev to all DUTs | ${1} -| | And Add DPDK dev default RXD to all DUTs | 2048 -| | And Add DPDK dev default TXD to all DUTs | 2048 -| | And Apply startup configuration on all VPP DUTs -| | And Initialize IPSec in 3-node circular topology -| | And VPP IPsec Create Tunnel Interfaces -| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} -| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} -| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} -| | Then Find NDR using binary search and pps | ${framesize} -| | ... | ${binary_min} | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec HW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR | tc06-IMIX-1t1c-ethip4ipsecbasetnl-ip4base-int-aes-gcm-pdrdisc | | [Documentation] @@ -256,32 +182,8 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${imix_size}= | Get Frame Size | ${framesize} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} -| | ... | ${imix_size} + ${ipsec_overhead_gcm} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | ${encr_alg}= | Crypto Alg AES GCM 128 -| | ${auth_alg}= | Integ Alg AES GCM 128 -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add cryptodev to all DUTs | ${1} -| | And Add DPDK dev default RXD to all DUTs | 2048 -| | And Add DPDK dev default TXD to all DUTs | 2048 -| | And Apply startup configuration on all VPP DUTs -| | And Initialize IPSec in 3-node circular topology -| | And VPP IPsec Create Tunnel Interfaces -| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} -| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} -| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} -| | Then Find PDR using binary search and pps | ${framesize} -| | ... | ${binary_min} | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec HW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR | tc07-64B-2t2c-ethip4ipsecbasetnl-ip4base-int-aes-gcm-ndrdisc | | [Documentation] @@ -292,30 +194,8 @@ | | ... | | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Set Variable | ${s_18.75Mpps} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | ${encr_alg}= | Crypto Alg AES GCM 128 -| | ${auth_alg}= | Integ Alg AES GCM 128 -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add cryptodev to all DUTs | ${2} -| | And Add DPDK dev default RXD to all DUTs | 2048 -| | And Add DPDK dev default TXD to all DUTs | 2048 -| | And Apply startup configuration on all VPP DUTs -| | And Initialize IPSec in 3-node circular topology -| | And VPP IPsec Create Tunnel Interfaces -| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} -| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} -| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} -| | Then Find NDR using binary search and pps | ${framesize} -| | ... | ${binary_min} | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec HW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR | tc08-64B-2t2c-ethip4ipsecbasetnl-ip4base-int-aes-gcm-pdrdisc | | [Documentation] @@ -326,28 +206,5 @@ | | ... | | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Set Variable | ${s_18.75Mpps} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | ${encr_alg}= | Crypto Alg AES GCM 128 -| | ${auth_alg}= | Integ Alg AES GCM 128 -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add cryptodev to all DUTs | ${2} -| | And Add DPDK dev default RXD to all DUTs | 2048 -| | And Add DPDK dev default TXD to all DUTs | 2048 -| | And Apply startup configuration on all VPP DUTs -| | And Initialize IPSec in 3-node circular topology -| | And VPP IPsec Create Tunnel Interfaces -| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} -| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} -| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} -| | Then Find PDR using binary search and pps | ${framesize} -| | ... | ${binary_min} | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec HW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-ndrpdrdisc.robot b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-ndrpdrdisc.robot new file mode 100644 index 0000000000..b30bd5bf83 --- /dev/null +++ b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-ndrpdrdisc.robot @@ -0,0 +1,212 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/crypto/ipsec.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | IP4FWD | IPSEC | IPSECSW | IPSECTUN | NIC_Intel-XL710 | BASE +| ... +| Suite Setup | Set up IPSec performance test suite | L3 | Intel-XL710 +| ... | SW_cryptodev +| ... +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *IPv4 IPsec tunnel mode performance test suite.* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 on TG-DUTn, +| ... | Eth-IPv4-IPSec on DUT1-DUT2 +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with DPDK SW +| ... | crypto devices and multiple IPsec tunnels between them. DUTs get IPv4 +| ... | traffic from TG, encrypt it and send to another DUT, where packets are +| ... | decrypted and sent back to TG. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in number +| ... | of packets transmitted. NDR is discovered for different +| ... | number of IPsec tunnels using binary search algorithms with configured +| ... | starting rate and final step that determines throughput measurement +| ... | resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, number of flows per flow-group equals to +| ... | number of IPSec tunnels) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and +| ... | static payload. MAC addresses are matching MAC addresses of the TG +| ... | node interfaces. Incrementing of IP.dst (IPv4 destination address) field +| ... | is applied to both streams. +| ... | *[Ref] Applicable standard specifications:* RFC4303 and RFC2544. + +*** Variables *** +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_limit} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +| ${tg_if1_ip4}= | 192.168.10.2 +| ${dut1_if1_ip4}= | 192.168.10.1 +| ${dut1_if2_ip4}= | 172.168.1.1 +| ${dut2_if1_ip4}= | 172.168.1.2 +| ${dut2_if2_ip4}= | 192.168.20.1 +| ${tg_if2_ip4}= | 192.168.20.2 +| ${raddr_ip4}= | 20.0.0.0 +| ${laddr_ip4}= | 10.0.0.0 +| ${addr_range}= | ${32} +| ${ipsec_overhead_gcm}= | ${54} +| ${n_tunnels}= | ${1} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4dst${n_tunnels} + +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} +| | ... | ${get_framesize} + ${ipsec_overhead_gcm} +| | ${max_rate}= | Set Variable If +| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | ${encr_alg}= | Crypto Alg AES GCM 128 +| | ${auth_alg}= | Integ Alg AES GCM 128 +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Add DPDK SW cryptodev on DUTs in 3-node single-link circular topology +| | ... | aesni_gcm | ${${wt}} +| | And Add DPDK dev default RXD to all DUTs | 2048 +| | And Add DPDK dev default TXD to all DUTs | 2048 +| | And Apply startup configuration on all VPP DUTs +| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} +| | And Initialize IPSec in 3-node circular topology +| | And VPP IPsec Create Tunnel Interfaces +| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} +| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} +| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc02-64B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc03-1518B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc04-1518B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc05-IMIX-1t1c-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc06-IMIX-1t1c-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for IMIX_v4_1 frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 2 thread, 2 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 2 thread, 2 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-ndrpdrdisc.robot b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-ndrpdrdisc.robot new file mode 100644 index 0000000000..b0b542a495 --- /dev/null +++ b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-ndrpdrdisc.robot @@ -0,0 +1,212 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/crypto/ipsec.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | IP4FWD | IPSEC | IPSECSW | IPSECTUN | NIC_Intel-XL710 | BASE +| ... +| Suite Setup | Set up IPSec performance test suite | L3 | Intel-XL710 +| ... | SW_cryptodev +| ... +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *IPv4 IPsec tunnel mode performance test suite.* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 on TG-DUTn, +| ... | Eth-IPv4-IPSec on DUT1-DUT2 +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with DPDK SW +| ... | crypto devices and multiple IPsec tunnels between them. DUTs get IPv4 +| ... | traffic from TG, encrypt it and send to another DUT, where packets are +| ... | decrypted and sent back to TG. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in number +| ... | of packets transmitted. NDR is discovered for different +| ... | number of IPsec tunnels using binary search algorithms with configured +| ... | starting rate and final step that determines throughput measurement +| ... | resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, number of flows per flow-group equals to +| ... | number of IPSec tunnels) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and +| ... | static payload. MAC addresses are matching MAC addresses of the TG +| ... | node interfaces. Incrementing of IP.dst (IPv4 destination address) field +| ... | is applied to both streams. +| ... | *[Ref] Applicable standard specifications:* RFC4303 and RFC2544. + +*** Variables *** +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_limit} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +| ${tg_if1_ip4}= | 192.168.10.2 +| ${dut1_if1_ip4}= | 192.168.10.1 +| ${dut1_if2_ip4}= | 172.168.1.1 +| ${dut2_if1_ip4}= | 172.168.1.2 +| ${dut2_if2_ip4}= | 192.168.20.1 +| ${tg_if2_ip4}= | 192.168.20.2 +| ${raddr_ip4}= | 20.0.0.0 +| ${laddr_ip4}= | 10.0.0.0 +| ${addr_range}= | ${32} +| ${ipsec_overhead_gcm}= | ${54} +| ${n_tunnels}= | ${1} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4dst${n_tunnels} + +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} +| | ... | ${get_framesize} + ${ipsec_overhead_gcm} +| | ${max_rate}= | Set