diff options
Diffstat (limited to 'drivers/net/e1000/base/e1000_ich8lan.c')
| -rw-r--r-- | drivers/net/e1000/base/e1000_ich8lan.c | 5366 |
1 files changed, 5366 insertions, 0 deletions
diff --git a/drivers/net/e1000/base/e1000_ich8lan.c b/drivers/net/e1000/base/e1000_ich8lan.c new file mode 100644 index 00000000..89d07e90 --- /dev/null +++ b/drivers/net/e1000/base/e1000_ich8lan.c @@ -0,0 +1,5366 @@ +/******************************************************************************* + +Copyright (c) 2001-2015, Intel Corporation +All rights reserved. + +Redistribution and use in source and binary forms, with or without +modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + +THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE +ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE +LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR +CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF +SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS +INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN +CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +POSSIBILITY OF SUCH DAMAGE. + +***************************************************************************/ + +/* 82562G 10/100 Network Connection + * 82562G-2 10/100 Network Connection + * 82562GT 10/100 Network Connection + * 82562GT-2 10/100 Network Connection + * 82562V 10/100 Network Connection + * 82562V-2 10/100 Network Connection + * 82566DC-2 Gigabit Network Connection + * 82566DC Gigabit Network Connection + * 82566DM-2 Gigabit Network Connection + * 82566DM Gigabit Network Connection + * 82566MC Gigabit Network Connection + * 82566MM Gigabit Network Connection + * 82567LM Gigabit Network Connection + * 82567LF Gigabit Network Connection + * 82567V Gigabit Network Connection + * 82567LM-2 Gigabit Network Connection + * 82567LF-2 Gigabit Network Connection + * 82567V-2 Gigabit Network Connection + * 82567LF-3 Gigabit Network Connection + * 82567LM-3 Gigabit Network Connection + * 82567LM-4 Gigabit Network Connection + * 82577LM Gigabit Network Connection + * 82577LC Gigabit Network Connection + * 82578DM Gigabit Network Connection + * 82578DC Gigabit Network Connection + * 82579LM Gigabit Network Connection + * 82579V Gigabit Network Connection + * Ethernet Connection I217-LM + * Ethernet Connection I217-V + * Ethernet Connection I218-V + * Ethernet Connection I218-LM + * Ethernet Connection (2) I218-LM + * Ethernet Connection (2) I218-V + * Ethernet Connection (3) I218-LM + * Ethernet Connection (3) I218-V + */ + +#include "e1000_api.h" + +STATIC s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state); +STATIC s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw); +STATIC void e1000_release_swflag_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_acquire_nvm_ich8lan(struct e1000_hw *hw); +STATIC void e1000_release_nvm_ich8lan(struct e1000_hw *hw); +STATIC bool e1000_check_mng_mode_ich8lan(struct e1000_hw *hw); +STATIC bool e1000_check_mng_mode_pchlan(struct e1000_hw *hw); +STATIC int e1000_rar_set_pch2lan(struct e1000_hw *hw, u8 *addr, u32 index); +STATIC int e1000_rar_set_pch_lpt(struct e1000_hw *hw, u8 *addr, u32 index); +STATIC s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw); +#ifndef NO_NON_BLOCKING_PHY_MTA_UPDATE_SUPPORT +STATIC void e1000_update_mc_addr_list_pch2lan(struct e1000_hw *hw, + u8 *mc_addr_list, + u32 mc_addr_count); +#endif /* NO_NON_BLOCKING_PHY_MTA_UPDATE_SUPPORT */ +STATIC s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active); +STATIC s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, + bool active); +STATIC s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, + bool active); +STATIC s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +STATIC s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +STATIC s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, + u16 *data); +STATIC s32 e1000_id_led_init_pchlan(struct e1000_hw *hw); +STATIC s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_init_hw_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_setup_link_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_setup_copper_link_pch_lpt(struct e1000_hw *hw); +STATIC s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, + u16 *speed, u16 *duplex); +STATIC s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_led_on_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_led_off_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link); +STATIC s32 e1000_setup_led_pchlan(struct e1000_hw *hw); +STATIC s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw); +STATIC s32 e1000_led_on_pchlan(struct e1000_hw *hw); +STATIC s32 e1000_led_off_pchlan(struct e1000_hw *hw); +STATIC void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank); +STATIC void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, + u32 offset, u8 *data); +STATIC s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 *data); +STATIC s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, + u32 offset, u16 *data); +STATIC s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, + u32 offset, u8 byte); +STATIC s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw); +STATIC void e1000_power_down_phy_copper_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw); +STATIC s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw); +STATIC s32 e1000_k1_workaround_lv(struct e1000_hw *hw); +STATIC void e1000_gate_hw_phy_config_ich8lan(struct e1000_hw *hw, bool gate); + +/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ +/* Offset 04h HSFSTS */ +union ich8_hws_flash_status { + struct ich8_hsfsts { + u16 flcdone:1; /* bit 0 Flash Cycle Done */ + u16 flcerr:1; /* bit 1 Flash Cycle Error */ + u16 dael:1; /* bit 2 Direct Access error Log */ + u16 berasesz:2; /* bit 4:3 Sector Erase Size */ + u16 flcinprog:1; /* bit 5 flash cycle in Progress */ + u16 reserved1:2; /* bit 13:6 Reserved */ + u16 reserved2:6; /* bit 13:6 Reserved */ + u16 fldesvalid:1; /* bit 14 Flash Descriptor Valid */ + u16 flockdn:1; /* bit 15 Flash Config Lock-Down */ + } hsf_status; + u16 regval; +}; + +/* ICH GbE Flash Hardware Sequencing Flash control Register bit breakdown */ +/* Offset 06h FLCTL */ +union ich8_hws_flash_ctrl { + struct ich8_hsflctl { + u16 flcgo:1; /* 0 Flash Cycle Go */ + u16 flcycle:2; /* 2:1 Flash Cycle */ + u16 reserved:5; /* 7:3 Reserved */ + u16 fldbcount:2; /* 9:8 Flash Data Byte Count */ + u16 flockdn:6; /* 15:10 Reserved */ + } hsf_ctrl; + u16 regval; +}; + +/* ICH Flash Region Access Permissions */ +union ich8_hws_flash_regacc { + struct ich8_flracc { + u32 grra:8; /* 0:7 GbE region Read Access */ + u32 grwa:8; /* 8:15 GbE region Write Access */ + u32 gmrag:8; /* 23:16 GbE Master Read Access Grant */ + u32 gmwag:8; /* 31:24 GbE Master Write Access Grant */ + } hsf_flregacc; + u16 regval; +}; + +/** + * e1000_phy_is_accessible_pchlan - Check if able to access PHY registers + * @hw: pointer to the HW structure + * + * Test access to the PHY registers by reading the PHY ID registers. If + * the PHY ID is already known (e.g. resume path) compare it with known ID, + * otherwise assume the read PHY ID is correct if it is valid. + * + * Assumes the sw/fw/hw semaphore is already acquired. + **/ +STATIC bool e1000_phy_is_accessible_pchlan(struct e1000_hw *hw) +{ + u16 phy_reg = 0; + u32 phy_id = 0; + s32 ret_val = 0; + u16 retry_count; + u32 mac_reg = 0; + + for (retry_count = 0; retry_count < 2; retry_count++) { + ret_val = hw->phy.ops.read_reg_locked(hw, PHY_ID1, &phy_reg); + if (ret_val || (phy_reg == 0xFFFF)) + continue; + phy_id = (u32)(phy_reg << 16); + + ret_val = hw->phy.ops.read_reg_locked(hw, PHY_ID2, &phy_reg); + if (ret_val || (phy_reg == 0xFFFF)) { + phy_id = 0; + continue; + } + phy_id |= (u32)(phy_reg & PHY_REVISION_MASK); + break; + } + + if (hw->phy.id) { + if (hw->phy.id == phy_id) + goto out; + } else if (phy_id) { + hw->phy.id = phy_id; + hw->phy.revision = (u32)(phy_reg & ~PHY_REVISION_MASK); + goto out; + } + + /* In case the PHY needs to be in mdio slow mode, + * set slow mode and try to get the PHY id again. + */ + if (hw->mac.type < e1000_pch_lpt) { + hw->phy.ops.release(hw); + ret_val = e1000_set_mdio_slow_mode_hv(hw); + if (!ret_val) + ret_val = e1000_get_phy_id(hw); + hw->phy.ops.acquire(hw); + } + + if (ret_val) + return false; +out: + if (hw->mac.type == e1000_pch_lpt) { + /* Only unforce SMBus if ME is not active */ + if (!(E1000_READ_REG(hw, E1000_FWSM) & + E1000_ICH_FWSM_FW_VALID)) { + /* Unforce SMBus mode in PHY */ + hw->phy.ops.read_reg_locked(hw, CV_SMB_CTRL, &phy_reg); + phy_reg &= ~CV_SMB_CTRL_FORCE_SMBUS; + hw->phy.ops.write_reg_locked(hw, CV_SMB_CTRL, phy_reg); + + /* Unforce SMBus mode in MAC */ + mac_reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, mac_reg); + } + } + + return true; +} + +/** + * e1000_toggle_lanphypc_pch_lpt - toggle the LANPHYPC pin value + * @hw: pointer to the HW structure + * + * Toggling the LANPHYPC pin value fully power-cycles the PHY and is + * used to reset the PHY to a quiescent state when necessary. + **/ +STATIC void e1000_toggle_lanphypc_pch_lpt(struct e1000_hw *hw) +{ + u32 mac_reg; + + DEBUGFUNC("e1000_toggle_lanphypc_pch_lpt"); + + /* Set Phy Config Counter to 50msec */ + mac_reg = E1000_READ_REG(hw, E1000_FEXTNVM3); + mac_reg &= ~E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK; + mac_reg |= E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC; + E1000_WRITE_REG(hw, E1000_FEXTNVM3, mac_reg); + + /* Toggle LANPHYPC Value bit */ + mac_reg = E1000_READ_REG(hw, E1000_CTRL); + mac_reg |= E1000_CTRL_LANPHYPC_OVERRIDE; + mac_reg &= ~E1000_CTRL_LANPHYPC_VALUE; + E1000_WRITE_REG(hw, E1000_CTRL, mac_reg); + E1000_WRITE_FLUSH(hw); + usec_delay(10); + mac_reg &= ~E1000_CTRL_LANPHYPC_OVERRIDE; + E1000_WRITE_REG(hw, E1000_CTRL, mac_reg); + E1000_WRITE_FLUSH(hw); + + if (hw->mac.type < e1000_pch_lpt) { + msec_delay(50); + } else { + u16 count = 20; + + do { + msec_delay(5); + } while (!(E1000_READ_REG(hw, E1000_CTRL_EXT) & + E1000_CTRL_EXT_LPCD) && count--); + + msec_delay(30); + } +} + +/** + * e1000_init_phy_workarounds_pchlan - PHY initialization workarounds + * @hw: pointer to the HW structure + * + * Workarounds/flow necessary for PHY initialization during driver load + * and resume paths. + **/ +STATIC s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw) +{ + u32 mac_reg, fwsm = E1000_READ_REG(hw, E1000_FWSM); + s32 ret_val; + + DEBUGFUNC("e1000_init_phy_workarounds_pchlan"); + + /* Gate automatic PHY configuration by hardware on managed and + * non-managed 82579 and newer adapters. + */ + e1000_gate_hw_phy_config_ich8lan(hw, true); + +#ifdef ULP_SUPPORT + /* It is not possible to be certain of the current state of ULP + * so forcibly disable it. + */ + hw->dev_spec.ich8lan.ulp_state = e1000_ulp_state_unknown; + +#endif /* ULP_SUPPORT */ + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) { + DEBUGOUT("Failed to initialize PHY flow\n"); + goto out; + } + + /* The MAC-PHY interconnect may be in SMBus mode. If the PHY is + * inaccessible and resetting the PHY is not blocked, toggle the + * LANPHYPC Value bit to force the interconnect to PCIe mode. + */ + switch (hw->mac.type) { + case e1000_pch_lpt: + if (e1000_phy_is_accessible_pchlan(hw)) + break; + + /* Before toggling LANPHYPC, see if PHY is accessible by + * forcing MAC to SMBus mode first. + */ + mac_reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + mac_reg |= E1000_CTRL_EXT_FORCE_SMBUS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, mac_reg); + + /* Wait 50 milliseconds for MAC to finish any retries + * that it might be trying to perform from previous + * attempts to acknowledge any phy read requests. + */ + msec_delay(50); + + /* fall-through */ + case e1000_pch2lan: + if (e1000_phy_is_accessible_pchlan(hw)) + break; + + /* fall-through */ + case e1000_pchlan: + if ((hw->mac.type == e1000_pchlan) && + (fwsm & E1000_ICH_FWSM_FW_VALID)) + break; + + if (hw->phy.ops.check_reset_block(hw)) { + DEBUGOUT("Required LANPHYPC toggle blocked by ME\n"); + ret_val = -E1000_ERR_PHY; + break; + } + + /* Toggle LANPHYPC Value bit */ + e1000_toggle_lanphypc_pch_lpt(hw); + if (hw->mac.type >= e1000_pch_lpt) { + if (e1000_phy_is_accessible_pchlan(hw)) + break; + + /* Toggling LANPHYPC brings the PHY out of SMBus mode + * so ensure that the MAC is also out of SMBus mode + */ + mac_reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, mac_reg); + + if (e1000_phy_is_accessible_pchlan(hw)) + break; + + ret_val = -E1000_ERR_PHY; + } + break; + default: + break; + } + + hw->phy.ops.release(hw); + if (!ret_val) { + + /* Check to see if able to reset PHY. Print error if not */ + if (hw->phy.ops.check_reset_block(hw)) { + ERROR_REPORT("Reset blocked by ME\n"); + goto out; + } + + /* Reset the PHY before any access to it. Doing so, ensures + * that the PHY is in a known good state before we read/write + * PHY registers. The generic reset is sufficient here, + * because we haven't determined the PHY type yet. + */ + ret_val = e1000_phy_hw_reset_generic(hw); + if (ret_val) + goto out; + + /* On a successful reset, possibly need to wait for the PHY + * to quiesce to an accessible state before returning control + * to the calling function. If the PHY does not quiesce, then + * return E1000E_BLK_PHY_RESET, as this is the condition that + * the PHY is in. + */ + ret_val = hw->phy.ops.check_reset_block(hw); + if (ret_val) + ERROR_REPORT("ME blocked access to PHY after reset\n"); + } + +out: + /* Ungate automatic PHY configuration on non-managed 82579 */ + if ((hw->mac.type == e1000_pch2lan) && + !(fwsm & E1000_ICH_FWSM_FW_VALID)) { + msec_delay(10); + e1000_gate_hw_phy_config_ich8lan(hw, false); + } + + return ret_val; +} + +/** + * e1000_init_phy_params_pchlan - Initialize PHY function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific PHY parameters and function pointers. + **/ +STATIC s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + + DEBUGFUNC("e1000_init_phy_params_pchlan"); + + phy->addr = 1; + phy->reset_delay_us = 100; + + phy->ops.acquire = e1000_acquire_swflag_ich8lan; + phy->ops.check_reset_block = e1000_check_reset_block_ich8lan; + phy->ops.get_cfg_done = e1000_get_cfg_done_ich8lan; + phy->ops.set_page = e1000_set_page_igp; + phy->ops.read_reg = e1000_read_phy_reg_hv; + phy->ops.read_reg_locked = e1000_read_phy_reg_hv_locked; + phy->ops.read_reg_page = e1000_read_phy_reg_page_hv; + phy->ops.release = e1000_release_swflag_ich8lan; + phy->ops.reset = e1000_phy_hw_reset_ich8lan; + phy->ops.set_d0_lplu_state = e1000_set_lplu_state_pchlan; + phy->ops.set_d3_lplu_state = e1000_set_lplu_state_pchlan; + phy->ops.write_reg = e1000_write_phy_reg_hv; + phy->ops.write_reg_locked = e1000_write_phy_reg_hv_locked; + phy->ops.write_reg_page = e1000_write_phy_reg_page_hv; + phy->ops.power_up = e1000_power_up_phy_copper; + phy->ops.power_down = e1000_power_down_phy_copper_ich8lan; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + + phy->id = e1000_phy_unknown; + + ret_val = e1000_init_phy_workarounds_pchlan(hw); + if (ret_val) + return ret_val; + + if (phy->id == e1000_phy_unknown) + switch (hw->mac.type) { + default: + ret_val = e1000_get_phy_id(hw); + if (ret_val) + return ret_val; + if ((phy->id != 0) && (phy->id != PHY_REVISION_MASK)) + break; + /* fall-through */ + case e1000_pch2lan: + case e1000_pch_lpt: + /* In case the PHY needs to be in mdio slow mode, + * set slow mode and try to get the PHY id again. + */ + ret_val = e1000_set_mdio_slow_mode_hv(hw); + if (ret_val) + return ret_val; + ret_val = e1000_get_phy_id(hw); + if (ret_val) + return ret_val; + break; + } + phy->type = e1000_get_phy_type_from_id(phy->id); + + switch (phy->type) { + case e1000_phy_82577: + case e1000_phy_82579: + case e1000_phy_i217: + phy->ops.check_polarity = e1000_check_polarity_82577; + phy->ops.force_speed_duplex = + e1000_phy_force_speed_duplex_82577; + phy->ops.get_cable_length = e1000_get_cable_length_82577; + phy->ops.get_info = e1000_get_phy_info_82577; + phy->ops.commit = e1000_phy_sw_reset_generic; + break; + case e1000_phy_82578: + phy->ops.check_polarity = e1000_check_polarity_m88; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; + phy->ops.get_cable_length = e1000_get_cable_length_m88; + phy->ops.get_info = e1000_get_phy_info_m88; + break; + default: + ret_val = -E1000_ERR_PHY; + break; + } + + return ret_val; +} + +/** + * e1000_init_phy_params_ich8lan - Initialize PHY function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific PHY parameters and function pointers. + **/ +STATIC s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 i = 0; + + DEBUGFUNC("e1000_init_phy_params_ich8lan"); + + phy->addr = 1; + phy->reset_delay_us = 100; + + phy->ops.acquire = e1000_acquire_swflag_ich8lan; + phy->ops.check_reset_block = e1000_check_reset_block_ich8lan; + phy->ops.get_cable_length = e1000_get_cable_length_igp_2; + phy->ops.get_cfg_done = e1000_get_cfg_done_ich8lan; + phy->ops.read_reg = e1000_read_phy_reg_igp; + phy->ops.release = e1000_release_swflag_ich8lan; + phy->ops.reset = e1000_phy_hw_reset_ich8lan; + phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_ich8lan; + phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_ich8lan; + phy->ops.write_reg = e1000_write_phy_reg_igp; + phy->ops.power_up = e1000_power_up_phy_copper; + phy->ops.power_down = e1000_power_down_phy_copper_ich8lan; + + /* We may need to do this twice - once for IGP and if that fails, + * we'll set BM func pointers and try again + */ + ret_val = e1000_determine_phy_address(hw); + if (ret_val) { + phy->ops.write_reg = e1000_write_phy_reg_bm; + phy->ops.read_reg = e1000_read_phy_reg_bm; + ret_val = e1000_determine_phy_address(hw); + if (ret_val) { + DEBUGOUT("Cannot determine PHY addr. Erroring out\n"); + return ret_val; + } + } + + phy->id = 0; + while ((e1000_phy_unknown == e1000_get_phy_type_from_id(phy->id)) && + (i++ < 100)) { + msec_delay(1); + ret_val = e1000_get_phy_id(hw); + if (ret_val) + return ret_val; + } + + /* Verify phy id */ + switch (phy->id) { + case IGP03E1000_E_PHY_ID: + phy->type = e1000_phy_igp_3; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->ops.read_reg_locked = e1000_read_phy_reg_igp_locked; + phy->ops.write_reg_locked = e1000_write_phy_reg_igp_locked; + phy->ops.get_info = e1000_get_phy_info_igp; + phy->ops.check_polarity = e1000_check_polarity_igp; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_igp; + break; + case IFE_E_PHY_ID: + case IFE_PLUS_E_PHY_ID: + case IFE_C_E_PHY_ID: + phy->type = e1000_phy_ife; + phy->autoneg_mask = E1000_ALL_NOT_GIG; + phy->ops.get_info = e1000_get_phy_info_ife; + phy->ops.check_polarity = e1000_check_polarity_ife; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_ife; + break; + case BME1000_E_PHY_ID: + phy->type = e1000_phy_bm; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->ops.read_reg = e1000_read_phy_reg_bm; + phy->ops.write_reg = e1000_write_phy_reg_bm; + phy->ops.commit = e1000_phy_sw_reset_generic; + phy->ops.get_info = e1000_get_phy_info_m88; + phy->ops.check_polarity = e1000_check_polarity_m88; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; + break; + default: + return -E1000_ERR_PHY; + break; + } + + return E1000_SUCCESS; +} + +/** + * e1000_init_nvm_params_ich8lan - Initialize NVM function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific NVM parameters and function + * pointers. + **/ +STATIC s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 gfpreg, sector_base_addr, sector_end_addr; + u16 i; + + DEBUGFUNC("e1000_init_nvm_params_ich8lan"); + + /* Can't read flash registers if the register set isn't mapped. */ + nvm->type = e1000_nvm_flash_sw; + if (!hw->flash_address) { + DEBUGOUT("ERROR: Flash registers not mapped\n"); + return -E1000_ERR_CONFIG; + } + + gfpreg = E1000_READ_FLASH_REG(hw, ICH_FLASH_GFPREG); + + /* sector_X_addr is a "sector"-aligned address (4096 bytes) + * Add 1 to sector_end_addr since this sector is included in + * the overall size. + */ + sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK; + sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1; + + /* flash_base_addr is byte-aligned */ + nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT; + + /* find total size of the NVM, then cut in half since the total + * size represents two separate NVM banks. + */ + nvm->flash_bank_size = ((sector_end_addr - sector_base_addr) + << FLASH_SECTOR_ADDR_SHIFT); + nvm->flash_bank_size /= 2; + /* Adjust to word count */ + nvm->flash_bank_size /= sizeof(u16); + + nvm->word_size = E1000_SHADOW_RAM_WORDS; + + /* Clear shadow ram */ + for (i = 0; i < nvm->word_size; i++) { + dev_spec->shadow_ram[i].modified = false; + dev_spec->shadow_ram[i].value = 0xFFFF; + } + + E1000_MUTEX_INIT(&dev_spec->nvm_mutex); + E1000_MUTEX_INIT(&dev_spec->swflag_mutex); + + /* Function Pointers */ + nvm->ops.acquire = e1000_acquire_nvm_ich8lan; + nvm->ops.release = e1000_release_nvm_ich8lan; + nvm->ops.read = e1000_read_nvm_ich8lan; + nvm->ops.update = e1000_update_nvm_checksum_ich8lan; + nvm->ops.valid_led_default = e1000_valid_led_default_ich8lan; + nvm->ops.validate = e1000_validate_nvm_checksum_ich8lan; + nvm->ops.write = e1000_write_nvm_ich8lan; + + return E1000_SUCCESS; +} + +/** + * e1000_init_mac_params_ich8lan - Initialize MAC function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific MAC parameters and function + * pointers. + **/ +STATIC s32 e1000_init_mac_params_ich8lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; +#if defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT) + u16 pci_cfg; +#endif /* QV_RELEASE || !defined(NO_PCH_LPT_B0_SUPPORT) */ + + DEBUGFUNC("e1000_init_mac_params_ich8lan"); + + /* Set media type function pointer */ + hw->phy.media_type = e1000_media_type_copper; + + /* Set mta register count */ + mac->mta_reg_count = 32; + /* Set rar entry count */ + mac->rar_entry_count = E1000_ICH_RAR_ENTRIES; + if (mac->type == e1000_ich8lan) + mac->rar_entry_count--; + /* Set if part includes ASF firmware */ + mac->asf_firmware_present = true; + /* FWSM register */ + mac->has_fwsm = true; + /* ARC subsystem not supported */ + mac->arc_subsystem_valid = false; + /* Adaptive IFS supported */ + mac->adaptive_ifs = true; + + /* Function pointers */ + + /* bus type/speed/width */ + mac->ops.get_bus_info = e1000_get_bus_info_ich8lan; + /* function id */ + mac->ops.set_lan_id = e1000_set_lan_id_single_port; + /* reset */ + mac->ops.reset_hw = e1000_reset_hw_ich8lan; + /* hw initialization */ + mac->ops.init_hw = e1000_init_hw_ich8lan; + /* link setup */ + mac->ops.setup_link = e1000_setup_link_ich8lan; + /* physical interface setup */ + mac->ops.setup_physical_interface = e1000_setup_copper_link_ich8lan; + /* check for link */ + mac->ops.check_for_link = e1000_check_for_copper_link_ich8lan; + /* link info */ + mac->ops.get_link_up_info = e1000_get_link_up_info_ich8lan; + /* multicast address update */ + mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; + /* clear hardware counters */ + mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan; + + /* LED and other operations */ + switch (mac->type) { + case e1000_ich8lan: + case e1000_ich9lan: + case e1000_ich10lan: + /* check management mode */ + mac->ops.check_mng_mode = e1000_check_mng_mode_ich8lan; + /* ID LED init */ + mac->ops.id_led_init = e1000_id_led_init_generic; + /* blink LED */ + mac->ops.blink_led = e1000_blink_led_generic; + /* setup LED */ + mac->ops.setup_led = e1000_setup_led_generic; + /* cleanup LED */ + mac->ops.cleanup_led = e1000_cleanup_led_ich8lan; + /* turn on/off LED */ + mac->ops.led_on = e1000_led_on_ich8lan; + mac->ops.led_off = e1000_led_off_ich8lan; + break; + case e1000_pch2lan: + mac->rar_entry_count = E1000_PCH2_RAR_ENTRIES; + mac->ops.rar_set = e1000_rar_set_pch2lan; + /* fall-through */ + case e1000_pch_lpt: +#ifndef NO_NON_BLOCKING_PHY_MTA_UPDATE_SUPPORT + /* multicast address update for pch2 */ + mac->ops.update_mc_addr_list = + e1000_update_mc_addr_list_pch2lan; + /* fall-through */ +#endif + case e1000_pchlan: +#if defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT) + /* save PCH revision_id */ + e1000_read_pci_cfg(hw, E1000_PCI_REVISION_ID_REG, &pci_cfg); + hw->revision_id = (u8)(pci_cfg &= 0x000F); +#endif /* QV_RELEASE || !defined(NO_PCH_LPT_B0_SUPPORT) */ + /* check management mode */ + mac->ops.check_mng_mode = e1000_check_mng_mode_pchlan; + /* ID LED init */ + mac->ops.id_led_init = e1000_id_led_init_pchlan; + /* setup LED */ + mac->ops.setup_led = e1000_setup_led_pchlan; + /* cleanup LED */ + mac->ops.cleanup_led = e1000_cleanup_led_pchlan; + /* turn on/off LED */ + mac->ops.led_on = e1000_led_on_pchlan; + mac->ops.led_off = e1000_led_off_pchlan; + break; + default: + break; + } + + if (mac->type == e1000_pch_lpt) { + mac->rar_entry_count = E1000_PCH_LPT_RAR_ENTRIES; + mac->ops.rar_set = e1000_rar_set_pch_lpt; + mac->ops.setup_physical_interface = e1000_setup_copper_link_pch_lpt; + } + + /* Enable PCS Lock-loss workaround for ICH8 */ + if (mac->type == e1000_ich8lan) + e1000_set_kmrn_lock_loss_workaround_ich8lan(hw, true); + + return E1000_SUCCESS; +} + +/** + * __e1000_access_emi_reg_locked - Read/write EMI register + * @hw: pointer to the HW structure + * @addr: EMI address to program + * @data: pointer to value to read/write from/to the EMI address + * @read: boolean flag to indicate read or write + * + * This helper function assumes the SW/FW/HW Semaphore is already acquired. + **/ +STATIC s32 __e1000_access_emi_reg_locked(struct e1000_hw *hw, u16 address, + u16 *data, bool read) +{ + s32 ret_val; + + DEBUGFUNC("__e1000_access_emi_reg_locked"); + + ret_val = hw->phy.ops.write_reg_locked(hw, I82579_EMI_ADDR, address); + if (ret_val) + return ret_val; + + if (read) + ret_val = hw->phy.ops.read_reg_locked(hw, I82579_EMI_DATA, + data); + else + ret_val = hw->phy.ops.write_reg_locked(hw, I82579_EMI_DATA, + *data); + + return ret_val; +} + +/** + * e1000_read_emi_reg_locked - Read Extended Management Interface register + * @hw: pointer to the HW structure + * @addr: EMI address to program + * @data: value to be read from the EMI address + * + * Assumes the SW/FW/HW Semaphore is already acquired. + **/ +s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data) +{ + DEBUGFUNC("e1000_read_emi_reg_locked"); + + return __e1000_access_emi_reg_locked(hw, addr, data, true); +} + +/** + * e1000_write_emi_reg_locked - Write Extended Management Interface register + * @hw: pointer to the HW structure + * @addr: EMI address to program + * @data: value to be written to the EMI address + * + * Assumes the SW/FW/HW Semaphore is already acquired. + **/ +s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data) +{ + DEBUGFUNC("e1000_read_emi_reg_locked"); + + return __e1000_access_emi_reg_locked(hw, addr, &data, false); +} + +/** + * e1000_set_eee_pchlan - Enable/disable EEE support + * @hw: pointer to the HW structure + * + * Enable/disable EEE based on setting in dev_spec structure, the duplex of + * the link and the EEE capabilities of the link partner. The LPI Control + * register bits will remain set only if/when link is up. + * + * EEE LPI must not be asserted earlier than one second after link is up. + * On 82579, EEE LPI should not be enabled until such time otherwise there + * can be link issues with some switches. Other devices can have EEE LPI + * enabled immediately upon link up since they have a timer in hardware which + * prevents LPI from being asserted too early. + **/ +s32 e1000_set_eee_pchlan(struct e1000_hw *hw) +{ + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + s32 ret_val; + u16 lpa, pcs_status, adv, adv_addr, lpi_ctrl, data; + + DEBUGFUNC("e1000_set_eee_pchlan"); + + switch (hw->phy.type) { + case e1000_phy_82579: + lpa = I82579_EEE_LP_ABILITY; + pcs_status = I82579_EEE_PCS_STATUS; + adv_addr = I82579_EEE_ADVERTISEMENT; + break; + case e1000_phy_i217: + lpa = I217_EEE_LP_ABILITY; + pcs_status = I217_EEE_PCS_STATUS; + adv_addr = I217_EEE_ADVERTISEMENT; + break; + default: + return E1000_SUCCESS; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + + ret_val = hw->phy.ops.read_reg_locked(hw, I82579_LPI_CTRL, &lpi_ctrl); + if (ret_val) + goto release; + + /* Clear bits that enable EEE in various speeds */ + lpi_ctrl &= ~I82579_LPI_CTRL_ENABLE_MASK; + + /* Enable EEE if not disabled by user */ + if (!dev_spec->eee_disable) { + /* Save off link partner's EEE ability */ + ret_val = e1000_read_emi_reg_locked(hw, lpa, + &dev_spec->eee_lp_ability); + if (ret_val) + goto release; + + /* Read EEE advertisement */ + ret_val = e1000_read_emi_reg_locked(hw, adv_addr, &adv); + if (ret_val) + goto release; + + /* Enable EEE only for speeds in which the link partner is + * EEE capable and for which we advertise EEE. + */ + if (adv & dev_spec->eee_lp_ability & I82579_EEE_1000_SUPPORTED) + lpi_ctrl |= I82579_LPI_CTRL_1000_ENABLE; + + if (adv & dev_spec->eee_lp_ability & I82579_EEE_100_SUPPORTED) { + hw->phy.ops.read_reg_locked(hw, PHY_LP_ABILITY, &data); + if (data & NWAY_LPAR_100TX_FD_CAPS) + lpi_ctrl |= I82579_LPI_CTRL_100_ENABLE; + else + /* EEE is not supported in 100Half, so ignore + * partner's EEE in 100 ability if full-duplex + * is not advertised. + */ + dev_spec->eee_lp_ability &= + ~I82579_EEE_100_SUPPORTED; + } + } + + if (hw->phy.type == e1000_phy_82579) { + ret_val = e1000_read_emi_reg_locked(hw, I82579_LPI_PLL_SHUT, + &data); + if (ret_val) + goto release; + + data &= ~I82579_LPI_100_PLL_SHUT; + ret_val = e1000_write_emi_reg_locked(hw, I82579_LPI_PLL_SHUT, + data); + } + + /* R/Clr IEEE MMD 3.1 bits 11:10 - Tx/Rx LPI Received */ + ret_val = e1000_read_emi_reg_locked(hw, pcs_status, &data); + if (ret_val) + goto release; + + ret_val = hw->phy.ops.write_reg_locked(hw, I82579_LPI_CTRL, lpi_ctrl); +release: + hw->phy.ops.release(hw); + + return ret_val; +} + +/** + * e1000_k1_workaround_lpt_lp - K1 workaround on Lynxpoint-LP + * @hw: pointer to the HW structure + * @link: link up bool flag + * + * When K1 is enabled for 1Gbps, the MAC can miss 2 DMA completion indications + * preventing further DMA write requests. Workaround the issue by disabling + * the de-assertion of the clock request when in 1Gpbs mode. + * Also, set appropriate Tx re-transmission timeouts for 10 and 100Half link + * speeds in order to avoid Tx hangs. + **/ +STATIC s32 e1000_k1_workaround_lpt_lp(struct e1000_hw *hw, bool link) +{ + u32 fextnvm6 = E1000_READ_REG(hw, E1000_FEXTNVM6); + u32 status = E1000_READ_REG(hw, E1000_STATUS); + s32 ret_val = E1000_SUCCESS; + u16 reg; + + if (link && (status & E1000_STATUS_SPEED_1000)) { + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + + ret_val = + e1000_read_kmrn_reg_locked(hw, E1000_KMRNCTRLSTA_K1_CONFIG, + ®); + if (ret_val) + goto release; + + ret_val = + e1000_write_kmrn_reg_locked(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + reg & + ~E1000_KMRNCTRLSTA_K1_ENABLE); + if (ret_val) + goto release; + + usec_delay(10); + + E1000_WRITE_REG(hw, E1000_FEXTNVM6, + fextnvm6 | E1000_FEXTNVM6_REQ_PLL_CLK); + + ret_val = + e1000_write_kmrn_reg_locked(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + reg); +release: + hw->phy.ops.release(hw); + } else { + /* clear FEXTNVM6 bit 8 on link down or 10/100 */ + fextnvm6 &= ~E1000_FEXTNVM6_REQ_PLL_CLK; + + if (!link || ((status & E1000_STATUS_SPEED_100) && + (status & E1000_STATUS_FD))) + goto update_fextnvm6; + + ret_val = hw->phy.ops.read_reg(hw, I217_INBAND_CTRL, ®); + if (ret_val) + return ret_val; + + /* Clear link status transmit timeout */ + reg &= ~I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_MASK; + + if (status & E1000_STATUS_SPEED_100) { + /* Set inband Tx timeout to 5x10us for 100Half */ + reg |= 5 << I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_SHIFT; + + /* Do not extend the K1 entry latency for 100Half */ + fextnvm6 &= ~E1000_FEXTNVM6_ENABLE_K1_ENTRY_CONDITION; + } else { + /* Set inband Tx timeout to 50x10us for 10Full/Half */ + reg |= 50 << + I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_SHIFT; + + /* Extend the K1 entry latency for 10 Mbps */ + fextnvm6 |= E1000_FEXTNVM6_ENABLE_K1_ENTRY_CONDITION; + } + + ret_val = hw->phy.ops.write_reg(hw, I217_INBAND_CTRL, reg); + if (ret_val) + return ret_val; + +update_fextnvm6: + E1000_WRITE_REG(hw, E1000_FEXTNVM6, fextnvm6); + } + + return ret_val; +} + +#ifdef ULP_SUPPORT +/** + * e1000_enable_ulp_lpt_lp - configure Ultra Low Power mode for LynxPoint-LP + * @hw: pointer to the HW structure + * @to_sx: boolean indicating a system power state transition to Sx + * + * When link is down, configure ULP mode to significantly reduce the power + * to the PHY. If on a Manageability Engine (ME) enabled system, tell the + * ME firmware to start the ULP configuration. If not on an ME enabled + * system, configure the ULP mode by software. + */ +s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx) +{ + u32 mac_reg; + s32 ret_val = E1000_SUCCESS; + u16 phy_reg; + + if ((hw->mac.type < e1000_pch_lpt) || + (hw->device_id == E1000_DEV_ID_PCH_LPT_I217_LM) || + (hw->device_id == E1000_DEV_ID_PCH_LPT_I217_V) || + (hw->device_id == E1000_DEV_ID_PCH_I218_LM2) || + (hw->device_id == E1000_DEV_ID_PCH_I218_V2) || + (hw->dev_spec.ich8lan.ulp_state == e1000_ulp_state_on)) + return 0; + + if (!to_sx) { + int i = 0; + /* Poll up to 5 seconds for Cable Disconnected indication */ + while (!(E1000_READ_REG(hw, E1000_FEXT) & + E1000_FEXT_PHY_CABLE_DISCONNECTED)) { + /* Bail if link is re-acquired */ + if (E1000_READ_REG(hw, E1000_STATUS) & E1000_STATUS_LU) + return -E1000_ERR_PHY; + if (i++ == 100) + break; + + msec_delay(50); + } + DEBUGOUT2("CABLE_DISCONNECTED %s set after %dmsec\n", + (E1000_READ_REG(hw, E1000_FEXT) & + E1000_FEXT_PHY_CABLE_DISCONNECTED) ? "" : "not", + i * 50); + if (!(E1000_READ_REG(hw, E1000_FEXT) & + E1000_FEXT_PHY_CABLE_DISCONNECTED)) + return 0; + } + + if (E1000_READ_REG(hw, E1000_FWSM) & E1000_ICH_FWSM_FW_VALID) { + /* Request ME configure ULP mode in the PHY */ + mac_reg = E1000_READ_REG(hw, E1000_H2ME); + mac_reg |= E1000_H2ME_ULP | E1000_H2ME_ENFORCE_SETTINGS; + E1000_WRITE_REG(hw, E1000_H2ME, mac_reg); + + goto out; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + /* During S0 Idle keep the phy in PCI-E mode */ + if (hw->dev_spec.ich8lan.smbus_disable) + goto skip_smbus; + + /* Force SMBus mode in PHY */ + ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, &phy_reg); + if (ret_val) + goto release; + phy_reg |= CV_SMB_CTRL_FORCE_SMBUS; + e1000_write_phy_reg_hv_locked(hw, CV_SMB_CTRL, phy_reg); + + /* Force SMBus mode in MAC */ + mac_reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + mac_reg |= E1000_CTRL_EXT_FORCE_SMBUS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, mac_reg); + +skip_smbus: + if (!to_sx) { + /* Change the 'Link Status Change' interrupt to trigger + * on 'Cable Status Change' + */ + ret_val = e1000_read_kmrn_reg_locked(hw, + E1000_KMRNCTRLSTA_OP_MODES, + &phy_reg); + if (ret_val) + goto release; + phy_reg |= E1000_KMRNCTRLSTA_OP_MODES_LSC2CSC; + e1000_write_kmrn_reg_locked(hw, E1000_KMRNCTRLSTA_OP_MODES, + phy_reg); + } + + /* Set Inband ULP Exit, Reset to SMBus mode and + * Disable SMBus Release on PERST# in PHY + */ + ret_val = e1000_read_phy_reg_hv_locked(hw, I218_ULP_CONFIG1, &phy_reg); + if (ret_val) + goto release; + phy_reg |= (I218_ULP_CONFIG1_RESET_TO_SMBUS | + I218_ULP_CONFIG1_DISABLE_SMB_PERST); + if (to_sx) { + if (E1000_READ_REG(hw, E1000_WUFC) & E1000_WUFC_LNKC) + phy_reg |= I218_ULP_CONFIG1_WOL_HOST; + else + phy_reg &= ~I218_ULP_CONFIG1_WOL_HOST; + + phy_reg |= I218_ULP_CONFIG1_STICKY_ULP; + phy_reg &= ~I218_ULP_CONFIG1_INBAND_EXIT; + } else { + phy_reg |= I218_ULP_CONFIG1_INBAND_EXIT; + phy_reg &= ~I218_ULP_CONFIG1_STICKY_ULP; + phy_reg &= ~I218_ULP_CONFIG1_WOL_HOST; + } + e1000_write_phy_reg_hv_locked(hw, I218_ULP_CONFIG1, phy_reg); + + /* Set Disable SMBus Release on PERST# in MAC */ + mac_reg = E1000_READ_REG(hw, E1000_FEXTNVM7); + mac_reg |= E1000_FEXTNVM7_DISABLE_SMB_PERST; + E1000_WRITE_REG(hw, E1000_FEXTNVM7, mac_reg); + + /* Commit ULP changes in PHY by starting auto ULP configuration */ + phy_reg |= I218_ULP_CONFIG1_START; + e1000_write_phy_reg_hv_locked(hw, I218_ULP_CONFIG1, phy_reg); + + if (!to_sx) { + /* Disable Tx so that the MAC doesn't send any (buffered) + * packets to the PHY. + */ + mac_reg = E1000_READ_REG(hw, E1000_TCTL); + mac_reg &= ~E1000_TCTL_EN; + E1000_WRITE_REG(hw, E1000_TCTL, mac_reg); + } + +release: + hw->phy.ops.release(hw); +out: + if (ret_val) + DEBUGOUT1("Error in ULP enable flow: %d\n", ret_val); + else + hw->dev_spec.ich8lan.ulp_state = e1000_ulp_state_on; + + return ret_val; +} + +/** + * e1000_disable_ulp_lpt_lp - unconfigure Ultra Low Power mode for LynxPoint-LP + * @hw: pointer to the HW structure + * @force: boolean indicating whether or not to force disabling ULP + * + * Un-configure ULP mode when link is up, the system is transitioned from + * Sx or the driver is unloaded. If on a Manageability Engine (ME) enabled + * system, poll for an indication from ME that ULP has been un-configured. + * If not on an ME enabled system, un-configure the ULP mode by software. + * + * During nominal operation, this function is called when link is acquired + * to disable ULP mode (force=false); otherwise, for example when unloading + * the driver or during Sx->S0 transitions, this is called with force=true + * to forcibly disable ULP. + + * When the cable is plugged in while the device is in D0, a Cable Status + * Change interrupt is generated which causes this function to be called + * to partially disable ULP mode and restart autonegotiation. This function + * is then called again due to the resulting Link Status Change interrupt + * to finish cleaning up after the ULP flow. + */ +s32 e1000_disable_ulp_lpt_lp(struct e1000_hw *hw, bool force) +{ + s32 ret_val = E1000_SUCCESS; + u32 mac_reg; + u16 phy_reg; + int i = 0; + + if ((hw->mac.type < e1000_pch_lpt) || + (hw->device_id == E1000_DEV_ID_PCH_LPT_I217_LM) || + (hw->device_id == E1000_DEV_ID_PCH_LPT_I217_V) || + (hw->device_id == E1000_DEV_ID_PCH_I218_LM2) || + (hw->device_id == E1000_DEV_ID_PCH_I218_V2) || + (hw->dev_spec.ich8lan.ulp_state == e1000_ulp_state_off)) + return 0; + + if (E1000_READ_REG(hw, E1000_FWSM) & E1000_ICH_FWSM_FW_VALID) { + if (force) { + /* Request ME un-configure ULP mode in the PHY */ + mac_reg = E1000_READ_REG(hw, E1000_H2ME); + mac_reg &= ~E1000_H2ME_ULP; + mac_reg |= E1000_H2ME_ENFORCE_SETTINGS; + E1000_WRITE_REG(hw, E1000_H2ME, mac_reg); + } + + /* Poll up to 100msec for ME to clear ULP_CFG_DONE */ + while (E1000_READ_REG(hw, E1000_FWSM) & + E1000_FWSM_ULP_CFG_DONE) { + if (i++ == 10) { + ret_val = -E1000_ERR_PHY; + goto out; + } + + msec_delay(10); + } + DEBUGOUT1("ULP_CONFIG_DONE cleared after %dmsec\n", i * 10); + + if (force) { + mac_reg = E1000_READ_REG(hw, E1000_H2ME); + mac_reg &= ~E1000_H2ME_ENFORCE_SETTINGS; + E1000_WRITE_REG(hw, E1000_H2ME, mac_reg); + } else { + /* Clear H2ME.ULP after ME ULP configuration */ + mac_reg = E1000_READ_REG(hw, E1000_H2ME); + mac_reg &= ~E1000_H2ME_ULP; + E1000_WRITE_REG(hw, E1000_H2ME, mac_reg); + + /* Restore link speed advertisements and restart + * Auto-negotiation + */ + if (hw->mac.autoneg) { + ret_val = e1000_phy_setup_autoneg(hw); + if (ret_val) + goto out; + } else { + ret_val = e1000_setup_copper_link_generic(hw); + if (ret_val) + goto out; + } + ret_val = e1000_oem_bits_config_ich8lan(hw, true); + } + + goto out; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + /* Revert the change to the 'Link Status Change' + * interrupt to trigger on 'Cable Status Change' + */ + ret_val = e1000_read_kmrn_reg_locked(hw, E1000_KMRNCTRLSTA_OP_MODES, + &phy_reg); + if (ret_val) + goto release; + phy_reg &= ~E1000_KMRNCTRLSTA_OP_MODES_LSC2CSC; + e1000_write_kmrn_reg_locked(hw, E1000_KMRNCTRLSTA_OP_MODES, phy_reg); + + if (force) + /* Toggle LANPHYPC Value bit */ + e1000_toggle_lanphypc_pch_lpt(hw); + + /* Unforce SMBus mode in PHY */ + ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, &phy_reg); + if (ret_val) { + /* The MAC might be in PCIe mode, so temporarily force to + * SMBus mode in order to access the PHY. + */ + mac_reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + mac_reg |= E1000_CTRL_EXT_FORCE_SMBUS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, mac_reg); + + msec_delay(50); + + ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, + &phy_reg); + if (ret_val) + goto release; + } + phy_reg &= ~CV_SMB_CTRL_FORCE_SMBUS; + e1000_write_phy_reg_hv_locked(hw, CV_SMB_CTRL, phy_reg); + + /* Unforce SMBus mode in MAC */ + mac_reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, mac_reg); + + /* When ULP mode was previously entered, K1 was disabled by the + * hardware. Re-Enable K1 in the PHY when exiting ULP. + */ + ret_val = e1000_read_phy_reg_hv_locked(hw, HV_PM_CTRL, &phy_reg); + if (ret_val) + goto release; + phy_reg |= HV_PM_CTRL_K1_ENABLE; + e1000_write_phy_reg_hv_locked(hw, HV_PM_CTRL, phy_reg); + + /* Clear ULP enabled configuration */ + ret_val = e1000_read_phy_reg_hv_locked(hw, I218_ULP_CONFIG1, &phy_reg); + if (ret_val) + goto release; + /* CSC interrupt received due to ULP Indication */ + if ((phy_reg & I218_ULP_CONFIG1_IND) || force) { + phy_reg &= ~(I218_ULP_CONFIG1_IND | + I218_ULP_CONFIG1_STICKY_ULP | + I218_ULP_CONFIG1_RESET_TO_SMBUS | + I218_ULP_CONFIG1_WOL_HOST | + I218_ULP_CONFIG1_INBAND_EXIT | + I218_ULP_CONFIG1_DISABLE_SMB_PERST); + e1000_write_phy_reg_hv_locked(hw, I218_ULP_CONFIG1, phy_reg); + + /* Commit ULP changes by starting auto ULP configuration */ + phy_reg |= I218_ULP_CONFIG1_START; + e1000_write_phy_reg_hv_locked(hw, I218_ULP_CONFIG1, phy_reg); + + /* Clear Disable SMBus Release on PERST# in MAC */ + mac_reg = E1000_READ_REG(hw, E1000_FEXTNVM7); + mac_reg &= ~E1000_FEXTNVM7_DISABLE_SMB_PERST; + E1000_WRITE_REG(hw, E1000_FEXTNVM7, mac_reg); + + if (!force) { + hw->phy.ops.release(hw); + + if (hw->mac.autoneg) + e1000_phy_setup_autoneg(hw); + + e1000_sw_lcd_config_ich8lan(hw); + + e1000_oem_bits_config_ich8lan(hw, true); + + /* Set ULP state to unknown and return non-zero to + * indicate no link (yet) and re-enter on the next LSC + * to finish disabling ULP flow. + */ + hw->dev_spec.ich8lan.ulp_state = + e1000_ulp_state_unknown; + + return 1; + } + } + + /* Re-enable Tx */ + mac_reg = E1000_READ_REG(hw, E1000_TCTL); + mac_reg |= E1000_TCTL_EN; + E1000_WRITE_REG(hw, E1000_TCTL, mac_reg); + +release: + hw->phy.ops.release(hw); + if (force) { + hw->phy.ops.reset(hw); + msec_delay(50); + } +out: + if (ret_val) + DEBUGOUT1("Error in ULP disable flow: %d\n", ret_val); + else + hw->dev_spec.ich8lan.ulp_state = e1000_ulp_state_off; + + return ret_val; +} + +#endif /* ULP_SUPPORT */ +/** + * e1000_check_for_copper_link_ich8lan - Check for link (Copper) + * @hw: pointer to the HW structure + * + * Checks to see of the link status of the hardware has changed. If a + * change in link status has been detected, then we read the PHY registers + * to get the current speed/duplex if link exists. + **/ +STATIC s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val, tipg_reg = 0; + u16 emi_addr, emi_val = 0; + bool link = false; + u16 phy_reg; + + DEBUGFUNC("e1000_check_for_copper_link_ich8lan"); + + /* We only want to go out to the PHY registers to see if Auto-Neg + * has completed and/or if our link status has changed. The + * get_link_status flag is set upon receiving a Link Status + * Change or Rx Sequence Error interrupt. + */ + if (!mac->get_link_status) + return E1000_SUCCESS; + + if ((hw->mac.type < e1000_pch_lpt) || + (hw->device_id == E1000_DEV_ID_PCH_LPT_I217_LM) || + (hw->device_id == E1000_DEV_ID_PCH_LPT_I217_V)) { + /* First we want to see if the MII Status Register reports + * link. If so, then we want to get the current speed/duplex + * of the PHY. + */ + ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + return ret_val; + } else { + /* Check the MAC's STATUS register to determine link state + * since the PHY could be inaccessible while in ULP mode. + */ + link = !!(E1000_READ_REG(hw, E1000_STATUS) & E1000_STATUS_LU); + if (link) + ret_val = e1000_disable_ulp_lpt_lp(hw, false); + else + ret_val = e1000_enable_ulp_lpt_lp(hw, false); + if (ret_val) + return ret_val; + } + + if (hw->mac.type == e1000_pchlan) { + ret_val = e1000_k1_gig_workaround_hv(hw, link); + if (ret_val) + return ret_val; + } + + /* When connected at 10Mbps half-duplex, some parts are excessively + * aggressive resulting in many collisions. To avoid this, increase + * the IPG and reduce Rx latency in the PHY. + */ + if (((hw->mac.type == e1000_pch2lan) || + (hw->mac.type == e1000_pch_lpt)) && link) { + u16 speed, duplex; + + e1000_get_speed_and_duplex_copper_generic(hw, &speed, &duplex); + tipg_reg = E1000_READ_REG(hw, E1000_TIPG); + tipg_reg &= ~E1000_TIPG_IPGT_MASK; + + if (duplex == HALF_DUPLEX && speed == SPEED_10) { + tipg_reg |= 0xFF; + /* Reduce Rx latency in analog PHY */ + emi_val = 0; + } else { + /* Roll back the default values */ + tipg_reg |= 0x08; + emi_val = 1; + } + + E1000_WRITE_REG(hw, E1000_TIPG, tipg_reg); + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + + if (hw->mac.type == e1000_pch2lan) + emi_addr = I82579_RX_CONFIG; + else + emi_addr = I217_RX_CONFIG; + ret_val = e1000_write_emi_reg_locked(hw, emi_addr, emi_val); + + hw->phy.ops.release(hw); + + if (ret_val) + return ret_val; + } + + /* I217 Packet Loss issue: + * ensure that FEXTNVM4 Beacon Duration is set correctly + * on power up. + * Set the Beacon Duration for I217 to 8 usec + */ + if (hw->mac.type == e1000_pch_lpt) { + u32 mac_reg; + + mac_reg = E1000_READ_REG(hw, E1000_FEXTNVM4); + mac_reg &= ~E1000_FEXTNVM4_BEACON_DURATION_MASK; + mac_reg |= E1000_FEXTNVM4_BEACON_DURATION_8USEC; + E1000_WRITE_REG(hw, E1000_FEXTNVM4, mac_reg); + } + + /* Work-around I218 hang issue */ + if ((hw->device_id == E1000_DEV_ID_PCH_LPTLP_I218_LM) || + (hw->device_id == E1000_DEV_ID_PCH_LPTLP_I218_V) || + (hw->device_id == E1000_DEV_ID_PCH_I218_LM3) || + (hw->device_id == E1000_DEV_ID_PCH_I218_V3)) { + ret_val = e1000_k1_workaround_lpt_lp(hw, link); + if (ret_val) + return ret_val; + } + /* Clear link partner's EEE ability */ + hw->dev_spec.ich8lan.eee_lp_ability = 0; + + /* Configure K0s minimum time */ + if (hw->mac.type == e1000_pch_lpt) { + e1000_configure_k0s_lpt(hw, K1_ENTRY_LATENCY, K1_MIN_TIME); + } + + if (!link) + return E1000_SUCCESS; /* No link detected */ + + mac->get_link_status = false; + + switch (hw->mac.type) { + case e1000_pch2lan: + ret_val = e1000_k1_workaround_lv(hw); + if (ret_val) + return ret_val; + /* fall-thru */ + case e1000_pchlan: + if (hw->phy.type == e1000_phy_82578) { + ret_val = e1000_link_stall_workaround_hv(hw); + if (ret_val) + return ret_val; + } + + /* Workaround for PCHx parts in half-duplex: + * Set the number of preambles removed from the packet + * when it is passed from the PHY to the MAC to prevent + * the MAC from misinterpreting the packet type. + */ + hw->phy.ops.read_reg(hw, HV_KMRN_FIFO_CTRLSTA, &phy_reg); + phy_reg &= ~HV_KMRN_FIFO_CTRLSTA_PREAMBLE_MASK; + + if ((E1000_READ_REG(hw, E1000_STATUS) & E1000_STATUS_FD) != + E1000_STATUS_FD) + phy_reg |= (1 << HV_KMRN_FIFO_CTRLSTA_PREAMBLE_SHIFT); + + hw->phy.ops.write_reg(hw, HV_KMRN_FIFO_CTRLSTA, phy_reg); + break; + default: + break; + } + + /* Check if there was DownShift, must be checked + * immediately after link-up + */ + e1000_check_downshift_generic(hw); + + /* Enable/Disable EEE after link up */ + if (hw->phy.type > e1000_phy_82579) { + ret_val = e1000_set_eee_pchlan(hw); + if (ret_val) + return ret_val; + } + + /* If we are forcing speed/duplex, then we simply return since + * we have already determined whether we have link or not. + */ + if (!mac->autoneg) + return -E1000_ERR_CONFIG; + + /* Auto-Neg is enabled. Auto Speed Detection takes care + * of MAC speed/duplex configuration. So we only need to + * configure Collision Distance in the MAC. + */ + mac->ops.config_collision_dist(hw); + + /* Configure Flow Control now that Auto-Neg has completed. + * First, we need to restore the desired flow control + * settings because we may have had to re-autoneg with a + * different link partner. + */ + ret_val = e1000_config_fc_after_link_up_generic(hw); + if (ret_val) + DEBUGOUT("Error configuring flow control\n"); + + return ret_val; +} + +/** + * e1000_init_function_pointers_ich8lan - Initialize ICH8 function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific function pointers for PHY, MAC, and NVM. + **/ +void e1000_init_function_pointers_ich8lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_init_function_pointers_ich8lan"); + + hw->mac.ops.init_params = e1000_init_mac_params_ich8lan; + hw->nvm.ops.init_params = e1000_init_nvm_params_ich8lan; + switch (hw->mac.type) { + case e1000_ich8lan: + case e1000_ich9lan: + case e1000_ich10lan: + hw->phy.ops.init_params = e1000_init_phy_params_ich8lan; + break; + case e1000_pchlan: + case e1000_pch2lan: + case e1000_pch_lpt: + hw->phy.ops.init_params = e1000_init_phy_params_pchlan; + break; + default: + break; + } +} + +/** + * e1000_acquire_nvm_ich8lan - Acquire NVM mutex + * @hw: pointer to the HW structure + * + * Acquires the mutex for performing NVM operations. + **/ +STATIC s32 e1000_acquire_nvm_ich8lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_acquire_nvm_ich8lan"); + + E1000_MUTEX_LOCK(&hw->dev_spec.ich8lan.nvm_mutex); + + return E1000_SUCCESS; +} + +/** + * e1000_release_nvm_ich8lan - Release NVM mutex + * @hw: pointer to the HW structure + * + * Releases the mutex used while performing NVM operations. + **/ +STATIC void e1000_release_nvm_ich8lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_release_nvm_ich8lan"); + + E1000_MUTEX_UNLOCK(&hw->dev_spec.ich8lan.nvm_mutex); + + return; +} + +/** + * e1000_acquire_swflag_ich8lan - Acquire software control flag + * @hw: pointer to the HW structure + * + * Acquires the software control flag for performing PHY and select + * MAC CSR accesses. + **/ +STATIC s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw) +{ + u32 extcnf_ctrl, timeout = PHY_CFG_TIMEOUT; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_acquire_swflag_ich8lan"); + + E1000_MUTEX_LOCK(&hw->dev_spec.ich8lan.swflag_mutex); + + while (timeout) { + extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)) + break; + + msec_delay_irq(1); + timeout--; + } + + if (!timeout) { + DEBUGOUT("SW has already locked the resource.\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + timeout = SW_FLAG_TIMEOUT; + + extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, E1000_EXTCNF_CTRL, extcnf_ctrl); + + while (timeout) { + extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) + break; + + msec_delay_irq(1); + timeout--; + } + + if (!timeout) { + DEBUGOUT2("Failed to acquire the semaphore, FW or HW has it: FWSM=0x%8.8x EXTCNF_CTRL=0x%8.8x)\n", + E1000_READ_REG(hw, E1000_FWSM), extcnf_ctrl); + extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, E1000_EXTCNF_CTRL, extcnf_ctrl); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + +out: + if (ret_val) + E1000_MUTEX_UNLOCK(&hw->dev_spec.ich8lan.swflag_mutex); + + return ret_val; +} + +/** + * e1000_release_swflag_ich8lan - Release software control flag + * @hw: pointer to the HW structure + * + * Releases the software control flag for performing PHY and select + * MAC CSR accesses. + **/ +STATIC void e1000_release_swflag_ich8lan(struct e1000_hw *hw) +{ + u32 extcnf_ctrl; + + DEBUGFUNC("e1000_release_swflag_ich8lan"); + + extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + + if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) { + extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, E1000_EXTCNF_CTRL, extcnf_ctrl); + } else { + DEBUGOUT("Semaphore unexpectedly released by sw/fw/hw\n"); + } + + E1000_MUTEX_UNLOCK(&hw->dev_spec.ich8lan.swflag_mutex); + + return; +} + +/** + * e1000_check_mng_mode_ich8lan - Checks management mode + * @hw: pointer to the HW structure + * + * This checks if the adapter has any manageability enabled. + * This is a function pointer entry point only called by read/write + * routines for the PHY and NVM parts. + **/ +STATIC bool e1000_check_mng_mode_ich8lan(struct e1000_hw *hw) +{ + u32 fwsm; + + DEBUGFUNC("e1000_check_mng_mode_ich8lan"); + + fwsm = E1000_READ_REG(hw, E1000_FWSM); + + return (fwsm & E1000_ICH_FWSM_FW_VALID) && + ((fwsm & E1000_FWSM_MODE_MASK) == + (E1000_ICH_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)); +} + +/** + * e1000_check_mng_mode_pchlan - Checks management mode + * @hw: pointer to the HW structure + * + * This checks if the adapter has iAMT enabled. + * This is a function pointer entry point only called by read/write + * routines for the PHY and NVM parts. + **/ +STATIC bool e1000_check_mng_mode_pchlan(struct e1000_hw *hw) +{ + u32 fwsm; + + DEBUGFUNC("e1000_check_mng_mode_pchlan"); + + fwsm = E1000_READ_REG(hw, E1000_FWSM); + + return (fwsm & E1000_ICH_FWSM_FW_VALID) && + (fwsm & (E1000_ICH_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)); +} + +/** + * e1000_rar_set_pch2lan - Set receive address register + * @hw: pointer to the HW structure + * @addr: pointer to the receive address + * @index: receive address array register + * + * Sets the receive address array register at index to the address passed + * in by addr. For 82579, RAR[0] is the base address register that is to + * contain the MAC address but RAR[1-6] are reserved for manageability (ME). + * Use SHRA[0-3] in place of those reserved for ME. + **/ +STATIC int e1000_rar_set_pch2lan(struct e1000_hw *hw, u8 *addr, u32 index) +{ + u32 rar_low, rar_high; + + DEBUGFUNC("e1000_rar_set_pch2lan"); + + /* HW expects these in little endian so we reverse the byte order + * from network order (big endian) to little endian + */ + rar_low = ((u32) addr[0] | + ((u32) addr[1] << 8) | + ((u32) addr[2] << 16) | ((u32) addr[3] << 24)); + + rar_high = ((u32) addr[4] | ((u32) addr[5] << 8)); + + /* If MAC address zero, no need to set the AV bit */ + if (rar_low || rar_high) + rar_high |= E1000_RAH_AV; + + if (index == 0) { + E1000_WRITE_REG(hw, E1000_RAL(index), rar_low); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG(hw, E1000_RAH(index), rar_high); + E1000_WRITE_FLUSH(hw); + return E1000_SUCCESS; + } + + /* RAR[1-6] are owned by manageability. Skip those and program the + * next address into the SHRA register array. + */ + if (index < (u32) (hw->mac.rar_entry_count)) { + s32 ret_val; + + ret_val = e1000_acquire_swflag_ich8lan(hw); + if (ret_val) + goto out; + + E1000_WRITE_REG(hw, E1000_SHRAL(index - 1), rar_low); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG(hw, E1000_SHRAH(index - 1), rar_high); + E1000_WRITE_FLUSH(hw); + + e1000_release_swflag_ich8lan(hw); + + /* verify the register updates */ + if ((E1000_READ_REG(hw, E1000_SHRAL(index - 1)) == rar_low) && + (E1000_READ_REG(hw, E1000_SHRAH(index - 1)) == rar_high)) + return E1000_SUCCESS; + + DEBUGOUT2("SHRA[%d] might be locked by ME - FWSM=0x%8.8x\n", + (index - 1), E1000_READ_REG(hw, E1000_FWSM)); + } + +out: + DEBUGOUT1("Failed to write receive address at index %d\n", index); + return -E1000_ERR_CONFIG; +} + +/** + * e1000_rar_set_pch_lpt - Set receive address registers + * @hw: pointer to the HW structure + * @addr: pointer to the receive address + * @index: receive address array register + * + * Sets the receive address register array at index to the address passed + * in by addr. For LPT, RAR[0] is the base address register that is to + * contain the MAC address. SHRA[0-10] are the shared receive address + * registers that are shared between the Host and manageability engine (ME). + **/ +STATIC int e1000_rar_set_pch_lpt(struct e1000_hw *hw, u8 *addr, u32 index) +{ + u32 rar_low, rar_high; + u32 wlock_mac; + + DEBUGFUNC("e1000_rar_set_pch_lpt"); + + /* HW expects these in little endian so we reverse the byte order + * from network order (big