diff options
Diffstat (limited to 'doc/guides/prog_guide/link_bonding_poll_mode_drv_lib.rst')
| -rw-r--r-- | doc/guides/prog_guide/link_bonding_poll_mode_drv_lib.rst | 14 |
1 files changed, 7 insertions, 7 deletions
diff --git a/doc/guides/prog_guide/link_bonding_poll_mode_drv_lib.rst b/doc/guides/prog_guide/link_bonding_poll_mode_drv_lib.rst index 01ddcb91..65813c9e 100644 --- a/doc/guides/prog_guide/link_bonding_poll_mode_drv_lib.rst +++ b/doc/guides/prog_guide/link_bonding_poll_mode_drv_lib.rst @@ -356,7 +356,7 @@ Using Link Bonding Devices from the EAL Command Line Link bonding devices can be created at application startup time using the ``--vdev`` EAL command line option. The device name must start with the -eth_bond prefix followed by numbers or letters. The name must be unique for +net_bond prefix followed by numbers or letters. The name must be unique for each device. Each device can have multiple options arranged in a comma separated list. Multiple devices definitions can be arranged by calling the ``--vdev`` option multiple times. @@ -365,7 +365,7 @@ Device names and bonding options must be separated by commas as shown below: .. code-block:: console - $RTE_TARGET/app/testpmd -c f -n 4 --vdev 'eth_bond0,bond_opt0=..,bond opt1=..'--vdev 'eth_bond1,bond _opt0=..,bond_opt1=..' + $RTE_TARGET/app/testpmd -c f -n 4 --vdev 'net_bond0,bond_opt0=..,bond opt1=..'--vdev 'net_bond1,bond _opt0=..,bond_opt1=..' Link Bonding EAL Options ^^^^^^^^^^^^^^^^^^^^^^^^ @@ -373,7 +373,7 @@ Link Bonding EAL Options There are multiple ways of definitions that can be assessed and combined as long as the following two rules are respected: -* A unique device name, in the format of eth_bondX is provided, +* A unique device name, in the format of net_bondX is provided, where X can be any combination of numbers and/or letters, and the name is no greater than 32 characters long. @@ -465,22 +465,22 @@ Create a bonded device in round robin mode with two slaves specified by their PC .. code-block:: console - $RTE_TARGET/app/testpmd -c '0xf' -n 4 --vdev 'eth_bond0,mode=0, slave=0000:00a:00.01,slave=0000:004:00.00' -- --port-topology=chained + $RTE_TARGET/app/testpmd -c '0xf' -n 4 --vdev 'net_bond0,mode=0, slave=0000:00a:00.01,slave=0000:004:00.00' -- --port-topology=chained Create a bonded device in round robin mode with two slaves specified by their PCI address and an overriding MAC address: .. code-block:: console - $RTE_TARGET/app/testpmd -c '0xf' -n 4 --vdev 'eth_bond0,mode=0, slave=0000:00a:00.01,slave=0000:004:00.00,mac=00:1e:67:1d:fd:1d' -- --port-topology=chained + $RTE_TARGET/app/testpmd -c '0xf' -n 4 --vdev 'net_bond0,mode=0, slave=0000:00a:00.01,slave=0000:004:00.00,mac=00:1e:67:1d:fd:1d' -- --port-topology=chained Create a bonded device in active backup mode with two slaves specified, and a primary slave specified by their PCI addresses: .. code-block:: console - $RTE_TARGET/app/testpmd -c '0xf' -n 4 --vdev 'eth_bond0,mode=1, slave=0000:00a:00.01,slave=0000:004:00.00,primary=0000:00a:00.01' -- --port-topology=chained + $RTE_TARGET/app/testpmd -c '0xf' -n 4 --vdev 'net_bond0,mode=1, slave=0000:00a:00.01,slave=0000:004:00.00,primary=0000:00a:00.01' -- --port-topology=chained Create a bonded device in balance mode with two slaves specified by their PCI addresses, and a transmission policy of layer 3 + 4 forwarding: .. code-block:: console - $RTE_TARGET/app/testpmd -c '0xf' -n 4 --vdev 'eth_bond0,mode=2, slave=0000:00a:00.01,slave=0000:004:00.00,xmit_policy=l34' -- --port-topology=chained + $RTE_TARGET/app/testpmd -c '0xf' -n 4 --vdev 'net_bond0,mode=2, slave=0000:00a:00.01,slave=0000:004:00.00,xmit_policy=l34' -- --port-topology=chained |