# 1.  Introduction:

This document will help to test sample app with DMM.

# 2.  Configuration files:

There are two configuration files need to modify for setting up the
topology.

release\\configure

**module\_config.json** is the stack module config file.

**rd\_config.json** is the rd config file.

<!-- -->

# 3.  JSON files configuration.

We need to setup configuration as given below.

# 3.1  module\_config.json for example:

```
{
    "default_stack_name": "kernel", /*when rd can't be find maybe
                                    choose the defualt one*/
    "module_list": [
    {
        "stack_name": "kernel",
        "function_name": "kernel_stack_register",
        "libname": "", /*library name, if loadtype is static, this maybe
                        null, */ /* else must give a library name*/
        "loadtype": "static", /*library load type: static or dynamic*/
        "deploytype": "1",
        "maxfd": "1024",
        "minfd": "0",
        "priorty": "1",
        "stackid": "0", /*must be ordered and not be repeated*/
        }
    ]
}
```

# 3.2  rd\_config.json for example:

```
{
"ip_route": [
    {
        "subnet": "192.165.1.1/16",
        "type": "nstack-kernel", /*output interface type, nstack-kernel:
                    indicate that this ip */ /* should go through linux protocol,
                    nstack-dpdk: go through stackx protocol*/
    },
    {
        "subnet": "172.16.25.125/16",
        "type": "nstack-kernel",
    }
]
"prot_route": [
        {
            "proto_type": "11",
            "type": "nstack-kernel",
        },
    ]
}
```
# 4.  Run sample APP:

-  **perf-test:**

    Add test code with kernel stack or userspace protocol stack


Usage:

After building the DMM, inside the DMM/release directory below perf-test app will be generated.

*kc_epoll, ks_epoll, vc_epoll, vs_epoll*


Examples : 

**With Kernel stack:**

server:
```
    #./ks_epoll -p 20000 -d 172.16.25.125 -a 10000 -s 172.16.25.126 -l 200 -t 5000000 -i 0 -f 1 -r 20000 -n 1 -w 10 -u 10000 -e 10 -x 1
```
client:
```
    #./kc_epoll -p 20000 -d 172.16.25.126 -a 10000 -s 172.16.25.125 -l 200 -t 5000000 -i 0 -f 1 -r 20000 -n 1 -w 10 -u 10000 -e 10 -x 1
```

**With DMM nStack:**

server:
```
    #./vs_epoll -p 20000 -d 172.16.25.125 -a 10000 -s 172.16.25.126 -l 200 -t 5000000 -i 0 -f 1 -r 20000 -n 1 -w 10 -u 10000 -e 10 -x 1
```
client:
```
    #./vc_epoll -p 20000 -d 172.16.25.126 -a 10000 -s 172.16.25.125 -l 200 -t 5000000 -i 0 -f 1 -r 20000 -n 1 -w 10 -u 10000 -e 10 -x 1
```

- **NGNIX**:

Nginx build process:

*step 1: Compile nginx code*

```
    #wget "http://hg.nginx.org/nginx"
    #cd nginx-1.1.15
    #./configure --with-ld-opt="-L /root/Work/xxx/release/lib64/ -lnStackAPI"
    #make
    #make install
```
Note:
    
    a. ./configure **--with-ld-opt="-L /root/xxx/DMM/release/lib64/ -lnStackAPI"** can be done if you want to use nStack otherwise just give the ./configure.
    b. Make sure before building edit the configurtaion if you want specific server IP.
    For Ex:
        Server: ifconfig eth3 172.16.25.125 netmask 255.255.255.224 up
        Client: ifconfig eth3 172.16.25.126 netmask 255.255.255.224 up

    nginx.conf file modifiecations:
        listen      172.16.25.125:80
        
*step 2: run the nginx code*

```
    #cd /usr/local/nginx/sbin
    #cp -r * ../../sbin
    #cd ../../sbin
    #./nginx
```
Note:
    
    if you want to run ./nginx with nStack then perform following before run
    a. export LD_LIBRARY_PATH=/root/xxx/DMM/release/lib64/
    b. export NSTACK_LOG_ON=DBG ##to display nStack consol logs.

*step 3: Check whether ngnix service is running.*

```
    #ps -ax | grep nginx
```
*step 4: Test the nginx server is up or not!*

At client board, perform below command and check the output:
```
    #curl http://172.16.25.125:80/    
```
Note:

    curl is the tool need to be installed to browse the html page in linux without GUI.