Variable If +| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | ${encr_alg}= | Crypto Alg AES CBC 128 +| | ${auth_alg}= | Integ Alg SHA1 96 +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Add DPDK SW cryptodev on DUTs in 3-node single-link circular topology +| | ... | aesni_mb | ${${wt}} +| | And Add DPDK dev default RXD to all DUTs | 2048 +| | And Add DPDK dev default TXD to all DUTs | 2048 +| | And Apply startup configuration on all VPP DUTs +| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} +| | And Initialize IPSec in 3-node circular topology +| | And VPP IPsec Create Tunnel Interfaces +| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} +| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} +| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc02-64B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc03-1518B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc04-1518B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc05-IMIX-1t1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc06-IMIX-1t1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for IMIX_v4_1 frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 2 thread, 2 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 2 thread, 2 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-ndrpdrdisc.robot b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-ndrpdrdisc.robot new file mode 100644 index 0000000000..fff80be824 --- /dev/null +++ b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-ndrpdrdisc.robot @@ -0,0 +1,215 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/crypto/ipsec.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | IP4FWD | IPSEC | IPSECSW | IPSECTUN | NIC_Intel-XL710 | BASE +| ... +| Suite Setup | Set up IPSec performance test suite | L3 | Intel-XL710 +| ... | SW_cryptodev +| ... +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *IPv4 IPsec tunnel mode performance test suite.* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 on TG-DUTn, +| ... | Eth-IPv4-IPSec on DUT1-DUT2 +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with DPDK SW +| ... | crypto devices and multiple IPsec tunnels between them. DUTs get IPv4 +| ... | traffic from TG, encrypt it and send to another DUT, where packets are +| ... | decrypted and sent back to TG. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in number +| ... | of packets transmitted. NDR is discovered for different +| ... | number of IPsec tunnels using binary search algorithms with configured +| ... | starting rate and final step that determines throughput measurement +| ... | resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, number of flows per flow-group equals to +| ... | number of IPSec tunnels) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and +| ... | static payload. MAC addresses are matching MAC addresses of the TG +| ... | node interfaces. Incrementing of IP.dst (IPv4 destination address) field +| ... | is applied to both streams. +| ... | *[Ref] Applicable standard specifications:* RFC4303 and RFC2544. + +*** Variables *** +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_limit} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +| ${tg_if1_ip4}= | 192.168.10.2 +| ${dut1_if1_ip4}= | 192.168.10.1 +| ${dut1_if2_ip4}= | 172.168.1.1 +| ${dut2_if1_ip4}= | 172.168.1.2 +| ${dut2_if2_ip4}= | 192.168.20.1 +| ${tg_if2_ip4}= | 192.168.20.2 +| ${raddr_ip4}= | 20.0.0.0 +| ${laddr_ip4}= | 10.0.0.0 +| ${addr_range}= | ${32} +| ${ipsec_overhead_gcm}= | ${54} +| ${n_tunnels}= | ${1} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4dst${n_tunnels} + +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} +| | ... | ${get_framesize} + ${ipsec_overhead_gcm} +| | ${max_rate}= | Set Variable If +| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | ${encr_alg}= | Crypto Alg AES GCM 128 +| | ${auth_alg}= | Integ Alg AES GCM 128 +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Add DPDK SW cryptodev on DUTs in 3-node single-link circular topology +| | ... | aesni_gcm | ${${wt}} +| | And Add DPDK dev default RXD to all DUTs | 2048 +| | And Add DPDK dev default TXD to all DUTs | 2048 +| | And Apply startup configuration on all VPP DUTs +| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} +| | And Initialize IPSec in 3-node circular topology +| | Vpp Route Add | ${dut1} | ${raddr_ip4} | 8 | ${dut2_if1_ip4} | ${dut1_if2} +| | Vpp Route Add | ${dut2} | ${laddr_ip4} | 8 | ${dut1_if2_ip4} | ${dut2_if1} +| | And VPP IPsec Add Multiple Tunnels +| | ... | ${dut1} | ${dut2} | ${dut1_if2} | ${dut2_if1} | ${n_tunnels} +| | ... | ${encr_alg} | ${encr_key} | ${auth_alg} | ${auth_key} +| | ... | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${laddr_ip4} | ${raddr_ip4} +| | ... | ${addr_range} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc02-64B-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc03-1518B-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc04-1518B-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc05-IMIX-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc06-IMIX-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for