endian) to little endian + */ + rar_low = ((u32) addr[0] | ((u32) addr[1] << 8) | + ((u32) addr[2] << 16) | ((u32) addr[3] << 24)); + + rar_high = ((u32) addr[4] | ((u32) addr[5] << 8)); + + /* If MAC address zero, no need to set the AV bit */ + if (rar_low || rar_high) + rar_high |= E1000_RAH_AV; + + if (index == 0) { + E1000_WRITE_REG(hw, E1000_RAL(index), rar_low); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG(hw, E1000_RAH(index), rar_high); + E1000_WRITE_FLUSH(hw); + return E1000_SUCCESS; + } + + /* The manageability engine (ME) can lock certain SHRAR registers that + * it is using - those registers are unavailable for use. + */ + if (index < hw->mac.rar_entry_count) { + wlock_mac = E1000_READ_REG(hw, E1000_FWSM) & + E1000_FWSM_WLOCK_MAC_MASK; + wlock_mac >>= E1000_FWSM_WLOCK_MAC_SHIFT; + + /* Check if all SHRAR registers are locked */ + if (wlock_mac == 1) + goto out; + + if ((wlock_mac == 0) || (index <= wlock_mac)) { + s32 ret_val; + + ret_val = e1000_acquire_swflag_ich8lan(hw); + + if (ret_val) + goto out; + + E1000_WRITE_REG(hw, E1000_SHRAL_PCH_LPT(index - 1), + rar_low); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG(hw, E1000_SHRAH_PCH_LPT(index - 1), + rar_high); + E1000_WRITE_FLUSH(hw); + + e1000_release_swflag_ich8lan(hw); + + /* verify the register updates */ + if ((E1000_READ_REG(hw, E1000_SHRAL_PCH_LPT(index - 1)) == rar_low) && + (E1000_READ_REG(hw, E1000_SHRAH_PCH_LPT(index - 1)) == rar_high)) + return E1000_SUCCESS; + } + } + +out: + DEBUGOUT1("Failed to write receive address at index %d\n", index); + return -E1000_ERR_CONFIG; +} + +#ifndef NO_NON_BLOCKING_PHY_MTA_UPDATE_SUPPORT +/** + * e1000_update_mc_addr_list_pch2lan - Update Multicast addresses + * @hw: pointer to the HW structure + * @mc_addr_list: array of multicast addresses to program + * @mc_addr_count: number of multicast addresses to program + * + * Updates entire Multicast Table Array of the PCH2 MAC and PHY. + * The caller must have a packed mc_addr_list of multicast addresses. + **/ +STATIC void e1000_update_mc_addr_list_pch2lan(struct e1000_hw *hw, + u8 *mc_addr_list, + u32 mc_addr_count) +{ + u16 phy_reg = 0; + int i; + s32 ret_val; + + DEBUGFUNC("e1000_update_mc_addr_list_pch2lan"); + + e1000_update_mc_addr_list_generic(hw, mc_addr_list, mc_addr_count); + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return; + + ret_val = e1000_enable_phy_wakeup_reg_access_bm(hw, &phy_reg); + if (ret_val) + goto release; + + for (i = 0; i < hw->mac.mta_reg_count; i++) { + hw->phy.ops.write_reg_page(hw, BM_MTA(i), + (u16)(hw->mac.mta_shadow[i] & + 0xFFFF)); + hw->phy.ops.write_reg_page(hw, (BM_MTA(i) + 1), + (u16)((hw->mac.mta_shadow[i] >> 16) & + 0xFFFF)); + } + + e1000_disable_phy_wakeup_reg_access_bm(hw, &phy_reg); + +release: + hw->phy.ops.release(hw); +} + +#endif /* NO_NON_BLOCKING_PHY_MTA_UPDATE_SUPPORT */ +/** + * e1000_check_reset_block_ich8lan - Check if PHY reset is blocked + * @hw: pointer to the HW structure + * + * Checks if firmware is blocking the reset of the PHY. + * This is a function pointer entry point only called by + * reset routines. + **/ +STATIC s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw) +{ + u32 fwsm; + bool blocked = false; + int i = 0; + + DEBUGFUNC("e1000_check_reset_block_ich8lan"); + + do { + fwsm = E1000_READ_REG(hw, E1000_FWSM); + if (!(fwsm & E1000_ICH_FWSM_RSPCIPHY)) { + blocked = true; + msec_delay(10); + continue; + } + blocked = false; + } while (blocked && (i++ < 30)); + return blocked ? E1000_BLK_PHY_RESET : E1000_SUCCESS; +} + +/** + * e1000_write_smbus_addr - Write SMBus address to PHY needed during Sx states + * @hw: pointer to the HW structure + * + * Assumes semaphore already acquired. + * + **/ +STATIC s32 e1000_write_smbus_addr(struct e1000_hw *hw) +{ + u16 phy_data; + u32 strap = E1000_READ_REG(hw, E1000_STRAP); + u32 freq = (strap & E1000_STRAP_SMT_FREQ_MASK) >> + E1000_STRAP_SMT_FREQ_SHIFT; + s32 ret_val; + + strap &= E1000_STRAP_SMBUS_ADDRESS_MASK; + + ret_val = e1000_read_phy_reg_hv_locked(hw, HV_SMB_ADDR, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~HV_SMB_ADDR_MASK; + phy_data |= (strap >> E1000_STRAP_SMBUS_ADDRESS_SHIFT); + phy_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID; + + if (hw->phy.type == e1000_phy_i217) { + /* Restore SMBus frequency */ + if (freq--) { + phy_data &= ~HV_SMB_ADDR_FREQ_MASK; + phy_data |= (freq & (1 << 0)) << + HV_SMB_ADDR_FREQ_LOW_SHIFT; + phy_data |= (freq & (1 << 1)) << + (HV_SMB_ADDR_FREQ_HIGH_SHIFT - 1); + } else { + DEBUGOUT("Unsupported SMB frequency in PHY\n"); + } + } + + return e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR, phy_data); +} + +/** + * e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration + * @hw: pointer to the HW structure + * + * SW should configure the LCD from the NVM extended configuration region + * as a workaround for certain parts. + **/ +STATIC s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask; + s32 ret_val = E1000_SUCCESS; + u16 word_addr, reg_data, reg_addr, phy_page = 0; + + DEBUGFUNC("e1000_sw_lcd_config_ich8lan"); + + /* Initialize the PHY from the NVM on ICH platforms. This + * is needed due to an issue where the NVM configuration is + * not properly autoloaded after power transitions. + * Therefore, after each PHY reset, we will load the + * configuration data out of the NVM manually. + */ + switch (hw->mac.type) { + case e1000_ich8lan: + if (phy->type != e1000_phy_igp_3) + return ret_val; + + if ((hw->device_id == E1000_DEV_ID_ICH8_IGP_AMT) || + (hw->device_id == E1000_DEV_ID_ICH8_IGP_C)) { + sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG; + break; + } + /* Fall-thru */ + case e1000_pchlan: + case e1000_pch2lan: + case e1000_pch_lpt: + sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M; + break; + default: + return ret_val; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + + data = E1000_READ_REG(hw, E1000_FEXTNVM); + if (!(data & sw_cfg_mask)) + goto release; + + /* Make sure HW does not configure LCD from PHY + * extended configuration before SW configuration + */ + data = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + if ((hw->mac.type < e1000_pch2lan) && + (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)) + goto release; + + cnf_size = E1000_READ_REG(hw, E1000_EXTCNF_SIZE); + cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK; + cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT; + if (!cnf_size) + goto release; + + cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK; + cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT; + + if (((hw->mac.type == e1000_pchlan) && + !(data & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE)) || + (hw->mac.type > e1000_pchlan)) { + /* HW configures the SMBus address and LEDs when the + * OEM and LCD Write Enable bits are set in the NVM. + * When both NVM bits are cleared, SW will configure + * them instead. + */ + ret_val = e1000_write_smbus_addr(hw); + if (ret_val) + goto release; + + data = E1000_READ_REG(hw, E1000_LEDCTL); + ret_val = e1000_write_phy_reg_hv_locked(hw, HV_LED_CONFIG, + (u16)data); + if (ret_val) + goto release; + } + + /* Configure LCD from extended configuration region. */ + + /* cnf_base_addr is in DWORD */ + word_addr = (u16)(cnf_base_addr << 1); + + for (i = 0; i < cnf_size; i++) { + ret_val = hw->nvm.ops.read(hw, (word_addr + i * 2), 1, + ®_data); + if (ret_val) + goto release; + + ret_val = hw->nvm.ops.read(hw, (word_addr + i * 2 + 1), + 1, ®_addr); + if (ret_val) + goto release; + + /* Save off the PHY page for future writes. */ + if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) { + phy_page = reg_data; + continue; + } + + reg_addr &= PHY_REG_MASK; + reg_addr |= phy_page; + + ret_val = phy->ops.write_reg_locked(hw, (u32)reg_addr, + reg_data); + if (ret_val) + goto release; + } + +release: + hw->phy.ops.release(hw); + return ret_val; +} + +/** + * e1000_k1_gig_workaround_hv - K1 Si workaround + * @hw: pointer to the HW structure + * @link: link up bool flag + * + * If K1 is enabled for 1Gbps, the MAC might stall when transitioning + * from a lower speed. This workaround disables K1 whenever link is at 1Gig + * If link is down, the function will restore the default K1 setting located + * in the NVM. + **/ +STATIC s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link) +{ + s32 ret_val = E1000_SUCCESS; + u16 status_reg = 0; + bool k1_enable = hw->dev_spec.ich8lan.nvm_k1_enabled; + + DEBUGFUNC("e1000_k1_gig_workaround_hv"); + + if (hw->mac.type != e1000_pchlan) + return E1000_SUCCESS; + + /* Wrap the whole flow with the sw flag */ + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + + /* Disable K1 when link is 1Gbps, otherwise use the NVM setting */ + if (link) { + if (hw->phy.type == e1000_phy_82578) { + ret_val = hw->phy.ops.read_reg_locked(hw, BM_CS_STATUS, + &status_reg); + if (ret_val) + goto release; + + status_reg &= (BM_CS_STATUS_LINK_UP | + BM_CS_STATUS_RESOLVED | + BM_CS_STATUS_SPEED_MASK); + + if (status_reg == (BM_CS_STATUS_LINK_UP | + BM_CS_STATUS_RESOLVED | + BM_CS_STATUS_SPEED_1000)) + k1_enable = false; + } + + if (hw->phy.type == e1000_phy_82577) { + ret_val = hw->phy.ops.read_reg_locked(hw, HV_M_STATUS, + &status_reg); + if (ret_val) + goto release; + + status_reg &= (HV_M_STATUS_LINK_UP | + HV_M_STATUS_AUTONEG_COMPLETE | + HV_M_STATUS_SPEED_MASK); + + if (status_reg == (HV_M_STATUS_LINK_UP | + HV_M_STATUS_AUTONEG_COMPLETE | + HV_M_STATUS_SPEED_1000)) + k1_enable = false; + } + + /* Link stall fix for link up */ + ret_val = hw->phy.ops.write_reg_locked(hw, PHY_REG(770, 19), + 0x0100); + if (ret_val) + goto release; + + } else { + /* Link stall fix for link down */ + ret_val = hw->phy.ops.write_reg_locked(hw, PHY_REG(770, 19), + 0x4100); + if (ret_val) + goto release; + } + + ret_val = e1000_configure_k1_ich8lan(hw, k1_enable); + +release: + hw->phy.ops.release(hw); + + return ret_val; +} + +/** + * e1000_configure_k1_ich8lan - Configure K1 power state + * @hw: pointer to the HW structure + * @enable: K1 state to configure + * + * Configure the K1 power state based on the provided parameter. + * Assumes semaphore already acquired. + * + * Success returns 0, Failure returns -E1000_ERR_PHY (-2) + **/ +s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable) +{ + s32 ret_val; + u32 ctrl_reg = 0; + u32 ctrl_ext = 0; + u32 reg = 0; + u16 kmrn_reg = 0; + + DEBUGFUNC("e1000_configure_k1_ich8lan"); + + ret_val = e1000_read_kmrn_reg_locked(hw, E1000_KMRNCTRLSTA_K1_CONFIG, + &kmrn_reg); + if (ret_val) + return ret_val; + + if (k1_enable) + kmrn_reg |= E1000_KMRNCTRLSTA_K1_ENABLE; + else + kmrn_reg &= ~E1000_KMRNCTRLSTA_K1_ENABLE; + + ret_val = e1000_write_kmrn_reg_locked(hw, E1000_KMRNCTRLSTA_K1_CONFIG, + kmrn_reg); + if (ret_val) + return ret_val; + + usec_delay(20); + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + ctrl_reg = E1000_READ_REG(hw, E1000_CTRL); + + reg = ctrl_reg & ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100); + reg |= E1000_CTRL_FRCSPD; + E1000_WRITE_REG(hw, E1000_CTRL, reg); + + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_SPD_BYPS); + E1000_WRITE_FLUSH(hw); + usec_delay(20); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl_reg); + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); + usec_delay(20); + + return E1000_SUCCESS; +} + +/** + * e1000_oem_bits_config_ich8lan - SW-based LCD Configuration + * @hw: pointer to the HW structure + * @d0_state: boolean if entering d0 or d3 device state + * + * SW will configure Gbe Disable and LPLU based on the NVM. The four bits are + * collectively called OEM bits. The OEM Write Enable bit and SW Config bit + * in NVM determines whether HW should configure LPLU and Gbe Disable. + **/ +STATIC s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state) +{ + s32 ret_val = 0; + u32 mac_reg; + u16 oem_reg; + + DEBUGFUNC("e1000_oem_bits_config_ich8lan"); + + if (hw->mac.type < e1000_pchlan) + return ret_val; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + + if (hw->mac.type == e1000_pchlan) { + mac_reg = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + if (mac_reg & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) + goto release; + } + + mac_reg = E1000_READ_REG(hw, E1000_FEXTNVM); + if (!(mac_reg & E1000_FEXTNVM_SW_CONFIG_ICH8M)) + goto release; + + mac_reg = E1000_READ_REG(hw, E1000_PHY_CTRL); + + ret_val = hw->phy.ops.read_reg_locked(hw, HV_OEM_BITS, &oem_reg); + if (ret_val) + goto release; + + oem_reg &= ~(HV_OEM_BITS_GBE_DIS | HV_OEM_BITS_LPLU); + + if (d0_state) { + if (mac_reg & E1000_PHY_CTRL_GBE_DISABLE) + oem_reg |= HV_OEM_BITS_GBE_DIS; + + if (mac_reg & E1000_PHY_CTRL_D0A_LPLU) + oem_reg |= HV_OEM_BITS_LPLU; + } else { + if (mac_reg & (E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE)) + oem_reg |= HV_OEM_BITS_GBE_DIS; + + if (mac_reg & (E1000_PHY_CTRL_D0A_LPLU | + E1000_PHY_CTRL_NOND0A_LPLU)) + oem_reg |= HV_OEM_BITS_LPLU; + } + + /* Set Restart auto-neg to activate the bits */ + if ((d0_state || (hw->mac.type != e1000_pchlan)) && + !hw->phy.ops.check_reset_block(hw)) + oem_reg |= HV_OEM_BITS_RESTART_AN; + + ret_val = hw->phy.ops.write_reg_locked(hw, HV_OEM_BITS, oem_reg); + +release: + hw->phy.ops.release(hw); + + return ret_val; +} + + +/** + * e1000_set_mdio_slow_mode_hv - Set slow MDIO access mode + * @hw: pointer to the HW structure + **/ +STATIC s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw) +{ + s32 ret_val; + u16 data; + + DEBUGFUNC("e1000_set_mdio_slow_mode_hv"); + + ret_val = hw->phy.ops.read_reg(hw, HV_KMRN_MODE_CTRL, &data); + if (ret_val) + return ret_val; + + data |= HV_KMRN_MDIO_SLOW; + + ret_val = hw->phy.ops.write_reg(hw, HV_KMRN_MODE_CTRL, data); + + return ret_val; +} + +/** + * e1000_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be + * done after every PHY reset. + **/ +STATIC s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 phy_data; + + DEBUGFUNC("e1000_hv_phy_workarounds_ich8lan"); + + if (hw->mac.type != e1000_pchlan) + return E1000_SUCCESS; + + /* Set MDIO slow mode before any other MDIO access */ + if (hw->phy.type == e1000_phy_82577) { + ret_val = e1000_set_mdio_slow_mode_hv(hw); + if (ret_val) + return ret_val; + } + + if (((hw->phy.type == e1000_phy_82577) && + ((hw->phy.revision == 1) || (hw->phy.revision == 2))) || + ((hw->phy.type == e1000_phy_82578) && (hw->phy.revision == 1))) { + /* Disable generation of early preamble */ + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(769, 25), 0x4431); + if (ret_val) + return ret_val; + + /* Preamble tuning for SSC */ + ret_val = hw->phy.ops.write_reg(hw, HV_KMRN_FIFO_CTRLSTA, + 0xA204); + if (ret_val) + return ret_val; + } + + if (hw->phy.type == e1000_phy_82578) { + /* Return registers to default by doing a soft reset then + * writing 0x3140 to the control register. + */ + if (hw->phy.revision < 2) { + e1000_phy_sw_reset_generic(hw); + ret_val = hw->phy.ops.write_reg(hw, PHY_CONTROL, + 0x3140); + } + } + + /* Select page 0 */ + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + + hw->phy.addr = 1; + ret_val = e1000_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0); + hw->phy.ops.release(hw); + if (ret_val) + return ret_val; + + /* Configure the K1 Si workaround during phy reset assuming there is + * link so that it disables K1 if link is in 1Gbps. + */ + ret_val = e1000_k1_gig_workaround_hv(hw, true); + if (ret_val) + return ret_val; + + /* Workaround for link disconnects on a busy hub in half duplex */ + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + ret_val = hw->phy.ops.read_reg_locked(hw, BM_PORT_GEN_CFG, &phy_data); + if (ret_val) + goto release; + ret_val = hw->phy.ops.write_reg_locked(hw, BM_PORT_GEN_CFG, + phy_data & 0x00FF); + if (ret_val) + goto release; + + /* set MSE higher to enable link to stay up when noise is high */ + ret_val = e1000_write_emi_reg_locked(hw, I82577_MSE_THRESHOLD, 0x0034); +release: + hw->phy.ops.release(hw); + + return ret_val; +} + +/** + * e1000_copy_rx_addrs_to_phy_ich8lan - Copy Rx addresses from MAC to PHY + * @hw: pointer to the HW structure + **/ +void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw) +{ + u32 mac_reg; + u16 i, phy_reg = 0; + s32 ret_val; + + DEBUGFUNC("e1000_copy_rx_addrs_to_phy_ich8lan"); + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return; + ret_val = e1000_enable_phy_wakeup_reg_access_bm(hw, &phy_reg); + if (ret_val) + goto release; + + /* Copy both RAL/H (rar_entry_count) and SHRAL/H to PHY */ + for (i = 0; i < (hw->mac.rar_entry_count); i++) { + mac_reg = E1000_READ_REG(hw, E1000_RAL(i)); + hw->phy.ops.write_reg_page(hw, BM_RAR_L(i), + (u16)(mac_reg & 0xFFFF)); + hw->phy.ops.write_reg_page(hw, BM_RAR_M(i), + (u16)((mac_reg >> 16) & 0xFFFF)); + + mac_reg = E1000_READ_REG(hw, E1000_RAH(i)); + hw->phy.ops.write_reg_page(hw, BM_RAR_H(i), + (u16)(mac_reg & 0xFFFF)); + hw->phy.ops.write_reg_page(hw, BM_RAR_CTRL(i), + (u16)((mac_reg & E1000_RAH_AV) + >> 16)); + } + + e1000_disable_phy_wakeup_reg_access_bm(hw, &phy_reg); + +release: + hw->phy.ops.release(hw); +} + +#ifndef CRC32_OS_SUPPORT +STATIC u32 e1000_calc_rx_da_crc(u8 mac[]) +{ + u32 poly = 0xEDB88320; /* Polynomial for 802.3 CRC calculation */ + u32 i, j, mask, crc; + + DEBUGFUNC("e1000_calc_rx_da_crc"); + + crc = 0xffffffff; + for (i = 0; i < 6; i++) { + crc = crc ^ mac[i]; + for (j = 8; j > 0; j--) { + mask = (crc & 1) * (-1); + crc = (crc >> 1) ^ (poly & mask); + } + } + return ~crc; +} + +#endif /* CRC32_OS_SUPPORT */ +/** + * e1000_lv_jumbo_workaround_ich8lan - required for jumbo frame operation + * with 82579 PHY + * @hw: pointer to the HW structure + * @enable: flag to enable/disable workaround when enabling/disabling jumbos + **/ +s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable) +{ + s32 ret_val = E1000_SUCCESS; + u16 phy_reg, data; + u32 mac_reg; + u16 i; + + DEBUGFUNC("e1000_lv_jumbo_workaround_ich8lan"); + + if (hw->mac.type < e1000_pch2lan) + return E1000_SUCCESS; + + /* disable Rx path while enabling/disabling workaround */ + hw->phy.ops.read_reg(hw, PHY_REG(769, 20), &phy_reg); + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(769, 20), + phy_reg | (1 << 14)); + if (ret_val) + return ret_val; + + if (enable) { + /* Write Rx addresses (rar_entry_count for RAL/H, and + * SHRAL/H) and initial CRC values to the MAC + */ + for (i = 0; i < hw->mac.rar_entry_count; i++) { + u8 mac_addr[ETH_ADDR_LEN] = {0}; + u32 addr_high, addr_low; + + addr_high = E1000_READ_REG(hw, E1000_RAH(i)); + if (!