# Copyright (c) 2018 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Settings *** | Resource | resources/libraries/robot/performance/performance_setup.robot | ... | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR | ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS | ... | IACL | ACL50 | 10k_FLOWS | ... | Suite Setup | Run Keywords | ... | Set up 3-node performance topology with DUT's NIC model | L3 | ... | Intel-X710 | ... | AND | Set up performance test suite with ACL | Suite Teardown | Tear down 3-node performance topology | ... | Test Setup | Set up performance test | ... | Test Teardown | Tear down performance mrr test | ... | Documentation | *Raw results IPv4 test cases with ACL* | ... | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ | ... | with single links between nodes. | ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4. | ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\ | ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\ | ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\ | ... | DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.\ | ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic | ... | at line rate and reports total received/sent packets over trial period. | ... | Test packets are generated by TG on links to DUTs. TG traffic profile | ... | contains two L3 flow-groups (flow-group per direction, 253 flows per | ... | flow-group) with all packets containing Ethernet header, IPv4 header | ... | with IP protocol=61 and static payload. MAC addresses are matching MAC | ... | addresses of the TG node interfaces. | ... | *[Ref] Applicable standard specifications:* RFC2544. *** Variables *** # X710 bandwidth limit | ${s_limit}= | ${10000000000} # ACL test setup | ${acl_action}= | permit | ${acl_apply_type}= | input | ${no_hit_aces_number}= | 50 | ${flows_per_dir}= | 10k # starting points for non-hitting ACLs | ${src_ip_start}= | 30.30.30.1 | ${dst_ip_start}= | 40.40.40.1 | ${ip_step}= | ${1} | ${sport_start}= | ${1000} | ${dport_start}= | ${1000} | ${port_step}= | ${1} | ${trex_stream1_subnet}= | 10.10.10.0/24 | ${trex_stream2_subnet}= | 20.20.20.0/24 *** Keywords *** | Check RR for IPv4 routing with ACLs | | ... | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with ${wt} thread(s),\ | | ... | ${wt} phy core(s), ${rxq} receive queue(s) per NIC port. | | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ | | ... | trial throughput test. | | ... | | [Arguments] | ${wt} | ${rxq} | ${framesize} | | ... | | # Test Variables required for test execution and test teardown | | Set Test Variable | ${framesize} | | ${get_framesize}= | Get Frame Size | ${framesize} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ... | | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology | | And Add PCI devices to all DUTs | | And Run Keyword If | ${get_framesize} < ${1522} | | ... | Add no multi seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | ${ip_nr}= | Set Variable | 10 | | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology | | ${traffic_profile}= | Set Variable | trex-sl-3n-ethip4udp-10u1000p-conc | | Set Test Variable | ${traffic_profile} | | Then Traffic should pass with maximum rate | ${perf_trial_duration} | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} *** Test Cases *** | tc01-64B-1t1c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ | | ... | throughput test. | | ... | | [Tags] | 64B | 1T1C | STHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=1 | rxq=1 | framesize=${64} | tc02-1518B-1t1c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ | | ... | throughput test. | | ... | | [Tags] | 1518B | 1T1C | STHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=1 | rxq=1 | framesize=${1518} | tc03-9000B-1t1c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ | | ... | throughput test. | | ... | | [Tags] | 9000B | 1T1C | STHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=1 | rxq=1 | framesize=${9000} | tc04-IMIX-1t1c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ | | ... | throughput test. | | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) | | ... | | [Tags] | IMIX | 1T1C | STHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=1 | rxq=1 | framesize=IMIX_v4_1 | tc05-64B-2t2c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ | | ... | throughput test. | | ... | | [Tags] | 64B | 2T2C | MTHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=2 | rxq=1 | framesize=${64} | tc06-1518B-2t2c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ | | ... | throughput test. | | ... | | [Tags] | 1518B | 2T2C | MTHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=2 | rxq=1 | framesize=${1518} | tc07-9000B-2t2c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ | | ... | throughput test. | | ... | | [Tags] | 9000B | 2T2C | MTHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=2 | rxq=1 | framesize=${9000} | tc08-IMIX-2t2c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ | | ... | throughput test. | | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) | | ... | | [Tags] | IMIX | 2T2C | MTHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=2 | rxq=1 | framesize=IMIX_v4_1 | tc09-64B-4t4c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ | | ... | throughput test. | | ... | | [Tags] | 64B | 4T4C | MTHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=4 | rxq=2 | framesize=${64} | tc10-1518B-4t4c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ | | ... | throughput test. | | ... | | [Tags] | 1518B | 4T4C | MTHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=4 | rxq=2 | framesize=${1518} | tc11-9000B-4t4c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ | | ... | throughput test. | | ... | | [Tags] | 9000B | 4T4C | MTHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=4 | rxq=2 | framesize=${9000} | tc12-IMIX-4t4c-ethip4udp-ip4base-iacl50-stateless-flows10k-mrr | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ | | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. | | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ | | ... | throughput test. | | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) | | ... | | [Tags] | IMIX | 4T4C | MTHREAD | | ... | | [Template] | Check RR for IPv4 routing with ACLs | | wt=4 | rxq=2 | framesize=IMIX_v4_1