summaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000/base/e1000_82542.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000/base/e1000_82542.c')
-rw-r--r--drivers/net/e1000/base/e1000_82542.c590
1 files changed, 590 insertions, 0 deletions
diff --git a/drivers/net/e1000/base/e1000_82542.c b/drivers/net/e1000/base/e1000_82542.c
new file mode 100644
index 00000000..4f1183af
--- /dev/null
+++ b/drivers/net/e1000/base/e1000_82542.c
@@ -0,0 +1,590 @@
+/*******************************************************************************
+
+Copyright (c) 2001-2015, Intel Corporation
+All rights reserved.
+
+Redistribution and use in source and binary forms, with or without
+modification, are permitted provided that the following conditions are met:
+
+ 1. Redistributions of source code must retain the above copyright notice,
+ this list of conditions and the following disclaimer.
+
+ 2. Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in the
+ documentation and/or other materials provided with the distribution.
+
+ 3. Neither the name of the Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived from
+ this software without specific prior written permission.
+
+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGE.
+
+***************************************************************************/
+
+/*
+ * 82542 Gigabit Ethernet Controller
+ */
+
+#include "e1000_api.h"
+
+STATIC s32 e1000_init_phy_params_82542(struct e1000_hw *hw);
+STATIC s32 e1000_init_nvm_params_82542(struct e1000_hw *hw);
+STATIC s32 e1000_init_mac_params_82542(struct e1000_hw *hw);
+STATIC s32 e1000_get_bus_info_82542(struct e1000_hw *hw);
+STATIC s32 e1000_reset_hw_82542(struct e1000_hw *hw);
+STATIC s32 e1000_init_hw_82542(struct e1000_hw *hw);
+STATIC s32 e1000_setup_link_82542(struct e1000_hw *hw);
+STATIC s32 e1000_led_on_82542(struct e1000_hw *hw);
+STATIC s32 e1000_led_off_82542(struct e1000_hw *hw);
+STATIC int e1000_rar_set_82542(struct e1000_hw *hw, u8 *addr, u32 index);
+STATIC void e1000_clear_hw_cntrs_82542(struct e1000_hw *hw);
+STATIC s32 e1000_read_mac_addr_82542(struct e1000_hw *hw);
+
+/**
+ * e1000_init_phy_params_82542 - Init PHY func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+STATIC s32 e1000_init_phy_params_82542(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_init_phy_params_82542");
+
+ phy->type = e1000_phy_none;
+
+ return ret_val;
+}
+
+/**
+ * e1000_init_nvm_params_82542 - Init NVM func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+STATIC s32 e1000_init_nvm_params_82542(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+
+ DEBUGFUNC("e1000_init_nvm_params_82542");
+
+ nvm->address_bits = 6;
+ nvm->delay_usec = 50;
+ nvm->opcode_bits = 3;
+ nvm->type = e1000_nvm_eeprom_microwire;
+ nvm->word_size = 64;
+
+ /* Function Pointers */
+ nvm->ops.read = e1000_read_nvm_microwire;
+ nvm->ops.release = e1000_stop_nvm;
+ nvm->ops.write = e1000_write_nvm_microwire;
+ nvm->ops.update = e1000_update_nvm_checksum_generic;
+ nvm->ops.validate = e1000_validate_nvm_checksum_generic;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_init_mac_params_82542 - Init MAC func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+STATIC s32 e1000_init_mac_params_82542(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+
+ DEBUGFUNC("e1000_init_mac_params_82542");
+
+ /* Set media type */
+ hw->phy.media_type = e1000_media_type_fiber;
+
+ /* Set mta register count */
+ mac->mta_reg_count = 128;
+ /* Set rar entry count */
+ mac->rar_entry_count = E1000_RAR_ENTRIES;
+
+ /* Function pointers */
+
+ /* bus type/speed/width */
+ mac->ops.get_bus_info = e1000_get_bus_info_82542;
+ /* function id */
+ mac->ops.set_lan_id = e1000_set_lan_id_multi_port_pci;
+ /* reset */
+ mac->ops.reset_hw = e1000_reset_hw_82542;
+ /* hw initialization */
+ mac->ops.init_hw = e1000_init_hw_82542;
+ /* link setup */
+ mac->ops.setup_link = e1000_setup_link_82542;
+ /* phy/fiber/serdes setup */
+ mac->ops.setup_physical_interface =
+ e1000_setup_fiber_serdes_link_generic;
+ /* check for link */
+ mac->ops.check_for_link = e1000_check_for_fiber_link_generic;
+ /* multicast address update */
+ mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic;
+ /* writing VFTA */
+ mac->ops.write_vfta = e1000_write_vfta_generic;
+ /* clearing VFTA */
+ mac->ops.clear_vfta = e1000_clear_vfta_generic;
+ /* read mac address */
+ mac->ops.read_mac_addr = e1000_read_mac_addr_82542;
+ /* set RAR */
+ mac->ops.rar_set = e1000_rar_set_82542;
+ /* turn on/off LED */
+ mac->ops.led_on = e1000_led_on_82542;
+ mac->ops.led_off = e1000_led_off_82542;
+ /* clear hardware counters */
+ mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82542;
+ /* link info */
+ mac->ops.get_link_up_info =
+ e1000_get_speed_and_duplex_fiber_serdes_generic;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_init_function_pointers_82542 - Init func ptrs.
