/* This is a version (aka dlmalloc) of malloc/free/realloc written by Doug Lea and released to the public domain, as explained at http://creativecommons.org/publicdomain/zero/1.0/ Send questions, comments, complaints, performance data, etc to dl@cs.oswego.edu * Version 2.8.6 Wed Aug 29 06:57:58 2012 Doug Lea Note: There may be an updated version of this malloc obtainable at ftp://gee.cs.oswego.edu/pub/misc/malloc.c Check before installing! * Quickstart This library is all in one file to simplify the most common usage: ftp it, compile it (-O3), and link it into another program. All of the compile-time options default to reasonable values for use on most platforms. You might later want to step through various compile-time and dynamic tuning options. For convenience, an include file for code using this malloc is at: ftp://gee.cs.oswego.edu/pub/misc/malloc-2.8.6.h You don't really need this .h file unless you call functions not defined in your system include files. The .h file contains only the excerpts from this file needed for using this malloc on ANSI C/C++ systems, so long as you haven't changed compile-time options about naming and tuning parameters. If you do, then you can create your own malloc.h that does include all settings by cutting at the point indicated below. Note that you may already by default be using a C library containing a malloc that is based on some version of this malloc (for example in linux). You might still want to use the one in this file to customize settings or to avoid overheads associated with library versions. * Vital statistics: Supported pointer/size_t representation: 4 or 8 bytes size_t MUST be an unsigned type of the same width as pointers. (If you are using an ancient system that declares size_t as a signed type, or need it to be a different width than pointers, you can use a previous release of this malloc (e.g. 2.7.2) supporting these.) Alignment: 8 bytes (minimum) This suffices for nearly all current machines and C compilers. However, you can define MALLOC_ALIGNMENT to be wider than this if necessary (up to 128bytes), at the expense of using more space. Minimum overhead per allocated chunk: 4 or 8 bytes (if 4byte sizes) 8 or 16 bytes (if 8byte sizes) Each malloced chunk has a hidden word of overhead holding size and status information, and additional cross-check word if FOOTERS is defined. Minimum allocated size: 4-byte ptrs: 16 bytes (including overhead) 8-byte ptrs: 32 bytes (including overhead) Even a request for zero bytes (i.e., malloc(0)) returns a pointer to something of the minimum allocatable size. The maximum overhead wastage (i.e., number of extra bytes allocated than were requested in malloc) is less than or equal to the minimum size, except for requests >= mmap_threshold that are serviced via mmap(), where the worst case wastage is about 32 bytes plus the remainder from a system page (the minimal mmap unit); typically 4096 or 8192 bytes. Security: static-safe; optionally more or less The "security" of malloc refers to the ability of malicious code to accentuate the effects of errors (for example, freeing space that is not currently malloc'ed or overwriting past the ends of chunks) in code that calls malloc. This malloc guarantees not to modify any memory locations below the base of heap, i.e., static variables, even in the presence of usage errors. The routines additionally detect most improper frees and reallocs. All this holds as long as the static bookkeeping for malloc itself is not corrupted by some other means. This is only one aspect of security -- these checks do not, and cannot, detect all possible programming errors. If FOOTERS is defined nonzero, then each allocated chunk carries an additional check word to verify that it was malloced from its space. These check words are the same within each execution of a program using malloc, but differ across executions, so externally crafted fake chunks cannot be freed. This improves security by rejecting frees/reallocs that could corrupt heap memory, in addition to the checks preventing writes to statics that are always on. This may further improve security at the expense of time and space overhead. (Note that FOOTERS may also be worth using with MSPACES.) By default detected errors cause the program to abort (calling "abort()"). You can override this to instead proceed past errors by defining PROCEED_ON_ERROR. In this case, a bad free has no effect, and a malloc that encounters a bad address caused by user overwrites will ignore the bad address by dropping pointers and indices to all known memory. This may be appropriate for programs that should continue if at all possible in the face of programming errors, although they may run out of memory because dropped memory is never reclaimed. If you don't like either of these options, you can define CORRUPTION_ERROR_ACTION and USAGE_ERROR_ACTION to do anything else. And if if you are sure that your program using malloc has no errors or vulnerabilities, you can define INSECURE to 1, which might (or might not) provide a small performance improvement. It is also possible to limit the maximum total allocatable space, using malloc_set_footprint_limit. This is not designed as a security feature in itself (calls to set limits are not screened or privileged), but may be useful as one aspect of a secure implementation. Thread-safety: NOT thread-safe unless USE_LOCKS defined non-zero When USE_LOCKS is defined, each public call to malloc, free, etc is surrounded with a lock. By default, this uses a plain pthread mutex, win32 critical section, or a spin-lock if if available for the platform and not disabled by setting USE_SPIN_LOCKS=0. However, if USE_RECURSIVE_LOCKS is defined, recursive versions are used instead (which are not required for base functionality but may be needed in layered extensions). Using a global lock is not especially fast, and can be a major bottleneck. It is designed only to provide minimal protection in concurrent environments, and to provide a basis for extensions. If you are using malloc in a concurrent program, consider instead using nedmalloc (http://www.nedprod.com/programs/portable/nedmalloc/) or ptmalloc (See http://www.malloc.de), which are derived from versions of this malloc. System requirements: Any combination of MORECORE and/or MMAP/MUNMAP This malloc can use unix sbrk or any emulation (invoked using the CALL_MORECORE macro) and/or mmap/munmap or any emulation (invoked using CALL_MMAP/CALL_MUNMAP) to get and release system memory. On most unix systems, it tends to work best if both MORECORE and MMAP are enabled. On Win32, it uses emulations based on VirtualAlloc. It also uses common C library functions like memset. Compliance: I believe it is compliant with the Single Unix Specification (See http://www.unix.org). Also SVID/XPG, ANSI C, and probably others as well. * Overview of algorithms This is not the fastest, most space-conserving, most portable, or most tunable malloc ever written. However it is among the fastest while also being among the most space-conserving, portable and tunable. Consistent balance across these factors results in a good general-purpose allocator for malloc-intensive programs. In most ways, this malloc is a best-fit allocator. Generally, it chooses the best-fitting existing chunk for a request, with ties broken in approximately least-recently-used order. (This strategy normally maintains