diff options
Diffstat (limited to 'drivers/net/ixgbe/base/ixgbe_x550.c')
| -rw-r--r-- | drivers/net/ixgbe/base/ixgbe_x550.c | 152 |
1 files changed, 49 insertions, 103 deletions
diff --git a/drivers/net/ixgbe/base/ixgbe_x550.c b/drivers/net/ixgbe/base/ixgbe_x550.c index 9862391b..f66f5407 100644 --- a/drivers/net/ixgbe/base/ixgbe_x550.c +++ b/drivers/net/ixgbe/base/ixgbe_x550.c @@ -336,98 +336,6 @@ STATIC void ixgbe_setup_mux_ctl(struct ixgbe_hw *hw) } /** - * ixgbe_read_phy_reg_mdi_22 - Read from a clause 22 PHY register without lock - * @hw: pointer to hardware structure - * @reg_addr: 32 bit address of PHY register to read - * @dev_type: always unused - * @phy_data: Pointer to read data from PHY register - */ -STATIC s32 ixgbe_read_phy_reg_mdi_22(struct ixgbe_hw *hw, u32 reg_addr, - u32 dev_type, u16 *phy_data) -{ - u32 i, data, command; - UNREFERENCED_1PARAMETER(dev_type); - - /* Setup and write the read command */ - command = (reg_addr << IXGBE_MSCA_DEV_TYPE_SHIFT) | - (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) | - IXGBE_MSCA_OLD_PROTOCOL | IXGBE_MSCA_READ_AUTOINC | - IXGBE_MSCA_MDI_COMMAND; - - IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); - - /* Check every 10 usec to see if the access completed. - * The MDI Command bit will clear when the operation is - * complete - */ - for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) { - usec_delay(10); - - command = IXGBE_READ_REG(hw, IXGBE_MSCA); - if (!(command & IXGBE_MSCA_MDI_COMMAND)) - break; - } - - if (command & IXGBE_MSCA_MDI_COMMAND) { - ERROR_REPORT1(IXGBE_ERROR_POLLING, - "PHY read command did not complete.\n"); - return IXGBE_ERR_PHY; - } - - /* Read operation is complete. Get the data from MSRWD */ - data = IXGBE_READ_REG(hw, IXGBE_MSRWD); - data >>= IXGBE_MSRWD_READ_DATA_SHIFT; - *phy_data = (u16)data; - - return IXGBE_SUCCESS; -} - -/** - * ixgbe_write_phy_reg_mdi_22 - Write to a clause 22 PHY register without lock - * @hw: pointer to hardware structure - * @reg_addr: 32 bit PHY register to write - * @dev_type: always unused - * @phy_data: Data to write to the PHY register - */ -STATIC s32 ixgbe_write_phy_reg_mdi_22(struct ixgbe_hw *hw, u32 reg_addr, - u32 dev_type, u16 phy_data) -{ - u32 i, command; - UNREFERENCED_1PARAMETER(dev_type); - - /* Put the data in the MDI single read and write data register*/ - IXGBE_WRITE_REG(hw, IXGBE_MSRWD, (u32)phy_data); - - /* Setup and write the write command */ - command = (reg_addr << IXGBE_MSCA_DEV_TYPE_SHIFT) | - (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) | - IXGBE_MSCA_OLD_PROTOCOL | IXGBE_MSCA_WRITE | - IXGBE_MSCA_MDI_COMMAND; - - IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); - - /* Check every 10 usec to see if the access completed. - * The MDI Command bit will clear when the operation is - * complete - */ - for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) { - usec_delay(10); - - command = IXGBE_READ_REG(hw, IXGBE_MSCA); - if (!