+ * @hw: pointer to the HW structure
+ *
+ * Called to initialize all function pointers and parameters.
+ **/
+void e1000_init_function_pointers_82542(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_init_function_pointers_82542");
+
+ hw->mac.ops.init_params = e1000_init_mac_params_82542;
+ hw->nvm.ops.init_params = e1000_init_nvm_params_82542;
+ hw->phy.ops.init_params = e1000_init_phy_params_82542;
+}
+
+/**
+ * e1000_get_bus_info_82542 - Obtain bus information for adapter
+ * @hw: pointer to the HW structure
+ *
+ * This will obtain information about the HW bus for which the
+ * adapter is attached and stores it in the hw structure.
+ **/
+STATIC s32 e1000_get_bus_info_82542(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_get_bus_info_82542");
+
+ hw->bus.type = e1000_bus_type_pci;
+ hw->bus.speed = e1000_bus_speed_unknown;
+ hw->bus.width = e1000_bus_width_unknown;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_reset_hw_82542 - Reset hardware
+ * @hw: pointer to the HW structure
+ *
+ * This resets the hardware into a known state.
+ **/
+STATIC s32 e1000_reset_hw_82542(struct e1000_hw *hw)
+{
+ struct e1000_bus_info *bus = &hw->bus;
+ s32 ret_val = E1000_SUCCESS;
+ u32 ctrl;
+
+ DEBUGFUNC("e1000_reset_hw_82542");
+
+ if (hw->revision_id == E1000_REVISION_2) {
+ DEBUGOUT("Disabling MWI on 82542 rev 2\n");
+ e1000_pci_clear_mwi(hw);
+ }
+
+ DEBUGOUT("Masking off all interrupts\n");
+ E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff);
+
+ E1000_WRITE_REG(hw, E1000_RCTL, 0);
+ E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP);
+ E1000_WRITE_FLUSH(hw);
+
+ /*
+ * Delay to allow any outstanding PCI transactions to complete before
+ * resetting the device
+ */
+ msec_delay(10);
+
+ ctrl = E1000_READ_REG(hw, E1000_CTRL);
+
+ DEBUGOUT("Issuing a global reset to 82542/82543 MAC\n");
+ E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST);
+
+ hw->nvm.ops.reload(hw);
+ msec_delay(2);
+
+ E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff);
+ E1000_READ_REG(hw, E1000_ICR);
+
+ if (hw->revision_id == E1000_REVISION_2) {
+ if (bus->pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_init_hw_82542 - Initialize hardware
+ * @hw: pointer to the HW structure
+ *
+ * This inits the hardware readying it for operation.
+ **/
+STATIC s32 e1000_init_hw_82542(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ struct e1000_dev_spec_82542 *dev_spec = &hw->dev_spec._82542;
+ s32 ret_val = E1000_SUCCESS;
+ u32 ctrl;
+ u16 i;
+
+ DEBUGFUNC("e1000_init_hw_82542");
+
+ /* Disabling VLAN filtering */
+ E1000_WRITE_REG(hw, E1000_VET, 0);
+ mac->ops.clear_vfta(hw);
+
+ /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
+ if (hw->revision_id == E1000_REVISION_2) {
+ DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+ e1000_pci_clear_mwi(hw);
+ E1000_WRITE_REG(hw, E1000_RCTL, E1000_RCTL_RST);
+ E1000_WRITE_FLUSH(hw);
+ msec_delay(5);
+ }
+
+ /* Setup the receive address. */
+ e1000_init_rx_addrs_generic(hw, mac->rar_entry_count);
+
+ /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
+ if (hw->revision_id == E1000_REVISION_2) {
+ E1000_WRITE_REG(hw, E1000_RCTL, 0);
+ E1000_WRITE_FLUSH(hw);
+ msec_delay(1);
+ if (hw->bus.pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+ }
+
+ /* Zero out the Multicast HASH table */
+ DEBUGOUT("Zeroing the MTA\n");
+ for (i = 0; i < mac->mta_reg_count; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+ /*
+ * Set the PCI priority bit correctly in the CTRL register. This
+ * determines if the adapter gives priority to receives, or if it
+ * gives equal priority to transmits and receives.