low fragmentation.) However, for requests less than 256bytes, it deviates from best-fit when there is not an exactly fitting available chunk by preferring to use space adjacent to that used for the previous small request, as well as by breaking ties in approximately most-recently-used order. (These enhance locality of series of small allocations.) And for very large requests (>= 256Kb by default), it relies on system memory mapping facilities, if supported. (This helps avoid carrying around and possibly fragmenting memory used only for large chunks.) All operations (except malloc_stats and mallinfo) have execution times that are bounded by a constant factor of the number of bits in a size_t, not counting any clearing in calloc or copying in realloc, or actions surrounding MORECORE and MMAP that have times proportional to the number of non-contiguous regions returned by system allocation routines, which is often just 1. In real-time applications, you can optionally suppress segment traversals using NO_SEGMENT_TRAVERSAL, which assures bounded execution even when system allocators return non-contiguous spaces, at the typical expense of carrying around more memory and increased fragmentation. The implementation is not very modular and seriously overuses macros. Perhaps someday all C compilers will do as good a job inlining modular code as can now be done by brute-force expansion, but now, enough of them seem not to. Some compilers issue a lot of warnings about code that is dead/unreachable only on some platforms, and also about intentional uses of negation on unsigned types. All known cases of each can be ignored. For a longer but out of date high-level description, see http://gee.cs.oswego.edu/dl/html/malloc.html * MSPACES If MSPACES is defined, then in addition to malloc, free, etc., this file also defines mspace_malloc, mspace_free, etc. These are versions of malloc routines that take an "mspace" argument obtained using create_mspace, to control all internal bookkeeping. If ONLY_MSPACES is defined, only these versions are compiled. So if you would like to use this allocator for only some allocations, and your system malloc for others, you can compile with ONLY_MSPACES and then do something like... static mspace mymspace = create_mspace(0,0); // for example #define mymalloc(bytes) mspace_malloc(mymspace, bytes) (Note: If you only need one instance of an mspace, you can instead use "USE_DL_PREFIX" to relabel the global malloc.) You can similarly create thread-local allocators by storing mspaces as thread-locals. For example: static __thread mspace tlms = 0; void* tlmalloc(size_t bytes) { if (tlms == 0) tlms = create_mspace(0, 0); return mspace_malloc(tlms, bytes); } void tlfree(void* mem) { mspace_free(tlms, mem); } Unless FOOTERS is defined, each mspace is completely independent. You cannot allocate from one and free to another (although conformance is only weakly checked, so usage errors are not always caught). If FOOTERS is defined, then each chunk carries around a tag indicating its originating mspace, and frees are directed to their originating spaces. Normally, this requires use of locks. ------------------------- Compile-time options --------------------------- Be careful in setting #define values for numerical constants of type size_t. On some systems, literal values are not automatically extended to size_t precision unless they are explicitly casted. You can also use the symbolic values MAX_SIZE_T, SIZE_T_ONE, etc below. WIN32 default: defined if _WIN32 defined Defining WIN32 sets up defaults for MS environment and compilers. Otherwise defaults are for unix. Beware that there seem to be some cases where this malloc might not be a pure drop-in replacement for Win32 malloc: Random-looking failures from Win32 GDI API's (eg; SetDIBits()) may be due to bugs in some video driver implementations when pixel buffers are malloc()ed, and the region spans more than one VirtualAlloc()ed region. Because dlmalloc uses a small (64Kb) default granularity, pixel buffers may straddle virtual allocation regions more often than when using the Microsoft allocator. You can avoid this by using VirtualAlloc() and VirtualFree() for all pixel buffers rather than using malloc(). If this is not possible, recompile this malloc with a larger DEFAULT_GRANULARITY. Note: in cases where MSC and gcc (cygwin) are known to differ on WIN32, conditions use _MSC_VER to distinguish them. DLMALLOC_EXPORT default: extern Defines how public APIs are declared. If you want to export via a Windows DLL, you might define this as #define DLMALLOC_EXPORT extern __declspec(dllexport) If you want a POSIX ELF shared object, you might use #define DLMALLOC_EXPORT extern __attribute__((visibility("default"))) MALLOC_ALIGNMENT default: (size_t)(2 * sizeof(void *)) Controls the minimum alignment for malloc'ed chunks. It must be a power of two and at least 8, even on machines for which smaller alignments would suffice. It may be defined as larger than this though. Note however that code and data structures are optimized for the case of 8-byte alignment. MSPACES default: 0 (false) If true, compile in support for independent allocation spaces. This is only supported if HAVE_MMAP is true. ONLY_MSPACES default: 0 (false) If true, only compile in mspace versions, not regular versions. USE_LOCKS default: 0 (false) Causes each call to each public routine to be surrounded with pthread or WIN32 mutex lock/unlock. (If set true, this can be overridden on a per-mspace basis for mspace versions.) If set to a non-zero value other than 1, locks are used, but their implementation is left out, so lock functions must be supplied manually, as described below. USE_SPIN_LOCKS default: 1 iff USE_LOCKS and spin locks available If true, uses custom spin locks for locking. This is currently supported only gcc >= 4.1, older gccs on x86 platforms, and recent MS compilers. Otherwise, posix locks or win32 critical sections are used. USE_RECURSIVE_LOCKS default: not defined If defined nonzero, uses recursive (aka reentrant) locks, otherwise uses plain mutexes. This is not required for malloc proper, but may be needed for layered allocators such as nedmalloc. LOCK_AT_FORK default: not defined If defined nonzero, performs pthread_atfork upon initialization to initialize child lock while holding parent lock. The implementation assumes that pthread locks (not custom locks) are being used. In other cases, you may need to customize the implementation. FOOTERS default: 0 If true, provide extra checking and dispatching by placing information in the footers of allocated chunks. This adds space and time overhead. INSECURE default: 0 If true, omit checks for usage errors and heap space overwrites. USE_DL_PREFIX default: NOT defined Causes compiler to prefix all public routines with the string 'dl'. This can be useful when you only want to use this malloc in one part of a program, using your regular system malloc elsewhere. MALLOC_INSPECT_ALL default: NOT defined If defined, compiles malloc_inspect_all and mspace_inspect_all, that perform traversal of all heap space. Unless access to these functions is otherwise restricted, you probably do not want to include them in secure implementations. DLM_ABORT default: defined as abort() Defines how to abort on failed checks. On most systems, a failed check cannot die with an "assert" or even print an informative message, because