| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
despite VPP DHCP client setting neither ciaddr nor giaddr and setting the broadcast bit (see RFC 2131 section 4.1) some DHCP servers will still send a unicast DCHPACK. So as not to drop this VPP must have both 1) a receive FIB entry for the OFFERED IP adress and 2) a 'don't drop me because of uRPF' FIB entry for the DHCP server's address.
Change-Id: I167d858deb45629318cbdccf5bf67d971730a42f
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
there are, intentionally, no validation checks in the ARP/ND code to prevent an ARP/ND entry from being installed for an address that is not local to the interface's sub-net. This is ok, since the adjacency/FIB code is designed to handle this case using the 'refinement' criteria - i.e. only installing a FIB entry for the address if the address 'refines' (i.e. is more specific than) the interface's sub-net.
However, the refinement criteria currently operates on the FIB entry's prefix (which is a /32, so on the address) and not on the next-hop in the path.
So, enter multiple ARP entries for the same address on different links, and this refinement criteria uses only the last added path, and so will remove the FIB entry should the ARP entries be added in the 'wrong' order.
This fix updates the refinement criteria to work on each path of the FIB entry. The entry is installed if one of the paths refines the covers and only paths refining the cover contribute forwarding.
Per-path refinement checks are stored in path-extensions. The patch is rather large as path-extension, which were previously used only for out-going MPLS labels, have been generalized.
Change-Id: I00be359148cb948c32c52109e832a70537a7920a
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I961685a2a0e4c314049444c64eb6ccf877c278dd
Signed-off-by: Pablo Camarillo <pcamaril@cisco.com>
|
|
- the flow hash config is (and was) cached on the load-balance object so the fib_table_t struct is not used a switch time. Therefore changes to the table's flow hash config need to be propagated to all load-balances and hance all FIB entries in the table.
- enable API for setting the IPv6 table flow hash config
- use only the hash config in the fib_table_t object and not on the ipX_fib_t
- add tests.
Change-Id: Ib804c11162c6d4972c764957562c372f663e05d4
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
1 - interface-DPO
Used in the Data-plane to change a packet's input interface
2 - MPLS multicast FIB entry
Same as a unicast entry but it links to a replicate not a load-balance DPO
3 - Multicast MPLS tunnel
Update MPLS tunnels to use a FIB path-list to describe the endpoint[s]. Use the path-list to generate the forwarding chain (DPOs) to link to .
4 - Resolve a path via a local label (of an mLDP LSP)
For IP multicast entries to use an LSP in the replication list, we need to decribe the 'resolve-via-label' where the label is that of a multicast LSP.
5 - MPLS disposition path sets RPF-ID
For a interface-less LSP (i.e. mLDP not RSVP-TE) at the tail of the LSP we still need to perform an RPF check. An MPLS disposition DPO performs the MPLS pop validation checks and sets the RPF-ID in the packet.
6 - RPF check with per-entry RPF-ID
An RPF-ID is used instead of a real interface SW if index in the case the IP traffic arrives from an LSP that does not have an associated interface.
Change-Id: Ib92e177be919147bafeb599729abf3d1abc2f4b3
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
- single-hop BFD: attach a delegate to the appropriate adjacency
- multi-hop BFD [not supported yet]: attach a delegate to the FIB entry.
adjacency/fib_entry state tracks the BFD session state. when the state is down the object does not contribute forwarding hence and hence dependent objects will not use it.
For example, if a route is ECMP via two adjacencies and one of them is BFD down, then only the other is used to forward (i.e. we don't drop half the traffic).
Change-Id: I0ef53e20e73b067001a132cd0a3045408811a822
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
bridging. That is hosts in one sub-net reachable via differenet interfaces.
Introducate a new API command:
ip6 nd proxy <host-address> <interface>
this indicates 2 things;
1) that host <host-address> is reachable out of interface <interface>. VPP will thus install that route.
2) NS requests sent to <host-address> will be responeded to (i.e. proxied).
Change-Id: I863f967fdb5097ab3b574769c70afdbfc8d5478a
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I6d2afda991d771fb4a89fc3f6544f8e940a9b9f0
Signed-off-by: Shwetha Bhandari <shwethab@cisco.com>
|
|
- IPv[46] mfib tables with support for (*,G/m), (*,G) and (S,G) exact and longest prefix match
- Replication represented via a new replicate DPO.
- RPF configuration and data-plane checking
- data-plane signals sent to listening control planes.
The functions of multicast forwarding entries differ from their unicast conterparts, so we introduce a new mfib_table_t and mfib_entry_t objects. However, we re-use the fib_path_list to resolve and build the entry's output list. the fib_path_list provides the service to construct a replicate DPO for multicast.
'make tests' is added to with two new suites; TEST=mfib, this is invocation of the CLI command 'test mfib' which deals with many path add/remove, flag set/unset scenarios, TEST=ip-mcast, data-plane forwarding tests.
Updated applications to use the new MIFB functions;
- IPv6 NS/RA.
- DHCPv6
unit tests for these are undated accordingly.
Change-Id: I49ec37b01f1b170335a5697541c8fd30e6d3a961
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I7b51f88292e057c6443b12224486f2d0c9f8ae23
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
Neale Ranns
Pablo Camarillo
Shwetha Bhandari
Damjan Marion