diff options
Diffstat (limited to 'drivers/net/bnxt/hsi_struct_def_dpdk.h')
| -rw-r--r-- | drivers/net/bnxt/hsi_struct_def_dpdk.h | 5799 |
1 files changed, 5799 insertions, 0 deletions
diff --git a/drivers/net/bnxt/hsi_struct_def_dpdk.h b/drivers/net/bnxt/hsi_struct_def_dpdk.h new file mode 100644 index 00000000..f2db3eaf --- /dev/null +++ b/drivers/net/bnxt/hsi_struct_def_dpdk.h @@ -0,0 +1,5799 @@ +/*- + * BSD LICENSE + * + * Copyright(c) Broadcom Limited. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +#ifndef _HSI_STRUCT_DEF_EXTERNAL_H_ +#define _HSI_STRUCT_DEF_EXTERNAL_H_ + +/* + * per-context HW statistics -- chip view + */ + +struct ctx_hw_stats64 { + uint64_t rx_ucast_pkts; + uint64_t rx_mcast_pkts; + uint64_t rx_bcast_pkts; + uint64_t rx_drop_pkts; + uint64_t rx_err_pkts; + uint64_t rx_ucast_bytes; + uint64_t rx_mcast_bytes; + uint64_t rx_bcast_bytes; + + uint64_t tx_ucast_pkts; + uint64_t tx_mcast_pkts; + uint64_t tx_bcast_pkts; + uint64_t tx_drop_pkts; + uint64_t tx_err_pkts; + uint64_t tx_ucast_bytes; + uint64_t tx_mcast_bytes; + uint64_t tx_bcast_bytes; + + uint64_t tpa_pkts; + uint64_t tpa_bytes; + uint64_t tpa_events; + uint64_t tpa_aborts; +} ctx_hw_stats64_t; + +/* HW Resource Manager Specification 1.2.0 */ +#define HWRM_VERSION_MAJOR 1 +#define HWRM_VERSION_MINOR 2 +#define HWRM_VERSION_UPDATE 0 + +/* + * Following is the signature for HWRM message field that indicates not + * applicable (All F's). Need to cast it the size of the field if needed. + */ +#define HWRM_NA_SIGNATURE ((uint32_t)(-1)) +#define HWRM_MAX_REQ_LEN (128) /* hwrm_func_buf_rgtr */ +#define HWRM_MAX_RESP_LEN (176) /* hwrm_func_qstats */ +#define HW_HASH_INDEX_SIZE 0x80 /* 7 bit indirection table index. */ +#define HW_HASH_KEY_SIZE 40 +#define HWRM_RESP_VALID_KEY 1 /* valid key for HWRM response */ + +/* + * Request types + */ +#define HWRM_VER_GET (UINT32_C(0x0)) +#define HWRM_FUNC_RESET (UINT32_C(0x11)) +#define HWRM_FUNC_QCAPS (UINT32_C(0x15)) +#define HWRM_FUNC_DRV_UNRGTR (UINT32_C(0x1a)) +#define HWRM_FUNC_DRV_RGTR (UINT32_C(0x1d)) +#define HWRM_PORT_PHY_CFG (UINT32_C(0x20)) +#define HWRM_PORT_PHY_QCFG (UINT32_C(0x27)) +#define HWRM_QUEUE_QPORTCFG (UINT32_C(0x30)) +#define HWRM_VNIC_ALLOC (UINT32_C(0x40)) +#define HWRM_VNIC_FREE (UINT32_C(0x41)) +#define HWRM_VNIC_CFG (UINT32_C(0x42)) +#define HWRM_VNIC_RSS_CFG (UINT32_C(0x46)) +#define HWRM_RING_ALLOC (UINT32_C(0x50)) +#define HWRM_RING_FREE (UINT32_C(0x51)) +#define HWRM_RING_GRP_ALLOC (UINT32_C(0x60)) +#define HWRM_RING_GRP_FREE (UINT32_C(0x61)) +#define HWRM_VNIC_RSS_COS_LB_CTX_ALLOC (UINT32_C(0x70)) +#define HWRM_VNIC_RSS_COS_LB_CTX_FREE (UINT32_C(0x71)) +#define HWRM_CFA_L2_FILTER_ALLOC (UINT32_C(0x90)) +#define HWRM_CFA_L2_FILTER_FREE (UINT32_C(0x91)) +#define HWRM_CFA_L2_FILTER_CFG (UINT32_C(0x92)) +#define HWRM_CFA_L2_SET_RX_MASK (UINT32_C(0x93)) +#define HWRM_STAT_CTX_ALLOC (UINT32_C(0xb0)) +#define HWRM_STAT_CTX_FREE (UINT32_C(0xb1)) +#define HWRM_STAT_CTX_CLR_STATS (UINT32_C(0xb3)) +#define HWRM_EXEC_FWD_RESP (UINT32_C(0xd0)) + +/* Return Codes */ +#define HWRM_ERR_CODE_INVALID_PARAMS (UINT32_C(0x2)) +#define HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED (UINT32_C(0x3)) + +/* Short TX BD (16 bytes) */ +struct tx_bd_short { + /* + * All bits in this field must be valid on the first BD of a packet. + * Only the packet_end bit must be valid for the remaining BDs of a + * packet. + */ + /* This value identifies the type of buffer descriptor. */ + #define TX_BD_SHORT_TYPE_MASK UINT32_C(0x3f) + #define TX_BD_SHORT_TYPE_SFT 0 + /* + * Indicates that this BD is 16B long and is used for normal L2 + * packet transmission. + */ + #define TX_BD_SHORT_TYPE_TX_BD_SHORT (UINT32_C(0x0) << 0) + /* + * If set to 1, the packet ends with the data in the buffer pointed to + * by this descriptor. This flag must be valid on every BD. + */ + #define TX_BD_SHORT_FLAGS_PACKET_END UINT32_C(0x40) + /* + * If set to 1, the device will not generate a completion for this + * transmit packet unless there is an error in it's processing. If this + * bit is set to 0, then the packet will be completed normally. This bit + * must be valid only on the first BD of a packet. + */ + #define TX_BD_SHORT_FLAGS_NO_CMPL UINT32_C(0x80) + /* + * This value indicates how many 16B BD locations are consumed in the + * ring by this packet. A value of 1 indicates that this BD is the only + * BD (and that the it is a short BD). A value of 3 indicates either 3 + * short BDs or 1 long BD and one short BD in the packet. A value of 0 + * indicates that there are 32 BD locations in the packet (the maximum). + * This field is valid only on the first BD of a packet. + */ + #define TX_BD_SHORT_FLAGS_BD_CNT_MASK UINT32_C(0x1f00) + #define TX_BD_SHORT_FLAGS_BD_CNT_SFT 8 + /* + * This value is a hint for the length of the entire packet. It is used + * by the chip to optimize internal processing. The packet will be + * dropped if the hint is too short. This field is valid only on the + * first BD of a packet. + */ + #define TX_BD_SHORT_FLAGS_LHINT_MASK UINT32_C(0x6000) + #define TX_BD_SHORT_FLAGS_LHINT_SFT 13 + /* indicates packet length < 512B */ + #define TX_BD_SHORT_FLAGS_LHINT_LT512 (UINT32_C(0x0) << 13) + /* indicates 512 <= packet length < 1KB */ + #define TX_BD_SHORT_FLAGS_LHINT_LT1K (UINT32_C(0x1) << 13) + /* indicates 1KB <= packet length < 2KB */ + #define TX_BD_SHORT_FLAGS_LHINT_LT2K (UINT32_C(0x2) << 13) + /* indicates packet length >= 2KB */ + #define TX_BD_SHORT_FLAGS_LHINT_GTE2K (UINT32_C(0x3) << 13) + #define TX_BD_SHORT_FLAGS_LHINT_LAST TX_BD_SHORT_FLAGS_LHINT_GTE2K + /* + * If set to 1, the device immediately updates the Send Consumer Index + * after the buffer associated with this descriptor has been transferred + * via DMA to NIC memory from host memory. An interrupt may or may not + * be generated according to the state of the interrupt avoidance + * mechanisms. If this bit is set to 0, then the Consumer Index is only + * updated as soon as one of the host interrupt coalescing conditions + * has been met. This bit must be valid on the first BD of a packet. + */ + #define TX_BD_SHORT_FLAGS_COAL_NOW UINT32_C(0x8000) + /* + * All bits in this field must be valid on the first BD of a packet. + * Only the packet_end bit must be valid for the remaining BDs of a + * packet. + */ + #define TX_BD_SHORT_FLAGS_MASK UINT32_C(0xffc0) + #define TX_BD_SHORT_FLAGS_SFT 6 + uint16_t flags_type; + + /* + * This is the length of the host physical buffer this BD describes in + * bytes. This field must be valid on all BDs of a packet. + */ + uint16_t len; + /* + * The opaque data field is pass through to the completion and can be + * used for any data that the driver wants to associate with the + * transmit BD. This field must be valid on the first BD of a packet. + */ + uint32_t opaque; + + /* + * This is the host physical address for the portion of the packet + * described by this TX BD. This value must be valid on all BDs of a + * packet. + */ + uint64_t addr; +} __attribute__((packed)); + +/* Long TX BD (32 bytes split to 2 16-byte struct) */ +struct tx_bd_long { + /* + * All bits in this field must be valid on the first BD of a packet. + * Only the packet_end bit must be valid for the remaining BDs of a + * packet. + */ + /* This value identifies the type of buffer descriptor. */ + #define TX_BD_LONG_TYPE_MASK UINT32_C(0x3f) + #define TX_BD_LONG_TYPE_SFT 0 + /* + * Indicates that this BD is 32B long and is used for normal L2 + * packet transmission. + */ + #define TX_BD_LONG_TYPE_TX_BD_LONG (UINT32_C(0x10) << 0) + /* + * If set to 1, the packet ends with the data in the buffer pointed to + * by this descriptor. This flag must be valid on every BD. + */ + #define TX_BD_LONG_FLAGS_PACKET_END UINT32_C(0x40) + /* + * If set to 1, the device will not generate a completion for this + * transmit packet unless there is an error in it's processing. If this + * bit is set to 0, then the packet will be completed normally. This bit + * must be valid only on the first BD of a packet. + */ + #define TX_BD_LONG_FLAGS_NO_CMPL UINT32_C(0x80) + /* + * This value indicates how many 16B BD locations are consumed in the + * ring by this packet. A value of 1 indicates that this BD is the only + * BD (and that the it is a short BD). A value of 3 indicates either 3 + * short BDs or 1 long BD and one short BD in the packet. A value of 0 + * indicates that there are 32 BD locations in the packet (the maximum). + * This field is valid only on the first BD of a packet. + */ + #define TX_BD_LONG_FLAGS_BD_CNT_MASK UINT32_C(0x1f00) + #define TX_BD_LONG_FLAGS_BD_CNT_SFT 8 + /* + * This value is a hint for the length of the entire packet. It is used + * by the chip to optimize internal processing. The packet will be + * dropped if the hint is too short. This field is valid only on the + * first BD of a packet. + */ + #define TX_BD_LONG_FLAGS_LHINT_MASK UINT32_C(0x6000) + #define TX_BD_LONG_FLAGS_LHINT_SFT 13 + /* indicates packet length < 512B */ + #define TX_BD_LONG_FLAGS_LHINT_LT512 (UINT32_C(0x0) << 13) + /* indicates 512 <= packet length < 1KB */ + #define TX_BD_LONG_FLAGS_LHINT_LT1K (UINT32_C(0x1) << 13) + /* indicates 1KB <= packet length < 2KB */ + #define TX_BD_LONG_FLAGS_LHINT_LT2K (UINT32_C(0x2) << 13) + /* indicates packet length >= 2KB */ + #define TX_BD_LONG_FLAGS_LHINT_GTE2K (UINT32_C(0x3) << 13) + #define TX_BD_LONG_FLAGS_LHINT_LAST TX_BD_LONG_FLAGS_LHINT_GTE2K + /* + * If set to 1, the device immediately updates the Send Consumer Index + * after the buffer associated with this descriptor has been transferred + * via DMA to NIC memory from host memory. An interrupt may or may not + * be generated according to the state of the interrupt avoidance + * mechanisms. If this bit is set to 0, then the Consumer Index is only + * updated as soon as one of the host interrupt coalescing conditions + * has been met. This bit must be valid on the first BD of a packet. + */ + #define TX_BD_LONG_FLAGS_COAL_NOW UINT32_C(0x8000) + /* + * All bits in this field must be valid on the first BD of a packet. + * Only the packet_end bit must be valid for the remaining BDs of a + * packet. + */ + #define TX_BD_LONG_FLAGS_MASK UINT32_C(0xffc0) + #define TX_BD_LONG_FLAGS_SFT 6 + uint16_t flags_type; + + /* + * This is the length of the host physical buffer this BD describes in + * bytes. This field must be valid on all BDs of a packet. + */ + uint16_t len; + + /* + * The opaque data field is pass through to the completion and can be + * used for any data that the driver wants to associate with the + * transmit BD. This field must be valid on the first BD of a packet. + */ + uint32_t opaque; + + /* + * This is the host physical address for the portion of the packet + * described by this TX BD. This value must be valid on all BDs of a + * packet. + */ + uint64_t addr; +} __attribute__((packed)); + +/* last 16 bytes of Long TX BD */ + +struct tx_bd_long_hi { + /* + * All bits in this field must be valid on the first BD of a packet. + * Their value on other BDs of the packet will be ignored. + */ + /* + * If set to 1, the controller replaces the TCP/UPD checksum fields of + * normal TCP/UPD checksum, or the inner TCP/UDP checksum field of the + * encapsulated TCP/UDP packets with the hardware calculated TCP/UDP + * checksum for the packet associated with this descriptor. This bit + * must be valid on the first BD of a packet. + */ + #define TX_BD_LONG_LFLAGS_TCP_UDP_CHKSUM UINT32_C(0x1) + /* + * If set to 1, the controller replaces the IP checksum of the normal + * packets, or the inner IP checksum of the encapsulated packets with + * the hardware calculated IP checksum for the packet associated with + * this descriptor. This bit must be valid on the first BD of a packet. + */ + #define TX_BD_LONG_LFLAGS_IP_CHKSUM UINT32_C(0x2) + /* + * If set to 1, the controller will not append an Ethernet CRC to the + * end of the frame. This bit must be valid on the first BD of a packet. + * Packet must be 64B or longer when this flag is set. It is not useful + * to use this bit with any form of TX offload such as CSO or LSO. The + * intent is that the packet from the host already has a valid Ethernet + * CRC on the packet. + */ + #define TX_BD_LONG_LFLAGS_NOCRC UINT32_C(0x4) + /* + * If set to 1, the device will record the time at which the packet was + * actually transmitted at the TX MAC. This bit must be valid on the + * first BD of a packet. + */ + #define TX_BD_LONG_LFLAGS_STAMP UINT32_C(0x8) + /* + * If set to 1, The controller replaces the tunnel IP checksum field + * with hardware calculated IP checksum for the IP header of the packet + * associated with this descriptor. In case of VXLAN, the controller + * also replaces the outer header UDP checksum with hardware calculated + * UDP checksum for the packet associated with this descriptor. + */ + #define TX_BD_LONG_LFLAGS_T_IP_CHKSUM UINT32_C(0x10) + /* + * If set to 1, the device will treat this packet with LSO(Large Send + * Offload) processing for both normal or encapsulated packets, which is + * a form of TCP segmentation. When this bit is 1, the hdr_size and mss + * fields must be valid. The driver doesn't need to set t_ip_chksum, + * ip_chksum, and tcp_udp_chksum flags since the controller will replace + * the appropriate checksum fields for segmented packets. When this bit + * is 1, the hdr_size and mss fields must be valid. + */ + #define TX_BD_LONG_LFLAGS_LSO UINT32_C(0x20) + /* + * If set to zero when LSO is '1', then the IPID will be treated as a + * 16b number and will be wrapped if it exceeds a value of 0xffff. If + * set to one when LSO is '1', then the IPID will be treated as a 15b + * number and will be wrapped if it exceeds a value 0f 0x7fff. + */ + #define TX_BD_LONG_LFLAGS_IPID_FMT UINT32_C(0x40) + /* + * If set to zero when LSO is '1', then the IPID of the tunnel IP header + * will not be modified during LSO operations. If set to one when LSO is + * '1', then the IPID of the tunnel IP header will be incremented for + * each subsequent segment of an LSO operation. + */ + #define TX_BD_LONG_LFLAGS_T_IPID UINT32_C(0x80) + /* + * If set to '1', then the RoCE ICRC will be appended to the packet. + * Packet must be a valid RoCE format packet. + */ + #define TX_BD_LONG_LFLAGS_ROCE_CRC UINT32_C(0x100) + /* + * If set to '1', then the FCoE CRC will be appended to the packet. + * Packet must be a valid FCoE format packet. + */ + #define TX_BD_LONG_LFLAGS_FCOE_CRC UINT32_C(0x200) + uint16_t lflags; + + /* + * When LSO is '1', this field must contain the offset of the TCP + * payload from the beginning of the packet in as 16b words. In case of + * encapsulated/tunneling packet, this field contains the offset of the + * inner TCP payload from beginning of the packet as 16-bit words. This + * value must be valid on the first BD of a packet. + */ + #define TX_BD_LONG_HDR_SIZE_MASK UINT32_C(0x1ff) + #define TX_BD_LONG_HDR_SIZE_SFT 0 + uint16_t hdr_size; + + /* + * This is the MSS value that will be used to do the LSO processing. The + * value is the length in bytes of the TCP payload for each segment + * generated by the LSO operation. This value must be valid on the first + * BD of a packet. + */ + #define TX_BD_LONG_MSS_MASK UINT32_C(0x7fff) + #define TX_BD_LONG_MSS_SFT 0 + uint32_t mss; + + uint16_t unused_2; + + /* + * This value selects a CFA action to perform on the packet. Set this + * value to zero if no CFA action is desired. This value must be valid + * on the first BD of a packet. + */ + uint16_t cfa_action; + + /* + * This value is action meta-data that defines CFA edit operations that + * are done in addition to any action editing. + */ + /* When key=1, This is the VLAN tag VID value. */ + #define TX_BD_LONG_CFA_META_VLAN_VID_MASK UINT32_C(0xfff) + #define TX_BD_LONG_CFA_META_VLAN_VID_SFT 0 + /* When key=1, This is the VLAN tag DE value. */ + #define TX_BD_LONG_CFA_META_VLAN_DE UINT32_C(0x1000) + /* When key=1, This is the VLAN tag PRI value. */ + #define TX_BD_LONG_CFA_META_VLAN_PRI_MASK UINT32_C(0xe000) + #define TX_BD_LONG_CFA_META_VLAN_PRI_SFT 13 + /* When key=1, This is the VLAN tag TPID select value. */ + #define TX_BD_LONG_CFA_META_VLAN_TPID_MASK UINT32_C(0x70000) + #define TX_BD_LONG_CFA_META_VLAN_TPID_SFT 16 + /* 0x88a8 */ + #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID88A8 (UINT32_C(0x0) << 16) + /* 0x8100 */ + #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID8100 (UINT32_C(0x1) << 16) + /* 0x9100 */ + #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9100 (UINT32_C(0x2) << 16) + /* 0x9200 */ + #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9200 (UINT32_C(0x3) << 16) + /* 0x9300 */ + #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9300 (UINT32_C(0x4) << 16) + /* Value programmed in CFA VLANTPID register. */ + #define TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG (UINT32_C(0x5) << 16) + #define TX_BD_LONG_CFA_META_VLAN_TPID_LAST \ + TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG + /* When key=1, This is the VLAN tag TPID select value. */ + #define TX_BD_LONG_CFA_META_VLAN_RESERVED_MASK UINT32_C(0xff80000) + #define TX_BD_LONG_CFA_META_VLAN_RESERVED_SFT 19 + /* + * This field identifies the type of edit to be performed on the packet. + * This value must be valid on the first BD of a packet. + */ + #define TX_BD_LONG_CFA_META_KEY_MASK UINT32_C(0xf0000000) + #define TX_BD_LONG_CFA_META_KEY_SFT 28 + /* No editing */ + #define TX_BD_LONG_CFA_META_KEY_NONE (UINT32_C(0x0) << 28) + /* + * - meta[17:16] - TPID select value (0 = 0x8100). - meta[15:12] + * - PRI/DE value. - meta[11:0] - VID value. + */ + #define TX_BD_LONG_CFA_META_KEY_VLAN_TAG (UINT32_C(0x1) << 28) + #define TX_BD_LONG_CFA_META_KEY_LAST TX_BD_LONG_CFA_META_KEY_VLAN_TAG + uint32_t cfa_meta; +} __attribute__((packed)); + +/* RX Producer Packet BD (16 bytes) */ +struct rx_prod_pkt_bd { + /* This value identifies the type of buffer descriptor. */ + #define RX_PROD_PKT_BD_TYPE_MASK UINT32_C(0x3f) + #define RX_PROD_PKT_BD_TYPE_SFT 0 + /* + * Indicates that this BD is 16B long and is an RX Producer (ie. + * empty) buffer descriptor. + */ + #define RX_PROD_PKT_BD_TYPE_RX_PROD_PKT (UINT32_C(0x4) << 0) + /* + * If set to 1, the packet will be placed at the address plus 2B. The 2 + * Bytes of padding will be written as zero. + */ + /* + * This is intended to be used when the host buffer is cache-line + * aligned to produce packets that are easy to parse in host memory + * while still allowing writes to be cache line aligned. + */ + #define