the underlying print routines in turn call malloc, which will fail again. Generally, the best policy is to simply call abort(). It's not very useful to do more than this because many errors due to overwriting will show up as address faults (null, odd addresses etc) rather than malloc-triggered checks, so will also abort. Also, most compilers know that abort() does not return, so can better optimize code conditionally calling it. PROCEED_ON_ERROR default: defined as 0 (false) Controls whether detected bad addresses cause them to bypassed rather than aborting. If set, detected bad arguments to free and realloc are ignored. And all bookkeeping information is zeroed out upon a detected overwrite of freed heap space, thus losing the ability to ever return it from malloc again, but enabling the application to proceed. If PROCEED_ON_ERROR is defined, the static variable malloc_corruption_error_count is compiled in and can be examined to see if errors have occurred. This option generates slower code than the default abort policy. DEBUG default: NOT defined The DEBUG setting is mainly intended for people trying to modify this code or diagnose problems when porting to new platforms. However, it may also be able to better isolate user errors than just using runtime checks. The assertions in the check routines spell out in more detail the assumptions and invariants underlying the algorithms. The checking is fairly extensive, and will slow down execution noticeably. Calling malloc_stats or mallinfo with DEBUG set will attempt to check every non-mmapped allocated and free chunk in the course of computing the summaries. DLM_ABORT_ON_ASSERT_FAILURE default: defined as 1 (true) Debugging assertion failures can be nearly impossible if your version of the assert macro causes malloc to be called, which will lead to a cascade of further failures, blowing the runtime stack. DLM_ABORT_ON_ASSERT_FAILURE cause assertions failures to call abort(), which will usually make debugging easier. MALLOC_FAILURE_ACTION default: sets errno to ENOMEM, or no-op on win32 The action to take before "return 0" when malloc fails to be able to return memory because there is none available. HAVE_MORECORE default: 1 (true) unless win32 or ONLY_MSPACES True if this system supports sbrk or an emulation of it. MORECORE default: sbrk The name of the sbrk-style system routine to call to obtain more memory. See below for guidance on writing custom MORECORE functions. The type of the argument to sbrk/MORECORE varies across systems. It cannot be size_t, because it supports negative arguments, so it is normally the signed type of the same width as size_t (sometimes declared as "intptr_t"). It doesn't much matter though. Internally, we only call it with arguments less than half the max value of a size_t, which should work across all reasonable possibilities, although sometimes generating compiler warnings. MORECORE_CONTIGUOUS default: 1 (true) if HAVE_MORECORE If true, take advantage of fact that consecutive calls to MORECORE with positive arguments always return contiguous increasing addresses. This is true of unix sbrk. It does not hurt too much to set it true anyway, since malloc copes with non-contiguities. Setting it false when definitely non-contiguous saves time and possibly wasted space it would take to discover this though. MORECORE_CANNOT_TRIM default: NOT defined True if MORECORE cannot release space back to the system when given negative arguments. This is generally necessary only if you are using a hand-crafted MORECORE function that cannot handle negative arguments. NO_SEGMENT_TRAVERSAL default: 0 If non-zero, suppresses traversals of memory segments returned by either MORECORE or CALL_MMAP. This disables merging of segments that are contiguous, and selectively releasing them to the OS if unused, but bounds execution times. HAVE_MMAP default: 1 (true) True if this system supports mmap or an emulation of it. If so, and HAVE_MORECORE is not true, MMAP is used for all system allocation. If set and HAVE_MORECORE is true as well, MMAP is primarily used to directly allocate very large blocks. It is also used as a backup strategy in cases where MORECORE fails to provide space from system. Note: A single call to MUNMAP is assumed to be able to unmap memory that may have be allocated using multiple calls to MMAP, so long as they are adjacent. HAVE_MREMAP default: 1 on linux, else 0 If true realloc() uses mremap() to re-allocate large blocks and extend or shrink allocation spaces. MMAP_CLEARS default: 1 except on WINCE. True if mmap clears memory so calloc doesn't need to. This is true for standard unix mmap using /dev/zero and on WIN32 except for WINCE. USE_BUILTIN_FFS default: 0 (i.e., not used) Causes malloc to use the builtin ffs() function to compute indices. Some compilers may recognize and intrinsify ffs to be faster than the supplied C version. Also, the case of x86 using gcc is special-cased to an asm instruction, so is already as fast as it can be, and so this setting has no effect. Similarly for Win32 under recent MS compilers. (On most x86s, the asm version is only slightly faster than the C version.) malloc_getpagesize default: derive from system includes, or 4096. The system page size. To the extent possible, this malloc manages memory from the system in page-size units. This may be (and usually is) a function rather than a constant. This is ignored if WIN32, where page size is determined using getSystemInfo during initialization. USE_DEV_RANDOM default: 0 (i.e., not used) Causes malloc to use /dev/random to initialize secure magic seed for stamping footers. Otherwise, the current time is used. NO_MALLINFO default: 0 If defined, don't compile "mallinfo". This can be a simple way of dealing with mismatches between system declarations and those in this file. MALLINFO_FIELD_TYPE default: size_t The type of the fields in the mallinfo struct. This was originally defined as "int" in SVID etc, but is more usefully defined as size_t. The value is used only if HAVE_USR_INCLUDE_MALLOC_H is not set NO_MALLOC_STATS default: 0 If defined, don't compile "malloc_stats". This avoids calls to fprintf and bringing in stdio dependencies you might not want. REALLOC_ZERO_BYTES_FREES default: not defined This should be set if a call to realloc with zero bytes should be the same as a call to free. Some people think it should. Otherwise, since this malloc returns a unique pointer for malloc(0), so does realloc(p, 0). LACKS_UNISTD_H, LACKS_FCNTL_H, LACKS_SYS_PARAM_H, LACKS_SYS_MMAN_H LACKS_STRINGS_H, LACKS_STRING_H, LACKS_SYS_TYPES_H, LACKS_ERRNO_H LACKS_STDLIB_H LACKS_SCHED_H LACKS_TIME_H default: NOT defined unless on WIN32 Define these if your system does not have these header files. You might need to manually insert some of the declarations they provide. DEFAULT_GRANULARITY default: page size if MORECORE_CONTIGUOUS, system_info.dwAllocationGranularity in WIN32, otherwise 64K. Also settable using mallopt(M_GRANULARITY, x) The unit for allocating and deallocating memory from the system. On most systems with contiguous MORECORE, there is no reason to make this more than a page. However, systems with MMAP tend to either require or encourage larger granularities. You can increase this value to prevent system allocation functions to be called so often, especially if they are slow. The value must be at least one page and must be a power of