IMIX_v4_1 frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 2 thread, 2 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4ipsecbasetnlsw-ip4base-tnl-aes-gcm-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel AES GCM in each direction, configured\ +| | ... | with 2 thread, 2 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-ndrpdrdisc.robot b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-ndrpdrdisc.robot new file mode 100644 index 0000000000..28b6554394 --- /dev/null +++ b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-ndrpdrdisc.robot @@ -0,0 +1,215 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/crypto/ipsec.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | IP4FWD | IPSEC | IPSECSW | IPSECTUN | NIC_Intel-XL710 | BASE +| ... +| Suite Setup | Set up IPSec performance test suite | L3 | Intel-XL710 +| ... | SW_cryptodev +| ... +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *IPv4 IPsec tunnel mode performance test suite.* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 on TG-DUTn, +| ... | Eth-IPv4-IPSec on DUT1-DUT2 +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with DPDK SW +| ... | crypto devices and multiple IPsec tunnels between them. DUTs get IPv4 +| ... | traffic from TG, encrypt it and send to another DUT, where packets are +| ... | decrypted and sent back to TG. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in number +| ... | of packets transmitted. NDR is discovered for different +| ... | number of IPsec tunnels using binary search algorithms with configured +| ... | starting rate and final step that determines throughput measurement +| ... | resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, number of flows per flow-group equals to +| ... | number of IPSec tunnels) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and +| ... | static payload. MAC addresses are matching MAC addresses of the TG +| ... | node interfaces. Incrementing of IP.dst (IPv4 destination address) field +| ... | is applied to both streams. +| ... | *[Ref] Applicable standard specifications:* RFC4303 and RFC2544. + +*** Variables *** +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_limit} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +| ${tg_if1_ip4}= | 192.168.10.2 +| ${dut1_if1_ip4}= | 192.168.10.1 +| ${dut1_if2_ip4}= | 172.168.1.1 +| ${dut2_if1_ip4}= | 172.168.1.2 +| ${dut2_if2_ip4}= | 192.168.20.1 +| ${tg_if2_ip4}= | 192.168.20.2 +| ${raddr_ip4}= | 20.0.0.0 +| ${laddr_ip4}= | 10.0.0.0 +| ${addr_range}= | ${32} +| ${ipsec_overhead_gcm}= | ${54} +| ${n_tunnels}= | ${1} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4dst${n_tunnels} + +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} +| | ... | ${get_framesize} + ${ipsec_overhead_gcm} +| | ${max_rate}= | Set Variable If +| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | ${encr_alg}= | Crypto Alg AES CBC 128 +| | ${auth_alg}= | Integ Alg SHA1 96 +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Add DPDK SW cryptodev on DUTs in 3-node single-link circular topology +| | ... | aesni_mb | ${${wt}} +| | And Add DPDK dev default RXD to all DUTs | 2048 +| | And Add DPDK dev default TXD to all DUTs | 2048 +| | And Apply startup configuration on all VPP DUTs +| | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} +| | And Initialize IPSec in 3-node circular topology +| | Vpp Route Add | ${dut1} | ${raddr_ip4} | 8 | ${dut2_if1_ip4} | ${dut1_if2} +| | Vpp Route Add | ${dut2} | ${laddr_ip4} | 8 | ${dut1_if2_ip4} | ${dut2_if1} +| | And VPP IPsec Add Multiple Tunnels +| | ... | ${dut1} | ${dut2} | ${dut1_if2} | ${dut2_if1} | ${n_tunnels} +| | ... | ${encr_alg} | ${encr_key} | ${auth_alg} | ${auth_key} +| | ... | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${laddr_ip4} | ${raddr_ip4} +| | ... | ${addr_range} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc02-64B-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc03-1518B-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc04-1518B-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc05-IMIX-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc06-IMIX-1t1c-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for IMIX_v4_1 frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 2 thread, 2 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames\ +| | ... | using binary search start at 40GE linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4ipsecbasetnlsw-ip4base-tnl-cbc-sha1-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ +| | ... | with 2 thread, 2 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\ +| | ... | linerate, step 100kpps and loss tolerance of 0.5%. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with IPSec SW cryptodev +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR -- cgit 1.2.3-korg