(addr_high & E1000_RAH_AV)) + continue; + addr_low = E1000_READ_REG(hw, E1000_RAL(i)); + mac_addr[0] = (addr_low & 0xFF); + mac_addr[1] = ((addr_low >> 8) & 0xFF); + mac_addr[2] = ((addr_low >> 16) & 0xFF); + mac_addr[3] = ((addr_low >> 24) & 0xFF); + mac_addr[4] = (addr_high & 0xFF); + mac_addr[5] = ((addr_high >> 8) & 0xFF); + +#ifndef CRC32_OS_SUPPORT + E1000_WRITE_REG(hw, E1000_PCH_RAICC(i), + e1000_calc_rx_da_crc(mac_addr)); +#else /* CRC32_OS_SUPPORT */ + E1000_WRITE_REG(hw, E1000_PCH_RAICC(i), + E1000_CRC32(ETH_ADDR_LEN, mac_addr)); +#endif /* CRC32_OS_SUPPORT */ + } + + /* Write Rx addresses to the PHY */ + e1000_copy_rx_addrs_to_phy_ich8lan(hw); + + /* Enable jumbo frame workaround in the MAC */ + mac_reg = E1000_READ_REG(hw, E1000_FFLT_DBG); + mac_reg &= ~(1 << 14); + mac_reg |= (7 << 15); + E1000_WRITE_REG(hw, E1000_FFLT_DBG, mac_reg); + + mac_reg = E1000_READ_REG(hw, E1000_RCTL); + mac_reg |= E1000_RCTL_SECRC; + E1000_WRITE_REG(hw, E1000_RCTL, mac_reg); + + ret_val = e1000_read_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_CTRL_OFFSET, + &data); + if (ret_val) + return ret_val; + ret_val = e1000_write_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_CTRL_OFFSET, + data | (1 << 0)); + if (ret_val) + return ret_val; + ret_val = e1000_read_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_HD_CTRL, + &data); + if (ret_val) + return ret_val; + data &= ~(0xF << 8); + data |= (0xB << 8); + ret_val = e1000_write_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_HD_CTRL, + data); + if (ret_val) + return ret_val; + + /* Enable jumbo frame workaround in the PHY */ + hw->phy.ops.read_reg(hw, PHY_REG(769, 23), &data); + data &= ~(0x7F << 5); + data |= (0x37 << 5); + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(769, 23), data); + if (ret_val) + return ret_val; + hw->phy.ops.read_reg(hw, PHY_REG(769, 16), &data); + data &= ~(1 << 13); + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(769, 16), data); + if (ret_val) + return ret_val; + hw->phy.ops.read_reg(hw, PHY_REG(776, 20), &data); + data &= ~(0x3FF << 2); + data |= (E1000_TX_PTR_GAP << 2); + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(776, 20), data); + if (ret_val) + return ret_val; + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(776, 23), 0xF100); + if (ret_val) + return ret_val; + hw->phy.ops.read_reg(hw, HV_PM_CTRL, &data); + ret_val = hw->phy.ops.write_reg(hw, HV_PM_CTRL, data | + (1 << 10)); + if (ret_val) + return ret_val; + } else { + /* Write MAC register values back to h/w defaults */ + mac_reg = E1000_READ_REG(hw, E1000_FFLT_DBG); + mac_reg &= ~(0xF << 14); + E1000_WRITE_REG(hw, E1000_FFLT_DBG, mac_reg); + + mac_reg = E1000_READ_REG(hw, E1000_RCTL); + mac_reg &= ~E1000_RCTL_SECRC; + E1000_WRITE_REG(hw, E1000_RCTL, mac_reg); + + ret_val = e1000_read_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_CTRL_OFFSET, + &data); + if (ret_val) + return ret_val; + ret_val = e1000_write_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_CTRL_OFFSET, + data & ~(1 << 0)); + if (ret_val) + return ret_val; + ret_val = e1000_read_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_HD_CTRL, + &data); + if (ret_val) + return ret_val; + data &= ~(0xF << 8); + data |= (0xB << 8); + ret_val = e1000_write_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_HD_CTRL, + data); + if (ret_val) + return ret_val; + + /* Write PHY register values back to h/w defaults */ + hw->phy.ops.read_reg(hw, PHY_REG(769, 23), &data); + data &= ~(0x7F << 5); + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(769, 23), data); + if (ret_val) + return ret_val; + hw->phy.ops.read_reg(hw, PHY_REG(769, 16), &data); + data |= (1 << 13); + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(769, 16), data); + if (ret_val) + return ret_val; + hw->phy.ops.read_reg(hw, PHY_REG(776, 20), &data); + data &= ~(0x3FF << 2); + data |= (0x8 << 2); + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(776, 20), data); + if (ret_val) + return ret_val; + ret_val = hw->phy.ops.write_reg(hw, PHY_REG(776, 23), 0x7E00); + if (ret_val) + return ret_val; + hw->phy.ops.read_reg(hw, HV_PM_CTRL, &data); + ret_val = hw->phy.ops.write_reg(hw, HV_PM_CTRL, data & + ~(1 << 10)); + if (ret_val) + return ret_val; + } + + /* re-enable Rx path after enabling/disabling workaround */ + return hw->phy.ops.write_reg(hw, PHY_REG(769, 20), phy_reg & + ~(1 << 14)); +} + +/** + * e1000_lv_phy_workarounds_ich8lan - A series of Phy workarounds to be + * done after every PHY reset. + **/ +STATIC s32 e1000_lv_phy_workarounds_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_lv_phy_workarounds_ich8lan"); + + if (hw->mac.type != e1000_pch2lan) + return E1000_SUCCESS; + + /* Set MDIO slow mode before any other MDIO access */ + ret_val = e1000_set_mdio_slow_mode_hv(hw); + if (ret_val) + return ret_val; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + /* set MSE higher to enable link to stay up when noise is high */ + ret_val = e1000_write_emi_reg_locked(hw, I82579_MSE_THRESHOLD, 0x0034); + if (ret_val) + goto release; + /* drop link after 5 times MSE threshold was reached */ + ret_val = e1000_write_emi_reg_locked(hw, I82579_MSE_LINK_DOWN, 0x0005); +release: + hw->phy.ops.release(hw); + + return ret_val; +} + +/** + * e1000_k1_gig_workaround_lv - K1 Si workaround + * @hw: pointer to the HW structure + * + * Workaround to set the K1 beacon duration for 82579 parts in 10Mbps + * Disable K1 for 1000 and 100 speeds + **/ +STATIC s32 e1000_k1_workaround_lv(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 status_reg = 0; + + DEBUGFUNC("e1000_k1_workaround_lv"); + + if (hw->mac.type != e1000_pch2lan) + return E1000_SUCCESS; + + /* Set K1 beacon duration based on 10Mbs speed */ + ret_val = hw->phy.ops.read_reg(hw, HV_M_STATUS, &status_reg); + if (ret_val) + return ret_val; + + if ((status_reg & (HV_M_STATUS_LINK_UP | HV_M_STATUS_AUTONEG_COMPLETE)) + == (HV_M_STATUS_LINK_UP | HV_M_STATUS_AUTONEG_COMPLETE)) { + if (status_reg & + (HV_M_STATUS_SPEED_1000 | HV_M_STATUS_SPEED_100)) { + u16 pm_phy_reg; + + /* LV 1G/100 Packet drop issue wa */ + ret_val = hw->phy.ops.read_reg(hw, HV_PM_CTRL, + &pm_phy_reg); + if (ret_val) + return ret_val; + pm_phy_reg &= ~HV_PM_CTRL_K1_ENABLE; + ret_val = hw->phy.ops.write_reg(hw, HV_PM_CTRL, + pm_phy_reg); + if (ret_val) + return ret_val; + } else { + u32 mac_reg; + mac_reg = E1000_READ_REG(hw, E1000_FEXTNVM4); + mac_reg &= ~E1000_FEXTNVM4_BEACON_DURATION_MASK; + mac_reg |= E1000_FEXTNVM4_BEACON_DURATION_16USEC; + E1000_WRITE_REG(hw, E1000_FEXTNVM4, mac_reg); + } + } + + return ret_val; +} + +/** + * e1000_gate_hw_phy_config_ich8lan - disable PHY config via hardware + * @hw: pointer to the HW structure + * @gate: boolean set to true to gate, false to ungate + * + * Gate/ungate the automatic PHY configuration via hardware; perform + * the configuration via software instead. + **/ +STATIC void e1000_gate_hw_phy_config_ich8lan(struct e1000_hw *hw, bool gate) +{ + u32 extcnf_ctrl; + + DEBUGFUNC("e1000_gate_hw_phy_config_ich8lan"); + + if (hw->mac.type < e1000_pch2lan) + return; + + extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + + if (gate) + extcnf_ctrl |= E1000_EXTCNF_CTRL_GATE_PHY_CFG; + else + extcnf_ctrl &= ~E1000_EXTCNF_CTRL_GATE_PHY_CFG; + + E1000_WRITE_REG(hw, E1000_EXTCNF_CTRL, extcnf_ctrl); +} + +/** + * e1000_lan_init_done_ich8lan - Check for PHY config completion + * @hw: pointer to the HW structure + * + * Check the appropriate indication the MAC has finished configuring the + * PHY after a software reset. + **/ +STATIC void e1000_lan_init_done_ich8lan(struct e1000_hw *hw) +{ + u32 data, loop = E1000_ICH8_LAN_INIT_TIMEOUT; + + DEBUGFUNC("e1000_lan_init_done_ich8lan"); + + /* Wait for basic configuration completes before proceeding */ + do { + data = E1000_READ_REG(hw, E1000_STATUS); + data &= E1000_STATUS_LAN_INIT_DONE; + usec_delay(100); + } while ((!data) && --loop); + + /* If basic configuration is incomplete before the above loop + * count reaches 0, loading the configuration from NVM will + * leave the PHY in a bad state possibly resulting in no link. + */ + if (loop == 0) + DEBUGOUT("LAN_INIT_DONE not set, increase timeout\n"); + + /* Clear the Init Done bit for the next init event */ + data = E1000_READ_REG(hw, E1000_STATUS); + data &= ~E1000_STATUS_LAN_INIT_DONE; + E1000_WRITE_REG(hw, E1000_STATUS, data); +} + +/** + * e1000_post_phy_reset_ich8lan - Perform steps required after a PHY reset + * @hw: pointer to the HW structure + **/ +STATIC s32 e1000_post_phy_reset_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 reg; + + DEBUGFUNC("e1000_post_phy_reset_ich8lan"); + + if (hw->phy.ops.check_reset_block(hw)) + return E1000_SUCCESS; + + /* Allow time for h/w to get to quiescent state after reset */ + msec_delay(10); + + /* Perform any necessary post-reset workarounds */ + switch (hw->mac.type) { + case e1000_pchlan: + ret_val = e1000_hv_phy_workarounds_ich8lan(hw); + if (ret_val) + return ret_val; + break; + case e1000_pch2lan: + ret_val = e1000_lv_phy_workarounds_ich8lan(hw); + if (ret_val) + return ret_val; + break; + default: + break; + } + + /* Clear the host wakeup bit after lcd reset */ + if (hw->mac.type >= e1000_pchlan) { + hw->phy.ops.read_reg(hw, BM_PORT_GEN_CFG, ®); + reg &= ~BM_WUC_HOST_WU_BIT; + hw->phy.ops.write_reg(hw, BM_PORT_GEN_CFG, reg); + } + + /* Configure the LCD with the extended configuration region in NVM */ + ret_val = e1000_sw_lcd_config_ich8lan(hw); + if (ret_val) + return ret_val; + + /* Configure the LCD with the OEM bits in NVM */ + ret_val = e1000_oem_bits_config_ich8lan(hw, true); + + if (hw->mac.type == e1000_pch2lan) { + /* Ungate automatic PHY configuration on non-managed 82579 */ + if (!(E1000_READ_REG(hw, E1000_FWSM) & + E1000_ICH_FWSM_FW_VALID)) { + msec_delay(10); + e1000_gate_hw_phy_config_ich8lan(hw, false); + } + + /* Set EEE LPI Update Timer to 200usec */ + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + ret_val = e1000_write_emi_reg_locked(hw, + I82579_LPI_UPDATE_TIMER, + 0x1387); + hw->phy.ops.release(hw); + } + + return ret_val; +} + +/** + * e1000_phy_hw_reset_ich8lan - Performs a PHY reset + * @hw: pointer to the HW structure + * + * Resets the PHY + * This is a function pointer entry point called by drivers + * or other shared routines. + **/ +STATIC s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_phy_hw_reset_ich8lan"); + + /* Gate automatic PHY configuration by hardware on non-managed 82579 */ + if ((hw->mac.type == e1000_pch2lan) && + !(E1000_READ_REG(hw, E1000_FWSM) & E1000_ICH_FWSM_FW_VALID)) + e1000_gate_hw_phy_config_ich8lan(hw, true); + + ret_val = e1000_phy_hw_reset_generic(hw); + if (ret_val) + return ret_val; + + return e1000_post_phy_reset_ich8lan(hw); +} + +/** + * e1000_set_lplu_state_pchlan - Set Low Power Link Up state + * @hw: pointer to the HW structure + * @active: true to enable LPLU, false to disable + * + * Sets the LPLU state according to the active flag. For PCH, if OEM write + * bit are disabled in the NVM, writing the LPLU bits in the MAC will not set + * the phy speed. This function will manually set the LPLU bit and restart + * auto-neg as hw would do. D3 and D0 LPLU will call the same function + * since it configures the same bit. + **/ +STATIC s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active) +{ + s32 ret_val; + u16 oem_reg; + + DEBUGFUNC("e1000_set_lplu_state_pchlan"); + ret_val = hw->phy.ops.read_reg(hw, HV_OEM_BITS, &oem_reg); + if (ret_val) + return ret_val; + + if (active) + oem_reg |= HV_OEM_BITS_LPLU; + else + oem_reg &= ~HV_OEM_BITS_LPLU; + + if (!hw->phy.ops.check_reset_block(hw)) + oem_reg |= HV_OEM_BITS_RESTART_AN; + + return hw->phy.ops.write_reg(hw, HV_OEM_BITS, oem_reg); +} + +/** + * e1000_set_d0_lplu_state_ich8lan - Set Low Power Linkup D0 state + * @hw: pointer to the HW structure + * @active: true to enable LPLU, false to disable + * + * Sets the LPLU D0 state according to the active flag. When + * activating LPLU this function also disables smart speed + * and vice versa. LPLU will not be activated unless the + * device autonegotiation advertisement meets standards of + * either 10 or 10/100 or 10/100/1000 at all duplexes. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +STATIC s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 phy_ctrl; + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_set_d0_lplu_state_ich8lan"); + + if (phy->type == e1000_phy_ife) + return E1000_SUCCESS; + + phy_ctrl = E1000_READ_REG(hw, E1000_PHY_CTRL); + + if (active) { + phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + if (phy->type != e1000_phy_igp_3) + return E1000_SUCCESS; + + /* Call gig speed drop workaround on LPLU before accessing + * any PHY registers + */ + if (hw->mac.type == e1000_ich8lan) + e1000_gig_downshift_workaround_ich8lan(hw); + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + return ret_val; + } else { + phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + if (phy->type != e1000_phy_igp_3) + return E1000_SUCCESS; + + /* LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + return ret_val; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + return ret_val; + } + } + + return E1000_SUCCESS; +} + +/** + * e1000_set_d3_lplu_state_ich8lan - Set Low Power Linkup D3 state + * @hw: pointer to the HW structure + * @active: true to enable LPLU, false to disable + * + * Sets the LPLU D3 state according to the active flag. When + * activating LPLU this function also disables smart speed + * and vice versa. LPLU will not be activated unless the + * device autonegotiation advertisement meets standards of + * either 10 or 10/100 or 10/100/1000 at all duplexes. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +STATIC s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 phy_ctrl; + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_set_d3_lplu_state_ich8lan"); + + phy_ctrl = E1000_READ_REG(hw, E1000_PHY_CTRL); + + if (!active) { + phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + if (phy->type != e1000_phy_igp_3) + return E1000_SUCCESS; + + /* LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + return ret_val; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + return ret_val; + } + } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || + (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || + (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { + phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + if (phy->type != e1000_phy_igp_3) + return E1000_SUCCESS; + + /* Call gig speed drop workaround on LPLU before accessing + * any PHY registers + */ + if (hw->mac.type == e1000_ich8lan) + e1000_gig_downshift_workaround_ich8lan(hw); + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + } + + return ret_val; +} + +/** + * e1000_valid_nvm_bank_detect_ich8lan - finds out the valid bank 0 or 1 + * @hw: pointer to the HW structure + * @bank: pointer to the variable that returns the active bank + * + * Reads signature byte from the NVM using the flash access registers. + * Word 0x13 bits 15:14 = 10b indicate a valid signature for that bank. + **/ +STATIC s32 e1000_valid_nvm_bank_detect_ich8lan(struct e1000_hw *hw, u32 *bank) +{ + u32 eecd; + struct e1000_nvm_info *nvm = &hw->nvm; + u32 bank1_offset = nvm->flash_bank_size * sizeof(u16); + u32 act_offset = E1000_ICH_NVM_SIG_WORD * 2 + 1; + u32 nvm_dword = 0; + u8 sig_byte = 0; + s32 ret_val; + + DEBUGFUNC("e1000_valid_nvm_bank_detect_ich8lan"); + + switch (hw->mac.type) { + case e1000_ich8lan: + case e1000_ich9lan: + eecd = E1000_READ_REG(hw, E1000_EECD); + if ((eecd & E1000_EECD_SEC1VAL_VALID_MASK) == + E1000_EECD_SEC1VAL_VALID_MASK) { + if (eecd & E1000_EECD_SEC1VAL) + *bank = 1; + else + *bank = 0; + + return E1000_SUCCESS; + } + DEBUGOUT("Unable to determine valid NVM bank via EEC - reading flash signature\n"); + /* fall-thru */ + default: + /* set bank to 0 in case flash read fails */ + *bank = 0; + + /* Check bank 0 */ + ret_val = e1000_read_flash_byte_ich8lan(hw, act_offset, + &sig_byte); + if (ret_val) + return ret_val; + if ((sig_byte & E1000_ICH_NVM_VALID_SIG_MASK) == + E1000_ICH_NVM_SIG_VALUE) { + *bank = 0; + return E1000_SUCCESS; + } + + /* Check bank 1 */ + ret_val = e1000_read_flash_byte_ich8lan(hw, act_offset + + bank1_offset, + &sig_byte); + if (ret_val) + return ret_val; + if ((sig_byte & E1000_ICH_NVM_VALID_SIG_MASK) == + E1000_ICH_NVM_SIG_VALUE) { + *bank = 1; + return E1000_SUCCESS; + } + + DEBUGOUT("ERROR: No valid NVM bank present\n"); + return -E1000_ERR_NVM; + } +} + +/** + * e1000_read_nvm_ich8lan - Read word(s) from the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the word(s) to read. + * @words: Size of data to read in words + * @data: Pointer to the word(s) to read at offset. + * + * Reads a word(s) from the NVM using the flash access registers. + **/ +STATIC s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 act_offset; + s32 ret_val = E1000_SUCCESS; + u32 bank = 0; + u16 i, word; + + DEBUGFUNC("e1000_read_nvm_ich8lan"); + + if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + nvm->ops.acquire(hw); + + ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); + if (ret_val != E1000_SUCCESS) { + DEBUGOUT("Could not detect valid bank, assuming bank 0\n"); + bank = 0; + } + + act_offset = (bank) ? nvm->flash_bank_size : 0; + act_offset += offset; + + ret_val = E1000_SUCCESS; + for (i = 0; i < words; i++) { + if (dev_spec->shadow_ram[offset+i].modified) { + data[i] = dev_spec->shadow_ram[offset+i].value; + } else { + ret_val = e1000_read_flash_word_ich8lan(hw, + act_offset + i, + &word); + if (ret_val) + break; + data[i] = word; + } + } + + nvm->ops.release(hw); + +out: + if (ret_val) + DEBUGOUT1("NVM read error: %d\n", ret_val); + + return ret_val; +} + +/** + * e1000_flash_cycle_init_ich8lan - Initialize flash + * @hw: pointer to the HW structure + * + * This function does initial flash setup so that a new read/write/erase cycle + * can be started. + **/ +STATIC s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw) +{ + union ich8_hws_flash_status hsfsts; + s32 ret_val = -E1000_ERR_NVM; + + DEBUGFUNC("e1000_flash_cycle_init_ich8lan"); + + hsfsts.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + + /* Check if the flash descriptor is valid */ + if (!hsfsts.hsf_status.fldesvalid) { + DEBUGOUT("Flash descriptor invalid. SW Sequencing must be used.