two. Setting to 0 causes initialization to either page size or win32 region size. (Note: In previous versions of malloc, the equivalent of this option was called "TOP_PAD") DEFAULT_TRIM_THRESHOLD default: 2MB Also settable using mallopt(M_TRIM_THRESHOLD, x) The maximum amount of unused top-most memory to keep before releasing via malloc_trim in free(). Automatic trimming is mainly useful in long-lived programs using contiguous MORECORE. Because trimming via sbrk can be slow on some systems, and can sometimes be wasteful (in cases where programs immediately afterward allocate more large chunks) the value should be high enough so that your overall system performance would improve by releasing this much memory. As a rough guide, you might set to a value close to the average size of a process (program) running on your system. Releasing this much memory would allow such a process to run in memory. Generally, it is worth tuning trim thresholds when a program undergoes phases where several large chunks are allocated and released in ways that can reuse each other's storage, perhaps mixed with phases where there are no such chunks at all. The trim value must be greater than page size to have any useful effect. To disable trimming completely, you can set to MAX_SIZE_T. Note that the trick some people use of mallocing a huge space and then freeing it at program startup, in an attempt to reserve system memory, doesn't have the intended effect under automatic trimming, since that memory will immediately be returned to the system. DEFAULT_MMAP_THRESHOLD default: 256K Also settable using mallopt(M_MMAP_THRESHOLD, x) The request size threshold for using MMAP to directly service a request. Requests of at least this size that cannot be allocated using already-existing space will be serviced via mmap. (If enough normal freed space already exists it is used instead.) Using mmap segregates relatively large chunks of memory so that they can be individually obtained and released from the host system. A request serviced through mmap is never reused by any other request (at least not directly; the system may just so happen to remap successive requests to the same locations). Segregating space in this way has the benefits that: Mmapped space can always be individually released back to the system, which helps keep the system level memory demands of a long-lived program low. Also, mapped memory doesn't become `locked' between other chunks, as can happen with normally allocated chunks, which means that even trimming via malloc_trim would not release them. However, it has the disadvantage that the space cannot be reclaimed, consolidated, and then used to service later requests, as happens with normal chunks. The advantages of mmap nearly always outweigh disadvantages for "large" chunks, but the value of "large" may vary across systems. The default is an empirically derived value that works well in most systems. You can disable mmap by setting to MAX_SIZE_T. MAX_RELEASE_CHECK_RATE default: 4095 unless not HAVE_MMAP The number of consolidated frees between checks to release unused segments when freeing. When using non-contiguous segments, especially with multiple mspaces, checking only for topmost space doesn't always suffice to trigger trimming. To compensate for this, free() will, with a period of MAX_RELEASE_CHECK_RATE (or the current number of segments, if greater) try to release unused segments to the OS when freeing chunks that result in consolidation. The best value for this parameter is a compromise between slowing down frees with relatively costly checks that rarely trigger versus holding on to unused memory. To effectively disable, set to MAX_SIZE_T. This may lead to a very slight speed improvement at the expense of carrying around more memory. */ #include <vppinfra/clib.h> #include <vppinfra/cache.h> /* --- begin vpp customizations --- */ #if CLIB_DEBUG > 0 #define FOOTERS 1 /* extra debugging */ #define DLM_MAGIC_CONSTANT 0xdeaddabe #endif #define USE_LOCKS 1 #define DLM_ABORT {extern void os_panic(void); os_panic(); abort();} #define ONLY_MSPACES 1 /* --- end vpp customizations --- */ /* Version identifier to allow people to support multiple versions */ #ifndef DLMALLOC_VERSION #define DLMALLOC_VERSION 20806 #endif /* DLMALLOC_VERSION */ #ifndef DLMALLOC_EXPORT #define DLMALLOC_EXPORT extern #endif #ifndef WIN32 #ifdef _WIN32 #define WIN32 1 #endif /* _WIN32 */ #ifdef _WIN32_WCE #define LACKS_FCNTL_H #define WIN32 1 #endif /* _WIN32_WCE */ #endif /* WIN32 */ #ifdef WIN32 #define WIN32_LEAN_AND_MEAN #include <windows.h> #include <tchar.h> #define HAVE_MMAP 1 #define HAVE_MORECORE 0 #define LACKS_UNISTD_H #define LACKS_SYS_PARAM_H #define LACKS_SYS_MMAN_H #define LACKS_STRING_H #define LACKS_STRINGS_H #define LACKS_SYS_TYPES_H #define LACKS_ERRNO_H #define LACKS_SCHED_H #ifndef MALLOC_FAILURE_ACTION #define MALLOC_FAILURE_ACTION #endif /* MALLOC_FAILURE_ACTION */ #ifndef MMAP_CLEARS #ifdef _WIN32_WCE /* WINCE reportedly does not clear */ #define MMAP_CLEARS 0 #else #define MMAP_CLEARS 1 #endif /* _WIN32_WCE */ #endif /*MMAP_CLEARS */ #endif /* WIN32 */ #if defined(DARWIN) || defined(_DARWIN) /* Mac OSX docs advise not to use sbrk; it seems better to use mmap */ #ifndef HAVE_MORECORE #define HAVE_MORECORE 0 #define HAVE_MMAP 1 /* OSX allocators provide 16 byte alignment */ #ifndef MALLOC_ALIGNMENT #define MALLOC_ALIGNMENT ((size_t)16U) #endif #endif /* HAVE_MORECORE */ #endif /* DARWIN */ #ifndef LACKS_SYS_TYPES_H #include <sys/types.h> /* For size_t */ #endif /* LACKS_SYS_TYPES_H */ /* The maximum possible size_t value has all bits set */ #define MAX_SIZE_T (~(size_t)0) #ifndef USE_LOCKS /* ensure true if spin or recursive locks set */ #define USE_LOCKS ((defined(USE_SPIN_LOCKS) && USE_SPIN_LOCKS != 0) || \ (defined(USE_RECURSIVE_LOCKS) && USE_RECURSIVE_LOCKS != 0)) #endif /* USE_LOCKS */ #if USE_LOCKS /* Spin locks for gcc >= 4.1, older gcc on x86, MSC >= 1310 */ #if ((defined(__GNUC__) && \ ((__GNUC__ > 4 || (__GNUC__ == 4 && __GNUC_MINOR__ >= 1)) || \ defined(__i386__) || defined(__x86_64__))) || \ (defined(_MSC_VER) && _MSC_VER>=1310)) #ifndef USE_SPIN_LOCKS #define USE_SPIN_LOCKS 1 #endif /* USE_SPIN_LOCKS */ #elif USE_SPIN_LOCKS #error "USE_SPIN_LOCKS defined without implementation" #endif /* ... locks available... */ #elif !defined(USE_SPIN_LOCKS) #define USE_SPIN_LOCKS 0 #endif /* USE_LOCKS */ #ifndef ONLY_MSPACES #define ONLY_MSPACES 1 #endif /* ONLY_MSPACES */ #ifndef MSPACES #if ONLY_MSPACES #define MSPACES 1 #else /* ONLY_MSPACES */ #define MSPACES 0 #endif /* ONLY_MSPACES */ #endif /* MSPACES */ #ifndef MALLOC_ALIGNMENT #define MALLOC_ALIGNMENT ((size_t)(2 * sizeof(void *))) #endif /* MALLOC_ALIGNMENT */ #ifndef FOOTERS #define FOOTERS 0 #endif /* FOOTERS */ #ifndef DLM_ABORT #define DLM_ABORT abort() #endif /* DLM_ABORT */ #ifndef DLM_ABORT_ON_ASSERT_FAILURE #define DLM_ABORT_ON_ASSERT_FAILURE 1 #endif /* DLM_ABORT_ON_ASSERT_FAILURE */ #ifndef PROCEED_ON_ERROR #define PROCEED_ON_ERROR 0 #endif /* PROCEED_ON_ERROR */ #ifndef INSECURE #define INSECURE 0 #endif /* INSECURE */ #ifndef MALLOC_INSPECT_ALL #define MALLOC_INSPECT_ALL 0 #endif /* MALLOC_INSPECT_ALL */ #ifndef HAVE_MMAP #define HAVE_MMAP 1 #endif /* HAVE_MMAP */ #ifndef MMAP_CLEARS #define MMAP_CLEARS 1 #endif /* MMAP_CLEARS */ #ifndef HAVE_MREMAP #ifdef linux #define HAVE_MREMAP 1 #define _GNU_SOURCE /* Turns on mremap() definition */ #else /* linux */ #define HAVE_MREMAP 0 #endif /* linux */ #endif /* HAVE_MREMAP */ #ifndef MALLOC_FAILURE_ACTION #define MALLOC_FAILURE_ACTION errno = ENOMEM; #endif /* MALLOC_FAILURE_ACTION */ #ifndef HAVE_MORECORE #if ONLY_MSPACES #define HAVE_MORECORE 0 #else /* ONLY_MSPACES */ #define HAVE_MORECORE 1 #endif /* ONLY_MSPACES */ #endif /* HAVE_MORECORE */ #if !HAVE_MORECORE #define MORECORE_CONTIGUOUS 0 #else /* !HAVE_MORECORE */ #define MORECORE_DEFAULT sbrk #ifndef MORECORE_CONTIGUOUS #define MORECORE_CONTIGUOUS 1 #endif /* MORECORE_CONTIGUOUS */ #endif /* HAVE_MORECORE */ #ifndef DEFAULT_GRANULARITY #if (MORECORE_CONTIGUOUS || defined(WIN32)) #define DEFAULT_GRANULARITY (0) /* 0 means to compute in init_mparams */ #else /* MORECORE_CONTIGUOUS */ #define DEFAULT_GRANULARITY ((size_t)64U * (size_t)1024U) #endif /* MORECORE_CONTIGUOUS */ #endif /* DEFAULT_GRANULARITY */ #ifndef DEFAULT_TRIM_THRESHOLD #ifndef MORECORE_CANNOT_TRIM #define DEFAULT_TRIM_THRESHOLD ((size_t)2U * (size_t)1024U * (size_t)1024U) #else /* MORECORE_CANNOT_TRIM */ #define DEFAULT_TRIM_THRESHOLD MAX_SIZE_T #endif /* MORECORE_CANNOT_TRIM */ #endif /* DEFAULT_TRIM_THRESHOLD */ #ifndef DEFAULT_MMAP_THRESHOLD #if HAVE_MMAP /* * The default value in the dlmalloc was set as follows: * * #define DEFAULT_MMAP_THRESHOLD ((size_t)256U * (size_t)1024U) * * Above this threshold the sys_alloc() calls mmap_alloc() to directly mmap the memory. * However, the interaction of this path with the rest of the vpp infra results * in vpp infra considering directly mmap-allocated pieces to not * be part of the heap, with predictable consequence. * * A simple unit-test to show that behavior is to make a small private * heap and repeatedly perform vec_add1() within that heap. * * The issue is because there is no tracking which mmap-allocated chunk * belongs to which heap. * * The temporary approach is to dial up the threshold so that the problematic * code path never gets called. The full fix needs to introduce * introduce the vector of mmap-allocated chunks to mspace, and in general * do some more thorough testing. */ #define DEFAULT_MMAP_THRESHOLD ((size_t)~0ULL) #else /* HAVE_MMAP */ #define DEFAULT_MMAP_THRESHOLD MAX_SIZE_T #endif /* HAVE_MMAP */ #endif /* DEFAULT_MMAP_THRESHOLD */ #ifndef MAX_RELEASE_CHECK_RATE #if HAVE_MMAP #define MAX_RELEASE_CHECK_RATE 4095 #else #define MAX_RELEASE_CHECK_RATE MAX_SIZE_T #endif /* HAVE_MMAP */ #endif /* MAX_RELEASE_CHECK_RATE */ #ifndef USE_BUILTIN_FFS #define USE_BUILTIN_FFS 0 #endif /* USE_BUILTIN_FFS */ #ifndef USE_DEV_RANDOM #define USE_DEV_RANDOM 0 #endif /* USE_DEV_RANDOM */ #ifndef NO_MALLINFO #define NO_MALLINFO 0 #endif /* NO_MALLINFO */ #ifndef MALLINFO_FIELD_TYPE #define MALLINFO_FIELD_TYPE size_t #endif /* MALLINFO_FIELD_TYPE */ #ifndef NO_MALLOC_STATS #define NO_MALLOC_STATS 0 #endif /* NO_MALLOC_STATS */ #ifndef NO_SEGMENT_TRAVERSAL #define NO_SEGMENT_TRAVERSAL 0 #endif /* NO_SEGMENT_TRAVERSAL */ /* mallopt tuning options. SVID/XPG defines four standard parameter numbers for mallopt, normally defined in malloc.h. None of these are used in this malloc, so setting them has no effect. But this malloc does support the following options. */ #define M_TRIM_THRESHOLD (-1) #define M_GRANULARITY (-2) #define M_MMAP_THRESHOLD (-3) /* ------------------------ Mallinfo declarations ------------------------ */ #if !NO_MALLINFO /* This version of malloc supports the standard SVID/XPG mallinfo routine that returns a struct containing usage properties and statistics. It should work on any system that has a /usr/include/malloc.h defining struct mallinfo. The main declaration needed is the mallinfo struct that is returned (by-copy) by mallinfo(). The malloinfo struct contains a bunch of fields that are not even meaningful in this version of malloc. These fields are are instead filled by mallinfo() with other numbers that might be of interest. HAVE_USR_INCLUDE_MALLOC_H should be set if you have a /usr/include/malloc.h file that includes a declaration of struct mallinfo. If so, it is included; else a compliant version is declared below. These must be precisely the same for mallinfo() to work. The original SVID version of this struct, defined on most systems with mallinfo, declares all fields as ints. But some others define as unsigned long. If your system defines the fields using a type of different width than listed here, you MUST #include your system version and #define HAVE_USR_INCLUDE_MALLOC_H. */ /* #define HAVE_USR_INCLUDE_MALLOC_H */ #if 0 // def HAVE_USR_INCLUDE_MALLOC_H #include "/usr/include/malloc.h" #else /* HAVE_USR_INCLUDE_MALLOC_H */ #ifndef STRUCT_MALLINFO_DECLARED /* HP-UX (and others?) redefines mallinfo unless _STRUCT_MALLINFO is defined */ #define _STRUCT_MALLINFO #define STRUCT_MALLINFO_DECLARED 1 struct dlmallinfo { MALLINFO_FIELD_TYPE arena; /* non-mmapped space allocated from system */ MALLINFO_FIELD_TYPE ordblks; /* number of free chunks */ MALLINFO_FIELD_TYPE smblks; /* always 0 */ MALLINFO_FIELD_TYPE hblks; /* always 0 */ MALLINFO_FIELD_TYPE hblkhd; /* space in mmapped regions */ MALLINFO_FIELD_TYPE usmblks; /* maximum total allocated space */ MALLINFO_FIELD_TYPE fsmblks; /* always 0 */ MALLINFO_FIELD_TYPE uordblks; /* total allocated space */ MALLINFO_FIELD_TYPE fordblks; /* total free space */ MALLINFO_FIELD_TYPE keepcost; /* releasable (via malloc_trim) space */ }; #endif /* STRUCT_MALLINFO_DECLARED */ #endif /* HAVE_USR_INCLUDE_MALLOC_H */ #endif /* NO_MALLINFO */ /* Try to persuade compilers to inline. The most critical functions for inlining are defined as macros, so these aren't used for them. */ #ifndef FORCEINLINE #if defined(__GNUC__) #define FORCEINLINE __inline __attribute__ ((always_inline)) #elif defined(_MSC_VER) #define FORCEINLINE __forceinline #endif #endif #ifndef NOINLINE #if defined(__GNUC__) #define NOINLINE __attribute__ ((noinline)) #elif defined(_MSC_VER) #define NOINLINE __declspec(noinline) #else #define NOINLINE #endif #endif #ifdef __cplusplus extern "C" { #ifndef FORCEINLINE #define FORCEINLINE inline #endif #endif /* __cplusplus */ #ifndef FORCEINLINE #define FORCEINLINE #endif #if !ONLY_MSPACES /* ------------------- Declarations of public routines ------------------- */ #ifndef USE_DL_PREFIX #define dlcalloc calloc #define dlfree free #define dlmalloc malloc #define dlmemalign memalign #define dlposix_memalign posix_memalign #define dlrealloc realloc #define dlrealloc_in_place realloc_in_place #define dlvalloc valloc #define dlpvalloc pvalloc // #define dlmallinfo mallinfo #define dlmallopt mallopt #define dlmalloc_trim malloc_trim #define dlmalloc_stats malloc_stats #define dlmalloc_usable_size malloc_usable_size #define dlmalloc_footprint malloc_footprint #define dlmalloc_max_footprint malloc_max_footprint #define dlmalloc_footprint_limit malloc_footprint_limit #define dlmalloc_set_footprint_limit malloc_set_footprint_limit #define dlmalloc_inspect_all malloc_inspect_all #define dlindependent_calloc independent_calloc #define dlindependent_comalloc independent_comalloc #define dlbulk_free bulk_free #endif /* USE_DL_PREFIX */ /* malloc(size_t n) Returns a pointer to a newly allocated chunk of at least n bytes, or null if no space is available, in which case errno is set to ENOMEM on ANSI C systems. If n is zero, malloc returns a minimum-sized chunk. (The minimum size is 16 bytes on most 32bit systems, and 32 bytes on 64bit systems.) Note