diff options
Diffstat (limited to 'nat/nat-api')
| -rw-r--r-- | nat/nat-api/src/main/yang/ietf-nat@2018-06-28.yang (renamed from nat/nat-api/src/main/yang/ietf-nat@2018-02-23.yang) | 24 |
1 files changed, 3 insertions, 21 deletions
diff --git a/nat/nat-api/src/main/yang/ietf-nat@2018-02-23.yang b/nat/nat-api/src/main/yang/ietf-nat@2018-06-28.yang index 5eec4c609..e67065fb7 100644 --- a/nat/nat-api/src/main/yang/ietf-nat@2018-02-23.yang +++ b/nat/nat-api/src/main/yang/ietf-nat@2018-06-28.yang @@ -66,7 +66,7 @@ module ietf-nat { This version of this YANG module is part of RFC XXXX; see the RFC itself for full legal notices."; - revision 2018-02-23 { + revision 2018-06-28 { description "Initial revision."; reference @@ -310,7 +310,6 @@ module ietf-nat { case port-range { uses port-number; } - case port-set-algo { leaf psid-offset { type uint8 { @@ -453,6 +452,7 @@ module ietf-nat { description "Source port of the packet sent on an external interface of the NAT. + It is used also to indicate the external source ICMP identifier."; @@ -502,7 +502,6 @@ module ietf-nat { uses port-number; } - leaf lifetime { type uint32; units "seconds"; @@ -839,7 +838,6 @@ module ietf-nat { If supported, this mode of operation should be configurable, and it should be disabled by default in general-purpose NAT devices. - If one single per-interface binding behavior is supported by a NAT, this parameter is by default set to that behavior."; reference @@ -1032,7 +1030,6 @@ module ietf-nat { "Provides one or a list of NAT64 prefixes with or without a list of destination IPv4 prefixes. It allows mapping IPv4 address ranges to IPv6 prefixes. - For example: 192.0.2.0/24 is mapped to 2001:db8:122:300::/56. 198.51.100.0/24 is mapped to 2001:db8:122::/48."; @@ -1127,6 +1124,7 @@ module ietf-nat { default false; description "Enable/Disable destination NAT. + A NAT44 may be configured to enable Destination NAT, too."; } @@ -1368,7 +1366,6 @@ module ietf-nat { reference "Section 5 of RFC 4787."; } - enum "edf" { description "address-and-port-dependent-filtering"; @@ -1417,7 +1414,6 @@ module ietf-nat { "Configures a port quota to be assigned per subscriber. It corresponds to the maximum number of ports to be used by a subscriber."; - leaf port-limit { type uint16; description @@ -1659,7 +1655,6 @@ module ietf-nat { "The transport protocol used by the ALG (e.g., TCP, UDP)."; } - container dst-transport-port { uses port-number; description @@ -1852,7 +1847,6 @@ module ietf-nat { description "Information about the configuration parameters that rate limit the translation based upon various criteria."; - leaf limit-per-subscriber { type uint32; units "bits/second"; @@ -1864,8 +1858,6 @@ module ietf-nat { leaf limit-per-instance { type uint32; units "bits/second"; - // TODO(HC2VPP-328) - // mandatory true; description "Rate-limit the number of new mappings and sessions per instance."; @@ -1961,15 +1953,6 @@ module ietf-nat { } } - leaf logging-enable { - if-feature "basic-nat44 or napt44 or nat64"; - type boolean; - description - "Enable logging features."; - reference - "Section 2.3 of RFC 6908 and REQ-12 of RFC 6888."; - } - container mapping-table { if-feature "basic-nat44 or napt44 " + "or nat64 or clat or dst-nat"; @@ -2152,7 +2135,6 @@ module ietf-nat { A subscriber is identified by a subnet, subscriber-mask, etc."; } - leaf total-address-mappings { if-feature "basic-nat44 or napt44 " + "or nat64 or clat or dst-nat"; |