1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
|
.. BSD LICENSE
Copyright(c) 2017 Intel Corporation. All rights reserved.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
* Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in
the documentation and/or other materials provided with the
distribution.
* Neither the name of Intel Corporation nor the names of its
contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
"AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Cryptodev Scheduler Poll Mode Driver Library
============================================
Scheduler PMD is a software crypto PMD, which has the capabilities of
attaching hardware and/or software cryptodevs, and distributes ingress
crypto ops among them in a certain manner.
.. figure:: img/scheduler-overview.*
Cryptodev Scheduler Overview
The Cryptodev Scheduler PMD library (**librte_pmd_crypto_scheduler**) acts as
a software crypto PMD and shares the same API provided by librte_cryptodev.
The PMD supports attaching multiple crypto PMDs, software or hardware, as
slaves, and distributes the crypto workload to them with certain behavior.
The behaviors are categorizes as different "modes". Basically, a scheduling
mode defines certain actions for scheduling crypto ops to its slaves.
The librte_pmd_crypto_scheduler library exports a C API which provides an API
for attaching/detaching slaves, set/get scheduling modes, and enable/disable
crypto ops reordering.
Limitations
-----------
* Sessionless crypto operation is not supported
* OOP crypto operation is not supported when the crypto op reordering feature
is enabled.
Installation
------------
To build DPDK with CRYTPO_SCHEDULER_PMD the user is required to set
CONFIG_RTE_LIBRTE_PMD_CRYPTO_SCHEDULER=y in config/common_base, and
recompile DPDK
Initialization
--------------
To use the PMD in an application, user must:
* Call rte_vdev_init("crypto_scheduler") within the application.
* Use --vdev="crypto_scheduler" in the EAL options, which will call
rte_vdev_init() internally.
The following parameters (all optional) can be provided in the previous
two calls:
* socket_id: Specify the socket where the memory for the device is going
to be allocated (by default, socket_id will be the socket where the core
that is creating the PMD is running on).
* max_nb_sessions: Specify the maximum number of sessions that can be
created. This value may be overwritten internally if there are too
many devices are attached.
* slave: If a cryptodev has been initialized with specific name, it can be
attached to the scheduler using this parameter, simply filling the name
here. Multiple cryptodevs can be attached initially by presenting this
parameter multiple times.
* mode: Specify the scheduling mode of the PMD. The supported scheduling
mode parameter values are specified in the "Cryptodev Scheduler Modes
Overview" section.
* ordering: Specify the status of the crypto operations ordering feature.
The value of this parameter can be "enable" or "disable". This feature
is disabled by default.
Example:
.. code-block:: console
... --vdev "crypto_aesni_mb0,name=aesni_mb_1" --vdev "crypto_aesni_mb1,name=aesni_mb_2" --vdev "crypto_scheduler,slave=aesni_mb_1,slave=aesni_mb_2" ...
.. note::
* The scheduler cryptodev cannot be started unless the scheduling mode
is set and at least one slave is attached. Also, to configure the
scheduler in the run-time, like attach/detach slave(s), change
scheduling mode, or enable/disable crypto op ordering, one should stop
the scheduler first, otherwise an error will be returned.
* The crypto op reordering feature requires using the userdata field of
every mbuf to be processed to store temporary data. By the end of
processing, the field is set to pointing to NULL, any previously
stored value of this field will be lost.
Cryptodev Scheduler Modes Overview
----------------------------------
Currently the Crypto Scheduler PMD library supports following modes of
operation:
* **CDEV_SCHED_MODE_ROUNDROBIN:**
*Initialization mode parameter*: **round-robin**
Round-robin mode, which distributes the enqueued burst of crypto ops
among its slaves in a round-robin manner. This mode may help to fill
the throughput gap between the physical core and the existing cryptodevs
to increase the overall performance.
* **CDEV_SCHED_MODE_PKT_SIZE_DISTR:**
*Initialization mode parameter*: **packet-size-distr**
Packet-size based distribution mode, which works with 2 slaves, the primary
slave and the secondary slave, and distributes the enqueued crypto
operations to them based on their data lengths. A crypto operation will be
distributed to the primary slave if its data length is equal to or bigger
than the designated threshold, otherwise it will be handled by the secondary
slave.
A typical usecase in this mode is with the QAT cryptodev as the primary and
a software cryptodev as the secondary slave. This may help applications to
process additional crypto workload than what the QAT cryptodev can handle on
its own, by making use of the available CPU cycles to deal with smaller
crypto workloads.
The threshold is set to 128 bytes by default. It can be updated by calling
function **rte_cryptodev_scheduler_option_set**. The parameter of
**option_type** must be **CDEV_SCHED_OPTION_THRESHOLD** and **option** should
point to a rte_cryptodev_scheduler_threshold_option structure filled with
appropriate threshold value. Please NOTE this threshold has be a power-of-2
unsigned integer.
* **CDEV_SCHED_MODE_FAILOVER:**
*Initialization mode parameter*: **fail-over**
Fail-over mode, which works with 2 slaves, the primary slave and the
secondary slave. In this mode, the scheduler will enqueue the incoming
crypto operation burst to the primary slave. When one or more crypto
operations fail to be enqueued, then they will be enqueued to the secondary
slave.
* **CDEV_SCHED_MODE_MULTICORE:**
*Initialization mode parameter*: **multi-core**
Multi-core mode, which distributes the workload with several (up to eight)
worker cores. The enqueued bursts are distributed among the worker cores in a
round-robin manner. If scheduler cannot enqueue entire burst to the same worker,
it will enqueue the remaining operations to the next available worker.
For pure small packet size (64 bytes) traffic however the multi-core mode is not
an optimal solution, as it doesn't give significant per-core performance improvement.
For mixed traffic (IMIX) the optimal number of worker cores is around 2-3.
For large packets (1.5 Kbytes) scheduler shows linear scaling in performance
up to eight cores.
Each worker uses its own slave cryptodev. Only software cryptodevs
are supported. Only the same type of cryptodevs should be used concurrently.
The multi-core mode uses one extra parameter:
* corelist: Semicolon-separated list of logical cores to be used as workers.
The number of worker cores should be equal to the number of slave cryptodevs.
These cores should be present in EAL core list parameter and
should not be used by the application or any other process.
Example:
... --vdev "crypto_aesni_mb1,name=aesni_mb_1" --vdev "crypto_aesni_mb_pmd2,name=aesni_mb_2" \
--vdev "crypto_scheduler,slave=aesni_mb_1,slave=aesni_mb_2,mode=multi-core,corelist=23;24" ...
|
