From 7d7259ab1a065f0d1f849b29270514eacd3a1efe Mon Sep 17 00:00:00 2001 From: Peter Mikus Date: Thu, 25 Jul 2019 11:09:23 +0000 Subject: VPPD: Dot1Q Change-Id: I0d3c925ea4a6896a0df98db6ddaf4238e6291bf1 Signed-off-by: Peter Mikus --- .../eth2p-avf-dot1qip4-l2bdbasemaclrn-dev.robot | 74 ++++ tests/vpp/func/ip4/eth2p-dot1q-ip4base-func.robot | 106 ------ ...q--dot1ad-l2bdbasemaclrn-vlantrans12-func.robot | 394 --------------------- ...h2p-dot1q-l2bdbasemaclrn-vlantrans11-func.robot | 206 ----------- .../l2bd/eth4p-eth-l2bdbasemaclrn-l2shg-func.robot | 85 ----- ...p-dot1q--dot1ad-l2xcbase-vlantrans12-func.robot | 335 ------------------ .../eth2p-dot1q-l2xcbase-vlantrans11-func.robot | 171 --------- 7 files changed, 74 insertions(+), 1297 deletions(-) create mode 100644 tests/vpp/device/l2bd/eth2p-avf-dot1qip4-l2bdbasemaclrn-dev.robot delete mode 100644 tests/vpp/func/ip4/eth2p-dot1q-ip4base-func.robot delete mode 100644 tests/vpp/func/l2bd/eth2p-dot1q--dot1ad-l2bdbasemaclrn-vlantrans12-func.robot delete mode 100644 tests/vpp/func/l2bd/eth2p-dot1q-l2bdbasemaclrn-vlantrans11-func.robot delete mode 100644 tests/vpp/func/l2bd/eth4p-eth-l2bdbasemaclrn-l2shg-func.robot delete mode 100644 tests/vpp/func/l2xc/eth2p-dot1q--dot1ad-l2xcbase-vlantrans12-func.robot delete mode 100644 tests/vpp/func/l2xc/eth2p-dot1q-l2xcbase-vlantrans11-func.robot (limited to 'tests/vpp') diff --git a/tests/vpp/device/l2bd/eth2p-avf-dot1qip4-l2bdbasemaclrn-dev.robot b/tests/vpp/device/l2bd/eth2p-avf-dot1qip4-l2bdbasemaclrn-dev.robot new file mode 100644 index 0000000000..b75b89c879 --- /dev/null +++ b/tests/vpp/device/l2bd/eth2p-avf-dot1qip4-l2bdbasemaclrn-dev.robot @@ -0,0 +1,74 @@ +# Copyright (c) 2019 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY +| ... | NIC_Virtual | ETH | IP4FWD | BASE | DOT1Q | IP4BASE | DRV_AVF +| ... +| Suite Setup | Setup suite single link | avf | scapy +| Test Setup | Setup test +| Test Teardown | Tear down test | packet_trace +| ... +| Test Template | Local Template +| ... +| Documentation | *IPv4 routing with IEEE 802.1Q test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\ +| ... | single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. IEEE 802.1Q\ +| ... | tagging is applied on links between TG-DUT1. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\ +| ... | two static IPv4 /30 route entries. DUT1 is tested with ${nic_name}. +| ... | *[Ver] TG verification:* Test IPv4 packets are sent in one direction \ +| ... | by TG on link to DUT1; on receive TG verifies packets for correctness \ +| ... | and drops as applicable. +| ... | *[Ref] Applicable standard specifications:* IEEE 802.1q. + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so | avf_plugin.so +| ${nic_name}= | virtual +| ${overhead}= | ${4} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Ver] Make TG send ICMPv4 Echo Reqs in both directions between two\ +| | ... | of its interfaces to be switched by DUT to and from docker; verify\ +| | ... | all packets are received. +| | ... +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer. Type: integer +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | \${frame_size} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add DPDK no PCI to all DUTs +| | And Set Max Rate And Jumbo +| | And Apply startup configuration on all VPP DUTs | with_trace=${True} +| | When Initialize AVF interfaces +| | And Initialize layer interface +| | And Initialize layer dot1q +| | And Initialize L2 bridge domain +| | Then Send ICMPv4 bidirectionally and verify received packets +| | ... | ${tg} | ${tg_if1} | ${tg_if2} + +*** Test Cases *** +| tc01-68B-avf-dot1qip4-l2bdbasemaclrn-dev +| | [Tags] | 68B +| | frame_size=${68} | phy_cores=${0} diff --git a/tests/vpp/func/ip4/eth2p-dot1q-ip4base-func.robot b/tests/vpp/func/ip4/eth2p-dot1q-ip4base-func.robot deleted file mode 100644 index 123969a867..0000000000 --- a/tests/vpp/func/ip4/eth2p-dot1q-ip4base-func.robot +++ /dev/null @@ -1,106 +0,0 @@ -# Copyright (c) 2019 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Library | resources.libraries.python.IPv6Util -| Library | resources.libraries.python.Trace -| ... -| Resource | resources/libraries/robot/ip/ip4.robot -| Resource | resources/libraries/robot/l2/tagging.robot -| Resource | resources/libraries/robot/shared/default.robot -| Resource | resources/libraries/robot/shared/testing_path.robot -| Resource | resources/libraries/robot/shared/traffic.robot -| ... -| Force Tags | 3_NODE_DOUBLE_LINK_TOPO | VM_ENV | HW_ENV | VPP_VM_ENV -| ... | SKIP_VPP_PATCH -| Test Setup | Set up functional test -| Test Teardown | Tear down functional test -| Documentation | *IPv4 with VLAN subinterfaces* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology -| ... | with double links between nodes. -| ... | *[Enc] Packet encapsulations:* Eth-IPv4-ICMPv4 on TG-DUT1-IF1, -| ... | Eth-dot1q-IPv4-ICMPv4 on TG-DUT1-IF2. -| ... | *[Cfg] DUT configuration:* DUT1 is configured with 2 Vlan subinterfaces -| ... | on DUT1-IF2. The subinterfaces and DUT1-IF1 have IP addresses set and -| ... | corresponding IP neighbor entries are configured. -| ... | *[Ref] Applicable standard specifications:* IEEE 802.1q. - -*** Variables *** - -| ${ip4_net0_1}= | 192.168.0.1 -| ${ip4_net0_2}= | 192.168.0.2 -| ${ip4_net1_1}= | 192.168.100.1 -| ${ip4_net1_2}= | 192.168.100.2 -| ${ip4_net2_1}= | 192.168.200.1 -| ${ip4_net2_2}= | 192.168.200.2 -| ${ip4_prefix}= | 24 -| ${tag_1}= | ${10} -| ${tag_2}= | ${20} - -*** Test Cases *** -| TC01: Process untagged send tagged -| | Given Vlan Test Setup -| | Then Send packet and verify headers -| | ... | ${tg_node} | ${ip4_net0_2} | ${ip4_net2_2} | ${tg_to_dut_if1} -| | ... | ${tg_to_dut_if1_mac} | ${dut_to_tg_if1_mac} | ${tg_to_dut_if2} -| | ... | ${dut_to_tg_if2_mac} | ${tg_to_dut_if2_mac} -| | ... | encaps_rx=Dot1q | vlan_rx=${tag_2} - -| TC02: Process tagged send untagged -| | Given Vlan Test Setup -| | Then Send packet and verify headers -| | ... | ${tg_node} | ${ip4_net2_2} | ${ip4_net0_2} | ${tg_to_dut_if2} -| | ... | ${tg_to_dut_if2_mac} | ${dut_to_tg_if2_mac} | ${tg_to_dut_if1} -| | ... | ${dut_to_tg_if1_mac} | ${tg_to_dut_if1_mac} -| | ... | encaps_tx=Dot1q | vlan_tx=${tag_2} - -| TC03: Process tagged send tagged -| | Given Vlan Test Setup -| | Then Send packet and verify headers -| | ... | ${tg_node} | ${ip4_net1_2} | ${ip4_net2_2} | ${tg_to_dut_if2} -| | ... | ${tg_to_dut_if2_mac} | ${dut_to_tg_if2_mac} | ${tg_to_dut_if2} -| | ... | ${dut_to_tg_if2_mac} | ${tg_to_dut_if2_mac} -| | ... | encaps_tx=Dot1q | vlan_tx=${tag_1} -| | ... | encaps_rx=Dot1q | vlan_rx=${tag_2} -| | And Send packet and verify headers -| | ... | ${tg_node} | ${ip4_net2_2} | ${ip4_net1_2} | ${tg_to_dut_if2} -| | ... | ${tg_to_dut_if2_mac} | ${dut_to_tg_if2_mac} | ${tg_to_dut_if2} -| | ... | ${dut_to_tg_if2_mac} | ${tg_to_dut_if2_mac} -| | ... | encaps_tx=Dot1q | vlan_tx=${tag_2} -| | ... | encaps_rx=Dot1q | vlan_rx=${tag_1} - -*** Keywords *** -| Vlan Test Setup -| | Configure path in 2-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']} -| | Set interfaces in 2-node circular topology up -| | -| | ${vlan1_name} | ${vlan1_index}= | Create vlan sub-interface -| | ... | ${dut_node} | ${dut_to_tg_if2} | ${tag_1} -| | ${vlan2_name} | ${vlan2_index}= | Create vlan sub-interface -| | ... | ${dut_node} | ${dut_to_tg_if2} | ${tag_2} -| | -| | VPP Interface Set IP Address | ${dut_node} -| | ... | ${dut_to_tg_if1} | ${ip4_net0_1} | ${ip4_prefix} -| | VPP Interface Set IP Address | ${dut_node} -| | ... | ${vlan1_index} | ${ip4_net1_1} | ${ip4_prefix} -| | VPP Interface Set IP Address | ${dut_node} -| | ... | ${vlan2_index} | ${ip4_net2_1} | ${ip4_prefix} -| | -| | VPP Add IP Neighbor -| | ... | ${dut_node} | ${dut_to_tg_if1} | ${ip4_net0_2} | ${tg_to_dut_if1_mac} -| | VPP Add IP Neighbor -| | ... | ${dut_node} | ${vlan1_index} | ${ip4_net1_2} | ${tg_to_dut_if2_mac} -| | VPP Add IP Neighbor -| | ... | ${dut_node} | ${vlan2_index} | ${ip4_net2_2} | ${tg_to_dut_if2_mac} diff --git a/tests/vpp/func/l2bd/eth2p-dot1q--dot1ad-l2bdbasemaclrn-vlantrans12-func.robot b/tests/vpp/func/l2bd/eth2p-dot1q--dot1ad-l2bdbasemaclrn-vlantrans12-func.robot deleted file mode 100644 index e71e75f563..0000000000 --- a/tests/vpp/func/l2bd/eth2p-dot1q--dot1ad-l2bdbasemaclrn-vlantrans12-func.robot +++ /dev/null @@ -1,394 +0,0 @@ -# Copyright (c) 2016 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/shared/default.robot -| Resource | resources/libraries/robot/l2/l2_bridge_domain.robot -| Resource | resources/libraries/robot/shared/testing_path.robot -| Resource | resources/libraries/robot/l2/tagging.robot -| Resource | resources/libraries/robot/l2/l2_traffic.robot -| Library | resources.libraries.python.Trace -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | VM_ENV | SKIP_VPP_PATCH -| Test Setup | Set up functional test -| Test Teardown | Tear down functional test -| Documentation | *L2BD with VLAN tag rewrite test cases - translate-1-2* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet encapsulations:* Eth-dot1q-IPv4-ICMPv4 or -| ... | Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, Eth-dot1ad-IPv4-ICMPv4 or -| ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv4-ICMPv4 or Eth-IPv6-ICMPv6 -| ... | on TG-DUT2 for L2 switching of IPv4/IPv6. -| ... | *[Cfg] DUT configuration:* DUT1 is configured with bridge domain (L2BD) -| ... | switching combined with MAC learning enabled and added VLAN -| ... | sub-interface with VLAN tag rewrite translate-1-2 method of interface -| ... | towards TG and interface towards DUT2. DUT2 is configured with L2 -| ... | bridge domain (L2BD) switching between VLAN sub-interface with VLAN tag -| ... | rewrite pop-2 method of interface towards DUT1 and interface towards TG. -| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are -| ... | sent from TG on link to DUT1 and received in TG on link form DUT2; -| ... | on receive TG verifies packets for correctness and their IPv4 src-addr, -| ... | dst-addr and MAC addresses. -| ... | *[Ref] Applicable standard specifications:* IEEE 802.1q, IEEE 802.1ad. - -*** Variables *** -| ${bd_id1}= | 1 - -| ${subid}= | 10 - -| ${outer_vlan_id1}= | 110 -| ${outer_vlan_id2}= | 120 -| ${outer_vlan_wrong}= | 150 - -| ${inner_vlan_id1}= | 210 -| ${inner_vlan_id2}= | 220 -| ${inner_vlan_wrong}= | 250 - -| ${src_ip6}= | 3ffe:63::1 -| ${dst_ip6}= | 3ffe:63::2 - -*** Test Cases *** -| TC01: DUT1 and DUT2 with L2BD and VLAN translate-1-2 (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method; on DUT2 configure L2 bridge domain (L2BD) with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req -| | ... | tagged with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id1} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_id1} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} - -| TC02: DUT1 and DUT2 with L2BD and VLAN translate-1-2 with wrong inner tag used (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set inner tag different from inner tag set on -| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 bridge domain with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req -| | ... | tagged with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id1} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC03: DUT1 and DUT2 with L2BD and VLAN translate-1-2 with wrong outer tag used (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set outer tag different from outer tag set on -| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 bridge domain with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req -| | ... | tagged with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id1} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_id1} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC04: DUT1 and DUT2 with L2BD and VLAN translate-1-2 with wrong outer and inner tag used (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set outer and inner tags different from tags -| | ... | set on Dot1ad sub-interface of DUT2; on DUT2 configure L2 -| | ... | bridge domain with one interface to TG and one Dot1ad sub-interface -| | ... | towards DUT1 with VLAN tag rewrite pop-2 method. [Ver] Make TG send -| | ... | ICMPv4 Echo Req tagged with one Dot1q tag from one of its interfaces -| | ... | to another one via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id1} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC05: DUT1 and DUT2 with L2BD and VLAN translate-1-2 (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method; on DUT2 configure L2 bridge domain (L2BD) with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv6 Echo Req -| | ... | tagged with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | src_ip=${src_ip6} -| | ... | dst_ip=${dst_ip6} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC06: DUT1 and DUT2 with L2BD and VLAN translate-1-2 with wrong inner tag used (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set inner tag different from inner tag set on -| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 bridge domain with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv6 Echo Req -| | ... | tagged with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | src_ip=${src_ip6} | dst_ip=${dst_ip6} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} - -| TC07: DUT1 and DUT2 with L2BD and VLAN translate-1-2 with wrong outer tag used (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set outer tag different from outer tag set on -| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 bridge domain with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv6 Echo Req -| | ... | tagged with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | src_ip=${src_ip6} | dst_ip=${dst_ip6} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} - -| TC08: DUT1 and DUT2 with L2BD and VLAN translate-1-2 with wrong outer and inner tag used (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set outer and inner tags different from tags -| | ... | set on Dot1ad sub-interface of DUT2; on DUT2 configure L2 -| | ... | bridge domain with one interface to TG and one Dot1ad sub-interface -| | ... | towards DUT1 with VLAN tag rewrite pop-2 method. [Ver] Make TG send -| | ... | ICMPv6 Echo Req tagged with one Dot1q tag from one of its interfaces -| | ... | to another one via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | src_ip=${src_ip6} | dst_ip=${dst_ip6} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} diff --git a/tests/vpp/func/l2bd/eth2p-dot1q-l2bdbasemaclrn-vlantrans11-func.robot b/tests/vpp/func/l2bd/eth2p-dot1q-l2bdbasemaclrn-vlantrans11-func.robot deleted file mode 100644 index aba84789b1..0000000000 --- a/tests/vpp/func/l2bd/eth2p-dot1q-l2bdbasemaclrn-vlantrans11-func.robot +++ /dev/null @@ -1,206 +0,0 @@ -# Copyright (c) 2016 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/shared/default.robot -| Resource | resources/libraries/robot/l2/l2_bridge_domain.robot -| Resource | resources/libraries/robot/shared/testing_path.robot -| Resource | resources/libraries/robot/l2/tagging.robot -| Resource | resources/libraries/robot/l2/l2_traffic.robot -| Library | resources.libraries.python.Trace -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | VM_ENV | SKIP_VPP_PATCH -| Test Setup | Set up functional test -| Test Teardown | Tear down functional test -| Documentation | *L2BD with VLAN tag rewrite test cases - translate-1-1* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet encapsulations:* Eth-dot1q-IPv4-ICMPv4 or -| ... | Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and DUT1-DUT2, Eth-IPv4-ICMPv4 or -| ... | Eth-IPv6-ICMPv6 on TG-DUT2 for L2 switching of IPv4/IPv6. -| ... | *[Cfg] DUT configuration:* DUT1 is configured with bridge domain (L2BD) -| ... | switching combined with MAC learning enabled and added VLAN -| ... | sub-interface with VLAN tag rewrite translate-1-1 method of interface -| ... | towards TG and interface towards DUT2. DUT2 is configured with L2 -| ... | bridge domain (L2BD) switching between VLAN sub-interface with VLAN tag -| ... | rewrite pop-1 method of interface towards DUT1 and interface towards TG. -| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are -| ... | sent from TG on link to DUT1 and received in TG on link form DUT2; -| ... | on receive TG verifies packets for correctness and their IPv4 src-addr, -| ... | dst-addr and MAC addresses. -| ... | *[Ref] Applicable standard specifications:* IEEE 802.1q, IEEE 802.1ad. - -*** Variables *** -| ${bd_id1}= | 1 - -| ${subid}= | 10 - -| ${outer_vlan_id1}= | 110 -| ${outer_vlan_id2}= | 120 -| ${outer_vlan_wrong}= | 150 - -| ${inner_vlan_id1}= | 210 -| ${inner_vlan_wrong}= | 250 - -| ${src_ip6}= | 3ffe:63::1 -| ${dst_ip6}= | 3ffe:63::2 - -*** Test Cases *** -| TC01: DUT1 and DUT2 with L2BD and VLAN translate-1-1 (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | bridge domain with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method; -| | ... | on DUT2 configure L2 bridge domain (L2BD) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is received. [Ref] IEEE 802.1q -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} - -| TC02: DUT1 and DUT2 with L2BD and VLAN translate-1-1 with wrong tag used (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | bridge domain (L2BD) with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method -| | ... | to set tag different from tag set on VLAN sub-interface of DUT2; -| | ... | on DUT2 configure L2 bridge domain (L2BD) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is not received. [Ref] IEEE 802.1q -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC03: DUT1 and DUT2 with L2BD and VLAN translate-1-1 (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | bridge domain (L2BD) with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method; -| | ... | on DUT2 configure L2 bridge domain (L2BD) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv6 Echo Req tagged with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is received. [Ref] IEEE 802.1q -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | src_ip=${src_ip6} -| | ... | dst_ip=${dst_ip6} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC04: DUT1 and DUT2 with L2BD and VLAN translate-1-1 with wrong tag used (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | bridge domain (L2BD) with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method -| | ... | to set tag different from tag set on VLAN sub-interface of DUT2; -| | ... | on DUT2 configure L2 bridge domain (L2BD) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv6 Echo Req tagged with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is not received. [Ref] IEEE 802.1q -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${vlan1_index} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg} -| | ... | ${bd_id1} -| | And Add interface to bridge domain | ${dut2_node} | ${vlan2_index} -| | ... | ${bd_id1} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | src_ip=${src_ip6} | dst_ip=${dst_ip6} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} diff --git a/tests/vpp/func/l2bd/eth4p-eth-l2bdbasemaclrn-l2shg-func.robot b/tests/vpp/func/l2bd/eth4p-eth-l2bdbasemaclrn-l2shg-func.robot deleted file mode 100644 index 673a5a7699..0000000000 --- a/tests/vpp/func/l2bd/eth4p-eth-l2bdbasemaclrn-l2shg-func.robot +++ /dev/null @@ -1,85 +0,0 @@ -# Copyright (c) 2016 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/shared/default.robot -| Resource | resources/libraries/robot/l2/l2_bridge_domain.robot -| Resource | resources/libraries/robot/shared/testing_path.robot -| Library | resources.libraries.python.Trace -| Force Tags | HW_ENV | VM_ENV -| Test Setup | Set up functional test -| Test Teardown | Tear down functional test -| Documentation | *L2 bridge-domain test cases* -| ... -| ... | *[Top] Network Topologies:* TG=DUT1=DUT2=TG 3-node circular topology -| ... | with double parallel links. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-ICMPv4 for L2 switching of -| ... | IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6 use. Both apply -| ... | to all links. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 -| ... | bridge-domain (L2BD) switching combined with MAC learning enabled -| ... | and Split Horizon Groups (SHG). -| ... | *[Ver] TG verification:* Test ICMPv4 (or ICMPv6) Echo Request packets -| ... | are sent in both directions by TG on links to DUT1 and DUT2; on -| ... | receive TG verifies packets for correctness and their IPv4 (IPv6) -| ... | src-addr, dst-addr and MAC addresses. -| ... | *[Ref] Applicable standard specifications:* - -*** Variables *** -| ${bd_id1}= | 1 -| ${bd_id2}= | 2 - -| ${shg1}= | 3 -| ${shg2}= | 4 - -*** Test Cases *** -| TC01: DUT1 and DUT2 with L2BD (MAC learn) and SHG switch between four TG links -| | [Documentation] -| | ... | [Top] TG=DUT1=DUT2=TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 and \ -| | ... | DUT2 configure four i/fs into L2BD with MAC learning and the -| | ... | same SHG on i/fs towards TG. [Ver] Make TG verify ICMPv4 Echo -| | ... | Req pkts are switched thru DUT1 and DUT2 in both directions and -| | ... | are correct on receive; verify no pkts are switched thru SHG -| | ... | isolated interfaces. [Ref] -| | [Tags] | 