that size_t is an unsigned type, so calls with arguments that would be negative if signed are interpreted as requests for huge amounts of space, which will often fail. The maximum supported value of n differs across systems, but is in all cases less than the maximum representable value of a size_t. */ DLMALLOC_EXPORT void* dlmalloc(size_t); /* free(void* p) Releases the chunk of memory pointed to by p, that had been previously allocated using malloc or a related routine such as realloc. It has no effect if p is null. If p was not malloced or already freed, free(p) will by default cause the current program to abort. */ DLMALLOC_EXPORT void dlfree(void*); /* calloc(size_t n_elements, size_t element_size); Returns a pointer to n_elements * element_size bytes, with all locations set to zero. */ DLMALLOC_EXPORT void* dlcalloc(size_t, size_t); /* realloc(void* p, size_t n) Returns a pointer to a chunk of size n that contains the same data as does chunk p up to the minimum of (n, p's size) bytes, or null if no space is available. The returned pointer may or may not be the same as p. The algorithm prefers extending p in most cases when possible, otherwise it employs the equivalent of a malloc-copy-free sequence. If p is null, realloc is equivalent to malloc. If space is not available, realloc returns null, errno is set (if on ANSI) and p is NOT freed. if n is for fewer bytes than already held by p, the newly unused space is lopped off and freed if possible. realloc with a size argument of zero (re)allocates a minimum-sized chunk. The old unix realloc convention of allowing the last-free'd chunk to be used as an argument to realloc is not supported. */ DLMALLOC_EXPORT void* dlrealloc(void*, size_t); /* realloc_in_place(void* p, size_t n) Resizes the space allocated for p to size n, only if this can be done without moving p (i.e., only if there is adjacent space available if n is greater than p's current allocated size, or n is less than or equal to p's size). This may be used instead of plain realloc if an alternative allocation strategy is needed upon failure to expand space; for example, reallocation of a buffer that must be memory-aligned or cleared. You can use realloc_in_place to trigger these alternatives only when needed. Returns p if successful; otherwise null. */ DLMALLOC_EXPORT void* dlrealloc_in_place(void*, size_t); /* memalign(size_t alignment, size_t n); Returns a pointer to a newly allocated chunk of n bytes, aligned in accord with the alignment argument. The alignment argument should be a power of two. If the argument is not a power of two, the nearest greater power is used. 8-byte alignment is guaranteed by normal malloc calls, so don't bother calling memalign with an argument of 8 or less. Overreliance on memalign is a sure way to fragment space. */ DLMALLOC_EXPORT void* dlmemalign(size_t, size_t); /* int posix_memalign(void** pp, size_t alignment, size_t n); Allocates a chunk of n bytes, aligned in accord with the alignment argument. Differs from memalign only in that it (1) assigns the allocated memory to *pp rather than returning it, (2) fails and returns EINVAL if the alignment is not a power of two (3) fails and returns ENOMEM if memory cannot be allocated. */ DLMALLOC_EXPORT int dlposix_memalign(void**, size_t, size_t); /* valloc(size_t n); Equivalent to memalign(pagesize, n), where pagesize is the page size of the system. If the pagesize is unknown, 4096 is used. */ DLMALLOC_EXPORT void* dlvalloc(size_t); /* mallopt(int parameter_number, int parameter_value) Sets tunable parameters The format is to provide a (parameter-number, parameter-value) pair. mallopt then sets the corresponding parameter to the argument value if it can (i.e., so long as the value is meaningful), and returns 1 if successful else 0. To workaround the fact that mallopt is specified to use int, not size_t parameters, the value -1 is specially treated as the maximum unsigned size_t value. SVID/XPG/ANSI defines four standard param numbers for mallopt, normally defined in malloc.h. None of these are use in this malloc, so setting them has no effect. But this malloc also supports other options in mallopt. See below for details. Briefly, supported parameters are as follows (listed defaults are for "typical" configurations). Symbol param # default allowed param values M_TRIM_THRESHOLD -1 2*1024*1024 any (-1 disables) M_GRANULARITY -2 page size any power of 2 >= page size M_MMAP_THRESHOLD -3 256*1024 any (or 0 if no MMAP support) */ DLMALLOC_EXPORT int dlmallopt(int, int); /* malloc_footprint(); Returns the number of bytes obtained from the system. The total number of bytes allocated by malloc, realloc etc., is less than this value. Unlike mallinfo, this function returns only a precomputed result, so can be called frequently to monitor memory consumption. Even if locks are otherwise defined, this function does not use them, so results might not be up to date. */ DLMALLOC_EXPORT size_t dlmalloc_footprint(void); /* malloc_max_footprint(); Returns the maximum number of bytes obtained from the system. This value will be greater than current footprint if deallocated space has been reclaimed by the system. The peak number of bytes allocated by malloc, realloc etc., is less than this value. Unlike mallinfo, this function returns only a precomputed result, so can be called frequently to monitor memory consumption. Even if locks are otherwise defined, this function does not use them, so results might not be up to date. */ DLMALLOC_EXPORT size_t dlmalloc_max_footprint(void); /* malloc_footprint_limit(); Returns the number of bytes that the heap is allowed to obtain from the system, returning the last value returned by malloc_set_footprint_limit, or the maximum size_t value if never set. The returned value reflects a permission. There is no guarantee that this number of bytes can actually be obtained from the system. */ DLMALLOC_EXPORT size_t dlmalloc_footprint_limit(); /* malloc_set_footprint_limit(); Sets the maximum number of bytes to obtain from the system, causing failure returns from malloc and related functions upon attempts to exceed this value. The argument value may be subject to page rounding to an enforceable limit; this actual value is returned. Using an argument of the maximum possible size_t effectively disables checks. If the argument is less than or equal to the current malloc_footprint, then all future allocations that require additional system memory will fail. However, invocation cannot retroactively deallocate existing used memory. */ DLMALLOC_EXPORT size_t dlmalloc_set_footprint_limit(size_t bytes); #if MALLOC_INSPECT_ALL /* malloc_inspect_all(void(*handler)(void *start, void *end, size_t used_bytes, void* callback_arg), void* arg); Traverses the heap and calls the given handler for each managed region, skipping all bytes that are (or may be) used for bookkeeping purposes. Traversal does not include include chunks that have been directly memory mapped. Each reported region begins at the start address, and continues up to but not including the end address. The first used_bytes of the region contain allocated data. If used_bytes is zero, the region is unallocated. The handler is invoked with the given callback argument. If locks are defined, they are held during the entire traversal. It is a bad idea to invoke other malloc functions from within the handler. For example, to count the