RX_PROD_PKT_BD_FLAGS_SOP_PAD UINT32_C(0x40) + /* + * If set to 1, the packet write will be padded out to the nearest + * cache-line with zero value padding. + */ + /* + * If receive buffers start/end on cache-line boundaries, this feature + * will ensure that all data writes on the PCI bus start/end on cache + * line boundaries. + */ + #define RX_PROD_PKT_BD_FLAGS_EOP_PAD UINT32_C(0x80) + /* + * This value is the number of additional buffers in the ring that + * describe the buffer space to be consumed for the this packet. If the + * value is zero, then the packet must fit within the space described by + * this BD. If this value is 1 or more, it indicates how many additional + * "buffer" BDs are in the ring immediately following this BD to be used + * for the same network packet. Even if the packet to be placed does not + * need all the additional buffers, they will be consumed anyway. + */ + #define RX_PROD_PKT_BD_FLAGS_BUFFERS_MASK UINT32_C(0x300) + #define RX_PROD_PKT_BD_FLAGS_BUFFERS_SFT 8 + #define RX_PROD_PKT_BD_FLAGS_MASK UINT32_C(0xffc0) + #define RX_PROD_PKT_BD_FLAGS_SFT 6 + uint16_t flags_type; + + /* + * This is the length in Bytes of the host physical buffer where data + * for the packet may be placed in host memory. + */ + /* + * While this is a Byte resolution value, it is often advantageous to + * ensure that the buffers provided end on a host cache line. + */ + uint16_t len; + + /* + * The opaque data field is pass through to the completion and can be + * used for any data that the driver wants to associate with this + * receive buffer set. + */ + uint32_t opaque; + + /* + * This is the host physical address where data for the packet may by + * placed in host memory. + */ + /* + * While this is a Byte resolution value, it is often advantageous to + * ensure that the buffers provide start on a host cache line. + */ + uint64_t addr; +} __attribute__((packed)); + +/* Completion Ring Structures */ +/* Note: This structure is used by the HWRM to communicate HWRM Error. */ +/* Base Completion Record (16 bytes) */ +struct cmpl_base { + /* unused is 10 b */ + /* + * This field indicates the exact type of the completion. By convention, + * the LSB identifies the length of the record in 16B units. Even values + * indicate 16B records. Odd values indicate 32B records. + */ + #define CMPL_BASE_TYPE_MASK UINT32_C(0x3f) + #define CMPL_BASE_TYPE_SFT 0 + /* TX L2 completion: Completion of TX packet. Length = 16B */ + #define CMPL_BASE_TYPE_TX_L2 (UINT32_C(0x0) << 0) + /* + * RX L2 completion: Completion of and L2 RX packet. + * Length = 32B + */ + #define CMPL_BASE_TYPE_RX_L2 (UINT32_C(0x11) << 0) + /* + * RX Aggregation Buffer completion : Completion of an L2 + * aggregation buffer in support of TPA, HDS, or Jumbo packet + * completion. Length = 16B + */ + #define CMPL_BASE_TYPE_RX_AGG (UINT32_C(0x12) << 0) + /* + * RX L2 TPA Start Completion: Completion at the beginning of a + * TPA operation. Length = 32B + */ + #define CMPL_BASE_TYPE_RX_TPA_START (UINT32_C(0x13) << 0) + /* + * RX L2 TPA End Completion: Completion at the end of a TPA + * operation. Length = 32B + */ + #define CMPL_BASE_TYPE_RX_TPA_END (UINT32_C(0x15) << 0) + /* + * Statistics Ejection Completion: Completion of statistics data + * ejection buffer. Length = 16B + */ + #define CMPL_BASE_TYPE_STAT_EJECT (UINT32_C(0x1a) << 0) + /* HWRM Command Completion: Completion of an HWRM command. */ + #define CMPL_BASE_TYPE_HWRM_DONE (UINT32_C(0x20) << 0) + /* Forwarded HWRM Request */ + #define CMPL_BASE_TYPE_HWRM_FWD_REQ (UINT32_C(0x22) << 0) + /* Forwarded HWRM Response */ + #define CMPL_BASE_TYPE_HWRM_FWD_RESP (UINT32_C(0x24) << 0) + /* HWRM Asynchronous Event Information */ + #define CMPL_BASE_TYPE_HWRM_ASYNC_EVENT (UINT32_C(0x2e) << 0) + /* CQ Notification */ + #define CMPL_BASE_TYPE_CQ_NOTIFICATION (UINT32_C(0x30) << 0) + /* SRQ Threshold Event */ + #define CMPL_BASE_TYPE_SRQ_EVENT (UINT32_C(0x32) << 0) + /* DBQ Threshold Event */ + #define CMPL_BASE_TYPE_DBQ_EVENT (UINT32_C(0x34) << 0) + /* QP Async Notification */ + #define CMPL_BASE_TYPE_QP_EVENT (UINT32_C(0x38) << 0) + /* Function Async Notification */ + #define CMPL_BASE_TYPE_FUNC_EVENT (UINT32_C(0x3a) << 0) + uint16_t type; + + uint16_t info1; + uint32_t info2; + + /* + * This value is written by the NIC such that it will be different for + * each pass through the completion queue. The even passes will write 1. + * The odd passes will write 0. + */ + #define CMPL_BASE_V UINT32_C(0x1) + /* info3 is 31 b */ + #define CMPL_BASE_INFO3_MASK UINT32_C(0xfffffffe) + #define CMPL_BASE_INFO3_SFT 1 + uint32_t info3_v; + + uint32_t info4; +} __attribute__((packed)); + +/* TX Completion Record (16 bytes) */ +struct tx_cmpl { + /* + * This field indicates the exact type of the completion. By convention, + * the LSB identifies the length of the record in 16B units. Even values + * indicate 16B records. Odd values indicate 32B records. + */ + #define TX_CMPL_TYPE_MASK UINT32_C(0x3f) + #define TX_CMPL_TYPE_SFT 0 + /* TX L2 completion: Completion of TX packet. Length = 16B */ + #define TX_CMPL_TYPE_TX_L2 (UINT32_C(0x0) << 0) + /* + * When this bit is '1', it indicates a packet that has an error of some + * type. Type of error is indicated in error_flags. + */ + #define TX_CMPL_FLAGS_ERROR UINT32_C(0x40) + /* + * When this bit is '1', it indicates that the packet completed was + * transmitted using the push acceleration data provided by the driver. + * When this bit is '0', it indicates that the packet had not push + * acceleration data written or was executed as a normal packet even + * though push data was provided. + */ + #define TX_CMPL_FLAGS_PUSH UINT32_C(0x80) + #define TX_CMPL_FLAGS_MASK UINT32_C(0xffc0) + #define TX_CMPL_FLAGS_SFT 6 + uint16_t flags_type; + + uint16_t unused_0; + + /* + * This is a copy of the opaque field from the first TX BD of this + * transmitted packet. + */ + uint32_t opaque; + + /* + * This value is written by the NIC such that it will be different for + * each pass through the completion queue. The even passes will write 1. + * The odd passes will write 0. + */ + #define TX_CMPL_V UINT32_C(0x1) + /* + * This error indicates that there was some sort of problem with the BDs + * for the packet. + */ + #define TX_CMPL_ERRORS_BUFFER_ERROR_MASK UINT32_C(0xe) + #define TX_CMPL_ERRORS_BUFFER_ERROR_SFT 1 + /* No error */ + #define TX_CMPL_ERRORS_BUFFER_ERROR_NO_ERROR (UINT32_C(0x0) << 1) + /* Bad Format: BDs were not formatted correctly. */ + #define TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT (UINT32_C(0x2) << 1) + #define TX_CMPL_ERRORS_BUFFER_ERROR_LAST \ + TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT + /* + * When this bit is '1', it indicates that the length of the packet was + * zero. No packet was transmitted. + */ + #define TX_CMPL_ERRORS_ZERO_LENGTH_PKT UINT32_C(0x10) + /* + * When this bit is '1', it indicates that the packet was longer than + * the programmed limit in TDI. No packet was transmitted. + */ + #define TX_CMPL_ERRORS_EXCESSIVE_BD_LENGTH UINT32_C(0x20) + /* + * When this bit is '1', it indicates that one or more of the BDs + * associated with this packet generated a PCI error. This probably + * means the address was not valid. + */ + #define TX_CMPL_ERRORS_DMA_ERROR UINT32_C(0x40) + /* + * When this bit is '1', it indicates that the packet was longer than + * indicated by the hint. No packet was transmitted. + */ + #define TX_CMPL_ERRORS_HINT_TOO_SHORT UINT32_C(0x80) + /* + * When this bit is '1', it indicates that the packet was dropped due to + * Poison TLP error on one or more of the TLPs in the PXP completion. + */ + #define TX_CMPL_ERRORS_POISON_TLP_ERROR UINT32_C(0x100) + #define TX_CMPL_ERRORS_MASK UINT32_C(0xfffe) + #define TX_CMPL_ERRORS_SFT 1 + uint16_t errors_v; + + uint16_t unused_1; + uint32_t unused_2; +} __attribute__((packed)) tx_cmpl_t, *ptx_cmpl_t; + +/* RX Packet Completion Record (32 bytes split to 2 16-byte struct) */ +struct rx_pkt_cmpl { + /* + * This field indicates the exact type of the completion. By convention, + * the LSB identifies the length of the record in 16B units. Even values + * indicate 16B records. Odd values indicate 32B records. + */ + #define RX_PKT_CMPL_TYPE_MASK UINT32_C(0x3f) + #define RX_PKT_CMPL_TYPE_SFT 0 + /* + * RX L2 completion: Completion of and L2 RX packet. + * Length = 32B + */ + #define RX_PKT_CMPL_TYPE_RX_L2 (UINT32_C(0x11) << 0) + /* + * When this bit is '1', it indicates a packet that has an error of some + * type. Type of error is indicated in error_flags. + */ + #define RX_PKT_CMPL_FLAGS_ERROR UINT32_C(0x40) + /* This field indicates how the packet was placed in the buffer. */ + #define RX_PKT_CMPL_FLAGS_PLACEMENT_MASK UINT32_C(0x380) + #define RX_PKT_CMPL_FLAGS_PLACEMENT_SFT 7 + /* Normal: Packet was placed using normal algorithm. */ + #define RX_PKT_CMPL_FLAGS_PLACEMENT_NORMAL (UINT32_C(0x0) << 7) + /* Jumbo: Packet was placed using jumbo algorithm. */ + #define RX_PKT_CMPL_FLAGS_PLACEMENT_JUMBO (UINT32_C(0x1) << 7) + /* + * Header/Data Separation: Packet was placed using Header/Data + * separation algorithm. The separation location is indicated by + * the itype field. + */ + #define RX_PKT_CMPL_FLAGS_PLACEMENT_HDS (UINT32_C(0x2) << 7) + #define RX_PKT_CMPL_FLAGS_PLACEMENT_LAST \ + RX_PKT_CMPL_FLAGS_PLACEMENT_HDS + /* This bit is '1' if the RSS field in this completion is valid. */ + #define RX_PKT_CMPL_FLAGS_RSS_VALID UINT32_C(0x400) + /* + * This value indicates what the inner packet determined for the packet + * was. + */ + #define RX_PKT_CMPL_FLAGS_ITYPE_MASK UINT32_C(0xf000) + #define RX_PKT_CMPL_FLAGS_ITYPE_SFT 12 + /* Not Known: Indicates that the packet type was not known. */ + #define RX_PKT_CMPL_FLAGS_ITYPE_NOT_KNOWN (UINT32_C(0x0) << 12) + /* + * IP Packet: Indicates that the packet was an IP packet, but + * further classification was not possible. + */ + #define RX_PKT_CMPL_FLAGS_ITYPE_IP (UINT32_C(0x1) << 12) + /* + * TCP Packet: Indicates that the packet was IP and TCP. This + * indicates that the payload_offset field is valid. + */ + #define RX_PKT_CMPL_FLAGS_ITYPE_TCP (UINT32_C(0x2) << 12) + /* + * UDP Packet: Indicates that the packet was IP and UDP. This + * indicates that the payload_offset field is valid. + */ + #define RX_PKT_CMPL_FLAGS_ITYPE_UDP (UINT32_C(0x3) << 12) + /* + * FCoE Packet: Indicates that the packet was recognized as a + * FCoE. This also indicates that the payload_offset field is + * valid. + */ + #define RX_PKT_CMPL_FLAGS_ITYPE_FCOE (UINT32_C(0x4) << 12) + /* + * RoCE Packet: Indicates that the packet was recognized as a + * RoCE. This also indicates that the payload_offset field is + * valid. + */ + #define RX_PKT_CMPL_FLAGS_ITYPE_ROCE (UINT32_C(0x5) << 12) + /* + * ICMP Packet: Indicates that the packet was recognized as + * ICMP. This indicates that the payload_offset field is valid. + */ + #define RX_PKT_CMPL_FLAGS_ITYPE_ICMP (UINT32_C(0x7) << 12) + /* + * PtP packet wo/timestamp: Indicates that the packet was + * recognized as a PtP packet. + */ + #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_WO_TIMESTAMP \ + (UINT32_C(0x8) << 12) + /* + * PtP packet w/timestamp: Indicates that the packet was + * recognized as a PtP packet and that a timestamp was taken for + * the packet. + */ + #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP (UINT32_C(0x9) << 12) + #define RX_PKT_CMPL_FLAGS_ITYPE_LAST \ + RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP + #define RX_PKT_CMPL_FLAGS_MASK UINT32_C(0xffc0) + #define RX_PKT_CMPL_FLAGS_SFT 6 + uint16_t flags_type; + + /* + * This is the length of the data for the packet stored in the buffer(s) + * identified by the opaque value. This includes the packet BD and any + * associated buffer BDs. This does not include the the length of any + * data places in aggregation BDs. + */ + uint16_t len; + + /* + * This is a copy of the opaque field from the RX BD this completion + * corresponds to. + */ + uint32_t opaque; + + /* + * This value is written by the NIC such that it will be different for + * each pass through the completion queue. The even passes will write 1. + * The odd passes will write 0. + */ + #define RX_PKT_CMPL_V1 UINT32_C(0x1) + /* + * This value is the number of aggregation buffers that follow this + * entry in the completion ring that are a part of this packet. If the + * value is zero, then the packet is completely contained in the buffer + * space provided for the packet in the RX ring. + */ + #define RX_PKT_CMPL_AGG_BUFS_MASK UINT32_C(0x3e) + #define RX_PKT_CMPL_AGG_BUFS_SFT 1 + uint8_t agg_bufs_v1; + + /* + * This is the RSS hash type for the packet. The value is packed + * {tuple_extrac_op[1:0],rss_profile_id[4:0],tuple_extrac_op[2]}. + */ + uint8_t rss_hash_type; + + /* + * This value indicates the offset from the beginning of the packet + * where the inner payload starts. This value is valid for TCP, UDP, + * FCoE, and RoCE packets. + */ + uint8_t payload_offset; + + uint8_t unused_1; + + /* + * This value is the RSS hash value calculated for the packet based on + * the mode bits and key value in the VNIC. + */ + uint32_t rss_hash; +} __attribute__((packed)); + +/* last 16 bytes of RX Packet Completion Record */ +struct rx_pkt_cmpl_hi { + /* + * This indicates that the ip checksum was calculated for the inner + * packet and that the ip_cs_error field indicates if there was an + * error. + */ + #define RX_PKT_CMPL_FLAGS2_IP_CS_CALC UINT32_C(0x1) + /* + * This indicates that the TCP, UDP or ICMP checksum was calculated for + * the inner packet and that the l4_cs_error field indicates if there + * was an error. + */ + #define RX_PKT_CMPL_FLAGS2_L4_CS_CALC UINT32_C(0x2) + /* + * This indicates that the ip checksum was calculated for the tunnel + * header and that the t_ip_cs_error field indicates if there was an + * error. + */ + #define RX_PKT_CMPL_FLAGS2_T_IP_CS_CALC UINT32_C(0x4) + /* + * This indicates that the UDP checksum was calculated for the tunnel + * packet and that the t_l4_cs_error field indicates if there was an + * error. + */ + #define RX_PKT_CMPL_FLAGS2_T_L4_CS_CALC UINT32_C(0x8) + /* This value indicates what format the metadata field is. */ + #define RX_PKT_CMPL_FLAGS2_META_FORMAT_MASK UINT32_C(0xf0) + #define RX_PKT_CMPL_FLAGS2_META_FORMAT_SFT 4 + /* No metadata informtaion. Value is zero. */ + #define RX_PKT_CMPL_FLAGS2_META_FORMAT_NONE (UINT32_C(0x0) << 4) + /* + * The metadata field contains the VLAN tag and TPID value. - + * metadata[11:0] contains the vlan VID value. - metadata[12] + * contains the vlan DE value. - metadata[15:13] contains the + * vlan PRI value. - metadata[31:16] contains the vlan TPID + * value. + */ + #define RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN (UINT32_C(0x1) << 4) + #define RX_PKT_CMPL_FLAGS2_META_FORMAT_LAST \ + RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN + /* + * This field indicates the IP type for the inner-most IP header. A + * value of '0' indicates IPv4. A value of '1' indicates IPv6. This + * value is only valid if itype indicates a packet with an IP header. + */ + #define RX_PKT_CMPL_FLAGS2_IP_TYPE UINT32_C(0x100) + uint32_t flags2; + + /* + * This is data from the CFA block as indicated by the meta_format + * field. + */ + /* When meta_format=1, this value is the VLAN VID. */ + #define RX_PKT_CMPL_METADATA_VID_MASK UINT32_C(0xfff) + #define RX_PKT_CMPL_METADATA_VID_SFT 0 + /* When meta_format=1, this value is the VLAN DE. */ + #define RX_PKT_CMPL_METADATA_DE UINT32_C(0x1000) + /* When meta_format=1, this value is the VLAN PRI. */ + #define RX_PKT_CMPL_METADATA_PRI_MASK UINT32_C(0xe000) + #define RX_PKT_CMPL_METADATA_PRI_SFT 13 + /* When meta_format=1, this value is the VLAN TPID. */ + #define RX_PKT_CMPL_METADATA_TPID_MASK UINT32_C(0xffff0000) + #define RX_PKT_CMPL_METADATA_TPID_SFT 16 + uint32_t metadata; + + /* + * This value is written by the NIC such that it will be different for + * each pass through the completion queue. The even passes will write 1. + * The odd passes will write 0. + */ + #define RX_PKT_CMPL_V2 UINT32_C(0x1) + /* + * This error indicates that there was some sort of problem with the BDs + * for the packet that was found after part of the packet was already + * placed. The packet should be treated as invalid. + */ + #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_MASK UINT32_C(0xe) + #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_SFT 1 + /* No buffer error */ + #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NO_BUFFER \ + (UINT32_C(0x0) << 1) + /* + * Did Not Fit: Packet did not fit into packet buffer provided. + * For regular placement, this means the packet did not fit in + * the buffer provided. For HDS and jumbo placement, this means + * that the packet could not be placed into 7 physical buffers + * or less. + */ + #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_DID_NOT_FIT \ + (UINT32_C(0x1) << 1) + /* + * Not On Chip: All BDs needed for the packet were not on-chip + * when the packet arrived. + */ + #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NOT_ON_CHIP \ + (UINT32_C(0x2) << 1) + /* Bad Format: BDs were not formatted correctly. */ + #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT \ + (UINT32_C(0x3) << 1) + #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_LAST \ + RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT + /* This indicates that there was an error in the IP header checksum. */ + #define RX_PKT_CMPL_ERRORS_IP_CS_ERROR UINT32_C(0x10) + /* + * This indicates that there was an error in the TCP, UDP or ICMP + * checksum. + */ + #define RX_PKT_CMPL_ERRORS_L4_CS_ERROR UINT32_C(0x20) + /* + * This indicates that there was an error in the tunnel IP header + * checksum. + */ + #define RX_PKT_CMPL_ERRORS_T_IP_CS_ERROR UINT32_C(0x40) + /* This indicates that there was an error in the tunnel UDP checksum. */ + #define RX_PKT_CMPL_ERRORS_T_L4_CS_ERROR UINT32_C(0x80) + /* + * This indicates that there was a CRC error on either an FCoE or RoCE + * packet. The itype indicates the packet type. + */ + #define RX_PKT_CMPL_ERRORS_CRC_ERROR UINT32_C(0x100) + /* + * This indicates that there was an error in the tunnel portion of the + * packet when this field is non-zero. + */ + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_MASK UINT32_C(0xe00) + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_SFT 9 + /* + * No additional error occurred on the tunnel portion of the + * packet of the packet does not have a tunnel. + */ + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_NO_ERROR (UINT32_C(0x0) << 