summaryrefslogtreecommitdiffstats
path: root/doc/guides/nics/ixgbe.rst
diff options
context:
space:
mode:
Diffstat (limited to 'doc/guides/nics/ixgbe.rst')
-rw-r--r--doc/guides/nics/ixgbe.rst55
1 files changed, 26 insertions, 29 deletions
diff --git a/doc/guides/nics/ixgbe.rst b/doc/guides/nics/ixgbe.rst
index 3b6851b6..696ff693 100644
--- a/doc/guides/nics/ixgbe.rst
+++ b/doc/guides/nics/ixgbe.rst
@@ -95,9 +95,6 @@ Other features are supported using optional MACRO configuration. They include:
* HW extend dual VLAN
-* Enabled by RX_OLFLAGS (RTE_IXGBE_RX_OLFLAGS_ENABLE=y)
-
-
To guarantee the constraint, configuration flags in dev_conf.rxmode will be checked:
* hw_vlan_strip
@@ -129,7 +126,7 @@ The tx_rs_thresh value must be greater than or equal to RTE_PMD_IXGBE_TX_MAX_BUR
but less or equal to RTE_IXGBE_TX_MAX_FREE_BUF_SZ.
Consequently, by default the tx_rs_thresh value is in the range 32 to 64.
-Feature not Supported by RX Vector PMD
+Feature not Supported by TX Vector PMD
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
TX vPMD only works when txq_flags is set to IXGBE_SIMPLE_FLAGS.
@@ -148,45 +145,33 @@ The following MACROs are used for these three features:
* ETH_TXQ_FLAGS_NOXSUMTCP
Application Programming Interface
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+---------------------------------
In DPDK release v16.11 an API for ixgbe specific functions has been added to the ixgbe PMD.
The declarations for the API functions are in the header ``rte_pmd_ixgbe.h``.
Sample Application Notes
-~~~~~~~~~~~~~~~~~~~~~~~~
-
-testpmd
-^^^^^^^
-
-By default, using CONFIG_RTE_IXGBE_RX_OLFLAGS_ENABLE=y:
-
-.. code-block:: console
-
- ./x86_64-native-linuxapp-gcc/app/testpmd -c 300 -n 4 -- -i --burst=32 --rxfreet=32 --mbcache=250 --txpt=32 --rxht=8 --rxwt=0 --txfreet=32 --txrst=32 --txqflags=0xf01
-
-When CONFIG_RTE_IXGBE_RX_OLFLAGS_ENABLE=n, better performance can be achieved:
-
-.. code-block:: console
-
- ./x86_64-native-linuxapp-gcc/app/testpmd -c 300 -n 4 -- -i --burst=32 --rxfreet=32 --mbcache=250 --txpt=32 --rxht=8 --rxwt=0 --txfreet=32 --txrst=32 --txqflags=0xf01 --disable-hw-vlan
+------------------------
l3fwd
-^^^^^
+~~~~~
When running l3fwd with vPMD, there is one thing to note.
In the configuration, ensure that port_conf.rxmode.hw_ip_checksum=0.
Otherwise, by default, RX vPMD is disabled.
load_balancer
-^^^^^^^^^^^^^
+~~~~~~~~~~~~~
As in the case of l3fwd, set configure port_conf.rxmode.hw_ip_checksum=0 to enable vPMD.
In addition, for improved performance, use -bsz "(32,32),(64,64),(32,32)" in load_balancer to avoid using the default burst size of 144.
+Limitations or Known issues
+---------------------------
+
Malicious Driver Detection not Supported
-----------------------------------------
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The Intel x550 series NICs support a feature called MDD (Malicious
Driver Detection) which checks the behavior of the VF driver.
@@ -200,14 +185,17 @@ There's significant performance impact to support MDD. DPDK should check if
the advanced context descriptor should be set and set it. And DPDK has to ask
the info about the header length from the upper layer, because parsing the
packet itself is not acceptable. So, it's too expensive to support MDD.
-When using kernel PF + DPDK VF on x550, please make sure using the kernel
-driver that disables MDD or can disable MDD. (Some kernel driver can use
-this CLI 'insmod ixgbe.ko MDD=0,0' to disable MDD. Some kernel driver disables
-it by default.)
+When using kernel PF + DPDK VF on x550, please make sure to use a kernel
+PF driver that disables MDD or can disable MDD.
+
+Some kernel drivers already disable MDD by default while some kernels can use
+the command ``insmod ixgbe.ko MDD=0,0`` to disable MDD. Each "0" in the
+command refers to a port. For example, if there are 6 ixgbe ports, the command
+should be changed to ``insmod ixgbe.ko MDD=0,0,0,0,0,0``.
Statistics
-----------
+~~~~~~~~~~
The statistics of ixgbe hardware must be polled regularly in order for it to
remain consistent. Running a DPDK application without polling the statistics will
@@ -230,6 +218,15 @@ be calculated as follows:
In order to ensure valid results, it is recommended to poll every 4 minutes.
+MTU setting
+~~~~~~~~~~~
+
+Although the user can set the MTU separately on PF and VF ports, the ixgbe NIC
+only supports one global MTU per physical port.
+So when the user sets different MTUs on PF and VF ports in one physical port,
+the real MTU for all these PF and VF ports is the largest value set.
+This behavior is based on the kernel driver behavior.
+
Supported Chipsets and NICs
---------------------------