\n"); + return -E1000_ERR_NVM; + } + + /* Clear FCERR and DAEL in hw status by writing 1 */ + hsfsts.hsf_status.flcerr = 1; + hsfsts.hsf_status.dael = 1; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); + + /* Either we should have a hardware SPI cycle in progress + * bit to check against, in order to start a new cycle or + * FDONE bit should be changed in the hardware so that it + * is 1 after hardware reset, which can then be used as an + * indication whether a cycle is in progress or has been + * completed. + */ + + if (!hsfsts.hsf_status.flcinprog) { + /* There is no cycle running at present, + * so we can start a cycle. + * Begin by setting Flash Cycle Done. + */ + hsfsts.hsf_status.flcdone = 1; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); + ret_val = E1000_SUCCESS; + } else { + s32 i; + + /* Otherwise poll for sometime so the current + * cycle has a chance to end before giving up. + */ + for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++) { + hsfsts.regval = E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFSTS); + if (!hsfsts.hsf_status.flcinprog) { + ret_val = E1000_SUCCESS; + break; + } + usec_delay(1); + } + if (ret_val == E1000_SUCCESS) { + /* Successful in waiting for previous cycle to timeout, + * now set the Flash Cycle Done. + */ + hsfsts.hsf_status.flcdone = 1; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, + hsfsts.regval); + } else { + DEBUGOUT("Flash controller busy, cannot get access\n"); + } + } + + return ret_val; +} + +/** + * e1000_flash_cycle_ich8lan - Starts flash cycle (read/write/erase) + * @hw: pointer to the HW structure + * @timeout: maximum time to wait for completion + * + * This function starts a flash cycle and waits for its completion. + **/ +STATIC s32 e1000_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout) +{ + union ich8_hws_flash_ctrl hsflctl; + union ich8_hws_flash_status hsfsts; + u32 i = 0; + + DEBUGFUNC("e1000_flash_cycle_ich8lan"); + + /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ + hsflctl.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + hsflctl.hsf_ctrl.flcgo = 1; + + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + + /* wait till FDONE bit is set to 1 */ + do { + hsfsts.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcdone) + break; + usec_delay(1); + } while (i++ < timeout); + + if (hsfsts.hsf_status.flcdone && !hsfsts.hsf_status.flcerr) + return E1000_SUCCESS; + + return -E1000_ERR_NVM; +} + +/** + * e1000_read_flash_word_ich8lan - Read word from flash + * @hw: pointer to the HW structure + * @offset: offset to data location + * @data: pointer to the location for storing the data + * + * Reads the flash word at offset into data. Offset is converted + * to bytes before read. + **/ +STATIC s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset, + u16 *data) +{ + DEBUGFUNC("e1000_read_flash_word_ich8lan"); + + if (!data) + return -E1000_ERR_NVM; + + /* Must convert offset into bytes. */ + offset <<= 1; + + return e1000_read_flash_data_ich8lan(hw, offset, 2, data); +} + +/** + * e1000_read_flash_byte_ich8lan - Read byte from flash + * @hw: pointer to the HW structure + * @offset: The offset of the byte to read. + * @data: Pointer to a byte to store the value read. + * + * Reads a single byte from the NVM using the flash access registers. + **/ +STATIC s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset, + u8 *data) +{ + s32 ret_val; + u16 word = 0; + + ret_val = e1000_read_flash_data_ich8lan(hw, offset, 1, &word); + + if (ret_val) + return ret_val; + + *data = (u8)word; + + return E1000_SUCCESS; +} + +/** + * e1000_read_flash_data_ich8lan - Read byte or word from NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the byte or word to read. + * @size: Size of data to read, 1=byte 2=word + * @data: Pointer to the word to store the value read. + * + * Reads a byte or word from the NVM using the flash access registers. + **/ +STATIC s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 *data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + u32 flash_data = 0; + s32 ret_val = -E1000_ERR_NVM; + u8 count = 0; + + DEBUGFUNC("e1000_read_flash_data_ich8lan"); + + if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK) + return -E1000_ERR_NVM; + flash_linear_addr = ((ICH_FLASH_LINEAR_ADDR_MASK & offset) + + hw->nvm.flash_base_addr); + + do { + usec_delay(1); + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val != E1000_SUCCESS) + break; + hsflctl.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size - 1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_addr); + + ret_val = e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_READ_COMMAND_TIMEOUT); + + /* Check if FCERR is set to 1, if set to 1, clear it + * and try the whole sequence a few more times, else + * read in (shift in) the Flash Data0, the order is + * least significant byte first msb to lsb + */ + if (ret_val == E1000_SUCCESS) { + flash_data = E1000_READ_FLASH_REG(hw, ICH_FLASH_FDATA0); + if (size == 1) + *data = (u8)(flash_data & 0x000000FF); + else if (size == 2) + *data = (u16)(flash_data & 0x0000FFFF); + break; + } else { + /* If we've gotten here, then things are probably + * completely hosed, but if the error condition is + * detected, it won't hurt to give it another try... + * ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr) { + /* Repeat for some time before giving up. */ + continue; + } else if (!hsfsts.hsf_status.flcdone) { + DEBUGOUT("Timeout error - flash cycle did not complete.\n"); + break; + } + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + + return ret_val; +} + + +/** + * e1000_write_nvm_ich8lan - Write word(s) to the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the word(s) to write. + * @words: Size of data to write in words + * @data: Pointer to the word(s) to write at offset. + * + * Writes a byte or word to the NVM using the flash access registers. + **/ +STATIC s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u16 i; + + DEBUGFUNC("e1000_write_nvm_ich8lan"); + + if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + return -E1000_ERR_NVM; + } + + nvm->ops.acquire(hw); + + for (i = 0; i < words; i++) { + dev_spec->shadow_ram[offset+i].modified = true; + dev_spec->shadow_ram[offset+i].value = data[i]; + } + + nvm->ops.release(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM + * @hw: pointer to the HW structure + * + * The NVM checksum is updated by calling the generic update_nvm_checksum, + * which writes the checksum to the shadow ram. The changes in the shadow + * ram are then committed to the EEPROM by processing each bank at a time + * checking for the modified bit and writing only the pending changes. + * After a successful commit, the shadow ram is cleared and is ready for + * future writes. + **/ +STATIC s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 i, act_offset, new_bank_offset, old_bank_offset, bank; + s32 ret_val; + u16 data = 0; + + DEBUGFUNC("e1000_update_nvm_checksum_ich8lan"); + + ret_val = e1000_update_nvm_checksum_generic(hw); + if (ret_val) + goto out; + + if (nvm->type != e1000_nvm_flash_sw) + goto out; + + nvm->ops.acquire(hw); + + /* We're writing to the opposite bank so if we're on bank 1, + * write to bank 0 etc. We also need to erase the segment that + * is going to be written + */ + ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); + if (ret_val != E1000_SUCCESS) { + DEBUGOUT("Could not detect valid bank, assuming bank 0\n"); + bank = 0; + } + + if (bank == 0) { + new_bank_offset = nvm->flash_bank_size; + old_bank_offset = 0; + ret_val = e1000_erase_flash_bank_ich8lan(hw, 1); + if (ret_val) + goto release; + } else { + old_bank_offset = nvm->flash_bank_size; + new_bank_offset = 0; + ret_val = e1000_erase_flash_bank_ich8lan(hw, 0); + if (ret_val) + goto release; + } + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + if (dev_spec->shadow_ram[i].modified) { + data = dev_spec->shadow_ram[i].value; + } else { + ret_val = e1000_read_flash_word_ich8lan(hw, i + + old_bank_offset, + &data); + if (ret_val) + break; + } + /* If the word is 0x13, then make sure the signature bits + * (15:14) are 11b until the commit has completed. + * This will allow us to write 10b which indicates the + * signature is valid. We want to do this after the write + * has completed so that we don't mark the segment valid + * while the write is still in progress + */ + if (i == E1000_ICH_NVM_SIG_WORD) + data |= E1000_ICH_NVM_SIG_MASK; + + /* Convert offset to bytes. */ + act_offset = (i + new_bank_offset) << 1; + + usec_delay(100); + + /* Write the bytes to the new bank. */ + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, + act_offset, + (u8)data); + if (ret_val) + break; + + usec_delay(100); + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, + act_offset + 1, + (u8)(data >> 8)); + if (ret_val) + break; + } + + /* Don't bother writing the segment valid bits if sector + * programming failed. + */ + if (ret_val) { + DEBUGOUT("Flash commit failed.\n"); + goto release; + } + + /* Finally validate the new segment by setting bit 15:14 + * to 10b in word 0x13 , this can be done without an + * erase as well since these bits are 11 to start with + * and we need to change bit 14 to 0b + */ + act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD; + ret_val = e1000_read_flash_word_ich8lan(hw, act_offset, &data); + if (ret_val) + goto release; + + data &= 0xBFFF; + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, act_offset * 2 + 1, + (u8)(data >> 8)); + if (ret_val) + goto release; + + /* And invalidate the previously valid segment by setting + * its signature word (0x13) high_byte to 0b. This can be + * done without an erase because flash erase sets all bits + * to 1's. We can write 1's to 0's without an erase + */ + act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1; + + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, act_offset, 0); + + if (ret_val) + goto release; + + /* Great! Everything worked, we can now clear the cached entries. */ + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + dev_spec->shadow_ram[i].modified = false; + dev_spec->shadow_ram[i].value = 0xFFFF; + } + +release: + nvm->ops.release(hw); + + /* Reload the EEPROM, or else modifications will not appear + * until after the next adapter reset. + */ + if (!ret_val) { + nvm->ops.reload(hw); + msec_delay(10); + } + +out: + if (ret_val) + DEBUGOUT1("NVM update error: %d\n", ret_val); + + return ret_val; +} + +/** + * e1000_validate_nvm_checksum_ich8lan - Validate EEPROM checksum + * @hw: pointer to the HW structure + * + * Check to see if checksum needs to be fixed by reading bit 6 in word 0x19. + * If the bit is 0, that the EEPROM had been modified, but the checksum was not + * calculated, in which case we need to calculate the checksum and set bit 6. + **/ +STATIC s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val; + u16 data; + u16 word; + u16 valid_csum_mask; + + DEBUGFUNC("e1000_validate_nvm_checksum_ich8lan"); + + /* Read NVM and check Invalid Image CSUM bit. If this bit is 0, + * the checksum needs to be fixed. This bit is an indication that + * the NVM was prepared by OEM software and did not calculate + * the checksum...a likely scenario. + */ + switch (hw->mac.type) { + case e1000_pch_lpt: + word = NVM_COMPAT; + valid_csum_mask = NVM_COMPAT_VALID_CSUM; + break; + default: + word = NVM_FUTURE_INIT_WORD1; + valid_csum_mask = NVM_FUTURE_INIT_WORD1_VALID_CSUM; + break; + } + + ret_val = hw->nvm.ops.read(hw, word, 1, &data); + if (ret_val) + return ret_val; + + if (!(data & valid_csum_mask)) { + data |= valid_csum_mask; + ret_val = hw->nvm.ops.write(hw, word, 1, &data); + if (ret_val) + return ret_val; + ret_val = hw->nvm.ops.update(hw); + if (ret_val) + return ret_val; + } + + return e1000_validate_nvm_checksum_generic(hw); +} + +/** + * e1000_write_flash_data_ich8lan - Writes bytes to the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the byte/word to read. + * @size: Size of data to read, 1=byte 2=word + * @data: The byte(s) to write to the NVM. + * + * Writes one/two bytes to the NVM using the flash access registers. + **/ +STATIC s32 e1000_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + u32 flash_data = 0; + s32 ret_val; + u8 count = 0; + + DEBUGFUNC("e1000_write_ich8_data"); + + if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK) + return -E1000_ERR_NVM; + + flash_linear_addr = ((ICH_FLASH_LINEAR_ADDR_MASK & offset) + + hw->nvm.flash_base_addr); + + do { + usec_delay(1); + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val != E1000_SUCCESS) + break; + hsflctl.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size - 1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_addr); + + if (size == 1) + flash_data = (u32)data & 0x00FF; + else + flash_data = (u32)data; + + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FDATA0, flash_data); + + /* check if FCERR is set to 1 , if set to 1, clear it + * and try the whole sequence a few more times else done + */ + ret_val = + e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_WRITE_COMMAND_TIMEOUT); + if (ret_val == E1000_SUCCESS) + break; + + /* If we're here, then things are most likely + * completely hosed, but if the error condition + * is detected, it won't hurt to give it another + * try...ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr) + /* Repeat for some time before giving up. */ + continue; + if (!hsfsts.hsf_status.flcdone) { + DEBUGOUT("Timeout error - flash cycle did not complete.\n"); + break; + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + + return ret_val; +} + + +/** + * e1000_write_flash_byte_ich8lan - Write a single byte to NVM + * @hw: pointer to the HW structure + * @offset: The index of the byte to read. + * @data: The byte to write to the NVM. + * + * Writes a single byte to the NVM using the flash access registers. + **/ +STATIC s32 e1000_write_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset, + u8 data) +{ + u16 word = (u16)data; + + DEBUGFUNC("e1000_write_flash_byte_ich8lan"); + + return e1000_write_flash_data_ich8lan(hw, offset, 1, word); +} + + + +/** + * e1000_retry_write_flash_byte_ich8lan - Writes a single byte to NVM + * @hw: pointer to the HW structure + * @offset: The offset of the byte to write. + * @byte: The byte to write to the NVM. + * + * Writes a single byte to the NVM using the flash access registers. + * Goes through a retry algorithm before giving up. + **/ +STATIC s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, + u32 offset, u8 byte) +{ + s32 ret_val; + u16 program_retries; + + DEBUGFUNC("e1000_retry_write_flash_byte_ich8lan"); + + ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); + if (!ret_val) + return ret_val; + + for (program_retries = 0; program_retries < 100; program_retries++) { + DEBUGOUT2("Retrying Byte %2.2X at offset %u\n", byte, offset); + usec_delay(100); + ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); + if (ret_val == E1000_SUCCESS) + break; + } + if (program_retries == 100) + return -E1000_ERR_NVM; + + return E1000_SUCCESS; +} + +/** + * e1000_erase_flash_bank_ich8lan - Erase a bank (4k) from NVM + * @hw: pointer to the HW structure + * @bank: 0 for first bank, 1 for second bank, etc. + * + * Erases the bank specified. Each bank is a 4k block. Banks are 0 based. + * bank N is 4096 * N + flash_reg_addr. + **/ +STATIC s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + /* bank size is in 16bit words - adjust to bytes */ + u32 flash_bank_size = nvm->flash_bank_size * 2; + s32 ret_val; + s32 count = 0; + s32 j, iteration, sector_size; + + DEBUGFUNC("e1000_erase_flash_bank_ich8lan"); + + hsfsts.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + + /* Determine HW Sector size: Read BERASE bits of hw flash status + * register + * 00: The Hw sector is 256 bytes, hence we need to erase 16 + * consecutive sectors. The start index for the nth Hw sector + * can be calculated as = bank * 4096 + n * 256 + * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector. + * The start index for the nth Hw sector can be calculated + * as = bank * 4096 + * 10: The Hw sector is 8K bytes, nth sector = bank * 8192 + * (ich9 only, otherwise error condition) + * 11: The Hw sector is 64K bytes, nth sector = bank * 65536 + */ + switch (hsfsts.hsf_status.berasesz) { + case 0: + /* Hw sector size 256 */ + sector_size = ICH_FLASH_SEG_SIZE_256; + iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_256; + break; + case 1: + sector_size = ICH_FLASH_SEG_SIZE_4K; + iteration = 1; + break; + case 2: + sector_size = ICH_FLASH_SEG_SIZE_8K; + iteration = 1; + break; + case 3: + sector_size = ICH_FLASH_SEG_SIZE_64K; + iteration = 1; + break; + default: + return -E1000_ERR_NVM; + } + + /* Start with the base address, then add the sector offset. */ + flash_linear_addr = hw->nvm.flash_base_addr; + flash_linear_addr += (bank) ? flash_bank_size : 0; + + for (j = 0; j < iteration; j++) { + do { + u32 timeout = ICH_FLASH_ERASE_COMMAND_TIMEOUT; + + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val) + return ret_val; + + /* Write a value 11 (block Erase) in Flash + * Cycle field in hw flash control + */ + hsflctl.regval = + E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, + hsflctl.regval); + + /* Write the last 24 bits of an index within the + * block into Flash Linear address field in Flash + * Address. + */ + flash_linear_addr += (j * sector_size); + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FADDR, + flash_linear_addr); + + ret_val = e1000_flash_cycle_ich8lan(hw, timeout); + if (ret_val == E1000_SUCCESS) + break; + + /* Check if FCERR is set to 1. If 1, + * clear it and try the whole sequence + * a few more times else Done + */ + hsfsts.regval = E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr) + /* repeat for some time before giving up */ + continue; + else if (!hsfsts.hsf_status.flcdone) + return ret_val; + } while (++count < ICH_FLASH_CYCLE_REPEAT_COUNT); + } + + return E1000_SUCCESS; +} + +/** + * e1000_valid_led_default_ich8lan - Set the default LED settings + * @hw: pointer to the HW structure + * @data: Pointer to the LED settings + * + * Reads the LED default settings from the NVM to data. If the NVM LED + * settings is all 0's or F's, set the LED default to a valid LED default + * setting. + **/ +STATIC s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data) +{ + s32 ret_val; + + DEBUGFUNC("e1000_valid_led_default_ich8lan"); + + ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + return ret_val; + } + + if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) + *data = ID_LED_DEFAULT_ICH8LAN; + + return E1000_SUCCESS; +} + +/** + * e1000_id_led_init_pchlan - store LED configurations + * @hw: pointer to the HW structure + * + * PCH does not control LEDs via the LEDCTL register, rather it uses + * the PHY LED configuration register. + * + * PCH also does not have an "always on" or "always off" mode which + * complicates the ID feature. Instead of using the "on" mode to indicate + * in ledctl_mode2 the LEDs to use for ID (see e1000_id_led_init_generic()), + * use "link_up" mode. The LEDs will still ID on request if there is no + * link based on logic in e1000_led_[on|off]_pchlan(). + **/ +STATIC s32 e1000_id_led_init_pchlan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val; + const u32 ledctl_on = E1000_LEDCTL_MODE_LINK_UP; + const u32 ledctl_off = E1000_LEDCTL_MODE_LINK_UP | E1000_PHY_LED0_IVRT; + u16 data, i, temp, shift; + + DEBUGFUNC("e1000_id_led_init_pchlan"); + + /* Get default ID LED modes */ + ret_val = hw->nvm.ops.valid_led_default(hw, &data); + if (ret_val) + return ret_val; + + mac->ledctl_default = E1000_READ_REG(hw, E1000_LEDCTL); + mac->ledctl_mode1 = mac->ledctl_default; + mac->ledctl_mode2 = mac->ledctl_default; + + for (i = 0; i < 4; i++) { + temp = (data >> (i << 2)) & E1000_LEDCTL_LED0_MODE_MASK; + shift = (i * 5); + switch (temp) { + case ID_LED_ON1_DEF2: + case ID_LED_ON1_ON2: + case ID_LED_ON1_OFF2: + mac->ledctl_mode1 &= ~(E1000_PHY_LED0_MASK << shift); + mac->ledctl_mode1 |= (ledctl_on << shift); + break; + case ID_LED_OFF1_DEF2: + case ID_LED_OFF1_ON2: + case ID_LED_OFF1_OFF2: + mac->ledctl_mode1 &= ~(E1000_PHY_LED0_MASK << shift); + mac->ledctl_mode1 |= (ledctl_off << shift); + break; + default: + /* Do nothing */ + break; + } + switch (temp) { + case ID_LED_DEF1_ON2: + case ID_LED_ON1_ON2: + case ID_LED_OFF1_ON2: + mac->ledctl_mode2 &= ~(E1000_PHY_LED0_MASK << shift); + mac->ledctl_mode2 |= (ledctl_on << shift); + break; + case ID_LED_DEF1_OFF2: + case ID_LED_ON1_OFF2: + case ID_LED_OFF1_OFF2: + mac->ledctl_mode2 &= ~(E1000_PHY_LED0_MASK << shift); + mac->ledctl_mode2 |= (ledctl_off << shift); + break; + default: + /* Do nothing */ + break; + } + } + + return E1000_SUCCESS; +} + +/** + * e1000_get_bus_info_ich8lan - Get/Set the bus type and width + * @hw: pointer to the HW structure + * + * ICH8 use the PCI Express bus, but does not contain a PCI Express Capability + * register, so the the bus width is hard coded. + **/ +STATIC s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw) +{ + struct e1000_bus_info *bus = &hw->bus; + s32 ret_val; + + DEBUGFUNC("e1000_get_bus_info_ich8lan"); + + ret_val = e1000_get_bus_info_pcie_generic(hw); + + /* ICH devices are "PCI Express"-ish. They have + * a configuration space, but do not contain + * PCI Express Capability registers, so bus width + * must be hardcoded. + */ + if (bus->width == e1000_bus_width_unknown) + bus->width = e1000_bus_width_pcie_x1; + + return ret_val; +} + +/** + * e1000_reset_hw_ich8lan - Reset the hardware + * @hw: pointer to the HW structure + * + * Does a full reset of the hardware which includes a reset of the PHY and + * MAC. + **/ +STATIC s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) +{ + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u16 kum_cfg; + u32 ctrl, reg; + s32 ret_val; + + DEBUGFUNC("e1000_reset_hw_ich8lan"); + + /* Prevent the PCI-E bus from sticking if there is no TLP connection + * on the last TLP read/write transaction when MAC is reset. + */ + ret_val = e1000_disable_pcie_master_generic(hw); + if (ret_val) + DEBUGOUT("PCI-E Master disable polling has failed.\n"); + + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + + /* Disable the Transmit and Receive units. Then delay to allow + * any pending transactions to complete before we hit the MAC + * with the global reset. + */ + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + msec_delay(10); + + /* Workaround for ICH8 bit corruption issue in FIFO memory */ + if (hw->mac.type == e1000_ich8lan) { + /* Set Tx and Rx buffer allocation to 8k apiece. */ + E1000_WRITE_REG(hw, E1000_PBA, E1000_PBA_8K); + /* Set Packet Buffer Size to 16k. */ + E1000_WRITE_REG(hw, E1000_PBS, E1000_PBS_16K); + } + + if (hw->mac.type == e1000_pchlan) { + /* Save the NVM K1 bit setting*/ + ret_val = e1000_read_nvm(hw, E1000_NVM_K1_CONFIG, 1, &kum_cfg); + if (ret_val) + return ret_val; + + if (kum_cfg & E1000_NVM_K1_ENABLE) + dev_spec->nvm_k1_enabled = true; + else + dev_spec->nvm_k1_enabled = false; + } + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + if (!hw->phy.ops.check_reset_block(hw)) { + /* Full-chip reset requires MAC and PHY reset at the same + * time to make sure the interface between MAC and the + * external PHY is reset. + */ + ctrl |= E1000_CTRL_PHY_RST; + + /* Gate automatic PHY configuration by hardware on + * non-managed 82579 + */ + if ((hw->mac.type == e1000_pch2lan) && + !(E1000_READ_REG(hw, E1000_FWSM) & E1000_ICH_FWSM_FW_VALID)) + e1000_gate_hw_phy_config_ich8lan(hw, true); + } + ret_val = e1000_acquire_swflag_ich8lan(hw); + DEBUGOUT("Issuing a global reset to ich8lan\n"); + E1000_WRITE_REG(hw, E1000_CTRL, (ctrl | E1000_CTRL_RST)); + /* cannot issue a flush here because it hangs the hardware */ + msec_delay(20); + + /* Set Phy Config Counter to 50msec */ + if (hw->mac.type == e1000_pch2lan) { + reg = E1000_READ_REG(hw, E1000_FEXTNVM3); + reg &= ~E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK; + reg |= E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC; + E1000_WRITE_REG(hw, E1000_FEXTNVM3, reg); + } + + if (!ret_val) + E1000_MUTEX_UNLOCK(&hw->dev_spec.ich8lan.swflag_mutex); + + if (ctrl & E1000_CTRL_PHY_RST) { + ret_val = hw->phy.ops.get_cfg_done(hw); + if (ret_val) + return ret_val; + + ret_val = e1000_post_phy_reset_ich8lan(hw); + if (ret_val) + return ret_val; + } + + /* For PCH, this write will make sure that any noise + * will be detected as a CRC error and be dropped rather than show up + * as a bad packet to the DMA engine. + */ + if (hw->mac.type == e1000_pchlan) + E1000_WRITE_REG(hw, E1000_CRC_OFFSET, 0x65656565); + + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + E1000_READ_REG(hw, E1000_ICR); + + reg = E1000_READ_REG(hw, E1000_KABGTXD); + reg |= E1000_KABGTXD_BGSQLBIAS; + E1000_WRITE_REG(hw, E1000_KABGTXD, reg); + + return E1000_SUCCESS; +} + +/** + * e1000_init_hw_ich8lan - Initialize the hardware + * @hw: pointer to the HW structure + * + * Prepares the hardware for transmit and receive by doing the following: + * - initialize hardware bits + * - initialize LED identification + * - setup receive address registers + * - setup flow control + * - setup transmit descriptors + * - clear statistics + **/ +STATIC s32 e1000_init_hw_ich8lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 ctrl_ext, txdctl, snoop; + s32 ret_val; + u16 i; + + DEBUGFUNC("e1000_init_hw_ich8lan"); + + e1000_initialize_hw_bits_ich8lan(hw); + + /* Initialize identification LED */ + ret_val = mac->ops.id_led_init(hw); + /* An error is not fatal and we should not stop init due to this */ + if (ret_val) + DEBUGOUT("Error initializing identification LED\n"); + + /* Setup the receive address. */ + e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + + /* The 82578 Rx buffer will stall if wakeup is enabled in host and + * the ME. Disable wakeup by clearing the host wakeup bit. + * Reset the phy after disabling host wakeup to reset the Rx buffer. + */ + if (hw->phy.type == e1000_phy_82578) { + hw->phy.ops.read_reg(hw, BM_PORT_GEN_CFG, &i); + i &= ~BM_WUC_HOST_WU_BIT; + hw->phy.ops.write_reg(hw, BM_PORT_GEN_CFG, i); + ret_val = e1000_phy_hw_reset_ich8lan(hw); + if (ret_val) + return ret_val; + } + + /* Setup link and flow control */ + ret_val = mac->ops.setup_link(hw); + + /* Set the transmit descriptor write-back policy for both queues */ + txdctl = E1000_READ_REG(hw, E1000_TXDCTL(0)); + txdctl = ((txdctl & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB); + txdctl = ((txdctl & ~E1000_TXDCTL_PTHRESH) | + E1000_TXDCTL_MAX_TX_DESC_PREFETCH); + E1000_WRITE_REG(hw, E1000_TXDCTL(0), txdctl); + txdctl = E1000_READ_REG(hw, E1000_TXDCTL(1)); + txdctl = ((txdctl & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB); + txdctl = ((txdctl & ~E1000_TXDCTL_PTHRESH) | + E1000_TXDCTL_MAX_TX_DESC_PREFETCH); + E1000_WRITE_REG(hw, E1000_TXDCTL(1), txdctl); + + /* ICH8 has opposite polarity of no_snoop bits. + * By default, we should use snoop behavior. + */ + if (mac->type == e1000_ich8lan) + snoop = PCIE_ICH8_SNOOP_ALL; + else + snoop = (u32) ~(PCIE_NO_SNOOP_ALL); + e1000_set_pcie_no_snoop_generic(hw, snoop); + + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_RO_DIS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + + /* Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_ich8lan(hw); + + return ret_val; +} + +/** + * e1000_initialize_hw_bits_ich8lan - Initialize required hardware bits + * @hw: pointer to the HW structure + * + * Sets/Clears required hardware bits necessary for correctly setting up the + * hardware for transmit and receive. + **/ +STATIC void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw) +{ + u32 reg; + + DEBUGFUNC("e1000_initialize_hw_bits_ich8lan"); + + /* Extended Device Control */ + reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + reg |= (1 << 22); + /* Enable PHY low-power state when MAC is at D3 w/o WoL */ + if (hw->mac.type >= e1000_pchlan) + reg |= E1000_CTRL_EXT_PHYPDEN; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, reg); + + /* Transmit Descriptor Control 0 */ + reg = E1000_READ_REG(hw, E1000_TXDCTL(0)); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg); + + /* Transmit Descriptor Control 1 */ + reg = E1000_READ_REG(hw, E1000_TXDCTL(1)); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg); + + /* Transmit Arbitration Control 0 */ + reg = E1000_READ_REG(hw, E1000_TARC(0)); + if (hw->mac.type == e1000_ich8lan) + reg |= (1 << 28) | (1 << 29); + reg |= (1 << 23) | (1 << 24) | (1 << 26) | (1 << 27); + E1000_WRITE_REG(hw, E1000_TARC(0), reg); + + /* Transmit Arbitration Control 1 */ + reg = E1000_READ_REG(hw, E1000_TARC(1)); + if (E1000_READ_REG(hw, E1000_TCTL) & E1000_TCTL_MULR) + reg &= ~(1 << 28); + else + reg |= (1 << 28); + reg |= (1 << 24) | (1 << 26) | (1 << 30); + E1000_WRITE_REG(hw, E1000_TARC(1), reg); + + /* Device Status */ + if (hw->mac.type == e1000_ich8lan) { + reg = E1000_READ_REG(hw, E1000_STATUS); + reg &= ~(1 << 31); + E1000_WRITE_REG(hw, E1000_STATUS, reg); + } + + /* work-around descriptor data corruption issue during nfs v2 udp + * traffic, just disable the nfs filtering capability + */ + reg = E1000_READ_REG(hw, E1000_RFCTL); + reg |= (E1000_RFCTL_NFSW_DIS | E1000_RFCTL_NFSR_DIS); + + /* Disable IPv6 extension header parsing because some malformed + * IPv6 headers can hang the Rx. + */ + if (hw->mac.type == e1000_ich8lan) + reg |= (E1000_RFCTL_IPV6_EX_DIS | E1000_RFCTL_NEW_IPV6_EXT_DIS); + E1000_WRITE_REG(hw, E1000_RFCTL, reg); + + /* Enable ECC on Lynxpoint */ + if (hw->mac.type == e1000_pch_lpt) { + reg = E1000_READ_REG(hw, E1000_PBECCSTS); + reg |= E1000_PBECCSTS_ECC_ENABLE; + E1000_WRITE_REG(hw, E1000_PBECCSTS, reg); + + reg = E1000_READ_REG(hw, E1000_CTRL); + reg |= E1000_CTRL_MEHE; + E1000_WRITE_REG(hw, E1000_CTRL, reg); + } + + return; +} + +/** + * e1000_setup_link_ich8lan - Setup flow control and link settings + * @hw: pointer to the HW structure + * + * Determines which flow control settings to use, then configures flow + * control. Calls the appropriate media-specific link configuration + * function. Assuming the adapter has a valid link partner, a valid link + * should be established. Assumes the hardware has previously been reset + * and the transmitter and receiver are not enabled. + **/ +STATIC s32 e1000_setup_link_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val; + + DEBUGFUNC("e1000_setup_link_ich8lan"); + + if (hw->phy.ops.check_reset_block(hw)) + return E1000_SUCCESS; + + /* ICH parts do not have a word in the NVM to determine + * the default flow control setting, so we explicitly + * set it to full. + */ + if (hw->fc.requested_mode == e1000_fc_default) + hw->fc.requested_mode = e1000_fc_full; + + /* Save off the requested flow control mode for use later. Depending + * on the link partner's capabilities, we may or may not use this mode. + */ + hw->fc.current_mode = hw->fc.requested_mode; + + DEBUGOUT1("After fix-ups FlowControl is now = %x\n", + hw->fc.current_mode); + + /* Continue to configure the copper link. */ + ret_val = hw->mac.ops.setup_physical_interface(hw); + if (ret_val) + return ret_val; + + E1000_WRITE_REG(hw, E1000_FCTTV, hw->fc.pause_time); + if ((hw->phy.type == e1000_phy_82578) || + (hw->phy.type == e1000_phy_82579) || + (hw->phy.type == e1000_phy_i217) || + (hw->phy.type == e1000_phy_82577)) { + E1000_WRITE_REG(hw, E1000_FCRTV_PCH, hw->fc.refresh_time); + + ret_val = hw->phy.ops.write_reg(hw, + PHY_REG(BM_PORT_CTRL_PAGE, 27), + hw->fc.pause_time); + if (ret_val) + return ret_val; + } + + return e1000_set_fc_watermarks_generic(hw); +} + +/** + * e1000_setup_copper_link_ich8lan - Configure MAC/PHY interface + * @hw: pointer to the HW structure + * + * Configures the kumeran interface to the PHY to wait the appropriate time + * when polling the PHY, then call the generic setup_copper_link to finish + * configuring the copper link. + **/ +STATIC s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val; + u16 reg_data; + + DEBUGFUNC("e1000_setup_copper_link_ich8lan"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + /* Set the mac to wait the maximum time between each iteration + * and increase the max iterations when polling the phy; + * this fixes erroneous timeouts at 10Mbps. + */ + ret_val = e1000_write_kmrn_reg_generic(hw, E1000_KMRNCTRLSTA_TIMEOUTS, + 0xFFFF); + if (ret_val) + return ret_val; + ret_val = e1000_read_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_INBAND_PARAM, + ®_data); + if (ret_val) + return ret_val; + reg_data |= 0x3F; + ret_val = e1000_write_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_INBAND_PARAM, + reg_data); + if (ret_val) + return ret_val; + + switch (hw->phy.type) { + case e1000_phy_igp_3: + ret_val = e1000_copper_link_setup_igp(hw); + if (ret_val) + return ret_val; + break; + case e1000_phy_bm: + case e1000_phy_82578: + ret_val = e1000_copper_link_setup_m88(hw); + if (ret_val) + return ret_val; + break; + case e1000_phy_82577: + case e1000_phy_82579: + ret_val = e1000_copper_link_setup_82577(hw); + if (ret_val) + return ret_val; + break; + case e1000_phy_ife: + ret_val = hw->phy.ops.read_reg(hw, IFE_PHY_MDIX_CONTROL, + ®_data); + if (ret_val) + return ret_val; + + reg_data &= ~IFE_PMC_AUTO_MDIX; + + switch (hw->phy.mdix) { + case 1: + reg_data &= ~IFE_PMC_FORCE_MDIX; + break; + case 2: + reg_data |= IFE_PMC_FORCE_MDIX; + break; + case 0: + default: + reg_data |= IFE_PMC_AUTO_MDIX; + break; + } + ret_val = hw->phy.ops.write_reg(hw, IFE_PHY_MDIX_CONTROL, + reg_data); + if (ret_val) + return ret_val; + break; + default: + break; + } + + return e1000_setup_copper_link_generic(hw); +} + +/** + * e1000_setup_copper_link_pch_lpt - Configure MAC/PHY interface + * @hw: pointer to the HW structure + * + * Calls the PHY specific link setup function and then calls the + * generic setup_copper_link to finish configuring the link for + * Lynxpoint PCH devices + **/ +STATIC s32 e1000_setup_copper_link_pch_lpt(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val; + + DEBUGFUNC("e1000_setup_copper_link_pch_lpt"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + ret_val = e1000_copper_link_setup_82577(hw); + if (ret_val) + return ret_val; + + return e1000_setup_copper_link_generic(hw); +} + +/** + * e1000_get_link_up_info_ich8lan - Get current link speed and duplex + * @hw: pointer to the HW structure + * @speed: pointer to store current link speed + * @duplex: pointer to store the current link duplex + * + * Calls the generic get_speed_and_duplex to retrieve the current link + * information and then calls the Kumeran lock loss workaround for links at + * gigabit speeds. + **/ +STATIC s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed, + u16 *duplex) +{ + s32 ret_val; + + DEBUGFUNC("e1000_get_link_up_info_ich8lan"); + + ret_val = e1000_get_speed_and_duplex_copper_generic(hw, speed, duplex); + if (ret_val) + return ret_val; + + if ((hw->mac.type == e1000_ich8lan) && + (hw->phy.type == e1000_phy_igp_3) && + (*speed == SPEED_1000)) { + ret_val = e1000_kmrn_lock_loss_workaround_ich8lan(hw); + } + + return ret_val; +} + +/** + * e1000_kmrn_lock_loss_workaround_ich8lan - Kumeran workaround + * @hw: pointer to the HW structure + * + * Work-around for 82566 Kumeran PCS lock loss: + * On link status change (i.e. PCI reset, speed change) and link is up and + * speed is gigabit- + * 0) if workaround is optionally disabled do nothing + * 1) wait 1ms for Kumeran link to come up + * 2) check Kumeran Diagnostic register PCS lock loss bit + * 3) if not set the link is locked (all is good), otherwise... + * 4) reset the PHY + * 5) repeat up to 10 times + * Note: this is only called for IGP3 copper when speed is 1gb. + **/ +STATIC s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw) +{ + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 phy_ctrl; + s32 ret_val; + u16 i, data; + bool link; + + DEBUGFUNC("e1000_kmrn_lock_loss_workaround_ich8lan"); + + if (!dev_spec->kmrn_lock_loss_workaround_enabled) + return E1000_SUCCESS; + + /* Make sure link is up before proceeding. If not just return. + * Attempting this while link is negotiating fouled up link + * stability + */ + ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); + if (!link) + return E1000_SUCCESS; + + for (i = 0; i < 10; i++) { + /* read once to clear */ + ret_val = hw->phy.ops.read_reg(hw, IGP3_KMRN_DIAG, &data); + if (ret_val) + return ret_val; + /* and again to get new status */ + ret_val = hw->phy.ops.read_reg(hw, IGP3_KMRN_DIAG, &data); + if (ret_val) + return ret_val; + + /* check for PCS lock */ + if (!(data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) + return E1000_SUCCESS; + + /* Issue PHY reset */ + hw->phy.ops.reset(hw); + msec_delay_irq(5); + } + /* Disable GigE link negotiation */ + phy_ctrl = E1000_READ_REG(hw, E1000_PHY_CTRL); + phy_ctrl |= (E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + /* Call gig speed drop workaround on Gig disable before accessing + * any PHY registers + */ + e1000_gig_downshift_workaround_ich8lan(hw); + + /* unable to acquire PCS lock */ + return -E1000_ERR_PHY; +} + +/** + * e1000_set_kmrn_lock_loss_workaround_ich8lan - Set Kumeran workaround state + * @hw: pointer to the HW structure + * @state: boolean value used to set the current Kumeran workaround state + * + * If ICH8, set the current Kumeran workaround state (enabled - true + * /disabled - false). + **/ +void e1000_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw, + bool state) +{ + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + + DEBUGFUNC("e1000_set_kmrn_lock_loss_workaround_ich8lan"); + + if (hw->mac.type != e1000_ich8lan) { + DEBUGOUT("Workaround applies to ICH8 only.