9) + /* + * Indicates that IP header version does not match expectation + * from L2 Ethertype for IPv4 and IPv6 in the tunnel header. + */ + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_VERSION \ + (UINT32_C(0x1) << 9) + /* + * Indicates that header length is out of range in the tunnel + * header. Valid for IPv4. + */ + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_HDR_LEN \ + (UINT32_C(0x2) << 9) + /* + * Indicates that the physical packet is shorter than that + * claimed by the PPPoE header length for a tunnel PPPoE packet. + */ + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_TUNNEL_TOTAL_ERROR \ + (UINT32_C(0x3) << 9) + /* + * Indicates that physical packet is shorter than that claimed + * by the tunnel l3 header length. Valid for IPv4, or IPv6 + * tunnel packet packets. + */ + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_IP_TOTAL_ERROR \ + (UINT32_C(0x4) << 9) + /* + * Indicates that the physical packet is shorter than that + * claimed by the tunnel UDP header length for a tunnel UDP + * packet that is not fragmented. + */ + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_UDP_TOTAL_ERROR \ + (UINT32_C(0x5) << 9) + /* + * indicates that the IPv4 TTL or IPv6 hop limit check have + * failed (e.g. TTL = 0) in the tunnel header. Valid for IPv4, + * and IPv6. + */ + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL \ + (UINT32_C(0x6) << 9) + #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_LAST \ + RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL + /* + * This indicates that there was an error in the inner portion of the + * packet when this field is non-zero. + */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_MASK UINT32_C(0xf000) + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_SFT 12 + /* + * No additional error occurred on the tunnel portion of the + * packet of the packet does not have a tunnel. + */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_NO_ERROR (UINT32_C(0x0) << 12) + /* + * Indicates that IP header version does not match expectation + * from L2 Ethertype for IPv4 and IPv6 or that option other than + * VFT was parsed on FCoE packet. + */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_VERSION \ + (UINT32_C(0x1) << 12) + /* + * indicates that header length is out of range. Valid for IPv4 + * and RoCE + */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_HDR_LEN \ + (UINT32_C(0x2) << 12) + /* + * indicates that the IPv4 TTL or IPv6 hop limit check have + * failed (e.g. TTL = 0). Valid for IPv4, and IPv6 + */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_TTL (UINT32_C(0x3) << 12) + /* + * Indicates that physical packet is shorter than that claimed + * by the l3 header length. Valid for IPv4, IPv6 packet or RoCE + * packets. + */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_IP_TOTAL_ERROR \ + (UINT32_C(0x4) << 12) + /* + * Indicates that the physical packet is shorter than that + * claimed by the UDP header length for a UDP packet that is not + * fragmented. + */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_UDP_TOTAL_ERROR \ + (UINT32_C(0x5) << 12) + /* + * Indicates that TCP header length > IP payload. Valid for TCP + * packets only. + */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN \ + (UINT32_C(0x6) << 12) + /* Indicates that TCP header length < 5. Valid for TCP. */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN_TOO_SMALL \ + (UINT32_C(0x7) << 12) + /* + * Indicates that TCP option headers result in a TCP header size + * that does not match data offset in TCP header. Valid for TCP. + */ + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN \ + (UINT32_C(0x8) << 12) + #define RX_PKT_CMPL_ERRORS_PKT_ERROR_LAST \ + RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN + #define RX_PKT_CMPL_ERRORS_MASK UINT32_C(0xfffe) + #define RX_PKT_CMPL_ERRORS_SFT 1 + uint16_t errors_v2; + + /* + * This field identifies the CFA action rule that was used for this + * packet. + */ + uint16_t cfa_code; + + /* + * This value holds the reordering sequence number for the packet. If + * the reordering sequence is not valid, then this value is zero. The + * reordering domain for the packet is in the bottom 8 to 10b of the + * rss_hash value. The bottom 20b of this value contain the ordering + * domain value for the packet. + */ + #define RX_PKT_CMPL_REORDER_MASK UINT32_C(0xffffff) + #define RX_PKT_CMPL_REORDER_SFT 0 + uint32_t reorder; +} __attribute__((packed)); + +/* HWRM Forwarded Request (16 bytes) */ +struct hwrm_fwd_req_cmpl { + /* Length of forwarded request in bytes. */ + /* + * This field indicates the exact type of the completion. By convention, + * the LSB identifies the length of the record in 16B units. Even values + * indicate 16B records. Odd values indicate 32B records. + */ + #define HWRM_FWD_REQ_CMPL_TYPE_MASK UINT32_C(0x3f) + #define HWRM_FWD_REQ_CMPL_TYPE_SFT 0 + /* Forwarded HWRM Request */ + #define HWRM_FWD_REQ_CMPL_TYPE_HWRM_FWD_REQ (UINT32_C(0x22) << 0) + /* Length of forwarded request in bytes. */ + #define HWRM_FWD_REQ_CMPL_REQ_LEN_MASK UINT32_C(0xffc0) + #define HWRM_FWD_REQ_CMPL_REQ_LEN_SFT 6 + uint16_t req_len_type; + + /* + * Source ID of this request. Typically used in forwarding requests and + * responses. 0x0 - 0xFFF8 - Used for function ids 0xFFF8 - 0xFFFE - + * Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t source_id; + + uint32_t unused_0; + + /* Address of forwarded request. */ + /* + * This value is written by the NIC such that it will be different for + * each pass through the completion queue. The even passes will write 1. + * The odd passes will write 0. + */ + #define HWRM_FWD_REQ_CMPL_V UINT32_C(0x1) + /* Address of forwarded request. */ + #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_MASK UINT32_C(0xfffffffe) + #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_SFT 1 + uint64_t req_buf_addr_v; +} __attribute__((packed)); + +/* HWRM Asynchronous Event Completion Record (16 bytes) */ +struct hwrm_async_event_cmpl { + /* + * This field indicates the exact type of the completion. By convention, + * the LSB identifies the length of the record in 16B units. Even values + * indicate 16B records. Odd values indicate 32B records. + */ + #define HWRM_ASYNC_EVENT_CMPL_TYPE_MASK UINT32_C(0x3f) + #define HWRM_ASYNC_EVENT_CMPL_TYPE_SFT 0 + /* HWRM Asynchronous Event Information */ + #define HWRM_ASYNC_EVENT_CMPL_TYPE_HWRM_ASYNC_EVENT \ + (UINT32_C(0x2e) << 0) + uint16_t type; + + /* Identifiers of events. */ + /* Link status changed */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_STATUS_CHANGE \ + (UINT32_C(0x0) << 0) + /* Link MTU changed */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_MTU_CHANGE \ + (UINT32_C(0x1) << 0) + /* Link speed changed */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CHANGE \ + (UINT32_C(0x2) << 0) + /* DCB Configuration changed */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_DCB_CONFIG_CHANGE \ + (UINT32_C(0x3) << 0) + /* Port connection not allowed */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_CONN_NOT_ALLOWED \ + (UINT32_C(0x4) << 0) + /* Link speed configuration was not allowed */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_NOT_ALLOWED \ + (UINT32_C(0x5) << 0) + /* Function driver unloaded */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_UNLOAD \ + (UINT32_C(0x10) << 0) + /* Function driver loaded */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_LOAD \ + (UINT32_C(0x11) << 0) + /* PF driver unloaded */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_UNLOAD \ + (UINT32_C(0x20) << 0) + /* PF driver loaded */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_LOAD \ + (UINT32_C(0x21) << 0) + /* VF Function Level Reset (FLR) */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_FLR (UINT32_C(0x30) << 0) + /* VF MAC Address Change */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_MAC_ADDR_CHANGE \ + (UINT32_C(0x31) << 0) + /* PF-VF communication channel status change. */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_VF_COMM_STATUS_CHANGE \ + (UINT32_C(0x32) << 0) + /* HWRM Error */ + #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_HWRM_ERROR \ + (UINT32_C(0xff) << 0) + uint16_t event_id; + + /* Event specific data */ + uint32_t event_data2; + + /* opaque is 7 b */ + /* + * This value is written by the NIC such that it will be different for + * each pass through the completion queue. The even passes will write 1. + * The odd passes will write 0. + */ + #define HWRM_ASYNC_EVENT_CMPL_V UINT32_C(0x1) + /* opaque is 7 b */ + #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_MASK UINT32_C(0xfe) + #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_SFT 1 + uint8_t opaque_v; + + /* 8-lsb timestamp from POR (100-msec resolution) */ + uint8_t timestamp_lo; + + /* 16-lsb timestamp from POR (100-msec resolution) */ + uint16_t timestamp_hi; + + /* Event specific data */ + uint32_t event_data1; +} __attribute__((packed)); + +/* + * Note: The Hardware Resource Manager (HWRM) manages various hardware resources + * inside the chip. The HWRM is implemented in firmware, and runs on embedded + * processors inside the chip. This firmware is vital part of the chip's + * hardware. The chip can not be used by driver without it. + */ + +/* Input (16 bytes) */ +struct input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; +} __attribute__((packed)); + +/* Output (8 bytes) */ +struct output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; +} __attribute__((packed)); + +/* hwrm_cfa_l2_filter_alloc */ +/* + * A filter is used to identify traffic that contains a matching set of + * parameters like unicast or broadcast MAC address or a VLAN tag amongst + * other things which then allows the ASIC to direct the incoming traffic + * to an appropriate VNIC or Rx ring. + */ + +/* Input (96 bytes) */ +struct hwrm_cfa_l2_filter_alloc_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * Enumeration denoting the RX, TX type of the resource. This + * enumeration is used for resources that are similar for both TX and RX + * paths of the chip. + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH \ + UINT32_C(0x1) + /* tx path */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_TX \ + (UINT32_C(0x0) << 0) + /* rx path */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX \ + (UINT32_C(0x1) << 0) + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_LAST \ + HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX + /* + * Setting of this flag indicates the applicability to the loopback + * path. + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \ + UINT32_C(0x2) + /* + * Setting of this flag indicates drop action. If this flag is not set, + * then it should be considered accept action. + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_DROP \ + UINT32_C(0x4) + /* + * If this flag is set, all t_l2_* fields are invalid and they should + * not be specified. If this flag is set, then l2_* fields refer to + * fields of outermost L2 header. + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_OUTERMOST \ + UINT32_C(0x8) + uint32_t flags; + + /* This bit must be '1' for the l2_addr field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR \ + UINT32_C(0x1) + /* This bit must be '1' for the l2_addr_mask field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR_MASK \ + UINT32_C(0x2) + /* This bit must be '1' for the l2_ovlan field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN \ + UINT32_C(0x4) + /* This bit must be '1' for the l2_ovlan_mask field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN_MASK \ + UINT32_C(0x8) + /* This bit must be '1' for the l2_ivlan field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN \ + UINT32_C(0x10) + /* This bit must be '1' for the l2_ivlan_mask field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN_MASK \ + UINT32_C(0x20) + /* This bit must be '1' for the t_l2_addr field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR \ + UINT32_C(0x40) + /* + * This bit must be '1' for the t_l2_addr_mask field to be configured. + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR_MASK \ + UINT32_C(0x80) + /* This bit must be '1' for the t_l2_ovlan field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN \ + UINT32_C(0x100) + /* + * This bit must be '1' for the t_l2_ovlan_mask field to be configured. + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN_MASK \ + UINT32_C(0x200) + /* This bit must be '1' for the t_l2_ivlan field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN \ + UINT32_C(0x400) + /* + * This bit must be '1' for the t_l2_ivlan_mask field to be configured. + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN_MASK \ + UINT32_C(0x800) + /* This bit must be '1' for the src_type field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_TYPE \ + UINT32_C(0x1000) + /* This bit must be '1' for the src_id field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_ID \ + UINT32_C(0x2000) + /* This bit must be '1' for the tunnel_type field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \ + UINT32_C(0x4000) + /* This bit must be '1' for the dst_id field to be configured. */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_DST_ID \ + UINT32_C(0x8000) + /* + * This bit must be '1' for the mirror_vnic_id field to be configured. + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \ + UINT32_C(0x10000) + uint32_t enables; + + /* + * This value sets the match value for the L2 MAC address. Destination + * MAC address for RX path. Source MAC address for TX path. + */ + uint8_t l2_addr[6]; + + uint8_t unused_0; + uint8_t unused_1; + + /* + * This value sets the mask value for the L2 address. A value of 0 will + * mask the corresponding bit from compare. + */ + uint8_t l2_addr_mask[6]; + + /* This value sets VLAN ID value for outer VLAN. */ + uint16_t l2_ovlan; + + /* + * This value sets the mask value for the ovlan id. A value of 0 will + * mask the corresponding bit from compare. + */ + uint16_t l2_ovlan_mask; + + /* This value sets VLAN ID value for inner VLAN. */ + uint16_t l2_ivlan; + + /* + * This value sets the mask value for the ivlan id. A value of 0 will + * mask the corresponding bit from compare. + */ + uint16_t l2_ivlan_mask; + + uint8_t unused_2; + uint8_t unused_3; + + /* + * This value sets the match value for the tunnel L2 MAC address. + * Destination MAC address for RX path. Source MAC address for TX path. + */ + uint8_t t_l2_addr[6]; + + uint8_t unused_4; + uint8_t unused_5; + + /* + * This value sets the mask value for the tunnel L2 address. A value of + * 0 will mask the corresponding bit from compare. + */ + uint8_t t_l2_addr_mask[6]; + + /* This value sets VLAN ID value for tunnel outer VLAN. */ + uint16_t t_l2_ovlan; + + /* + * This value sets the mask value for the tunnel ovlan id. A value of 0 + * will mask the corresponding bit from compare. + */ + uint16_t t_l2_ovlan_mask; + + /* This value sets VLAN ID value for tunnel inner VLAN. */ + uint16_t t_l2_ivlan; + + /* + * This value sets the mask value for the tunnel ivlan id. A value of 0 + * will mask the corresponding bit from compare. + */ + uint16_t t_l2_ivlan_mask; + + /* This value identifies the type of source of the packet. */ + /* Network port */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_NPORT \ + (UINT32_C(0x0) << 0) + /* Physical function */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_PF \ + (UINT32_C(0x1) << 0) + /* Virtual function */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VF \ + (UINT32_C(0x2) << 0) + /* Virtual NIC of a function */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VNIC \ + (UINT32_C(0x3) << 0) + /* Embedded processor for CFA management */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_KONG \ + (UINT32_C(0x4) << 0) + /* Embedded processor for OOB management */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_APE \ + (UINT32_C(0x5) << 0) + /* Embedded processor for RoCE */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_BONO \ + (UINT32_C(0x6) << 0) + /* Embedded processor for network proxy functions */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_TANG \ + (UINT32_C(0x7) << 0) + uint8_t src_type; + + uint8_t unused_6; + /* + * This value is the id of the source. For a network port, it represents + * port_id. For a physical function, it represents fid. For a virtual + * function, it represents vf_id. For a vnic, it represents vnic_id. For + * embedded processors, this id is not valid. Notes: 1. The function ID + * is implied if it src_id is not provided for a src_type that is either + */ + uint32_t src_id; + + /* Tunnel Type. */ + /* Non-tunnel */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \ + (UINT32_C(0x0) << 0) + /* Virtual eXtensible Local Area Network (VXLAN) */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \ + (UINT32_C(0x1) << 0) + /* + * Network Virtualization Generic Routing Encapsulation (NVGRE) + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \ + (UINT32_C(0x2) << 0) + /* + * Generic Routing Encapsulation (GRE) inside Ethernet payload + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \ + (UINT32_C(0x3) << 0) + /* IP in IP */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \ + (UINT32_C(0x4) << 0) + /* Generic Network Virtualization Encapsulation (Geneve) */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \ + (UINT32_C(0x5) << 0) + /* Multi-Protocol Lable Switching (MPLS) */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \ + (UINT32_C(0x6) << 0) + /* Stateless Transport Tunnel (STT) */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \ + (UINT32_C(0x7) << 0) + /* + * Generic Routing Encapsulation (GRE) inside IP datagram + * payload + */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \ + (UINT32_C(0x8) << 0) + /* Any tunneled traffic */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \ + (UINT32_C(0xff) << 0) + uint8_t tunnel_type; + + uint8_t unused_7; + + /* + * If set, this value shall represent the Logical VNIC ID of the + * destination VNIC for the RX path and network port id of the + * destination port for the TX path. + */ + uint16_t dst_id; + + /* Logical VNIC ID of the VNIC where traffic is mirrored. */ + uint16_t mirror_vnic_id; + + /* + * This hint is provided to help in placing the filter in the filter + * table. + */ + /* No preference */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \ + (UINT32_C(0x0) << 0) + /* Above the given filter */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE_FILTER \ + (UINT32_C(0x1) << 0) + /* Below the given filter */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_BELOW_FILTER \ + (UINT32_C(0x2) << 0) + /* As high as possible */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MAX \ + (UINT32_C(0x3) << 0) + /* As low as possible */ + #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MIN \ + (UINT32_C(0x4) << 0) + uint8_t pri_hint; + + uint8_t unused_8; + uint32_t unused_9; + + /* + * This is the ID of the filter that goes along with the pri_hint. This + * field is valid only for the following values. 