summaryrefslogtreecommitdiffstats
path: root/doc/guides/testpmd_app_ug/testpmd_funcs.rst
diff options
context:
space:
mode:
Diffstat (limited to 'doc/guides/testpmd_app_ug/testpmd_funcs.rst')
-rw-r--r--doc/guides/testpmd_app_ug/testpmd_funcs.rst68
1 files changed, 50 insertions, 18 deletions
diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
index aed5e477..30e410dd 100644
--- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
+++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
@@ -98,9 +98,11 @@ Start packet forwarding with current configuration::
start tx_first
~~~~~~~~~~~~~~
-Start packet forwarding with current configuration after sending one burst of packets::
+Start packet forwarding with current configuration after sending specified number of bursts of packets::
- testpmd> start tx_first
+ testpmd> start tx_first (""|burst_num)
+
+The default burst number is 1 when ``burst_num`` not presented.
stop
~~~~
@@ -177,6 +179,10 @@ For example:
ipv6-sctp
ipv6-other
l2_payload
+ port
+ vxlan
+ geneve
+ nvgre
show port rss reta
~~~~~~~~~~~~~~~~~~
@@ -249,8 +255,10 @@ set fwd
Set the packet forwarding mode::
- testpmd> set fwd (io|mac|mac_retry|macswap|flowgen| \
- rxonly|txonly|csum|icmpecho)
+ testpmd> set fwd (io|mac|macswap|flowgen| \
+ rxonly|txonly|csum|icmpecho) (""|retry)
+
+``retry`` can be specified for forwarding engines except ``rx_only``.
The available information categories are:
@@ -260,8 +268,6 @@ The available information categories are:
* ``mac``: Changes the source and the destination Ethernet addresses of packets before forwarding them.
-* ``mac_retry``: Same as "mac" forwarding mode, but includes retries if the destination queue is full.
-
* ``macswap``: MAC swap forwarding mode.
Swaps the source and the destination Ethernet addresses of packets before forwarding them.
@@ -392,9 +398,9 @@ Set number of packets per burst::
This is equivalent to the ``--burst command-line`` option.
-In ``mac_retry`` forwarding mode, the transmit delay time and number of retries can also be set::
+When retry is enabled, the transmit delay time and number of retries can also be set::
- testpmd> set burst tx delay (micrseconds) retry (num)
+ testpmd> set burst tx delay (microseconds) retry (num)
set txpkts
~~~~~~~~~~
@@ -980,7 +986,9 @@ The following sections show functions for configuring ports.
port attach
~~~~~~~~~~~
-Attach a port specified by pci address or virtual device args.
+Attach a port specified by pci address or virtual device args::
+
+ testpmd> port attach (identifier)
To attach a new pci device, the device should be recognized by kernel first.
Then it should be moved under DPDK management.
@@ -1014,8 +1022,6 @@ For example, to move a pci device using ixgbe under DPDK management:
To attach a port created by virtual device, above steps are not needed.
-port attach (identifier)
-
For example, to attach a port whose pci address is 0000:0a:00.0.
.. code-block:: console
@@ -1061,16 +1067,19 @@ the mode and slave parameters must be given.
port detach
~~~~~~~~~~~
-Detach a specific port.
-
-Before detaching a port, the port should be closed::
+Detach a specific port::
testpmd> port detach (port_id)
+Before detaching a port, the port should be stopped and closed.
+
For example, to detach a pci device port 0.
.. code-block:: console
+ testpmd> port stop 0
+ Stopping ports...
+ Done
testpmd> port close 0
Closing ports...
Done
@@ -1088,6 +1097,9 @@ For example, to detach a virtual device port 0.
.. code-block:: console
+ testpmd> port stop 0
+ Stopping ports...
+ Done
testpmd> port close 0
Closing ports...
Done
@@ -1187,6 +1199,26 @@ CRC stripping is off by default.
The ``on`` option is equivalent to the ``--crc-strip`` command-line option.
+port config - scatter
+~~~~~~~~~~~~~~~~~~~~~~~
+
+Set RX scatter mode on or off for all ports::
+
+ testpmd> port config all scatter (on|off)
+
+RX scatter mode is off by default.
+
+The ``on`` option is equivalent to the ``--enable-scatter`` command-line option.
+
+port config - TX queue flags
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set a hexadecimal bitmap of TX queue flags for all ports::
+
+ testpmd> port config all txqflags value
+
+This command is equivalent to the ``--txqflags`` command-line option.
+
port config - RX Checksum
~~~~~~~~~~~~~~~~~~~~~~~~~
@@ -1258,7 +1290,7 @@ port config - RSS
Set the RSS (Receive Side Scaling) mode on or off::
- testpmd> port config all rss (all|ip|tcp|udp|sctp|ether|none)
+ testpmd> port config all rss (all|ip|tcp|udp|sctp|ether|port|vxlan|geneve|nvgre|none)
RSS is on by default.
@@ -1782,13 +1814,13 @@ Different NICs may have different capabilities, command show port fdir (port_id)
For example, to add an ipv4-udp flow type filter::
- testpmd> flow_director_filter 0 add flow ipv4-udp src 2.2.2.3 32 \
+ testpmd> flow_director_filter 0 mode IP add flow ipv4-udp src 2.2.2.3 32 \
dst 2.2.2.5 33 tos 2 ttl 40 vlan 0x1 flexbytes (0x88,0x48) \
fwd pf queue 1 fd_id 1
For example, add an ipv4-other flow type filter::
- testpmd> flow_director_filter 0 add flow ipv4-other src 2.2.2.3 \
+ testpmd> flow_director_filter 0 mode IP add flow ipv4-other src 2.2.2.3 \
dst 2.2.2.5 tos 2 proto 20 ttl 40 vlan 0x1 \
flexbytes (0x88,0x48) fwd pf queue 1 fd_id 1
@@ -1821,7 +1853,7 @@ Set flow director's input masks::
Example, to set flow director mask on port 0::
- testpmd> flow_director_mask 0 vlan 0xefff \
+ testpmd> flow_director_mask 0 mode IP vlan 0xefff \
src_mask 255.255.255.255 \
FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 0xFFFF \
dst_mask 255.255.255.255 \