number of in-use chunks with size greater than 1000, you could write: static int count = 0; void count_chunks(void* start, void* end, size_t used, void* arg) { if (used >= 1000) ++count; } then: malloc_inspect_all(count_chunks, NULL); malloc_inspect_all is compiled only if MALLOC_INSPECT_ALL is defined. */ DLMALLOC_EXPORT void dlmalloc_inspect_all(void(*handler)(void*, void *, size_t, void*), void* arg); #endif /* MALLOC_INSPECT_ALL */ #if !NO_MALLINFO /* mallinfo() Returns (by copy) a struct containing various summary statistics: arena: current total non-mmapped bytes allocated from system ordblks: the number of free chunks smblks: always zero. hblks: current number of mmapped regions hblkhd: total bytes held in mmapped regions usmblks: the maximum total allocated space. This will be greater than current total if trimming has occurred. fsmblks: always zero uordblks: current total allocated space (normal or mmapped) fordblks: total free space keepcost: the maximum number of bytes that could ideally be released back to system via malloc_trim. ("ideally" means that it ignores page restrictions etc.) Because these fields are ints, but internal bookkeeping may be kept as longs, the reported values may wrap around zero and thus be inaccurate. */ DLMALLOC_EXPORT struct dlmallinfo dlmallinfo(void); #endif /* NO_MALLINFO */ /* independent_calloc(size_t n_elements, size_t element_size, void* chunks[]); independent_calloc is similar to calloc, but instead of returning a single cleared space, it returns an array of pointers to n_elements independent elements that can hold contents of size elem_size, each of which starts out cleared, and can be independently freed, realloc'ed etc. The elements are guaranteed to be adjacently allocated (this is not guaranteed to occur with multiple callocs or mallocs), which may also improve cache locality in some applications. The "chunks" argument is optional (i.e., may be null, which is probably the most typical usage). If it is null, the returned array is itself dynamically allocated and should also be freed when it is no longer needed. Otherwise, the chunks array must be of at least n_elements in length. It is filled in with the pointers to the chunks. In either case, independent_calloc returns this pointer array, or null if the allocation failed. If n_elements is zero and "chunks" is null, it returns a chunk representing an array with zero elements (which should be freed if not wanted). Each element must be freed when it is no longer needed. This can be done all at once using bulk_free. independent_calloc simplifies and speeds up implementations of many kinds of pools. It may also be useful when constructing large data structures that initially have a fixed number of fixed-sized nodes, but the number is not known at compile time, and some of the nodes may later need to be freed. For example: struct Node { int item; struct Node* next; }; struct Node* build_list() { struct Node** pool; int n = read_number_of_nodes_needed(); if (n <= 0) return 0; pool = (struct Node**)(independent_calloc(n, sizeof(struct Node), 0); if (pool == 0) die(); // organize into a linked list... struct Node* first = pool[0]; for (i = 0; i < n-1; ++i) pool[i]->next = pool[i+1]; free(pool); // Can now free the array (or not, if it is needed later) return first; } */ DLMALLOC_EXPORT void** dlindependent_calloc(size_t, size_t, void**); /* independent_comalloc(size_t n_elements, size_t sizes[], void* chunks[]); independent_comalloc allocates, all at once, a set of n_elements chunks with sizes indicated in the "sizes" array. It returns an array of pointers to these elements, each of which can be independently freed, realloc'ed etc. The elements are guaranteed to be adjacently allocated (this is not guaranteed to occur with multiple callocs or mallocs), which may also improve cache locality in some applications. The "chunks" argument is optional (i.e., may be null). If it is null the returned array is itself dynamically allocated and should also be freed when it is no longer needed. Otherwise, the chunks array must be of at least n_elements in length. It is filled in with the pointers to the chunks. In either case, independent_comalloc returns this pointer array, or null if the allocation failed. If n_elements is zero and chunks is null, it returns a chunk representing an array with zero elements (which should be freed if not wanted). Each element must be freed when it is no longer needed. This can be done all at once using bulk_free. independent_comallac differs from independent_calloc in that each element may have a different size, and also that it does not automatically clear elements. independent_comalloc can be used to speed up allocation in cases where several structs or objects must always be allocated at the same time. For example: struct Head { ... } struct Foot { ... } void send_message(char* msg) { int msglen = strlen(msg); size_t sizes[3] = { sizeof(struct Head), msglen, sizeof(struct Foot) }; void* chunks[3]; if (independent_comalloc(3, sizes, chunks) == 0) die(); struct Head* head = (struct Head*)(chunks[0]); char* body = (char*)(chunks[1]); struct Foot* foot = (struct Foot*)(chunks[2]); // ... } In general though, independent_comalloc is worth using only for larger values of n_elements. For small values, you probably won't detect enough difference from series of malloc calls to bother. Overuse of independent_comalloc can increase overall memory usage, since it cannot reuse existing noncontiguous small chunks that might be available for some of the elements. */ DLMALLOC_EXPORT void** dlindependent_comalloc(size_t, size_t*, void**); /* bulk_free(void* array[], size_t n_elements) Frees and clears (sets to null) each non-null pointer in the given array. This is likely to be faster than freeing them one-by-one. If footers are used, pointers that have been allocated in different mspaces are not freed or cleared, and the count of all such pointers is returned. For large arrays of pointers with poor locality, it may be worthwhile to sort this array before calling bulk_free. */ DLMALLOC_EXPORT size_t dlbulk_free(void**, size_t n_elements); /* pvalloc(size_t n); Equivalent to valloc(minimum-page-that-holds(n)), that is, round up n to nearest pagesize. */ DLMALLOC_EXPORT void* dlpvalloc(size_t); /* malloc_trim(size_t pad); If possible, gives memory back to the system (via negative arguments to sbrk) if there is unused memory at the `high' end of the malloc pool or in unused MMAP segments. You can call this after freeing large blocks of memory to potentially reduce the system-level memory requirements of a program. However, it cannot guarantee to reduce memory. Under some allocation patterns, some large free blocks of memory will be locked between two used chunks, so they cannot be given back to the system. The `pad' argument to malloc_trim represents the amount of free trailing space to leave untrimmed. If this argument is zero, only the minimum amount of memory to maintain internal data structures will be left. Non-zero arguments can be supplied to maintain enough trailing space to service future expected allocations without having to re-obtain memory from the system. Malloc_trim returns 1 if it actually released any memory, else 0. */ DLMALLOC_EXPORT int dlmalloc_trim(size_t); /* malloc_stats(); Prints on stderr the amount of space obtained from the system (both via sbrk and mmap), the