1 - Above the given + * filter 2 - Below the given filter + */ + uint64_t l2_filter_id_hint; +} __attribute__((packed)); + +/* Output (24 bytes) */ +struct hwrm_cfa_l2_filter_alloc_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* + * This value identifies a set of CFA data structures used for an L2 + * context. + */ + uint64_t l2_filter_id; + + /* + * This is the ID of the flow associated with this filter. This value + * shall be used to match and associate the flow identifier returned in + * completion records. A value of 0xFFFFFFFF shall indicate no flow id. + */ + uint32_t flow_id; + + uint8_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_cfa_l2_filter_free */ +/* + * Description: Free a L2 filter. The HWRM shall free all associated filter + * resources with the L2 filter. + */ + +/* Input (24 bytes) */ +struct hwrm_cfa_l2_filter_free_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * This value identifies a set of CFA data structures used for an L2 + * context. + */ + uint64_t l2_filter_id; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_cfa_l2_filter_free_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_cfa_l2_set_rx_mask */ +/* Description: This command will set rx mask of the function. */ + +/* Input (40 bytes) */ +struct hwrm_cfa_l2_set_rx_mask_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* VNIC ID */ + uint32_t vnic_id; + + /* Reserved for future use. */ + #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_RESERVED UINT32_C(0x1) + /* + * When this bit is '1', the function is requested to accept multi-cast + * packets specified by the multicast addr table. + */ + #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST UINT32_C(0x2) + /* + * When this bit is '1', the function is requested to accept all multi- + * cast packets. + */ + #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ALL_MCAST UINT32_C(0x4) + /* + * When this bit is '1', the function is requested to accept broadcast + * packets. + */ + #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_BCAST UINT32_C(0x8) + /* + * When this bit is '1', the function is requested to be put in the + * promiscuous mode. The HWRM should accept any function to set up + * promiscuous mode. The HWRM shall follow the semantics below for the + * promiscuous mode support. # When partitioning is not enabled on a + * port (i.e. single PF on the port), then the PF shall be allowed to be + * in the promiscuous mode. When the PF is in the promiscuous mode, then + * it shall receive all host bound traffic on that port. # When + * partitioning is enabled on a port (i.e. multiple PFs per port) and a + * PF on that port is in the promiscuous mode, then the PF receives all + * traffic within that partition as identified by a unique identifier + * for the PF (e.g. S-Tag). If a unique outer VLAN for the PF is + * specified, then the setting of promiscuous mode on that PF shall + * result in the PF receiving all host bound traffic with matching outer + * VLAN. # A VF shall can be set in the promiscuous mode. In the + * promiscuous mode, the VF does not receive any traffic unless a unique + * outer VLAN for the VF is specified. If a unique outer VLAN for the VF + * is specified, then the setting of promiscuous mode on that VF shall + * result in the VF receiving all host bound traffic with the matching + * outer VLAN. # The HWRM shall allow the setting of promiscuous mode on + * a function independently from the promiscuous mode settings on other + * functions. + */ + #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_PROMISCUOUS UINT32_C(0x10) + /* + * If this flag is set, the corresponding RX filters shall be set up to + * cover multicast/broadcast filters for the outermost Layer 2 + * destination MAC address field. + */ + #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_OUTERMOST UINT32_C(0x20) + uint32_t mask; + + /* This is the address for mcast address tbl. */ + uint64_t mc_tbl_addr; + + /* + * This value indicates how many entries in mc_tbl are valid. Each entry + * is 6 bytes. + */ + uint32_t num_mc_entries; + + uint32_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_cfa_l2_set_rx_mask_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_exec_fwd_resp */ +/* + * Description: This command is used to send an encapsulated request to the + * HWRM. This command instructs the HWRM to execute the request and forward the + * response of the encapsulated request to the location specified in the + * original request that is encapsulated. The target id of this command shall be + * set to 0xFFFF (HWRM). The response location in this command shall be used to + * acknowledge the receipt of the encapsulated request and forwarding of the + * response. + */ + +/* Input (128 bytes) */ +struct hwrm_exec_fwd_resp_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * This is an encapsulated request. This request should be executed by + * the HWRM and the response should be provided in the response buffer + * inside the encapsulated request. + */ + uint32_t encap_request[26]; + + /* + * This value indicates the target id of the response to the + * encapsulated request. 0x0 - 0xFFF8 - Used for function ids 0xFFF8 - + * 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t encap_resp_target_id; + + uint16_t unused_0[3]; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_exec_fwd_resp_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_func_qcaps */ +/* + * Description: This command returns capabilities of a function. The input FID + * value is used to indicate what function is being queried. This allows a + * physical function driver to query virtual functions that are children of the + * physical function. The output FID value is needed to configure Rings and + * MSI-X vectors so their DMA operations appear correctly on the PCI bus. + */ + +/* Input (24 bytes) */ +struct hwrm_func_qcaps_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * Function ID of the function that is being queried. 0xFF... (All Fs) + * if the query is for the requesting function. + */ + uint16_t fid; + + uint16_t unused_0[3]; +} __attribute__((packed)); + +/* Output (80 bytes) */ +struct hwrm_func_qcaps_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* + * FID value. This value is used to identify operations on the PCI bus + * as belonging to a particular PCI function. + */ + uint16_t fid; + + /* + * Port ID of port that this function is associated with. Valid only for + * the PF. 0xFF... (All Fs) if this function is not associated with any + * port. 0xFF... (All Fs) if this function is called from a VF. + */ + uint16_t port_id; + + /* If 1, then Push mode is supported on this function. */ + #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PUSH_MODE_SUPPORTED UINT32_C(0x1) + /* + * If 1, then the global MSI-X auto-masking is enabled for the device. + */ + #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_GLOBAL_MSIX_AUTOMASKING \ + UINT32_C(0x2) + /* + * If 1, then the Precision Time Protocol (PTP) processing is supported + * on this function. The HWRM should enable PTP on only a single + * Physical Function (PF) per port. + */ + #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PTP_SUPPORTED UINT32_C(0x4) + uint32_t flags; + + /* + * This value is current MAC address configured for this function. A + * value of 00-00-00-00-00-00 indicates no MAC address is currently + * configured. + */ + uint8_t perm_mac_address[6]; + + /* + * The maximum number of RSS/COS contexts that can be allocated to the + * function. + */ + uint16_t max_rsscos_ctx; + + /* + * The maximum number of completion rings that can be allocated to the + * function. + */ + uint16_t max_cmpl_rings; + + /* + * The maximum number of transmit rings that can be allocated to the + * function. + */ + uint16_t max_tx_rings; + + /* + * The maximum number of receive rings that can be allocated to the + * function. + */ + uint16_t max_rx_rings; + + /* + * The maximum number of L2 contexts that can be allocated to the + * function. + */ + uint16_t max_l2_ctxs; + + /* The maximum number of VNICs that can be allocated to the function. */ + uint16_t max_vnics; + + /* + * The identifier for the first VF enabled on a PF. This is valid only + * on the PF with SR-IOV enabled. 0xFF... (All Fs) if this command is + * called on a PF with SR-IOV disabled or on a VF. + */ + uint16_t first_vf_id; + + /* + * The maximum number of VFs that can be allocated to the function. This + * is valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if this + * command is called on a PF with SR-IOV disabled or on a VF. + */ + uint16_t max_vfs; + + /* + * The maximum number of statistic contexts that can be allocated to the + * function. + */ + uint16_t max_stat_ctx; + + /* + * The maximum number of Encapsulation records that can be offloaded by + * this function. + */ + uint32_t max_encap_records; + + /* + * The maximum number of decapsulation records that can be offloaded by + * this function. + */ + uint32_t max_decap_records; + + /* + * The maximum number of Exact Match (EM) flows that can be offloaded by + * this function on the TX side. + */ + uint32_t max_tx_em_flows; + + /* + * The maximum number of Wildcard Match (WM) flows that can be offloaded + * by this function on the TX side. + */ + uint32_t max_tx_wm_flows; + + /* + * The maximum number of Exact Match (EM) flows that can be offloaded by + * this function on the RX side. + */ + uint32_t max_rx_em_flows; + + /* + * The maximum number of Wildcard Match (WM) flows that can be offloaded + * by this function on the RX side. + */ + uint32_t max_rx_wm_flows; + + /* + * The maximum number of multicast filters that can be supported by this + * function on the RX side. + */ + uint32_t max_mcast_filters; + + /* + * The maximum value of flow_id that can be supported in completion + * records. + */ + uint32_t max_flow_id; + + /* + * The maximum number of HW ring groups that can be supported on this + * function. + */ + uint32_t max_hw_ring_grps; + + uint8_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_func_reset */ +/* + * Description: This command resets a hardware function (PCIe function) and + * frees any resources used by the function. This command shall be initiated by + * the driver after an FLR has occurred to prepare the function for re-use. This + * command may also be initiated by a driver prior to doing it's own + * configuration. This command puts the function into the reset state. In the + * reset state, global and port related features of the chip are not available. + */ +/* + * Note: This command will reset a function that has already been disabled or + * idled. The command returns all the resources owned by the function so a new + * driver may allocate and configure resources normally. + */ + +/* Input (24 bytes) */ +struct hwrm_func_reset_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* This bit must be '1' for the vf_id_valid field to be configured. */ + #define HWRM_FUNC_RESET_INPUT_ENABLES_VF_ID_VALID \ + UINT32_C(0x1) + uint32_t enables; + + /* + * The ID of the VF that this PF is trying to reset. Only the parent PF + * shall be allowed to reset a child VF. A parent PF driver shall use + * this field only when a specific child VF is requested to be reset. + */ + uint16_t vf_id; + + /* This value indicates the level of a function reset. */ + /* + * Reset the caller function and its children VFs (if any). If + * no children functions exist, then reset the caller function + * only. + */ + #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETALL \ + (UINT32_C(0x0) << 0) + /* Reset the caller function only */ + #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETME \ + (UINT32_C(0x1) << 0) + /* + * Reset all children VFs of the caller function driver if the + * caller is a PF driver. It is an error to specify this level + * by a VF driver. It is an error to specify this level by a PF + * driver with no children VFs. + */ + #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETCHILDREN \ + (UINT32_C(0x2) << 0) + /* + * Reset a specific VF of the caller function driver if the + * caller is the parent PF driver. It is an error to specify + * this level by a VF driver. It is an error to specify this + * level by a PF driver that is not the parent of the VF that is + * being requested to reset. + */ + #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETVF \ + (UINT32_C(0x3) << 0) + uint8_t func_reset_level; + + uint8_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_func_reset_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_port_phy_cfg */ +/* + * Description: This command configures the PHY device for the port. It allows + * setting of the most generic settings for the PHY. The HWRM shall complete + * this command as soon as PHY settings are configured. They may not be applied + * when the command response is provided. A VF driver shall not be allowed to + * configure PHY using this command. In a network partition mode, a PF driver + * shall not be allowed to configure PHY using this command. + */ + +/* Input (56 bytes) */ +struct hwrm_port_phy_cfg_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * When this bit is set to '1', the PHY for the port shall be reset. # + * If this bit is set to 1, then the HWRM shall reset the PHY after + * applying PHY configuration changes specified in this command. # In + * order to guarantee that PHY configuration changes specified in this + * command take effect, the HWRM client should set this flag to 1. # If + * this bit is not set to 1, then the HWRM may reset the PHY depending + * on the current PHY configuration and settings specified in this + * command. + */ + #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY UINT32_C(0x1) + /* + * When this bit is set to '1', the link shall be forced to be taken + * down. # When this bit is set to '1", all other command input settings + * related to the link speed shall be ignored. Once the link state is + * forced down, it can be explicitly cleared from that state by setting + * this flag to '0'. # If this flag is set to '0', then the link shall + * be cleared from forced down state if the link is in forced down + * state. There may be conditions (e.g. out-of-band or sideband + * configuration changes for the link) outside the scope of the HWRM + * implementation that may clear forced down link state. + */ + #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE_LINK_DOWN UINT32_C(0x2) + /* + * When this bit is set to '1', the link shall be forced to the + * force_link_speed value. When this bit is set to '1', the HWRM client + * should not enable any of the auto negotiation related fields + * represented by auto_XXX fields in this command. When this bit is set + * to '1' and the HWRM client has enabled a auto_XXX field in this + * command, then the HWRM shall ignore the enabled auto_XXX field. When + * this bit is set to zero, the link shall be allowed to autoneg. + */ + #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE UINT32_C(0x4) + /* + * When this bit is set to '1', the auto-negotiation process shall be + * restarted on the link. + */ + #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG UINT32_C(0x8) + /* + * When this bit is set to '1', Energy Efficient Ethernet (EEE) is + * requested to be enabled on this link. If EEE is not supported on this + * port, then this flag shall be ignored by the HWRM. + */ + #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_ENABLE UINT32_C(0x10) + /* + * When this bit is set to '1', Energy Efficient Ethernet (EEE) is + * requested to be disabled on this link. If EEE is not supported on + * this port, then this flag shall be ignored by the HWRM. + */ + #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_DISABLE UINT32_C(0x20) + /* + * When this bit is set to '1' and EEE is enabled on this link, then TX + * LPI is requested to be enabled on the link. If EEE is not supported + * on this port, then this flag shall be ignored by the HWRM. If EEE is + * disabled on this port, then this flag shall be ignored by the HWRM. + */ + #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI UINT32_C(0x40) + uint32_t flags; + + /* This bit must be '1' for the auto_mode field to be configured. */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_MODE UINT32_C(0x1) + /* This bit must be '1' for the auto_duplex field to be configured. */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_DUPLEX UINT32_C(0x2) + /* This bit must be '1' for the auto_pause field to be configured. */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_PAUSE UINT32_C(0x4) + /* + * This bit must be '1' for the auto_link_speed field to be configured. + */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED UINT32_C(0x8) + /* + * This bit must be '1' for the auto_link_speed_mask field to be + * configured. + */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED_MASK \ + UINT32_C(0x10) + /* This bit must be '1' for the wirespeed field to be configured. */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_WIRESPEED UINT32_C(0x20) + /* This bit must be '1' for the lpbk field to be configured. */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_LPBK UINT32_C(0x40) + /* This bit must be '1' for the preemphasis field to be configured. */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_PREEMPHASIS UINT32_C(0x80) + /* This bit must be '1' for the force_pause field to be configured. */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE UINT32_C(0x100) + /* + * This bit must be '1' for the eee_link_speed_mask field to be + * configured. + */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_EEE_LINK_SPEED_MASK \ + UINT32_C(0x200) + /* This bit must be '1' for the tx_lpi_timer field to be configured. */ + #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_TX_LPI_TIMER UINT32_C(0x400) + uint32_t enables; + + /* Port ID of port that is to be configured. */ + uint16_t port_id; + + /* + * This is the speed that