blob: 8038bf205eea1c863dd875828f0165e9662d6ac3 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
|
.. SPDX-License-Identifier: BSD-3-Clause
Copyright 2018 NXP
ENETC Poll Mode Driver
======================
The ENETC NIC PMD (**librte_pmd_enetc**) provides poll mode driver
support for the inbuilt NIC found in the **NXP LS1028** SoC.
More information can be found at `NXP Official Website
<https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/qoriq-layerscape-arm-processors/qoriq-layerscape-1028a-industrial-applications-processor:LS1028A>`_.
ENETC
-----
This section provides an overview of the NXP ENETC
and how it is integrated into the DPDK.
Contents summary
- ENETC overview
- ENETC features
- PCI bus driver
- NIC driver
- Supported ENETC SoCs
- Prerequisites
- Driver compilation and testing
ENETC Overview
~~~~~~~~~~~~~~
ENETC is a PCI Integrated End Point(IEP). IEP implements
peripheral devices in an SoC such that software sees them as PCIe device.
ENETC is an evolution of BDR(Buffer Descriptor Ring) based networking
IPs.
This infrastructure simplifies adding support for IEP and facilitates in following:
- Device discovery and location
- Resource requirement discovery and allocation (e.g. interrupt assignment,
device register address)
- Event reporting
ENETC Features
~~~~~~~~~~~~~~
- Link Status
- Packet type information
NIC Driver (PMD)
~~~~~~~~~~~~~~~~
ENETC PMD is traditional DPDK PMD which provides necessary interface between
RTE framework and ENETC internal drivers.
- Driver registers the device vendor table in PCI subsystem.
- RTE framework scans the PCI bus for connected devices.
- This scanning will invoke the probe function of ENETC driver.
- The probe function will set the basic device registers and also setups BD rings.
- On packet Rx the respective BD Ring status bit is set which is then used for
packet processing.
- Then Tx is done first followed by Rx.
Supported ENETC SoCs
~~~~~~~~~~~~~~~~~~~~
- LS1028
Prerequisites
~~~~~~~~~~~~~
There are three main pre-requisities for executing ENETC PMD on a ENETC
compatible board:
1. **ARM 64 Tool Chain**
For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-linux-gnu/gcc-linaro-7.3.1-2018.05-i686_aarch64-linux-gnu.tar.xz>`_.
2. **Linux Kernel**
It can be obtained from `NXP's Github hosting <https://source.codeaurora.org/external/qoriq/qoriq-components/linux>`_.
3. **Rootfile system**
Any *aarch64* supporting filesystem can be used. For example,
Ubuntu 16.04 LTS (Xenial) or 18.04 (Bionic) userland which can be obtained
from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/18.04/release/ubuntu-base-18.04.1-base-arm64.tar.gz>`_.
The following dependencies are not part of DPDK and must be installed
separately:
- **NXP Linux LSDK**
NXP Layerscape software development kit (LSDK) includes support for family
of QorIQ® ARM-Architecture-based system on chip (SoC) processors
and corresponding boards.
It includes the Linux board support packages (BSPs) for NXP SoCs,
a fully operational tool chain, kernel and board specific modules.
LSDK and related information can be obtained from: `LSDK <https://www.nxp.com/support/developer-resources/run-time-software/linux-software-and-development-tools/layerscape-software-development-kit:LAYERSCAPE-SDK>`_
Driver compilation and testing
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Follow instructions available in the document
:ref:`compiling and testing a PMD for a NIC <pmd_build_and_test>`
to launch **testpmd**
To compile in performance mode, please set ``CONFIG_RTE_CACHE_LINE_SIZE=64``
|