\n"); + return; + } + + dev_spec->kmrn_lock_loss_workaround_enabled = state; + + return; +} + +/** + * e1000_ipg3_phy_powerdown_workaround_ich8lan - Power down workaround on D3 + * @hw: pointer to the HW structure + * + * Workaround for 82566 power-down on D3 entry: + * 1) disable gigabit link + * 2) write VR power-down enable + * 3) read it back + * Continue if successful, else issue LCD reset and repeat + **/ +void e1000_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw) +{ + u32 reg; + u16 data; + u8 retry = 0; + + DEBUGFUNC("e1000_igp3_phy_powerdown_workaround_ich8lan"); + + if (hw->phy.type != e1000_phy_igp_3) + return; + + /* Try the workaround twice (if needed) */ + do { + /* Disable link */ + reg = E1000_READ_REG(hw, E1000_PHY_CTRL); + reg |= (E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + E1000_WRITE_REG(hw, E1000_PHY_CTRL, reg); + + /* Call gig speed drop workaround on Gig disable before + * accessing any PHY registers + */ + if (hw->mac.type == e1000_ich8lan) + e1000_gig_downshift_workaround_ich8lan(hw); + + /* Write VR power-down enable */ + hw->phy.ops.read_reg(hw, IGP3_VR_CTRL, &data); + data &= ~IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; + hw->phy.ops.write_reg(hw, IGP3_VR_CTRL, + data | IGP3_VR_CTRL_MODE_SHUTDOWN); + + /* Read it back and test */ + hw->phy.ops.read_reg(hw, IGP3_VR_CTRL, &data); + data &= IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; + if ((data == IGP3_VR_CTRL_MODE_SHUTDOWN) || retry) + break; + + /* Issue PHY reset and repeat at most one more time */ + reg = E1000_READ_REG(hw, E1000_CTRL); + E1000_WRITE_REG(hw, E1000_CTRL, reg | E1000_CTRL_PHY_RST); + retry++; + } while (retry); +} + +/** + * e1000_gig_downshift_workaround_ich8lan - WoL from S5 stops working + * @hw: pointer to the HW structure + * + * Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC), + * LPLU, Gig disable, MDIC PHY reset): + * 1) Set Kumeran Near-end loopback + * 2) Clear Kumeran Near-end loopback + * Should only be called for ICH8[m] devices with any 1G Phy. + **/ +void e1000_gig_downshift_workaround_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val; + u16 reg_data; + + DEBUGFUNC("e1000_gig_downshift_workaround_ich8lan"); + + if ((hw->mac.type != e1000_ich8lan) || + (hw->phy.type == e1000_phy_ife)) + return; + + ret_val = e1000_read_kmrn_reg_generic(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, + ®_data); + if (ret_val) + return; + reg_data |= E1000_KMRNCTRLSTA_DIAG_NELPBK; + ret_val = e1000_write_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_DIAG_OFFSET, + reg_data); + if (ret_val) + return; + reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK; + e1000_write_kmrn_reg_generic(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, + reg_data); +} + +/** + * e1000_suspend_workarounds_ich8lan - workarounds needed during S0->Sx + * @hw: pointer to the HW structure + * + * During S0 to Sx transition, it is possible the link remains at gig + * instead of negotiating to a lower speed. Before going to Sx, set + * 'Gig Disable' to force link speed negotiation to a lower speed based on + * the LPLU setting in the NVM or custom setting. For PCH and newer parts, + * the OEM bits PHY register (LED, GbE disable and LPLU configurations) also + * needs to be written. + * Parts that support (and are linked to a partner which support) EEE in + * 100Mbps should disable LPLU since 100Mbps w/ EEE requires less power + * than 10Mbps w/o EEE. + **/ +void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw) +{ + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 phy_ctrl; + s32 ret_val; + + DEBUGFUNC("e1000_suspend_workarounds_ich8lan"); + + phy_ctrl = E1000_READ_REG(hw, E1000_PHY_CTRL); + phy_ctrl |= E1000_PHY_CTRL_GBE_DISABLE; + + if (hw->phy.type == e1000_phy_i217) { + u16 phy_reg, device_id = hw->device_id; + + if ((device_id == E1000_DEV_ID_PCH_LPTLP_I218_LM) || + (device_id == E1000_DEV_ID_PCH_LPTLP_I218_V) || + (device_id == E1000_DEV_ID_PCH_I218_LM3) || + (device_id == E1000_DEV_ID_PCH_I218_V3)) { + u32 fextnvm6 = E1000_READ_REG(hw, E1000_FEXTNVM6); + + E1000_WRITE_REG(hw, E1000_FEXTNVM6, + fextnvm6 & ~E1000_FEXTNVM6_REQ_PLL_CLK); + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + if (!dev_spec->eee_disable) { + u16 eee_advert; + + ret_val = + e1000_read_emi_reg_locked(hw, + I217_EEE_ADVERTISEMENT, + &eee_advert); + if (ret_val) + goto release; + + /* Disable LPLU if both link partners support 100BaseT + * EEE and 100Full is advertised on both ends of the + * link, and enable Auto Enable LPI since there will + * be no driver to enable LPI while in Sx. + */ + if ((eee_advert & I82579_EEE_100_SUPPORTED) && + (dev_spec->eee_lp_ability & + I82579_EEE_100_SUPPORTED) && + (hw->phy.autoneg_advertised & ADVERTISE_100_FULL)) { + phy_ctrl &= ~(E1000_PHY_CTRL_D0A_LPLU | + E1000_PHY_CTRL_NOND0A_LPLU); + + /* Set Auto Enable LPI after link up */ + hw->phy.ops.read_reg_locked(hw, + I217_LPI_GPIO_CTRL, + &phy_reg); + phy_reg |= I217_LPI_GPIO_CTRL_AUTO_EN_LPI; + hw->phy.ops.write_reg_locked(hw, + I217_LPI_GPIO_CTRL, + phy_reg); + } + } + + /* For i217 Intel Rapid Start Technology support, + * when the system is going into Sx and no manageability engine + * is present, the driver must configure proxy to reset only on + * power good. LPI (Low Power Idle) state must also reset only + * on power good, as well as the MTA (Multicast table array). + * The SMBus release must also be disabled on LCD reset. + */ + if (!(E1000_READ_REG(hw, E1000_FWSM) & + E1000_ICH_FWSM_FW_VALID)) { + /* Enable proxy to reset only on power good. */ + hw->phy.ops.read_reg_locked(hw, I217_PROXY_CTRL, + &phy_reg); + phy_reg |= I217_PROXY_CTRL_AUTO_DISABLE; + hw->phy.ops.write_reg_locked(hw, I217_PROXY_CTRL, + phy_reg); + + /* Set bit enable LPI (EEE) to reset only on + * power good. + */ + hw->phy.ops.read_reg_locked(hw, I217_SxCTRL, &phy_reg); + phy_reg |= I217_SxCTRL_ENABLE_LPI_RESET; + hw->phy.ops.write_reg_locked(hw, I217_SxCTRL, phy_reg); + + /* Disable the SMB release on LCD reset. */ + hw->phy.ops.read_reg_locked(hw, I217_MEMPWR, &phy_reg); + phy_reg &= ~I217_MEMPWR_DISABLE_SMB_RELEASE; + hw->phy.ops.write_reg_locked(hw, I217_MEMPWR, phy_reg); + } + + /* Enable MTA to reset for Intel Rapid Start Technology + * Support + */ + hw->phy.ops.read_reg_locked(hw, I217_CGFREG, &phy_reg); + phy_reg |= I217_CGFREG_ENABLE_MTA_RESET; + hw->phy.ops.write_reg_locked(hw, I217_CGFREG, phy_reg); + +release: + hw->phy.ops.release(hw); + } +out: + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + if (hw->mac.type == e1000_ich8lan) + e1000_gig_downshift_workaround_ich8lan(hw); + + if (hw->mac.type >= e1000_pchlan) { + e1000_oem_bits_config_ich8lan(hw, false); + + /* Reset PHY to activate OEM bits on 82577/8 */ + if (hw->mac.type == e1000_pchlan) + e1000_phy_hw_reset_generic(hw); + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return; + e1000_write_smbus_addr(hw); + hw->phy.ops.release(hw); + } + + return; +} + +/** + * e1000_resume_workarounds_pchlan - workarounds needed during Sx->S0 + * @hw: pointer to the HW structure + * + * During Sx to S0 transitions on non-managed devices or managed devices + * on which PHY resets are not blocked, if the PHY registers cannot be + * accessed properly by the s/w toggle the LANPHYPC value to power cycle + * the PHY. + * On i217, setup Intel Rapid Start Technology. + **/ +u32 e1000_resume_workarounds_pchlan(struct e1000_hw *hw) +{ + s32 ret_val; + + DEBUGFUNC("e1000_resume_workarounds_pchlan"); + if (hw->mac.type < e1000_pch2lan) + return E1000_SUCCESS; + + ret_val = e1000_init_phy_workarounds_pchlan(hw); + if (ret_val) { + DEBUGOUT1("Failed to init PHY flow ret_val=%d\n", ret_val); + return ret_val; + } + + /* For i217 Intel Rapid Start Technology support when the system + * is transitioning from Sx and no manageability engine is present + * configure SMBus to restore on reset, disable proxy, and enable + * the reset on MTA (Multicast table array). + */ + if (hw->phy.type == e1000_phy_i217) { + u16 phy_reg; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) { + DEBUGOUT("Failed to setup iRST\n"); + return ret_val; + } + + /* Clear Auto Enable LPI after link up */ + hw->phy.ops.read_reg_locked(hw, I217_LPI_GPIO_CTRL, &phy_reg); + phy_reg &= ~I217_LPI_GPIO_CTRL_AUTO_EN_LPI; + hw->phy.ops.write_reg_locked(hw, I217_LPI_GPIO_CTRL, phy_reg); + + if (!(E1000_READ_REG(hw, E1000_FWSM) & + E1000_ICH_FWSM_FW_VALID)) { + /* Restore clear on SMB if no manageability engine + * is present + */ + ret_val = hw->phy.ops.read_reg_locked(hw, I217_MEMPWR, + &phy_reg); + if (ret_val) + goto release; + phy_reg |= I217_MEMPWR_DISABLE_SMB_RELEASE; + hw->phy.ops.write_reg_locked(hw, I217_MEMPWR, phy_reg); + + /* Disable Proxy */ + hw->phy.ops.write_reg_locked(hw, I217_PROXY_CTRL, 0); + } + /* Enable reset on MTA */ + ret_val = hw->phy.ops.read_reg_locked(hw, I217_CGFREG, + &phy_reg); + if (ret_val) + goto release; + phy_reg &= ~I217_CGFREG_ENABLE_MTA_RESET; + hw->phy.ops.write_reg_locked(hw, I217_CGFREG, phy_reg); +release: + if (ret_val) + DEBUGOUT1("Error %d in resume workarounds\n", ret_val); + hw->phy.ops.release(hw); + return ret_val; + } + return E1000_SUCCESS; +} + +/** + * e1000_cleanup_led_ich8lan - Restore the default LED operation + * @hw: pointer to the HW structure + * + * Return the LED back to the default configuration. + **/ +STATIC s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_cleanup_led_ich8lan"); + + if (hw->phy.type == e1000_phy_ife) + return hw->phy.ops.write_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, + 0); + + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_default); + return E1000_SUCCESS; +} + +/** + * e1000_led_on_ich8lan - Turn LEDs on + * @hw: pointer to the HW structure + * + * Turn on the LEDs. + **/ +STATIC s32 e1000_led_on_ich8lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_led_on_ich8lan"); + + if (hw->phy.type == e1000_phy_ife) + return hw->phy.ops.write_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON)); + + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_mode2); + return E1000_SUCCESS; +} + +/** + * e1000_led_off_ich8lan - Turn LEDs off + * @hw: pointer to the HW structure + * + * Turn off the LEDs. + **/ +STATIC s32 e1000_led_off_ich8lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_led_off_ich8lan"); + + if (hw->phy.type == e1000_phy_ife) + return hw->phy.ops.write_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF)); + + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_mode1); + return E1000_SUCCESS; +} + +/** + * e1000_setup_led_pchlan - Configures SW controllable LED + * @hw: pointer to the HW structure + * + * This prepares the SW controllable LED for use. + **/ +STATIC s32 e1000_setup_led_pchlan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_setup_led_pchlan"); + + return hw->phy.ops.write_reg(hw, HV_LED_CONFIG, + (u16)hw->mac.ledctl_mode1); +} + +/** + * e1000_cleanup_led_pchlan - Restore the default LED operation + * @hw: pointer to the HW structure + * + * Return the LED back to the default configuration. + **/ +STATIC s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_cleanup_led_pchlan"); + + return hw->phy.ops.write_reg(hw, HV_LED_CONFIG, + (u16)hw->mac.ledctl_default); +} + +/** + * e1000_led_on_pchlan - Turn LEDs on + * @hw: pointer to the HW structure + * + * Turn on the LEDs. + **/ +STATIC s32 e1000_led_on_pchlan(struct e1000_hw *hw) +{ + u16 data = (u16)hw->mac.ledctl_mode2; + u32 i, led; + + DEBUGFUNC("e1000_led_on_pchlan"); + + /* If no link, then turn LED on by setting the invert bit + * for each LED that's mode is "link_up" in ledctl_mode2. + */ + if (!(E1000_READ_REG(hw, E1000_STATUS) & E1000_STATUS_LU)) { + for (i = 0; i < 3; i++) { + led = (data >> (i * 5)) & E1000_PHY_LED0_MASK; + if ((led & E1000_PHY_LED0_MODE_MASK) != + E1000_LEDCTL_MODE_LINK_UP) + continue; + if (led & E1000_PHY_LED0_IVRT) + data &= ~(E1000_PHY_LED0_IVRT << (i * 5)); + else + data |= (E1000_PHY_LED0_IVRT << (i * 5)); + } + } + + return hw->phy.ops.write_reg(hw, HV_LED_CONFIG, data); +} + +/** + * e1000_led_off_pchlan - Turn LEDs off + * @hw: pointer to the HW structure + * + * Turn off the LEDs. + **/ +STATIC s32 e1000_led_off_pchlan(struct e1000_hw *hw) +{ + u16 data = (u16)hw->mac.ledctl_mode1; + u32 i, led; + + DEBUGFUNC("e1000_led_off_pchlan"); + + /* If no link, then turn LED off by clearing the invert bit + * for each LED that's mode is "link_up" in ledctl_mode1. + */ + if (!(E1000_READ_REG(hw, E1000_STATUS) & E1000_STATUS_LU)) { + for (i = 0; i < 3; i++) { + led = (data >> (i * 5)) & E1000_PHY_LED0_MASK; + if ((led & E1000_PHY_LED0_MODE_MASK) != + E1000_LEDCTL_MODE_LINK_UP) + continue; + if (led & E1000_PHY_LED0_IVRT) + data &= ~(E1000_PHY_LED0_IVRT << (i * 5)); + else + data |= (E1000_PHY_LED0_IVRT << (i * 5)); + } + } + + return hw->phy.ops.write_reg(hw, HV_LED_CONFIG, data); +} + +/** + * e1000_get_cfg_done_ich8lan - Read config done bit after Full or PHY reset + * @hw: pointer to the HW structure + * + * Read appropriate register for the config done bit for completion status + * and configure the PHY through s/w for EEPROM-less parts. + * + * NOTE: some silicon which is EEPROM-less will fail trying to read the + * config done bit, so only an error is logged and continues. If we were + * to return with error, EEPROM-less silicon would not be able to be reset + * or change link. + **/ +STATIC s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u32 bank = 0; + u32 status; + + DEBUGFUNC("e1000_get_cfg_done_ich8lan"); + + e1000_get_cfg_done_generic(hw); + + /* Wait for indication from h/w that it has completed basic config */ + if (hw->mac.type >= e1000_ich10lan) { + e1000_lan_init_done_ich8lan(hw); + } else { + ret_val = e1000_get_auto_rd_done_generic(hw); + if (ret_val) { + /* When auto config read does not complete, do not + * return with an error. This can happen in situations + * where there is no eeprom and prevents getting link. + */ + DEBUGOUT("Auto Read Done did not complete\n"); + ret_val = E1000_SUCCESS; + } + } + + /* Clear PHY Reset Asserted bit */ + status = E1000_READ_REG(hw, E1000_STATUS); + if (status & E1000_STATUS_PHYRA) + E1000_WRITE_REG(hw, E1000_STATUS, status & ~E1000_STATUS_PHYRA); + else + DEBUGOUT("PHY Reset Asserted not set - needs delay\n"); + + /* If EEPROM is not marked present, init the IGP 3 PHY manually */ + if (hw->mac.type <= e1000_ich9lan) { + if (!(E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES) && + (hw->phy.type == e1000_phy_igp_3)) { + e1000_phy_init_script_igp3(hw); + } + } else { + if (e1000_valid_nvm_bank_detect_ich8lan(hw, &bank)) { + /* Maybe we should do a basic PHY config */ + DEBUGOUT("EEPROM not present\n"); + ret_val = -E1000_ERR_CONFIG; + } + } + + return ret_val; +} + +/** + * e1000_power_down_phy_copper_ich8lan - Remove link during PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, remove the link. + **/ +STATIC void e1000_power_down_phy_copper_ich8lan(struct e1000_hw *hw) +{ + /* If the management interface is not enabled, then power down */ + if (!(hw->mac.ops.check_mng_mode(hw) || + hw->phy.ops.check_reset_block(hw))) + e1000_power_down_phy_copper(hw); + + return; +} + +/** + * e1000_clear_hw_cntrs_ich8lan - Clear statistical counters + * @hw: pointer to the HW structure + * + * Clears hardware counters specific to the silicon family and calls + * clear_hw_cntrs_generic to clear all general purpose counters. + **/ +STATIC void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw) +{ + u16 phy_data; + s32 ret_val; + + DEBUGFUNC("e1000_clear_hw_cntrs_ich8lan"); + + e1000_clear_hw_cntrs_base_generic(hw); + + E1000_READ_REG(hw, E1000_ALGNERRC); + E1000_READ_REG(hw, E1000_RXERRC); + E1000_READ_REG(hw, E1000_TNCRS); + E1000_READ_REG(hw, E1000_CEXTERR); + E1000_READ_REG(hw, E1000_TSCTC); + E1000_READ_REG(hw, E1000_TSCTFC); + + E1000_READ_REG(hw, E1000_MGTPRC); + E1000_READ_REG(hw, E1000_MGTPDC); + E1000_READ_REG(hw, E1000_MGTPTC); + + E1000_READ_REG(hw, E1000_IAC); + E1000_READ_REG(hw, E1000_ICRXOC); + + /* Clear PHY statistics registers */ + if ((hw->phy.type == e1000_phy_82578) || + (hw->phy.type == e1000_phy_82579) || + (hw->phy.type == e1000_phy_i217) || + (hw->phy.type == e1000_phy_82577)) { + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return; + ret_val = hw->phy.ops.set_page(hw, + HV_STATS_PAGE << IGP_PAGE_SHIFT); + if (ret_val) + goto release; + hw->phy.ops.read_reg_page(hw, HV_SCC_UPPER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_SCC_LOWER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_ECOL_UPPER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_ECOL_LOWER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_MCC_UPPER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_MCC_LOWER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_LATECOL_UPPER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_LATECOL_LOWER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_COLC_UPPER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_COLC_LOWER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_DC_UPPER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_DC_LOWER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_TNCRS_UPPER, &phy_data); + hw->phy.ops.read_reg_page(hw, HV_TNCRS_LOWER, &phy_data); +release: + hw->phy.ops.release(hw); + } +} + +/** + * e1000_configure_k0s_lpt - Configure K0s power state + * @hw: pointer to the HW structure + * @entry_latency: Tx idle period for entering K0s - valid values are 0 to 3. + * 0 corresponds to 128ns, each value over 0 doubles the duration. + * @min_time: Minimum Tx idle period allowed - valid values are 0 to 4. + * 0 corresponds to 128ns, each value over 0 doubles the duration. + * + * Configure the K1 power state based on the provided parameter. + * Assumes semaphore already acquired. + * + * Success returns 0, Failure returns: + * -E1000_ERR_PHY (-2) in case of access error + * -E1000_ERR_PARAM (-4) in case of parameters error + **/ +s32 e1000_configure_k0s_lpt(struct e1000_hw *hw, u8 entry_latency, u8 min_time) +{ + s32 ret_val; + u16 kmrn_reg = 0; + + DEBUGFUNC("e1000_configure_k0s_lpt"); + + if (entry_latency > 3 || min_time > 4) + return -E1000_ERR_PARAM; + + ret_val = e1000_read_kmrn_reg_locked(hw, E1000_KMRNCTRLSTA_K0S_CTRL, + &kmrn_reg); + if (ret_val) + return ret_val; + + /* for now don't touch the latency */ + kmrn_reg &= ~(E1000_KMRNCTRLSTA_K0S_CTRL_MIN_TIME_MASK); + kmrn_reg |= ((min_time << E1000_KMRNCTRLSTA_K0S_CTRL_MIN_TIME_SHIFT)); + + ret_val = e1000_write_kmrn_reg_locked(hw, E1000_KMRNCTRLSTA_K0S_CTRL, + kmrn_reg); + if (ret_val) + return ret_val; + + return E1000_SUCCESS; +} |