will be used if the force bit is '1'. If + * unsupported speed is selected, an error will be generated. + */ + /* 100Mb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100MB \ + (UINT32_C(0x1) << 0) + /* 1Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_1GB \ + (UINT32_C(0xa) << 0) + /* 2Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2GB \ + (UINT32_C(0x14) << 0) + /* 2.5Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2_5GB \ + (UINT32_C(0x19) << 0) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10GB \ + (UINT32_C(0x64) << 0) + /* 20Mb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_20GB \ + (UINT32_C(0xc8) << 0) + /* 25Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_25GB \ + (UINT32_C(0xfa) << 0) + /* 40Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_40GB \ + (UINT32_C(0x190) << 0) + /* 50Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_50GB \ + (UINT32_C(0x1f4) << 0) + /* 100Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100GB \ + (UINT32_C(0x3e8) << 0) + /* 10Mb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10MB \ + (UINT32_C(0xffff) << 0) + uint16_t force_link_speed; + + /* + * This value is used to identify what autoneg mode is used when the + * link speed is not being forced. + */ + /* + * Disable autoneg or autoneg disabled. No speeds are selected. + */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE (UINT32_C(0x0) << 0) + /* Select all possible speeds for autoneg mode. */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ALL_SPEEDS \ + (UINT32_C(0x1) << 0) + /* + * Select only the auto_link_speed speed for autoneg mode. This + * mode has been DEPRECATED. An HWRM client should not use this + * mode. + */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_SPEED \ + (UINT32_C(0x2) << 0) + /* + * Select the auto_link_speed or any speed below that speed for + * autoneg. This mode has been DEPRECATED. An HWRM client should + * not use this mode. + */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_OR_BELOW \ + (UINT32_C(0x3) << 0) + /* + * Select the speeds based on the corresponding link speed mask + * value that is provided. + */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_SPEED_MASK \ + (UINT32_C(0x4) << 0) + uint8_t auto_mode; + + /* + * This is the duplex setting that will be used if the autoneg_mode is + * "one_speed" or "one_or_below". + */ + /* Half Duplex will be requested. */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_HALF \ + (UINT32_C(0x0) << 0) + /* Full duplex will be requested. */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_FULL \ + (UINT32_C(0x1) << 0) + /* Both Half and Full dupex will be requested. */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH \ + (UINT32_C(0x2) << 0) + uint8_t auto_duplex; + + /* + * This value is used to configure the pause that will be used for + * autonegotiation. Add text on the usage of auto_pause and force_pause. + */ + /* + * When this bit is '1', Generation of tx pause messages has been + * requested. Disabled otherwise. + */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_TX UINT32_C(0x1) + /* + * When this bit is '1', Reception of rx pause messages has been + * requested. Disabled otherwise. + */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_RX UINT32_C(0x2) + /* + * When set to 1, the advertisement of pause is enabled. # When the + * auto_mode is not set to none and this flag is set to 1, then the + * auto_pause bits on this port are being advertised and autoneg pause + * results are being interpreted. # When the auto_mode is not set to + * none and this flag is set to 0, the pause is forced as indicated in + * force_pause, and also advertised as auto_pause bits, but the autoneg + * results are not interpreted since the pause configuration is being + * forced. # When the auto_mode is set to none and this flag is set to + * 1, auto_pause bits should be ignored and should be set to 0. + */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_AUTONEG_PAUSE UINT32_C(0x4) + uint8_t auto_pause; + + uint8_t unused_0; + + /* + * This is the speed that will be used if the autoneg_mode is + * "one_speed" or "one_or_below". If an unsupported speed is selected, + * an error will be generated. + */ + /* 100Mb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100MB \ + (UINT32_C(0x1) << 0) + /* 1Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_1GB \ + (UINT32_C(0xa) << 0) + /* 2Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2GB \ + (UINT32_C(0x14) << 0) + /* 2.5Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2_5GB \ + (UINT32_C(0x19) << 0) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10GB \ + (UINT32_C(0x64) << 0) + /* 20Mb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_20GB \ + (UINT32_C(0xc8) << 0) + /* 25Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_25GB \ + (UINT32_C(0xfa) << 0) + /* 40Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_40GB \ + (UINT32_C(0x190) << 0) + /* 50Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_50GB \ + (UINT32_C(0x1f4) << 0) + /* 100Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100GB \ + (UINT32_C(0x3e8) << 0) + /* 10Mb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10MB \ + (UINT32_C(0xffff) << 0) + uint16_t auto_link_speed; + + /* + * This is a mask of link speeds that will be used if autoneg_mode is + * "mask". If unsupported speed is enabled an error will be generated. + */ + /* 100Mb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MBHD \ + UINT32_C(0x1) + /* 100Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB \ + UINT32_C(0x2) + /* 1Gb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GBHD \ + UINT32_C(0x4) + /* 1Gb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB \ + UINT32_C(0x8) + /* 2Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2GB \ + UINT32_C(0x10) + /* 2.5Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB \ + UINT32_C(0x20) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB \ + UINT32_C(0x40) + /* 20Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB \ + UINT32_C(0x80) + /* 25Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB \ + UINT32_C(0x100) + /* 40Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB \ + UINT32_C(0x200) + /* 50Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB \ + UINT32_C(0x400) + /* 100Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100GB \ + UINT32_C(0x800) + /* 10Mb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MBHD \ + UINT32_C(0x1000) + /* 10Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MB \ + UINT32_C(0x2000) + uint16_t auto_link_speed_mask; + + /* This value controls the wirespeed feature. */ + /* Wirespeed feature is disabled. */ + #define HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_OFF (UINT32_C(0x0) << 0) + /* Wirespeed feature is enabled. */ + #define HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_ON (UINT32_C(0x1) << 0) + uint8_t wirespeed; + + /* This value controls the loopback setting for the PHY. */ + /* No loopback is selected. Normal operation. */ + #define HWRM_PORT_PHY_CFG_INPUT_LPBK_NONE (UINT32_C(0x0) << 0) + /* + * The HW will be configured with local loopback such that host + * data is sent back to the host without modification. + */ + #define HWRM_PORT_PHY_CFG_INPUT_LPBK_LOCAL (UINT32_C(0x1) << 0) + /* + * The HW will be configured with remote loopback such that port + * logic will send packets back out the transmitter that are + * received. + */ + #define HWRM_PORT_PHY_CFG_INPUT_LPBK_REMOTE (UINT32_C(0x2) << 0) + uint8_t lpbk; + + /* + * This value is used to configure the pause that will be used for force + * mode. + */ + /* + * When this bit is '1', Generation of tx pause messages is supported. + * Disabled otherwise. + */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_TX UINT32_C(0x1) + /* + * When this bit is '1', Reception of rx pause messages is supported. + * Disabled otherwise. + */ + #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_RX UINT32_C(0x2) + uint8_t force_pause; + + uint8_t unused_1; + + /* + * This value controls the pre-emphasis to be used for the link. Driver + * should not set this value (use enable.preemphasis = 0) unless driver + * is sure of setting. Normally HWRM FW will determine proper pre- + * emphasis. + */ + uint32_t preemphasis; + + /* + * Setting for link speed mask that is used to advertise speeds during + * autonegotiation when EEE is enabled. This field is valid only when + * EEE is enabled. The speeds specified in this field shall be a subset + * of speeds specified in auto_link_speed_mask. If EEE is enabled,then + * at least one speed shall be provided in this mask. + */ + /* Reserved */ + #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD1 UINT32_C(0x1) + /* 100Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_100MB UINT32_C(0x2) + /* Reserved */ + #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD2 UINT32_C(0x4) + /* 1Gb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_1GB UINT32_C(0x8) + /* Reserved */ + #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD3 \ + UINT32_C(0x10) + /* Reserved */ + #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD4 \ + UINT32_C(0x20) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_10GB \ + UINT32_C(0x40) + uint16_t eee_link_speed_mask; + + uint8_t unused_2; + uint8_t unused_3; + + /* + * Reuested setting of TX LPI timer in microseconds. This field is valid + * only when EEE is enabled and TX LPI is enabled. + */ + #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_MASK \ + UINT32_C(0xffffff) + #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_SFT 0 + uint32_t tx_lpi_timer; + + uint32_t unused_4; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_port_phy_cfg_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_port_phy_qcfg */ +/* Description: This command queries the PHY configuration for the port. */ +/* Input (24 bytes) */ + +struct hwrm_port_phy_qcfg_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* Port ID of port that is to be queried. */ + uint16_t port_id; + + uint16_t unused_0[3]; +} __attribute__((packed)); + +/* Output (96 bytes) */ +struct hwrm_port_phy_qcfg_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* This value indicates the current link status. */ + /* There is no link or cable detected. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_NO_LINK (UINT32_C(0x0) << 0) + /* There is no link, but a cable has been detected. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SIGNAL (UINT32_C(0x1) << 0) + /* There is a link. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LINK (UINT32_C(0x2) << 0) + uint8_t link; + + uint8_t unused_0; + + /* This value indicates the current link speed of the connection. */ + /* 100Mb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100MB \ + (UINT32_C(0x1) << 0) + /* 1Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_1GB \ + (UINT32_C(0xa) << 0) + /* 2Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2GB \ + (UINT32_C(0x14) << 0) + /* 2.5Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2_5GB \ + (UINT32_C(0x19) << 0) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10GB \ + (UINT32_C(0x64) << 0) + /* 20Mb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_20GB \ + (UINT32_C(0xc8) << 0) + /* 25Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_25GB \ + (UINT32_C(0xfa) << 0) + /* 40Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_40GB \ + (UINT32_C(0x190) << 0) + /* 50Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_50GB \ + (UINT32_C(0x1f4) << 0) + /* 100Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100GB \ + (UINT32_C(0x3e8) << 0) + /* 10Mb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10MB \ + (UINT32_C(0xffff) << 0) + uint16_t link_speed; + + /* This value is indicates the duplex of the current connection. */ + /* Half Duplex connection. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_HALF (UINT32_C(0x0) << 0) + /* Full duplex connection. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_FULL (UINT32_C(0x1) << 0) + uint8_t duplex; + + /* + * This value is used to indicate the current pause configuration. When + * autoneg is enabled, this value represents the autoneg results of + * pause configuration. + */ + /* + * When this bit is '1', Generation of tx pause messages is supported. + * Disabled otherwise. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_TX UINT32_C(0x1) + /* + * When this bit is '1', Reception of rx pause messages is supported. + * Disabled otherwise. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_RX UINT32_C(0x2) + uint8_t pause; + + /* + * The supported speeds for the port. This is a bit mask. For each speed + * that is supported, the corrresponding bit will be set to '1'. + */ + /* 100Mb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MBHD \ + UINT32_C(0x1) + /* 100Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MB \ + UINT32_C(0x2) + /* 1Gb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GBHD \ + UINT32_C(0x4) + /* 1Gb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GB \ + UINT32_C(0x8) + /* 2Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2GB \ + UINT32_C(0x10) + /* 2.5Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2_5GB \ + UINT32_C(0x20) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10GB \ + UINT32_C(0x40) + /* 20Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_20GB \ + UINT32_C(0x80) + /* 25Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_25GB \ + UINT32_C(0x100) + /* 40Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_40GB \ + UINT32_C(0x200) + /* 50Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_50GB \ + UINT32_C(0x400) + /* 100Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100GB \ + UINT32_C(0x800) + /* 10Mb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MBHD \ + UINT32_C(0x1000) + /* 10Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MB \ + UINT32_C(0x2000) + uint16_t support_speeds; + + /* + * Current setting of forced link speed. When the link speed is not + * being forced, this value shall be set to 0. + */ + /* 100Mb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100MB \ + (UINT32_C(0x1) << 0) + /* 1Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_1GB \ + (UINT32_C(0xa) << 0) + /* 2Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2GB \ + (UINT32_C(0x14) << 0) + /* 2.5Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2_5GB \ + (UINT32_C(0x19) << 0) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10GB \ + (UINT32_C(0x64) << 0) + /* 20Mb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_20GB \ + (UINT32_C(0xc8) << 0) + /* 25Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_25GB \ + (UINT32_C(0xfa) << 0) + /* 40Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_40GB \ + (UINT32_C(0x190) << 0) + /* 50Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_50GB \ + (UINT32_C(0x1f4) << 0) + /* 100Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100GB \ + (UINT32_C(0x3e8) << 0) + /* 10Mb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10MB \ + (UINT32_C(0xffff) << 0) + uint16_t force_link_speed; + + /* Current setting of auto negotiation mode. */ + /* + * Disable autoneg or autoneg disabled. No speeds are selected. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_NONE \ + (UINT32_C(0x0) << 0) + /* Select all possible speeds for autoneg mode. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ALL_SPEEDS \ + (UINT32_C(0x1) << 0) + /* + * Select only the auto_link_speed speed for autoneg mode. This + * mode has been DEPRECATED. An HWRM client should not use this + * mode. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_SPEED \ + (UINT32_C(0x2) << 0) + /* + * Select the auto_link_speed or any speed below that speed for + * autoneg. This mode has been DEPRECATED. An HWRM client should + * not use this mode. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_OR_BELOW \ + (UINT32_C(0x3) << 0) + /* + * Select the speeds based on the corresponding link speed mask + * value that is provided. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_SPEED_MASK \ + (UINT32_C(0x4) << 0) + uint8_t auto_mode; + + /* + * Current setting of pause autonegotiation. Move autoneg_pause flag + * here. + */ + /* + * When this bit is '1', Generation of tx pause messages has been + * requested. Disabled otherwise. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_TX UINT32_C(0x1) + /* + * When this bit is '1', Reception of rx pause messages has been + * requested. Disabled otherwise. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_RX UINT32_C(0x2) + /* + * When set to 1, the advertisement of pause is enabled. # When the + * auto_mode is not set to none and this flag is set to 1, then the + * auto_pause bits on this port are being advertised and autoneg pause + * results are being interpreted. # When the auto_mode is not set to + * none and this flag is set to 0, the pause is forced as indicated in + * force_pause, and also advertised as auto_pause bits, but the autoneg + * results are not interpreted since the pause configuration is being + * forced. # When the auto_mode is set to none and this flag is set to + * 1, auto_pause bits should be ignored and should be set to 0. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_AUTONEG_PAUSE \ + UINT32_C(0x4) + uint8_t auto_pause; + + /* + * Current setting for auto_link_speed. This field is only valid when + * auto_mode is set to "one_speed" or "one_or_below". + */ + /* 100Mb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100MB \ + (UINT32_C(0x1) << 0) + /* 1Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_1GB \ + (UINT32_C(0xa) << 0) + /* 2Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2GB \ + (UINT32_C(0x14) << 0) + /* 2.5Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2_5GB \ + (UINT32_C(0x19) << 0) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10GB \ + (UINT32_C(0x64) << 0) + /* 20Mb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_20GB \ + (UINT32_C(0xc8) << 0) + /* 25Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_25GB \ + (UINT32_C(0xfa) << 0) + /* 40Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_40GB \ + (UINT32_C(0x190) << 0) + /* 50Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_50GB \ + (UINT32_C(0x1f4) << 0) + /* 100Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100GB \ + (UINT32_C(0x3e8) << 0) + /* 10Mb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10MB \ + (UINT32_C(0xffff) << 0) + uint16_t auto_link_speed; + + /* + * Current setting for auto_link_speed_mask that is used to advertise + * speeds during autonegotiation. This field is only valid when + * auto_mode is set to "mask". The speeds specified in this field shall + * be a subset of supported speeds on this port. + */ + /* 100Mb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MBHD \ + UINT32_C(0x1) + /* 100Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MB \ + UINT32_C(0x2) + /* 1Gb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GBHD \ + UINT32_C(0x4) + /* 1Gb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GB \ + UINT32_C(0x8) + /* 2Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2GB \ + UINT32_C(0x10) + /* 2.5Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2_5GB \ + UINT32_C(0x20) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10GB \ + UINT32_C(0x40) + /* 20Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_20GB \ + UINT32_C(0x80) + /* 25Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_25GB \ + UINT32_C(0x100) + /* 40Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_40GB \ + UINT32_C(0x200) + /* 50Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_50GB \ + UINT32_C(0x400) + /* 100Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100GB \ + UINT32_C(0x800) + /* 10Mb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MBHD \ + UINT32_C(0x1000) + /* 10Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MB \ + UINT32_C(0x2000) + uint16_t auto_link_speed_mask; + + /* Current setting for wirespeed. */ + /* Wirespeed feature is disabled. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_WIRESPEED_OFF (UINT32_C(0x0) << 0) + /* Wirespeed feature is enabled. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_WIRESPEED_ON (UINT32_C(0x1) << 0) + uint8_t wirespeed; + + /* Current setting for loopback. */ + /* No loopback is selected. Normal operation. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_NONE (UINT32_C(0x0) << 0) + /* + * The HW will be configured with local loopback such that host + * data is sent back to the host without modification. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_LOCAL (UINT32_C(0x1) << 0) + /* + * The HW will be configured with remote loopback such that port + * logic will send packets back out the transmitter that are + * received. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_REMOTE (UINT32_C(0x2) << 0) + uint8_t lpbk; + + /* + * Current setting of forced pause. When the pause configuration is not + * being forced, then this value shall be set to 0. + */ + /* + * When this bit is '1', Generation of tx pause messages is supported. + * Disabled otherwise. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_TX \ + UINT32_C(0x1) + /* + * When this bit is '1', Reception of rx pause messages is supported. + * Disabled otherwise. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_RX \ + UINT32_C(0x2) + uint8_t force_pause; + + /* + * This value indicates the current status of the optics module on this + * port. + */ + /* Module is inserted and accepted */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NONE \ + (UINT32_C(0x0) << 0) + /* Module is rejected and transmit side Laser is disabled. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_DISABLETX \ + (UINT32_C(0x1) << 0) + /* Module mismatch warning. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_WARNINGMSG \ + (UINT32_C(0x2) << 0) + /* Module is rejected and powered down. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_PWRDOWN \ + (UINT32_C(0x3) << 0) + /* Module is not inserted. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTINSERTED \ + (UINT32_C(0x4) << 0) + /* Module status is not applicable. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTAPPLICABLE \ + (UINT32_C(0xff) << 0) + uint8_t module_status; + + /* Current setting for preemphasis. */ + uint32_t preemphasis; + + /* This field represents the major version of the PHY. */ + uint8_t phy_maj; + + /* This field represents the minor version of the PHY. */ + uint8_t phy_min; + + /* This field represents the build version of the PHY. */ + uint8_t phy_bld; + + /* This value represents a PHY type. */ + /* Unknown */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_UNKNOWN \ + (UINT32_C(0x0) << 0) + /* BASE-CR */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASECR \ + (UINT32_C(0x1) << 0) + /* BASE-KR4 (Deprecated) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR4 \ + (UINT32_C(0x2) << 0) + /* BASE-LR */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASELR \ + (UINT32_C(0x3) << 0) + /* BASE-SR */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASESR \ + (UINT32_C(0x4) << 0) + /* BASE-KR2 (Deprecated) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR2 \ + (UINT32_C(0x5) << 0) + /* BASE-KX */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKX \ + (UINT32_C(0x6) << 0) + /* BASE-KR */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR \ + (UINT32_C(0x7) << 0) + /* BASE-T */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASET \ + (UINT32_C(0x8) << 0) + /* EEE capable BASE-T */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASETE \ + (UINT32_C(0x9) << 0) + /* SGMII connected external PHY */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_SGMIIEXTPHY \ + (UINT32_C(0xa) << 0) + uint8_t phy_type; + + /* This value represents a media type. */ + /* Unknown */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_UNKNOWN \ + (UINT32_C(0x0) << 0) + /* Twisted Pair */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_TP (UINT32_C(0x1) << 0) + /* Direct Attached Copper */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_DAC \ + (UINT32_C(0x2) << 0) + /* Fiber */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_FIBRE \ + (UINT32_C(0x3) << 0) + uint8_t media_type; + + /* This value represents a transceiver type. */ + /* PHY and MAC are in the same package */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_INTERNAL \ + (UINT32_C(0x1) << 0) + /* PHY and MAC are in different packages */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_EXTERNAL \ + (UINT32_C(0x2) << 0) + uint8_t xcvr_pkg_type; + + /* + * This field represents flags related to EEE configuration. These EEE + * configuration flags are valid only when the auto_mode is not set to + * none (in other words autonegotiation is enabled). + */ + /* This field represents PHY address. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_MASK UINT32_C(0x1f) + #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_SFT 0 + /* + * When set to 1, Energy Efficient Ethernet (EEE) mode is enabled. + * Speeds for autoneg with EEE mode enabled are based on + * eee_link_speed_mask. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ENABLED \ + UINT32_C(0x20) + /* + * This flag is valid only when eee_enabled is set to 1. # If + * eee_enabled is set to 0, then EEE mode is disabled and this flag + * shall be ignored. # If eee_enabled is set to 1 and this flag is set + * to 1, then Energy Efficient Ethernet (EEE) mode is enabled and in + * use. # If eee_enabled is set to 1 and this flag is set to 0, then + * Energy Efficient Ethernet (EEE) mode is enabled but is currently not + * in use. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ACTIVE \ + UINT32_C(0x40) + /* + * This flag is valid only when eee_enabled is set to 1. # If + * eee_enabled is set to 0, then EEE mode is disabled and this flag + * shall be ignored. # If eee_enabled is set to 1 and this flag is set + * to 1, then Energy Efficient Ethernet (EEE) mode is enabled and TX LPI + * is enabled. # If eee_enabled is set to 1 and this flag is set to 0, + * then Energy Efficient Ethernet (EEE) mode is enabled but TX LPI is + * disabled. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_TX_LPI \ + UINT32_C(0x80) + /* + * This field represents flags related to EEE configuration. These EEE + * configuration flags are valid only when the auto_mode is not set to + * none (in other words autonegotiation is enabled). + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_MASK \ + UINT32_C(0xe0) + #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_SFT 5 + uint8_t eee_config_phy_addr; + + /* Reserved field, set to 0 */ + /* + * When set to 1, the parallel detection is used to determine the speed + * of the link partner. Parallel detection is used when a + * autonegotiation capable device is connected to a link parter that is + * not capable of autonegotiation. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_PARALLEL_DETECT \ + UINT32_C(0x1) + /* Reserved field, set to 0 */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_MASK UINT32_C(0xfe) + #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_SFT 1 + uint8_t parallel_detect; + + /* + * The advertised speeds for the port by the link partner. Each + * advertised speed will be set to '1'. + */ + /* 100Mb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MBHD \ + UINT32_C(0x1) + /* 100Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MB \ + UINT32_C(0x2) + /* 1Gb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GBHD \ + UINT32_C(0x4) + /* 1Gb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GB \ + UINT32_C(0x8) + /* 2Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2GB \ + UINT32_C(0x10) + /* 2.5Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2_5GB \ + UINT32_C(0x20) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10GB \ + UINT32_C(0x40) + /* 20Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_20GB \ + UINT32_C(0x80) + /* 25Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_25GB \ + UINT32_C(0x100) + /* 40Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_40GB \ + UINT32_C(0x200) + /* 50Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_50GB \ + UINT32_C(0x400) + /* 100Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100GB \ + UINT32_C(0x800) + /* 10Mb link speed (Half-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MBHD \ + UINT32_C(0x1000) + /* 10Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MB \ + UINT32_C(0x2000) + uint16_t link_partner_adv_speeds; + + /* + * The advertised autoneg for the port by the link partner. This field + * is deprecated and should be set to 0. + */ + /* + * Disable autoneg or autoneg disabled. No speeds are selected. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_NONE \ + (UINT32_C(0x0) << 0) + /* Select all possible speeds for autoneg mode. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ALL_SPEEDS\ + (UINT32_C(0x1) << 0) + /* + * Select only the auto_link_speed speed for autoneg mode. This + * mode has been DEPRECATED. An HWRM client should not use this + * mode. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_SPEED \ + (UINT32_C(0x2) << 0) + /* + * Select the auto_link_speed or any speed below that speed for + * autoneg. This mode has been DEPRECATED. An HWRM client should + * not use this mode. + */ + #define \ + HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_OR_BELOW \ + (UINT32_C(0x3) << 0) + /* + * Select the speeds based on the corresponding link speed mask + * value that is provided. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK\ + (UINT32_C(0x4) << 0) + uint8_t link_partner_adv_auto_mode; + + /* The advertised pause settings on the port by the link partner. */ + /* + * When this bit is '1', Generation of tx pause messages is supported. + * Disabled otherwise. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_TX \ + UINT32_C(0x1) + /* + * When this bit is '1', Reception of rx pause messages is supported. + * Disabled otherwise. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_RX \ + UINT32_C(0x2) + uint8_t link_partner_adv_pause; + + /* + * Current setting for link speed mask that is used to advertise speeds + * during autonegotiation when EEE is enabled. This field is valid only + * when eee_enabled flags is set to 1. The speeds specified in this + * field shall be a subset of speeds specified in auto_link_speed_mask. + */ + /* Reserved */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD1 \ + UINT32_C(0x1) + /* 100Mb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_100MB \ + UINT32_C(0x2) + /* Reserved */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD2 \ + UINT32_C(0x4) + /* 1Gb link speed (Full-duplex) */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_1GB \ + UINT32_C(0x8) + /* Reserved */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD3 \ + UINT32_C(0x10) + /* Reserved */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD4 \ + UINT32_C(0x20) + /* 10Gb link speed */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_10GB \ + UINT32_C(0x40) + uint16_t adv_eee_link_speed_mask; + + /* + * Current setting for link speed mask that is advertised by the link + * partner when EEE is enabled. This field is valid only when + * eee_enabled flags is set to 1. + */ + /* Reserved */ + #define \ + HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD1 \ + UINT32_C(0x1) + /* 100Mb link speed (Full-duplex) */ + #define \ + HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_100MB \ + UINT32_C(0x2) + /* Reserved */ + #define \ + HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD2 \ + UINT32_C(0x4) + /* 1Gb link speed (Full-duplex) */ + #define \ + HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_1GB \ + UINT32_C(0x8) + /* Reserved */ + #define \ + HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD3 \ + UINT32_C(0x10) + /* Reserved */ + #define \ + HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD4 \ + UINT32_C(0x20) + /* 10Gb link speed */ + #define \ + HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_10GB \ + UINT32_C(0x40) + uint16_t link_partner_adv_eee_link_speed_mask; + + /* This value represents transceiver identifier type. */ + /* + * Current setting of TX LPI timer in microseconds. This field is valid + * only when_eee_enabled flag is set to 1 and tx_lpi_enabled is set to + * 1. + */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_MASK \ + UINT32_C(0xffffff) + #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_SFT 0 + /* This value represents transceiver identifier type. */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_MASK \ + UINT32_C(0xff000000) + #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFT \ + 24 + /* Unknown */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_UNKNOWN \ + (UINT32_C(0x0) << 24) + /* SFP/SFP+/SFP28 */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFP \ + (UINT32_C(0x3) << 24) + /* QSFP */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP \ + (UINT32_C(0xc) << 24) + /* QSFP+ */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFPPLUS \ + (UINT32_C(0xd) << 24) + /* QSFP28 */ + #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28 \ + (UINT32_C(0x11) << 24) + uint32_t xcvr_identifier_type_tx_lpi_timer; + + uint32_t unused_1; + + /* + * Up to 16 bytes of null padded ASCII string representing PHY vendor. + * If the string is set to null, then the vendor name is not available. + */ + char phy_vendor_name[16]; + + /* + * Up to 16 bytes of null padded ASCII string that identifies vendor + * specific part number of the PHY. If the string is set to null, then + * the vendor specific part number is not available. + */ + char phy_vendor_partnumber[16]; + + uint32_t unused_2; + uint8_t unused_3; + uint8_t unused_4; + uint8_t unused_5; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_ver_get */ +/* + * Description: This function is called by a driver to determine the HWRM + * interface version supported by the HWRM firmware, the version of HWRM + * firmware implementation, the name of HWRM firmware, the versions of other + * embedded firmwares, and the names of other embedded firmwares, etc. Any + * interface or firmware version with major = 0, minor = 0, and update = 0 shall + * be considered an invalid version. + */ + +/* Input (24 bytes) */ +struct hwrm_ver_get_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * This field represents the major version of HWRM interface + * specification supported by the driver HWRM implementation. The + * interface major version is intended to change only when non backward + * compatible changes are made to the HWRM interface specification. + */ + uint8_t hwrm_intf_maj; + + /* + * This field represents the minor version of HWRM interface + * specification supported by the driver HWRM implementation. A change + * in interface minor version is used to reflect significant backward + * compatible modification to HWRM interface specification. This can be + * due to addition or removal of functionality. HWRM interface + * specifications with the same major version but different minor + * versions are compatible. + */ + uint8_t hwrm_intf_min; + + /* + * This field represents the update version of HWRM interface + * specification supported by the driver HWRM implementation. The + * interface update version is used to reflect minor changes or bug + * fixes to a released HWRM interface specification. + */ + uint8_t hwrm_intf_upd; + + uint8_t unused_0[5]; +} __attribute__((packed)); + +/* Output (128 bytes) */ +struct hwrm_ver_get_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* + * This field represents the major version of HWRM interface + * specification supported by the HWRM implementation. The interface + * major version is intended to change only when non backward compatible + * changes are made to the HWRM interface specification. A HWRM + * implementation that is compliant with this specification shall + * provide value of 1 in this field. + */ + uint8_t hwrm_intf_maj; + + /* + * This field represents the minor version of HWRM interface + * specification supported by the HWRM implementation. A change in + * interface minor version is used to reflect significant backward + * compatible modification to HWRM interface specification. This can be + * due to addition or removal of functionality. HWRM interface + * specifications with the same major version but different minor + * versions are compatible. A HWRM implementation that is compliant with + * this specification shall provide value of 0 in this field. + */ + uint8_t hwrm_intf_min; + + /* + * This field represents the update version of HWRM interface + * specification supported by the HWRM implementation. The interface + * update version is used to reflect minor changes or bug fixes to a + * released HWRM interface specification. A HWRM implementation that is + * compliant with this specification shall provide value of 1 in this + * field. + */ + uint8_t