+ */
+ if (dev_spec->dma_fairness) {
+ ctrl = E1000_READ_REG(hw, E1000_CTRL);
+ E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_PRIOR);
+ }
+
+ /* Setup link and flow control */
+ ret_val = e1000_setup_link_82542(hw);
+
+ /*
+ * Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000_clear_hw_cntrs_82542(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_setup_link_82542 - Setup flow control and link settings
+ * @hw: pointer to the HW structure
+ *
+ * Determines which flow control settings to use, then configures flow
+ * control. Calls the appropriate media-specific link configuration
+ * function. Assuming the adapter has a valid link partner, a valid link
+ * should be established. Assumes the hardware has previously been reset
+ * and the transmitter and receiver are not enabled.
+ **/
+STATIC s32 e1000_setup_link_82542(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_setup_link_82542");
+
+ ret_val = e1000_set_default_fc_generic(hw);
+ if (ret_val)
+ goto out;
+
+ hw->fc.requested_mode &= ~e1000_fc_tx_pause;
+
+ if (mac->report_tx_early)
+ hw->fc.requested_mode &= ~e1000_fc_rx_pause;
+
+ /*
+ * Save off the requested flow control mode for use later. Depending
+ * on the link partner's capabilities, we may or may not use this mode.
+ */
+ hw->fc.current_mode = hw->fc.requested_mode;
+
+ DEBUGOUT1("After fix-ups FlowControl is now = %x\n",
+ hw->fc.current_mode);
+
+ /* Call the necessary subroutine to configure the link. */
+ ret_val = mac->ops.setup_physical_interface(hw);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Initialize the flow control address, type, and PAUSE timer
+ * registers to their default values. This is done even if flow
+ * control is disabled, because it does not hurt anything to
+ * initialize these registers.
+ */
+ DEBUGOUT("Initializing Flow Control address, type and timer regs\n");
+
+ E1000_WRITE_REG(hw, E1000_FCAL, FLOW_CONTROL_ADDRESS_LOW);
+ E1000_WRITE_REG(hw, E1000_FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ E1000_WRITE_REG(hw, E1000_FCT, FLOW_CONTROL_TYPE);
+
+ E1000_WRITE_REG(hw, E1000_FCTTV, hw->fc.pause_time);
+
+ ret_val = e1000_set_fc_watermarks_generic(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_led_on_82542 - Turn on SW controllable LED
+ * @hw: pointer to the HW structure
+ *
+ * Turns the SW defined LED on.
+ **/
+STATIC s32 e1000_led_on_82542(struct e1000_hw *hw)
+{
+ u32 ctrl = E1000_READ_REG(hw, E1000_CTRL);
+
+ DEBUGFUNC("e1000_led_on_82542");
+
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ E1000_WRITE_REG(hw, E1000_CTRL, ctrl);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_led_off_82542 - Turn off SW controllable LED
+ * @hw: pointer to the HW structure
+ *
+ * Turns the SW defined LED off.
+ **/
+STATIC s32 e1000_led_off_82542(struct e1000_hw *hw)
+{
+ u32 ctrl = E1000_READ_REG(hw, E1000_CTRL);
+
+ DEBUGFUNC("e1000_led_off_82542");
+
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ E1000_WRITE_REG(hw, E1000_CTRL, ctrl);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_rar_set_82542 - Set receive address register
+ * @hw: pointer to the HW structure
+ * @addr: pointer to the receive address
+ * @index: receive address array register
+ *
+ * Sets the receive address array register at index to the address passed
+ * in by addr.
+ **/
+STATIC int e1000_rar_set_82542(struct e1000_hw *hw, u8 *addr, u32 index)
+{
+ u32 rar_low, rar_high;
+
+ DEBUGFUNC("e1000_rar_set_82542");
+
+ /*
+ * HW expects these in little endian so we reverse the byte order
+ * from network order (big endian) to little endian
+ */
+ rar_low = ((u32) addr[0] | ((u32) addr[1] << 8) |
+ ((u32) addr[2] << 16) | ((u32) addr[3] << 24));
+
+ rar_high = ((u32) addr[4] | ((u32) addr[5] << 8));
+
+ /* If MAC address zero, no need to set the AV bit */
+ if (rar_low || rar_high)
+ rar_high |= E1000_RAH_AV;
+
+ E1000_WRITE_REG_ARRAY(hw, E1000_RA, (index << 1), rar_low);
+ E1000_WRITE_REG_ARRAY(hw, E1000_RA, ((index << 1) + 1), rar_high);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_translate_register_82542 - Translate the proper register offset
+ * @reg: e1000 register to be read
+ *
+ * Registers in 82542 are located in different offsets than other adapters
+ * even though they function in the same manner. This function takes in
+ * the name of the register to read and returns the correct offset for
+ * 82542 silicon.