3_NODE_DOUBLE_LINK_TOPO -| | Given Configure path for 3-node BD-SHG test | ${nodes['TG']} -| | ... | ${nodes['DUT1']} | ${nodes['DUT2']} -| | And Set interfaces in 3-node BD-SHG test up -| | When Create bridge domain | ${dut1_node} | ${bd_id1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_tg_if1} -| | ... | ${bd_id1} | ${shg1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_tg_if2} -| | ... | ${bd_id1} | ${shg1} -| | And Add interface to bridge domain | ${dut1_node} | ${dut1_to_dut2} -| | ... | ${bd_id1} -| | And Create bridge domain | ${dut2_node} | ${bd_id2} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg_if1} -| | ... | ${bd_id2} | ${shg2} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_tg_if2} -| | ... | ${bd_id2} | ${shg2} -| | And Add interface to bridge domain | ${dut2_node} | ${dut2_to_dut1} -| | ... | ${bd_id2} -| | Then Send ICMPv4 bidirectionally and verify received packets | ${tg_node} -| | ... | ${tg_to_dut1_if1} | ${tg_to_dut2_if1} -| | And Send ICMPv4 bidirectionally and verify received packets | ${tg_node} -| | ... | ${tg_to_dut1_if1} | ${tg_to_dut2_if2} -| | And Send ICMPv4 bidirectionally and verify received packets | ${tg_node} -| | ... | ${tg_to_dut1_if2} | ${tg_to_dut2_if1} -| | And Send ICMPv4 bidirectionally and verify received packets | ${tg_node} -| | ... | ${tg_to_dut1_if2} | ${tg_to_dut2_if2} -| | And Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMPv4 bidirectionally and verify received packets -| | | ... | ${tg_node} | ${tg_to_dut1_if1} | ${tg_to_dut1_if2} -| | And Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMPv4 bidirectionally and verify received packets -| | | ... | ${tg_node} | ${tg_to_dut2_if1} | ${tg_to_dut2_if2} diff --git a/tests/vpp/func/l2xc/eth2p-dot1q--dot1ad-l2xcbase-vlantrans12-func.robot b/tests/vpp/func/l2xc/eth2p-dot1q--dot1ad-l2xcbase-vlantrans12-func.robot deleted file mode 100644 index 6952d368b8..0000000000 --- a/tests/vpp/func/l2xc/eth2p-dot1q--dot1ad-l2xcbase-vlantrans12-func.robot +++ /dev/null @@ -1,335 +0,0 @@ -# Copyright (c) 2016 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/shared/default.robot -| Resource | resources/libraries/robot/shared/testing_path.robot -| Resource | resources/libraries/robot/l2/tagging.robot -| Resource | resources/libraries/robot/l2/l2_traffic.robot -| Library | resources.libraries.python.Trace -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | VM_ENV | SKIP_VPP_PATCH -| Test Setup | Set up functional test -| Test Teardown | Tear down functional test -| Documentation | *L2XC with VLAN tag rewrite test cases - translate-1-2* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet encapsulations:* Eth-dot1q-IPv4-ICMPv4 or -| ... | Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, Eth-dot1ad-IPv4-ICMPv4 or -| ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv4-ICMPv4 or Eth-IPv6-ICMPv6 -| ... | on TG-DUT2 for L2 switching of IPv4/IPv6. -| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect -| ... | (L2XC) switching between VLAN sub-interface with VLAN tag rewrite -| ... | translate-1-2 method of interface towards TG and interface towards DUT2. -| ... | DUT2 is configured configured with L2 cross-connect (L2XC) switching -| ... | between VLAN sub-interface with VLAN tag rewrite pop-2 method -| ... | of interface towards DUT1 and interface towards TG. -| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are -| ... | sent from TG on link to DUT1 and received in TG on link form DUT2; -| ... | on receive TG verifies packets for correctness and their IPv4 src-addr, -| ... | dst-addr and MAC addresses. -| ... | *[Ref] Applicable standard specifications:* IEEE 802.1q, IEEE 802.1ad. - -*** Variables *** -| ${subid}= | 10 - -| ${outer_vlan_id1}= | 110 -| ${outer_vlan_id2}= | 120 -| ${outer_vlan_wrong}= | 150 - -| ${inner_vlan_id1}= | 210 -| ${inner_vlan_id2}= | 220 -| ${inner_vlan_wrong}= | 250 - -| ${src_ip}= | 3ffe:63::1 -| ${dst_ip}= | 3ffe:63::2 - -*** Test Cases *** -| TC01: DUT1 and DUT2 with L2XC and VLAN translate-1-2 (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method; on DUT2 configure L2 cross-connect (L2XC) with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req -| | ... | tagged