hwrm_intf_upd; + + uint8_t hwrm_intf_rsvd; + + /* + * This field represents the major version of HWRM firmware. A change in + * firmware major version represents a major firmware release. + */ + uint8_t hwrm_fw_maj; + + /* + * This field represents the minor version of HWRM firmware. A change in + * firmware minor version represents significant firmware functionality + * changes. + */ + uint8_t hwrm_fw_min; + + /* + * This field represents the build version of HWRM firmware. A change in + * firmware build version represents bug fixes to a released firmware. + */ + uint8_t hwrm_fw_bld; + + /* + * This field is a reserved field. This field can be used to represent + * firmware branches or customer specific releases tied to a specific + * (major,minor,update) version of the HWRM firmware. + */ + uint8_t hwrm_fw_rsvd; + + /* + * This field represents the major version of mgmt firmware. A change in + * major version represents a major release. + */ + uint8_t mgmt_fw_maj; + + /* + * This field represents the minor version of mgmt firmware. A change in + * minor version represents significant functionality changes. + */ + uint8_t mgmt_fw_min; + + /* + * This field represents the build version of mgmt firmware. A change in + * update version represents bug fixes. + */ + uint8_t mgmt_fw_bld; + + /* + * This field is a reserved field. This field can be used to represent + * firmware branches or customer specific releases tied to a specific + * (major,minor,update) version + */ + uint8_t mgmt_fw_rsvd; + + /* + * This field represents the major version of network control firmware. + * A change in major version represents a major release. + */ + uint8_t netctrl_fw_maj; + + /* + * This field represents the minor version of network control firmware. + * A change in minor version represents significant functionality + * changes. + */ + uint8_t netctrl_fw_min; + + /* + * This field represents the build version of network control firmware. + * A change in update version represents bug fixes. + */ + uint8_t netctrl_fw_bld; + + /* + * This field is a reserved field. This field can be used to represent + * firmware branches or customer specific releases tied to a specific + * (major,minor,update) version + */ + uint8_t netctrl_fw_rsvd; + + /* + * This field is reserved for future use. The responder should set it to + * 0. The requester should ignore this field. + */ + uint32_t reserved1; + + /* + * This field represents the major version of RoCE firmware. A change in + * major version represents a major release. + */ + uint8_t roce_fw_maj; + + /* + * This field represents the minor version of RoCE firmware. A change in + * minor version represents significant functionality changes. + */ + uint8_t roce_fw_min; + + /* + * This field represents the build version of RoCE firmware. A change in + * update version represents bug fixes. + */ + uint8_t roce_fw_bld; + + /* + * This field is a reserved field. This field can be used to represent + * firmware branches or customer specific releases tied to a specific + * (major,minor,update) version + */ + uint8_t roce_fw_rsvd; + + /* + * This field represents the name of HWRM FW (ASCII chars without NULL + * at the end). + */ + char hwrm_fw_name[16]; + + /* + * This field represents the name of mgmt FW (ASCII chars without NULL + * at the end). + */ + char mgmt_fw_name[16]; + + /* + * This field represents the name of network control firmware (ASCII + * chars without NULL at the end). + */ + char netctrl_fw_name[16]; + + /* + * This field is reserved for future use. The responder should set it to + * 0. The requester should ignore this field. + */ + uint32_t reserved2[4]; + + /* + * This field represents the name of RoCE FW (ASCII chars without NULL + * at the end). + */ + char roce_fw_name[16]; + + /* This field returns the chip number. */ + uint16_t chip_num; + + /* This field returns the revision of chip. */ + uint8_t chip_rev; + + /* This field returns the chip metal number. */ + uint8_t chip_metal; + + /* This field returns the bond id of the chip. */ + uint8_t chip_bond_id; + + /* + * This value indicates the type of platform used for chip + * implementation. + */ + /* ASIC */ + #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_ASIC \ + (UINT32_C(0x0) << 0) + /* FPGA platform of the chip. */ + #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_FPGA \ + (UINT32_C(0x1) << 0) + /* Palladium platform of the chip. */ + #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_PALLADIUM \ + (UINT32_C(0x2) << 0) + uint8_t chip_platform_type; + + /* + * This field returns the maximum value of request window that is + * supported by the HWRM. The request window is mapped into device + * address space using MMIO. + */ + uint16_t max_req_win_len; + + /* + * This field returns the maximum value of response buffer in bytes. If + * a request specifies the response buffer length that is greater than + * this value, then the HWRM should fail it. The value of this field + * shall be 4KB or more. + */ + uint16_t max_resp_len; + + /* + * This field returns the default request timeout value in milliseconds. + */ + uint16_t def_req_timeout; + + uint8_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_queue_qportcfg */ +/* + * Description: This function is called by a driver to query queue configuration + * of a port. # The HWRM shall at least advertise one queue with lossy service + * profile. # The driver shall use this command to query queue ids before + * configuring or using any queues. # If a service profile is not set for a + * queue, then the driver shall not use that queue without configuring a service + * profile for it. # If the driver is not allowed to configure service profiles, + * then the driver shall only use queues for which service profiles are pre- + * configured. + */ + +/* Input (24 bytes) */ +struct hwrm_queue_qportcfg_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * Enumeration denoting the RX, TX type of the resource. This + * enumeration is used for resources that are similar for both TX and RX + * paths of the chip. + */ + #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH \ + UINT32_C(0x1) + /* tx path */ + #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_TX \ + (UINT32_C(0x0) << 0) + /* rx path */ + #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX \ + (UINT32_C(0x1) << 0) + #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_LAST \ + HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX + uint32_t flags; + + /* + * Port ID of port for which the queue configuration is being queried. + * This field is only required when sent by IPC. + */ + uint16_t port_id; + + uint16_t unused_0; +} __attribute__((packed)); + +/* hwrm_ring_alloc */ +/* + * Description: This command allocates and does basic preparation for a ring. + */ + +/* Input (80 bytes) */ +struct hwrm_ring_alloc_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* This bit must be '1' for the Reserved1 field to be configured. */ + #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED1 UINT32_C(0x1) + /* This bit must be '1' for the Reserved2 field to be configured. */ + #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED2 UINT32_C(0x2) + /* This bit must be '1' for the Reserved3 field to be configured. */ + #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED3 UINT32_C(0x4) + /* + * This bit must be '1' for the stat_ctx_id_valid field to be + * configured. + */ + #define HWRM_RING_ALLOC_INPUT_ENABLES_STAT_CTX_ID_VALID UINT32_C(0x8) + /* This bit must be '1' for the Reserved4 field to be configured. */ + #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED4 UINT32_C(0x10) + /* This bit must be '1' for the max_bw_valid field to be configured. */ + #define HWRM_RING_ALLOC_INPUT_ENABLES_MAX_BW_VALID UINT32_C(0x20) + uint32_t enables; + + /* Ring Type. */ + /* Completion Ring (CR) */ + #define HWRM_RING_ALLOC_INPUT_RING_TYPE_CMPL (UINT32_C(0x0) << 0) + /* TX Ring (TR) */ + #define HWRM_RING_ALLOC_INPUT_RING_TYPE_TX (UINT32_C(0x1) << 0) + /* RX Ring (RR) */ + #define HWRM_RING_ALLOC_INPUT_RING_TYPE_RX (UINT32_C(0x2) << 0) + uint8_t ring_type; + + uint8_t unused_0; + uint16_t unused_1; + + /* This value is a pointer to the page table for the Ring. */ + uint64_t page_tbl_addr; + + /* First Byte Offset of the first entry in the first page. */ + uint32_t fbo; + + /* + * Actual page size in 2^page_size. The supported range is increments in + * powers of 2 from 16 bytes to 1GB. - 4 = 16 B Page size is 16 B. - 12 + * = 4 KB Page size is 4 KB. - 13 = 8 KB Page size is 8 KB. - 16 = 64 KB + * Page size is 64 KB. - 22 = 2 MB Page size is 2 MB. - 23 = 4 MB Page + * size is 4 MB. - 31 = 1 GB Page size is 1 GB. + */ + uint8_t page_size; + + /* + * This value indicates the depth of page table. For this version of the + * specification, value other than 0 or 1 shall be considered as an + * invalid value. When the page_tbl_depth = 0, then it is treated as a + * special case with the following. 1. FBO and page size fields are not + * valid. 2. page_tbl_addr is the physical address of the first element + * of the ring. + */ + uint8_t page_tbl_depth; + + uint8_t unused_2; + uint8_t unused_3; + + /* + * Number of 16B units in the ring. Minimum size for a ring is 16 16B + * entries. + */ + uint32_t length; + + /* + * Logical ring number for the ring to be allocated. This value + * determines the position in the doorbell area where the update to the + * ring will be made. For completion rings, this value is also the MSI-X + * vector number for the function the completion ring is associated + * with. + */ + uint16_t logical_id; + + /* + * This field is used only when ring_type is a TX ring. This value + * indicates what completion ring the TX ring is associated with. + */ + uint16_t cmpl_ring_id; + + /* + * This field is used only when ring_type is a TX ring. This value + * indicates what CoS queue the TX ring is associated with. + */ + uint16_t queue_id; + + uint8_t unused_4; + uint8_t unused_5; + + /* This field is reserved for the future use. It shall be set to 0. */ + uint32_t reserved1; + /* This field is reserved for the future use. It shall be set to 0. */ + uint16_t reserved2; + + uint8_t unused_6; + uint8_t unused_7; + /* This field is reserved for the future use. It shall be set to 0. */ + uint32_t reserved3; + + /* + * This field is used only when ring_type is a TX ring. This input + * indicates what statistics context this ring should be associated + * with. + */ + uint32_t stat_ctx_id; + + /* This field is reserved for the future use. It shall be set to 0. */ + uint32_t reserved4; + + /* + * This field is used only when ring_type is a TX ring. Maximum BW + * allocated to this TX ring in Mbps. The HWRM will translate this value + * into byte counter and time interval used for this ring inside the + * device. + */ + uint32_t max_bw; + + /* + * This field is used only when ring_type is a Completion ring. This + * value indicates what interrupt mode should be used on this completion + * ring. Note: In the legacy interrupt mode, no more than 16 completion + * rings are allowed. + */ + /* Legacy INTA */ + #define HWRM_RING_ALLOC_INPUT_INT_MODE_LEGACY (UINT32_C(0x0) << 0) + /* Reserved */ + #define HWRM_RING_ALLOC_INPUT_INT_MODE_RSVD (UINT32_C(0x1) << 0) + /* MSI-X */ + #define HWRM_RING_ALLOC_INPUT_INT_MODE_MSIX (UINT32_C(0x2) << 0) + /* No Interrupt - Polled mode */ + #define HWRM_RING_ALLOC_INPUT_INT_MODE_POLL (UINT32_C(0x3) << 0) + uint8_t int_mode; + + uint8_t unused_8[3]; +} __attribute__((packed)); + +/* Output (16 bytes) */ + +struct hwrm_ring_alloc_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* Physical number of ring allocated. */ + uint16_t ring_id; + + /* Logical number of ring allocated. */ + uint16_t logical_ring_id; + + uint8_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_ring_free */ +/* + * Description: This command is used to free a ring and associated resources. + */ +/* Input (24 bytes) */ + +struct hwrm_ring_free_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* Ring Type. */ + /* Completion Ring (CR) */ + #define HWRM_RING_FREE_INPUT_RING_TYPE_CMPL (UINT32_C(0x0) << 0) + /* TX Ring (TR) */ + #define HWRM_RING_FREE_INPUT_RING_TYPE_TX (UINT32_C(0x1) << 0) + /* RX Ring (RR) */ + #define HWRM_RING_FREE_INPUT_RING_TYPE_RX (UINT32_C(0x2) << 0) + uint8_t ring_type; + + uint8_t unused_0; + + /* Physical number of ring allocated. */ + uint16_t ring_id; + + uint32_t unused_1; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_ring_free_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_ring_grp_alloc */ +/* + * Description: This API allocates and does basic preparation for a ring group. + */ + +/* Input (24 bytes) */ +struct hwrm_ring_grp_alloc_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* This value identifies the CR associated with the ring group. */ + uint16_t cr; + + /* This value identifies the main RR associated with the ring group. */ + uint16_t rr; + + /* + * This value identifies the aggregation RR associated with the ring + * group. If this value is 0xFF... (All Fs), then no Aggregation ring + * will be set. + */ + uint16_t ar; + + /* + * This value identifies the statistics context associated with the ring + * group. + */ + uint16_t sc; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_ring_grp_alloc_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* + * This is the ring group ID value. Use this value to program the + * default ring group for the VNIC or as table entries in an RSS/COS + * context. + */ + uint32_t ring_group_id; + + uint8_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_ring_grp_free */ +/* + * Description: This API frees a ring group and associated resources. # If a + * ring in the ring group is reset or free, then the associated rings in the + * ring group shall also be reset/free using hwrm_ring_free. # A function driver + * shall always use hwrm_ring_grp_free after freeing all rings in a group. # As + * a part of executing this command, the HWRM shall reset all associated ring + * group resources. + */ + +/* Input (24 bytes) */ +struct hwrm_ring_grp_free_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* This is the ring group ID value. */ + uint32_t ring_group_id; + + uint32_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_ring_grp_free_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_stat_ctx_alloc */ +/* + * Description: This command allocates and does basic preparation for a stat + * context. + */ + +/* Input (32 bytes) */ +struct hwrm_stat_ctx_alloc_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* This is the address for statistic block. */ + uint64_t stats_dma_addr; + + /* + * The statistic block update period in ms. e.g. 250ms, 500ms, 750ms, + * 1000ms. + */ + uint32_t update_period_ms; + + uint32_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_stat_ctx_alloc_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* This is the statistics context ID value. */ + uint32_t stat_ctx_id; + + uint8_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_stat_ctx_clr_stats */ +/* Description: This command clears statistics of a context. */ + +/* Input (24 bytes) */ +struct hwrm_stat_ctx_clr_stats_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* ID of the statistics context that is being queried. */ + uint32_t stat_ctx_id; + + uint32_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_stat_ctx_clr_stats_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_stat_ctx_free */ +/* Description: This command is used to free a stat context. */ +/* Input (24 bytes) */ + +struct hwrm_stat_ctx_free_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* ID of the statistics context that is being queried. */ + uint32_t stat_ctx_id; + + uint32_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ + +struct hwrm_stat_ctx_free_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* This is the statistics context ID value. */ + uint32_t stat_ctx_id; + + uint8_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_vnic_alloc */ +/* + * Description: This VNIC is a resource in the RX side of the chip that is used + * to represent a virtual host "interface". # At the time of VNIC allocation or + * configuration, the function can specify whether it wants the requested VNIC + * to be the default VNIC for the function or not. # If a function requests + * allocation of a VNIC for the first time and a VNIC is successfully allocated + * by the HWRM, then the HWRM shall make the allocated VNIC as the default VNIC + * for that function. # The default VNIC shall be used for the default action + * for a partition or function. # For each VNIC allocated on a function, a + * mapping on the RX side to map the allocated VNIC to source virtual interface + * shall be performed by the HWRM. This should be hidden to the function driver + * requesting the VNIC allocation. This enables broadcast/multicast replication + * with source knockout. # If multicast replication with source knockout is + * enabled, then the internal VNIC to SVIF mapping data structures shall be + * programmed at the time of VNIC allocation. + */ + +/* Input (24 bytes) */ +struct hwrm_vnic_alloc_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * When this bit is '1', this VNIC is requested to be the default VNIC + * for this function. + */ + #define HWRM_VNIC_ALLOC_INPUT_FLAGS_DEFAULT UINT32_C(0x1) + uint32_t flags; + + uint32_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_vnic_alloc_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* Logical vnic ID */ + uint32_t vnic_id; + + uint8_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_vnic_cfg */ +/* Description: Configure the RX VNIC structure. */ + +/* Input (40 bytes) */ +struct hwrm_vnic_cfg_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * When this bit is '1', the VNIC is requested to be the default VNIC + * for the function. + */ + #define HWRM_VNIC_CFG_INPUT_FLAGS_DEFAULT UINT32_C(0x1) + /* + * When this bit is '1', the VNIC is being configured to strip VLAN in + * the RX path. If set to '0', then VLAN stripping is disabled on this + * VNIC. + */ + #define HWRM_VNIC_CFG_INPUT_FLAGS_VLAN_STRIP_MODE UINT32_C(0x2) + /* + * When this bit is '1', the VNIC is being configured to buffer receive + * packets in the hardware until the host posts new receive buffers. If + * set to '0', then bd_stall is being configured to be disabled on this + * VNIC. + */ + #define HWRM_VNIC_CFG_INPUT_FLAGS_BD_STALL_MODE UINT32_C(0x4) + /* + * When this bit is '1', the VNIC is being configured to receive both + * RoCE and non-RoCE traffic. If set to '0', then this VNIC is not + * configured to be operating in dual VNIC mode. + */ + #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_DUAL_VNIC_MODE UINT32_C(0x8) + /* + * When this flag is set to '1', the VNIC is requested to be configured + * to receive only RoCE traffic. If this flag is set to '0', then this + * flag shall be ignored by the HWRM. If roce_dual_vnic_mode flag is set + * to '1', then the HWRM client shall not set this flag to '1'. + */ + #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_ONLY_VNIC_MODE UINT32_C(0x10) + uint32_t flags; + + /* This bit must be '1' for the dflt_ring_grp field to be configured. */ + #define HWRM_VNIC_CFG_INPUT_ENABLES_DFLT_RING_GRP UINT32_C(0x1) + /* This bit must be '1' for the rss_rule field to be configured. */ + #define HWRM_VNIC_CFG_INPUT_ENABLES_RSS_RULE UINT32_C(0x2) + /* This bit must be '1' for the cos_rule field to be configured. */ + #define HWRM_VNIC_CFG_INPUT_ENABLES_COS_RULE UINT32_C(0x4) + /* This bit must be '1' for the lb_rule field to be configured. */ + #define HWRM_VNIC_CFG_INPUT_ENABLES_LB_RULE UINT32_C(0x8) + /* This bit must be '1' for the mru field to be configured. */ + #define HWRM_VNIC_CFG_INPUT_ENABLES_MRU UINT32_C(0x10) + uint32_t enables; + + /* Logical vnic ID */ + uint16_t vnic_id; + + /* + * Default Completion ring for the VNIC. This ring will be chosen if + * packet does not match any RSS rules and if there is no COS rule. + */ + uint16_t dflt_ring_grp; + + /* + * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if there is no + * RSS rule. + */ + uint16_t rss_rule; + + /* + * RSS ID for COS rule/table structure. 