(command & IXGBE_MSCA_MDI_COMMAND)) - break; - } - - if (command & IXGBE_MSCA_MDI_COMMAND) { - ERROR_REPORT1(IXGBE_ERROR_POLLING, - "PHY write cmd didn't complete\n"); - return IXGBE_ERR_PHY; - } - - return IXGBE_SUCCESS; -} - -/** * ixgbe_identify_phy_x550em - Get PHY type based on device id * @hw: pointer to hardware structure * @@ -467,14 +375,10 @@ STATIC s32 ixgbe_identify_phy_x550em(struct ixgbe_hw *hw) return ixgbe_identify_phy_generic(hw); case IXGBE_DEV_ID_X550EM_X_1G_T: hw->phy.type = ixgbe_phy_ext_1g_t; - hw->phy.ops.read_reg = NULL; - hw->phy.ops.write_reg = NULL; break; case IXGBE_DEV_ID_X550EM_A_1G_T: case IXGBE_DEV_ID_X550EM_A_1G_T_L: hw->phy.type = ixgbe_phy_fw; - hw->phy.ops.read_reg = NULL; - hw->phy.ops.write_reg = NULL; if (hw->bus.lan_id) hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM; else @@ -1764,9 +1668,12 @@ STATIC s32 ixgbe_restart_an_internal_phy_x550em(struct ixgbe_hw *hw) return status; } +#ifndef PREBOOT_SUPPORT /** * ixgbe_setup_sgmii - Set up link for sgmii * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg_wait: true when waiting for completion is needed */ STATIC s32 ixgbe_setup_sgmii(struct ixgbe_hw *hw, ixgbe_link_speed speed, bool autoneg_wait) @@ -1831,9 +1738,12 @@ STATIC s32 ixgbe_setup_sgmii(struct ixgbe_hw *hw, ixgbe_link_speed speed, return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait); } +#endif /* PREBOOT_SUPPORT */ /** - * ixgbe_setup_sgmii_fw - Set up link for sgmii with firmware-controlled PHYs + * ixgbe_setup_sgmii_fw - Set up link for internal PHY SGMII auto-negotiation * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg_wait: true when waiting for completion is needed */ STATIC s32 ixgbe_setup_sgmii_fw(struct ixgbe_hw *hw, ixgbe_link_speed speed, bool autoneg_wait) @@ -1953,7 +1863,11 @@ void ixgbe_init_mac_link_ops_X550em(struct ixgbe_hw *hw) case ixgbe_media_type_backplane: if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII || hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII_L) +#ifdef PREBOOT_SUPPORT + mac->ops.setup_link = ixgbe_setup_sgmii_fw; +#else mac->ops.setup_link = ixgbe_setup_sgmii; +#endif /* PREBOOT_SUPPORT */ break; default: break; @@ -2003,8 +1917,18 @@ s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw, } else { switch (hw->phy.type) { case ixgbe_phy_ext_1g_t: +#ifdef PREBOOT_SUPPORT + *speed = IXGBE_LINK_SPEED_1GB_FULL; + break; +#endif /* PREBOOT_SUPPORT */ case ixgbe_phy_sgmii: +#ifdef PREBOOT_SUPPORT + *speed = IXGBE_LINK_SPEED_1GB_FULL | + IXGBE_LINK_SPEED_100_FULL | + IXGBE_LINK_SPEED_10_FULL; +#else *speed = IXGBE_LINK_SPEED_1GB_FULL; +#endif /* PREBOOT_SUPPORT */ break; case ixgbe_phy_x550em_kr: if (hw->mac.type == ixgbe_mac_X550EM_a) { @@ -2376,10 +2300,10 @@ s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) switch (hw->device_id) { case IXGBE_DEV_ID_X550EM_A_1G_T: case IXGBE_DEV_ID_X550EM_A_1G_T_L: - phy->ops.read_reg_mdi = ixgbe_read_phy_reg_mdi_22; - phy->ops.write_reg_mdi = ixgbe_write_phy_reg_mdi_22; - hw->phy.ops.read_reg = ixgbe_read_phy_reg_x550a; - hw->phy.ops.write_reg = ixgbe_write_phy_reg_x550a; + phy->ops.read_reg_mdi = NULL; + phy->ops.write_reg_mdi = NULL; + hw->phy.ops.read_reg = NULL; + hw->phy.ops.write_reg = NULL; phy->ops.check_overtemp = ixgbe_check_overtemp_fw; if (hw->bus.lan_id) hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM; @@ -2400,6 +2324,9 @@ s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) /* set up for CS4227 usage */ hw->phy.phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM; break; + case IXGBE_DEV_ID_X550EM_X_1G_T: + phy->ops.read_reg_mdi = NULL; + phy->ops.write_reg_mdi = NULL; default: break; } @@ -2536,7 +2463,8 @@ s32 ixgbe_reset_hw_X550em(struct ixgbe_hw *hw) DEBUGOUT1("Failed to initialize PHY ops, STATUS = %d\n", status); - if (status == IXGBE_ERR_SFP_NOT_SUPPORTED) { + if (status == IXGBE_ERR_SFP_NOT_SUPPORTED || + status == IXGBE_ERR_PHY_ADDR_INVALID) { DEBUGOUT("Returning from reset HW due to PHY init failure\n"); return status; } @@ -2697,6 +2625,8 @@ s32 ixgbe_setup_kr_x550em(struct ixgbe_hw *hw) /** * ixgbe_setup_mac_link_sfp_x550em - Setup internal/external the PHY for SFP * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg_wait_to_complete: unused * * Configure the external PHY and the integrated KR PHY for SFP support. **/ @@ -2789,8 +2719,10 @@ STATIC s32 ixgbe_setup_sfi_x550a(struct ixgbe_hw *hw, ixgbe_link_speed *speed) /** * ixgbe_setup_mac_link_sfp_x550a - Setup internal PHY for SFP * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg_wait_to_complete: unused * - * Configure the the integrated PHY for SFP support. + * Configure the integrated PHY for SFP support. **/ s32 ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw, ixgbe_link_speed speed, @@ -3211,6 +3143,8 @@ s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, u16 *data) buffer.address = IXGBE_CPU_TO_BE32(offset * 2); /* one word */ buffer.length = IXGBE_CPU_TO_BE16(sizeof(u16)); + buffer.pad2 = 0; + buffer.pad3 = 0; status = hw->mac.ops.acquire_swfw_sync(hw, mask); if (status) @@ -3269,6 +3203,8 @@ s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw, /* convert offset from words to bytes */ buffer.address = IXGBE_CPU_TO_BE32((offset + current_word) * 2); buffer.length = IXGBE_CPU_TO_BE16(words_to_read * 2); + buffer.pad2 = 0; + buffer.pad3 = 0; status = ixgbe_hic_unlocked(hw, (u32 *)&buffer, sizeof(buffer), IXGBE_HI_COMMAND_TIMEOUT); @@ -3406,6 +3342,8 @@ out: * @ptr: pointer offset in eeprom * @size: size of section pointed by ptr, if 0 first word will be used as size * @csum: address of checksum to update + * @buffer: pointer to buffer containing calculated checksum + * @buffer_size: size of buffer * * Returns error status for any failure */ @@ -3740,7 +3678,13 @@ u64 ixgbe_get_supported_physical_layer_X550em(struct ixgbe_hw *hw) physical_layer |= IXGBE_PHYSICAL_LAYER_10BASE_T; break; case ixgbe_phy_sgmii: +#ifdef PREBOOT_SUPPORT + physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX | + IXGBE_PHYSICAL_LAYER_100BASE_TX | + IXGBE_PHYSICAL_LAYER_10BASE_T; +#else physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX; +#endif /* PREBOOT_SUPPORT */ break; case ixgbe_phy_ext_1g_t: physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T; @@ -3777,6 +3721,7 @@ s32 ixgbe_get_bus_info_X550em(struct ixgbe_hw *hw) /** * ixgbe_disable_rx_x550 - Disable RX unit + * @hw: pointer to hardware structure * * Enables the Rx DMA unit for x550 **/ @@ -4421,6 +4366,7 @@ STATIC void ixgbe_release_swfw_sync_X550a(struct ixgbe_hw *hw, u32 mask) * ixgbe_read_phy_reg_x550a - Reads specified PHY register * @hw: pointer to hardware structure * @reg_addr: 32 bit address of PHY register to read + * @device_type: 5 bit device type * @phy_data: Pointer to read data from PHY register * * Reads a value from a specified PHY register using the SWFW lock and PHY |