with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id1} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_id1} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} - -| TC02: DUT1 and DUT2 with L2XC and VLAN translate-1-2 with wrong inner tag used (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set inner tag different from inner tag set on -| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 cross-connect with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req -| | ... | tagged with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id1} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC03: DUT1 and DUT2 with L2XC and VLAN translate-1-2 with wrong outer tag used (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set outer tag different from outer tag set on -| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 cross-connect with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req -| | ... | tagged with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id1} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_id1} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC04: DUT1 and DUT2 with L2XC and VLAN translate-1-2 with wrong outer and inner tag used (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set outer and inner tags different from tags -| | ... | set on Dot1ad sub-interface of DUT2; on DUT2 configure L2 -| | ... | cross-connect with one interface to TG and one Dot1ad sub-interface -| | ... | towards DUT1 with VLAN tag rewrite pop-2 method. [Ver] Make TG send -| | ... | ICMPv4 Echo Req tagged with one Dot1q tag from one of its interfaces -| | ... | to another one via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id1} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC05: DUT1 and DUT2 with L2XC and VLAN translate-1-2 (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method; on DUT2 configure L2 cross-connect (L2XC) with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv6 Echo Req -| | ... | tagegd with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | src_ip=${src_ip} -| | ... | dst_ip=${dst_ip} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC06: DUT1 and DUT2 with L2XC and VLAN translate-1-2 with wrong inner tag used (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set inner tag different from inner tag set on -| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 cross-connect with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv6 Echo Req -| | ... | tagegd with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | src_ip=${src_ip} | dst_ip=${dst_ip} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} - -| TC07: DUT1 and DUT2 with L2XC and VLAN translate-1-2 with wrong outer tag used (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set outer tag different from outer tag set on -| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 cross-connect with -| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with -| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv6 Echo Req -| | ... | tagegd with one Dot1q tag from one of its interfaces to another one -| | ... | via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | src_ip=${src_ip} | dst_ip=${dst_ip} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} - -| TC08: DUT1 and DUT2 with L2XC and VLAN translate-1-2 with wrong outer and inner tag used (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, \ -| | ... | Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. -| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to -| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | translate-1-2 method to set outer and inner tags different from tags -| | ... | set on Dot1ad sub-interface of DUT2; on DUT2 configure L2 -| | ... | cross-connect with one interface to TG and one Dot1ad sub-interface -| | ... | towards DUT1 with VLAN tag rewrite pop-2 method. [Ver] Make TG send -| | ... | ICMPv6 Echo Req tagegd with one Dot1q tag from one of its interfaces -| | ... | to another one via DUT1 and DUT2; verify that packet is not received. -| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create tagged sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} -| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} -| | ... | type_subif=two_tags dot1ad -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} -| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-2 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | src_ip=${src_ip} | dst_ip=${dst_ip} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} diff --git a/tests/vpp/func/l2xc/eth2p-dot1q-l2xcbase-vlantrans11-func.robot b/tests/vpp/func/l2xc/eth2p-dot1q-l2xcbase-vlantrans11-func.robot deleted file mode 100644 index 49039e9db9..0000000000 --- a/tests/vpp/func/l2xc/eth2p-dot1q-l2xcbase-vlantrans11-func.robot +++ /dev/null @@ -1,171 +0,0 @@ -# Copyright (c) 2016 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/shared/default.robot -| Resource | resources/libraries/robot/shared/testing_path.robot -| Resource | resources/libraries/robot/l2/tagging.robot -| Resource | resources/libraries/robot/l2/l2_traffic.robot -| Library | resources.libraries.python.Trace -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | VM_ENV | SKIP_VPP_PATCH -| Test Setup | Set up functional test -| Test Teardown | Tear down functional test -| Documentation | *L2XC with VLAN tag rewrite test cases - translate-1-1* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet encapsulations:* Eth-dot1q-IPv4-ICMPv4 or -| ... | Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and DUT1-DUT2, Eth-IPv4-ICMPv4 or -| ... | Eth-IPv4-ICMPv4 on TG-DUT2 for L2 switching of IPv4/IPv6. -| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect -| ... | (L2XC) switching between VLAN sub-interface with VLAN tag rewrite -| ... | translate-1-1 method of interface towards TG and interface towards DUT2. -| ... | DUT2 is configured configured with L2 cross-connect (L2XC) switching -| ... | between VLAN sub-interface with VLAN tag rewrite pop-1 method -| ... | of interface towards DUT1 and interface towards TG. -| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are -| ... | sent from TG on link to DUT1 and received in TG on link form DUT2; -| ... | on receive TG verifies packets for correctness and their IPv4 src-addr, -| ... | dst-addr and MAC addresses. -| ... | *[Ref] Applicable standard specifications:* IEEE 802.1q, IEEE 802.1ad. - -*** Variables *** -| ${subid}= | 10 - -| ${outer_vlan_id1}= | 110 -| ${outer_vlan_id2}= | 120 -| ${outer_vlan_wrong}= | 150 - -| ${src_ip}= | 3ffe:63::1 -| ${dst_ip}= | 3ffe:63::2 - -*** Test Cases *** -| TC01: DUT1 and DUT2 with L2XC and VLAN translate-1-1 (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method; -| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is received. [Ref] IEEE 802.1q -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} - -| TC02: DUT1 and DUT2 with L2XC and VLAN translate-1-1 with wrong tag used (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | cross-connect (L2XC) with one VLAN tagged sub-interface to DUT2 and -| | ... | one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | (translate-1-1) on sub-interface to DUT2; on DUT2 configure L2XC with -| | ... | one interface to TG and one VLAN sub-interface towards DUT1 with VLAN -| | ... | tag pop-1. [Ver] Make TG send ICMPv4 Echo Req tagged with one dot1q -| | ... | tag from one of its interfaces to another one via DUT1 and DUT2; -| | ... | verify that packet is not received. [Ref] IEEE 802.1q -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC03: DUT1 and DUT2 with L2XC and VLAN translate-1-1 (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method; -| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv6 Echo Req tagegd with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is received. [Ref] IEEE 802.1q -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | src_ip=${src_ip} -| | ... | dst_ip=${dst_ip} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC04: DUT1 and DUT2 with L2XC and VLAN translate-1-1 with wrong tag used (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method -| | ... | to set tag different from tag set on VLAN sub-interface of DUT2; -| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv6 Echo Req tagegd with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is not received. [Ref] IEEE 802.1q -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | src_ip=${src_ip} | dst_ip=${dst_ip} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} -- cgit 1.2.3-korg