0xFF... (All Fs) if there is no + * COS rule. + */ + uint16_t cos_rule; + + /* + * RSS ID for load balancing rule/table structure. 0xFF... (All Fs) if + * there is no LB rule. + */ + uint16_t lb_rule; + + /* + * The maximum receive unit of the vnic. Each vnic is associated with a + * function. The vnic mru value overwrites the mru setting of the + * associated function. The HWRM shall make sure that vnic mru does not + * exceed the mru of the port the function is associated with. + */ + uint16_t mru; + + uint32_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_vnic_cfg_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_vnic_free */ +/* + * Description: Free a VNIC resource. Idle any resources associated with the + * VNIC as well as the VNIC. Reset and release all resources associated with the + * VNIC. + */ + +/* Input (24 bytes) */ +struct hwrm_vnic_free_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* Logical vnic ID */ + uint32_t vnic_id; + + uint32_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_vnic_free_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_vnic_rss_cfg */ +/* Description: This function is used to enable RSS configuration. */ + +/* Input (48 bytes) */ +struct hwrm_vnic_rss_cfg_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * When this bit is '1', the RSS hash shall be computed over source and + * destination IPv4 addresses of IPv4 packets. + */ + #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV4 UINT32_C(0x1) + /* + * When this bit is '1', the RSS hash shall be computed over + * source/destination IPv4 addresses and source/destination ports of + * TCP/IPv4 packets. + */ + #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV4 UINT32_C(0x2) + /* + * When this bit is '1', the RSS hash shall be computed over + * source/destination IPv4 addresses and source/destination ports of + * UDP/IPv4 packets. + */ + #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV4 UINT32_C(0x4) + /* + * When this bit is '1', the RSS hash shall be computed over source and + * destination IPv4 addresses of IPv6 packets. + */ + #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV6 UINT32_C(0x8) + /* + * When this bit is '1', the RSS hash shall be computed over + * source/destination IPv6 addresses and source/destination ports of + * TCP/IPv6 packets. + */ + #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV6 UINT32_C(0x10) + /* + * When this bit is '1', the RSS hash shall be computed over + * source/destination IPv6 addresses and source/destination ports of + * UDP/IPv6 packets. + */ + #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV6 UINT32_C(0x20) + uint32_t hash_type; + + uint32_t unused_0; + + /* This is the address for rss ring group table */ + uint64_t ring_grp_tbl_addr; + + /* This is the address for rss hash key table */ + uint64_t hash_key_tbl_addr; + + /* Index to the rss indirection table. */ + uint16_t rss_ctx_idx; + + uint16_t unused_1[3]; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_vnic_rss_cfg_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* Input (16 bytes) */ +struct hwrm_vnic_rss_cos_lb_ctx_alloc_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; +} __attribute__((packed)); + +/* Output (16 bytes) */ + +struct hwrm_vnic_rss_cos_lb_ctx_alloc_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* rss_cos_lb_ctx_id is 16 b */ + uint16_t rss_cos_lb_ctx_id; + + uint8_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + uint8_t unused_4; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_vnic_rss_cos_lb_ctx_free */ +/* Description: This function can be used to free COS/Load Balance context. */ +/* Input (24 bytes) */ + +struct hwrm_vnic_rss_cos_lb_ctx_free_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* rss_cos_lb_ctx_id is 16 b */ + uint16_t rss_cos_lb_ctx_id; + + uint16_t unused_0[3]; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_vnic_rss_cos_lb_ctx_free_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* Output (32 bytes) */ +struct hwrm_queue_qportcfg_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + /* The maximum number of queues that can be configured. */ + uint8_t max_configurable_queues; + + /* The maximum number of lossless queues that can be configured. */ + uint8_t max_configurable_lossless_queues; + + /* + * 0 - Not allowed. Non-zero - Allowed. If this value is non-zero, then + * the HWRM shall allow the host SW driver to configure queues using + * hwrm_queue_cfg. + */ + uint8_t queue_cfg_allowed; + + /* + * 0 - Not allowed. Non-zero - Allowed If this value is non-zero, then + * the HWRM shall allow the host SW driver to configure queue buffers + * using hwrm_queue_buffers_cfg. + */ + uint8_t queue_buffers_cfg_allowed; + + /* + * 0 - Not allowed. Non-zero - Allowed If this value is non-zero, then + * the HWRM shall allow the host SW driver to configure PFC using + * hwrm_queue_pfcenable_cfg. + */ + uint8_t queue_pfcenable_cfg_allowed; + + /* + * 0 - Not allowed. Non-zero - Allowed If this value is non-zero, then + * the HWRM shall allow the host SW driver to configure Priority to CoS + * mapping using hwrm_queue_pri2cos_cfg. + */ + uint8_t queue_pri2cos_cfg_allowed; + + /* + * 0 - Not allowed. Non-zero - Allowed If this value is non-zero, then + * the HWRM shall allow the host SW driver to configure CoS Bandwidth + * configuration using hwrm_queue_cos2bw_cfg. + */ + uint8_t queue_cos2bw_cfg_allowed; + + /* ID of CoS Queue 0. FF - Invalid id */ + uint8_t queue_id0; + + /* This value is applicable to CoS queues only. */ + /* Lossy (best-effort) */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSY \ + (UINT32_C(0x0) << 0) + /* Lossless */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSLESS \ + (UINT32_C(0x1) << 0) + /* + * Set to 0xFF... (All Fs) if there is no service profile + * specified + */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_UNKNOWN \ + (UINT32_C(0xff) << 0) + uint8_t queue_id0_service_profile; + + /* ID of CoS Queue 1. FF - Invalid id */ + uint8_t queue_id1; + /* This value is applicable to CoS queues only. */ + /* Lossy (best-effort) */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSY \ + (UINT32_C(0x0) << 0) + /* Lossless */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSLESS \ + (UINT32_C(0x1) << 0) + /* + * Set to 0xFF... (All Fs) if there is no service profile + * specified + */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_UNKNOWN \ + (UINT32_C(0xff) << 0) + uint8_t queue_id1_service_profile; + + /* ID of CoS Queue 2. FF - Invalid id */ + uint8_t queue_id2; + /* This value is applicable to CoS queues only. */ + /* Lossy (best-effort) */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSY \ + (UINT32_C(0x0) << 0) + /* Lossless */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSLESS \ + (UINT32_C(0x1) << 0) + /* + * Set to 0xFF... (All Fs) if there is no service profile + * specified + */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_UNKNOWN \ + (UINT32_C(0xff) << 0) + uint8_t queue_id2_service_profile; + + /* ID of CoS Queue 3. FF - Invalid id */ + uint8_t queue_id3; + + /* This value is applicable to CoS queues only. */ + /* Lossy (best-effort) */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSY \ + (UINT32_C(0x0) << 0) + /* Lossless */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS \ + (UINT32_C(0x1) << 0) + /* + * Set to 0xFF... (All Fs) if there is no service profile + * specified + */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN \ + (UINT32_C(0xff) << 0) + uint8_t queue_id3_service_profile; + + /* ID of CoS Queue 4. FF - Invalid id */ + uint8_t queue_id4; + /* This value is applicable to CoS queues only. */ + /* Lossy (best-effort) */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY \ + (UINT32_C(0x0) << 0) + /* Lossless */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS \ + (UINT32_C(0x1) << 0) + /* + * Set to 0xFF... (All Fs) if there is no service profile + * specified + */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN \ + (UINT32_C(0xff) << 0) + uint8_t queue_id4_service_profile; + + /* ID of CoS Queue 5. FF - Invalid id */ + uint8_t queue_id5; + + /* This value is applicable to CoS queues only. */ + /* Lossy (best-effort) */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY \ + (UINT32_C(0x0) << 0) + /* Lossless */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS \ + (UINT32_C(0x1) << 0) + /* + * Set to 0xFF... (All Fs) if there is no service profile + * specified + */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN \ + (UINT32_C(0xff) << 0) + uint8_t queue_id5_service_profile; + + /* ID of CoS Queue 6. FF - Invalid id */ + uint8_t queue_id6_service_profile; + /* This value is applicable to CoS queues only. */ + /* Lossy (best-effort) */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY \ + (UINT32_C(0x0) << 0) + /* Lossless */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS \ + (UINT32_C(0x1) << 0) + /* + * Set to 0xFF... (All Fs) if there is no service profile + * specified + */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN \ + (UINT32_C(0xff) << 0) + uint8_t queue_id6; + + /* ID of CoS Queue 7. FF - Invalid id */ + uint8_t queue_id7; + + /* This value is applicable to CoS queues only. */ + /* Lossy (best-effort) */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY \ + (UINT32_C(0x0) << 0) + /* Lossless */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS \ + (UINT32_C(0x1) << 0) + /* + * Set to 0xFF... (All Fs) if there is no service profile + * specified + */ + #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN \ + (UINT32_C(0xff) << 0) + uint8_t queue_id7_service_profile; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_func_drv_rgtr */ +/* + * Description: This command is used by the function driver to register its + * information with the HWRM. A function driver shall implement this command. A + * function driver shall use this command during the driver initialization right + * after the HWRM version discovery and default ring resources allocation. + */ + +/* Input (80 bytes) */ +struct hwrm_func_drv_rgtr_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * When this bit is '1', the function driver is requesting all requests + * from its children VF drivers to be forwarded to itself. This flag can + * only be set by the PF driver. If a VF driver sets this flag, it + * should be ignored by the HWRM. + */ + #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_ALL_MODE UINT32_C(0x1) + /* + * When this bit is '1', the function is requesting none of the requests + * from its children VF drivers to be forwarded to itself. This flag can + * only be set by the PF driver. If a VF driver sets this flag, it + * should be ignored by the HWRM. + */ + #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_NONE_MODE UINT32_C(0x2) + uint32_t flags; + + /* This bit must be '1' for the os_type field to be configured. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_OS_TYPE UINT32_C(0x1) + /* This bit must be '1' for the ver field to be configured. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VER UINT32_C(0x2) + /* This bit must be '1' for the timestamp field to be configured. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_TIMESTAMP UINT32_C(0x4) + /* This bit must be '1' for the vf_req_fwd field to be configured. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VF_REQ_FWD UINT32_C(0x8) + /* + * This bit must be '1' for the async_event_fwd field to be configured. + */ + #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_ASYNC_EVENT_FWD \ + UINT32_C(0x10) + uint32_t enables; + + /* This value indicates the type of OS. */ + /* Unknown */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_UNKNOWN \ + (UINT32_C(0x0) << 0) + /* Other OS not listed below. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_OTHER \ + (UINT32_C(0x1) << 0) + /* MSDOS OS. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_MSDOS \ + (UINT32_C(0xe) << 0) + /* Windows OS. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WINDOWS \ + (UINT32_C(0x12) << 0) + /* Solaris OS. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_SOLARIS \ + (UINT32_C(0x1d) << 0) + /* Linux OS. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_LINUX \ + (UINT32_C(0x24) << 0) + /* FreeBSD OS. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_FREEBSD \ + (UINT32_C(0x2a) << 0) + /* VMware ESXi OS. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_ESXI \ + (UINT32_C(0x68) << 0) + /* Microsoft Windows 8 64-bit OS. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN864 \ + (UINT32_C(0x73) << 0) + /* Microsoft Windows Server 2012 R2 OS. */ + #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN2012R2 \ + (UINT32_C(0x74) << 0) + uint16_t os_type; + + /* This is the major version of the driver. */ + uint8_t ver_maj; + + /* This is the minor version of the driver. */ + uint8_t ver_min; + + /* This is the update version of the driver. */ + uint8_t ver_upd; + + uint8_t unused_0; + uint16_t unused_1; + + /* + * This is a 32-bit timestamp provided by the driver for keep alive. The + * timestamp is in multiples of 1ms. + */ + uint32_t timestamp; + + uint32_t unused_2; + + /* + * This is a 256-bit bit mask provided by the PF driver for letting the + * HWRM know what commands issued by the VF driver to the HWRM should be + * forwarded to the PF driver. Nth bit refers to the Nth req_type. + * Setting Nth bit to 1 indicates that requests from the VF driver with + * req_type equal to N shall be forwarded to the parent PF driver. This + * field is not valid for the VF driver. + */ + uint32_t vf_req_fwd[8]; + + /* + * This is a 256-bit bit mask provided by the function driver (PF or VF + * driver) to indicate the list of asynchronous event completions to be + * forwarded. Nth bit refers to the Nth event_id. Setting Nth bit to 1 + * by the function driver shall result in the HWRM forwarding + * asynchronous event completion with event_id equal to N. If all bits + * are set to 0 (value of 0), then the HWRM shall not forward any + * asynchronous event completion to this function driver. + */ + uint32_t async_event_fwd[8]; +} __attribute__((packed)); + +/* Output (16 bytes) */ + +struct hwrm_func_drv_rgtr_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +/* hwrm_func_drv_unrgtr */ +/* + * Description: This command is used by the function driver to un register with + * the HWRM. A function driver shall implement this command. A function driver + * shall use this command during the driver unloading. + */ +/* Input (24 bytes) */ + +struct hwrm_func_drv_unrgtr_input { + /* + * This value indicates what type of request this is. The format for the + * rest of the command is determined by this field. + */ + uint16_t req_type; + + /* + * This value indicates the what completion ring the request will be + * optionally completed on. If the value is -1, then no CR completion + * will be generated. Any other value must be a valid CR ring_id value + * for this function. + */ + uint16_t cmpl_ring; + + /* This value indicates the command sequence number. */ + uint16_t seq_id; + + /* + * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids + * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM + */ + uint16_t target_id; + + /* + * This is the host address where the response will be written when the + * request is complete. This area must be 16B aligned and must be + * cleared to zero before the request is made. + */ + uint64_t resp_addr; + + /* + * When this bit is '1', the function driver is notifying the HWRM to + * prepare for the shutdown. + */ + #define HWRM_FUNC_DRV_UNRGTR_INPUT_FLAGS_PREPARE_FOR_SHUTDOWN \ + UINT32_C(0x1) + uint32_t flags; + + uint32_t unused_0; +} __attribute__((packed)); + +/* Output (16 bytes) */ +struct hwrm_func_drv_unrgtr_output { + /* + * Pass/Fail or error type Note: receiver to verify the in parameters, + * and fail the call with an error when appropriate + */ + uint16_t error_code; + + /* This field returns the type of original request. */ + uint16_t req_type; + + /* This field provides original sequence number of the command. */ + uint16_t seq_id; + + /* + * This field is the length of the response in bytes. The last byte of + * the response is a valid flag that will read as '1' when the command + * has been completely written to memory. + */ + uint16_t resp_len; + + uint32_t unused_0; + uint8_t unused_1; + uint8_t unused_2; + uint8_t unused_3; + + /* + * This field is used in Output records to indicate that the output is + * completely written to RAM. This field should be read as '1' to + * indicate that the output has been completely written. When writing a + * command completion or response to an internal processor, the order of + * writes has to be such that this field is written last. + */ + uint8_t valid; +} __attribute__((packed)); + +#endif |