+ **/
+u32 e1000_translate_register_82542(u32 reg)
+{
+ /*
+ * Some of the 82542 registers are located at different
+ * offsets than they are in newer adapters.
+ * Despite the difference in location, the registers
+ * function in the same manner.
+ */
+ switch (reg) {
+ case E1000_RA:
+ reg = 0x00040;
+ break;
+ case E1000_RDTR:
+ reg = 0x00108;
+ break;
+ case E1000_RDBAL(0):
+ reg = 0x00110;
+ break;
+ case E1000_RDBAH(0):
+ reg = 0x00114;
+ break;
+ case E1000_RDLEN(0):
+ reg = 0x00118;
+ break;
+ case E1000_RDH(0):
+ reg = 0x00120;
+ break;
+ case E1000_RDT(0):
+ reg = 0x00128;
+ break;
+ case E1000_RDBAL(1):
+ reg = 0x00138;
+ break;
+ case E1000_RDBAH(1):
+ reg = 0x0013C;
+ break;
+ case E1000_RDLEN(1):
+ reg = 0x00140;
+ break;
+ case E1000_RDH(1):
+ reg = 0x00148;
+ break;
+ case E1000_RDT(1):
+ reg = 0x00150;
+ break;
+ case E1000_FCRTH:
+ reg = 0x00160;
+ break;
+ case E1000_FCRTL:
+ reg = 0x00168;
+ break;
+ case E1000_MTA:
+ reg = 0x00200;
+ break;
+ case E1000_TDBAL(0):
+ reg = 0x00420;
+ break;
+ case E1000_TDBAH(0):
+ reg = 0x00424;
+ break;
+ case E1000_TDLEN(0):
+ reg = 0x00428;
+ break;
+ case E1000_TDH(0):
+ reg = 0x00430;
+ break;
+ case E1000_TDT(0):
+ reg = 0x00438;
+ break;
+ case E1000_TIDV:
+ reg = 0x00440;
+ break;
+ case E1000_VFTA:
+ reg = 0x00600;
+ break;
+ case E1000_TDFH:
+ reg = 0x08010;
+ break;
+ case E1000_TDFT:
+ reg = 0x08018;
+ break;
+ default:
+ break;
+ }
+
+ return reg;
+}
+
+/**
+ * e1000_clear_hw_cntrs_82542 - Clear device specific hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the hardware counters by reading the counter registers.
+ **/
+STATIC void e1000_clear_hw_cntrs_82542(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_clear_hw_cntrs_82542");
+
+ e1000_clear_hw_cntrs_base_generic(hw);
+
+ E1000_READ_REG(hw, E1000_PRC64);
+ E1000_READ_REG(hw, E1000_PRC127);
+ E1000_READ_REG(hw, E1000_PRC255);
+ E1000_READ_REG(hw, E1000_PRC511);
+ E1000_READ_REG(hw, E1000_PRC1023);
+ E1000_READ_REG(hw, E1000_PRC1522);
+ E1000_READ_REG(hw, E1000_PTC64);
+ E1000_READ_REG(hw, E1000_PTC127);
+ E1000_READ_REG(hw, E1000_PTC255);
+ E1000_READ_REG(hw, E1000_PTC511);
+ E1000_READ_REG(hw, E1000_PTC1023);
+ E1000_READ_REG(hw, E1000_PTC1522);
+}
+
+/**
+ * e1000_read_mac_addr_82542 - Read device MAC address
+ * @hw: pointer to the HW structure
+ *
+ * Reads the device MAC address from the EEPROM and stores the value.
+ **/
+s32 e1000_read_mac_addr_82542(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 offset, nvm_data, i;
+
+ DEBUGFUNC("e1000_read_mac_addr");
+
+ for (i = 0; i < ETH_ADDR_LEN; i += 2) {
+ offset = i >> 1;
+ ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data);
+ if (ret_val) {
+ DEBUGOUT("NVM Read Error\n");
+ goto out;
+ }
+ hw->mac.perm_addr[i] = (u8)(nvm_data & 0xFF);
+ hw->mac.perm_addr[i+1] = (u8)(nvm_data >> 8);
+ }
+
+ for (i = 0; i < ETH_ADDR_LEN; i++)
+ hw->mac.addr[i] = hw->mac.perm_addr[i];
+
+out:
+ return ret_val;
+}