maximum amount (which may be more than current if malloc_trim and/or munmap got called), and the current number of bytes allocated via malloc (or realloc, etc) but not yet freed. Note that this is the number of bytes allocated, not the number requested. It will be larger than the number requested because of alignment and bookkeeping overhead. Because it includes alignment wastage as being in use, this figure may be greater than zero even when no user-level chunks are allocated. The reported current and maximum system memory can be inaccurate if a program makes other calls to system memory allocation functions (normally sbrk) outside of malloc. malloc_stats prints only the most commonly interesting statistics. More information can be obtained by calling mallinfo. */ DLMALLOC_EXPORT void dlmalloc_stats(void); /* malloc_usable_size(void* p); Returns the number of bytes you can actually use in an allocated chunk, which may be more than you requested (although often not) due to alignment and minimum size constraints. You can use this many bytes without worrying about overwriting other allocated objects. This is not a particularly great programming practice. malloc_usable_size can be more useful in debugging and assertions, for example: p = malloc(n); assert(malloc_usable_size(p) >= 256); */ size_t dlmalloc_usable_size(void*); #endif /* ONLY_MSPACES */ #if MSPACES /* mspace is an opaque type representing an independent region of space that supports mspace_malloc, etc. */ typedef void* mspace; /* create_mspace creates and returns a new independent space with the given initial capacity, or, if 0, the default granularity size. It returns null if there is no system memory available to create the space. If argument locked is non-zero, the space uses a separate lock to control access. The capacity of the space will grow dynamically as needed to service mspace_malloc requests. You can control the sizes of incremental increases of this space by compiling with a different DEFAULT_GRANULARITY or dynamically setting with mallopt(M_GRANULARITY, value). */ DLMALLOC_EXPORT mspace create_mspace(size_t capacity, int locked); /* destroy_mspace destroys the given space, and attempts to return all of its memory back to the system, returning the total number of bytes freed. After destruction, the results of access to all memory used by the space become undefined. */ DLMALLOC_EXPORT size_t destroy_mspace(mspace msp); /* create_mspace_with_base uses the memory supplied as the initial base of a new mspace. Part (less than 128*sizeof(size_t) bytes) of this space is used for bookkeeping, so the capacity must be at least this large. (Otherwise 0 is returned.) When this initial space is exhausted, additional memory will be obtained from the system. Destroying this space will deallocate all additionally allocated space (if possible) but not the initial base. */ DLMALLOC_EXPORT mspace create_mspace_with_base(void* base, size_t capacity, int locked); /* mspace_track_large_chunks controls whether requests for large chunks are allocated in their own untracked mmapped regions, separate from others in this mspace. By default large chunks are not tracked, which reduces fragmentation. However, such chunks are not necessarily released to the system upon destroy_mspace. Enabling tracking by setting to true may increase fragmentation, but avoids leakage when relying on destroy_mspace to release all memory allocated using this space. The function returns the previous setting. */ DLMALLOC_EXPORT int mspace_track_large_chunks(mspace msp, int enable); /* mspace_malloc behaves as malloc, but operates within the given space. */ DLMALLOC_EXPORT void* mspace_malloc(mspace msp, size_t bytes); /* mspace_free behaves as free, but operates within the given space. If compiled with FOOTERS==1, mspace_free is not actually needed. free may be called instead of mspace_free because freed chunks from any space are handled by their originating spaces. */ DLMALLOC_EXPORT void mspace_free(mspace msp, void* mem); /* mspace_realloc behaves as realloc, but operates within the given space. If compiled with FOOTERS==1, mspace_realloc is not actually needed. realloc may be called instead of mspace_realloc because realloced chunks from any space are handled by their originating spaces. */ DLMALLOC_EXPORT void* mspace_realloc(mspace msp, void* mem, size_t newsize); /* mspace_calloc behaves as calloc, but operates within the given space. */ DLMALLOC_EXPORT void* mspace_calloc(mspace msp, size_t n_elements, size_t elem_size); /* mspace_memalign behaves as memalign, but operates within the given space. */ DLMALLOC_EXPORT void* mspace_memalign(mspace msp, size_t alignment, size_t bytes); /* mspace_independent_calloc behaves as independent_calloc, but operates within the given space. */ DLMALLOC_EXPORT void** mspace_independent_calloc(mspace msp, size_t n_elements, size_t elem_size, void* chunks[]); /* mspace_independent_comalloc behaves as independent_comalloc, but operates within the given space. */ DLMALLOC_EXPORT void** mspace_independent_comalloc(mspace msp, size_t n_elements, size_t sizes[], void* chunks[]); /* mspace_footprint() returns the number of bytes obtained from the system for this space. */ DLMALLOC_EXPORT size_t mspace_footprint(mspace msp); /* mspace_max_footprint() returns the peak number of bytes obtained from the system for this space. */ DLMALLOC_EXPORT size_t mspace_max_footprint(mspace msp); #if !NO_MALLINFO /* mspace_mallinfo behaves as mallinfo, but reports properties of the given space. */ DLMALLOC_EXPORT struct dlmallinfo mspace_mallinfo(mspace msp); #endif /* NO_MALLINFO */ /* malloc_usable_size(void* p) behaves the same as malloc_usable_size; */ DLMALLOC_EXPORT size_t mspace_usable_size(const void* mem); /* mspace_malloc_stats behaves as malloc_stats, but reports properties of the given space. */ DLMALLOC_EXPORT void mspace_malloc_stats(mspace msp); /* mspace_trim behaves as malloc_trim, but operates within the given space. */ DLMALLOC_EXPORT int mspace_trim(mspace msp, size_t pad); /* An alias for mallopt. */ DLMALLOC_EXPORT int mspace_mallopt(int, int); DLMALLOC_EXPORT void* mspace_get_aligned (mspace msp, unsigned long n_user_data_bytes, unsigned long align, unsigned long align_offset); DLMALLOC_EXPORT int mspace_is_heap_object (mspace msp, void *p); DLMALLOC_EXPORT void mspace_get_address_and_size (mspace msp, char **addrp, size_t *sizep); DLMALLOC_EXPORT void mspace_put (mspace msp, void *p); DLMALLOC_EXPORT void mspace_put_no_offset (mspace msp, void *p); DLMALLOC_EXPORT size_t mspace_usable_size_with_delta (const void *p); DLMALLOC_EXPORT void mspace_disable_expand (mspace msp); DLMALLOC_EXPORT void *mspace_least_addr (mspace msp); DLMALLOC_EXPORT void mheap_get_trace (uword offset, uword size); DLMALLOC_EXPORT void mheap_put_trace (uword offset, uword size); DLMALLOC_EXPORT int mspace_enable_disable_trace (mspace msp, int enable); DLMALLOC_EXPORT int mspace_is_traced (mspace msp); #endif /* MSPACES */ #ifdef __cplusplus } /* end of extern "C" */ #endif /* __cplusplus */ /* ======================================================================== To make a fully customizable malloc.h header file, cut everything above this line, put into file malloc.h, edit to suit, and #include it on the next line, as well as in programs that use this malloc. ======================================================================== */