diff options
Diffstat (limited to 'src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_defines.h')
| -rwxr-xr-x | src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_defines.h | 1380 |
1 files changed, 1380 insertions, 0 deletions
diff --git a/src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_defines.h b/src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_defines.h new file mode 100755 index 00000000..63b228c5 --- /dev/null +++ b/src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_defines.h @@ -0,0 +1,1380 @@ +/******************************************************************************* + + Intel(R) Gigabit Ethernet Linux driver + Copyright(c) 2007-2013 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + +#ifndef _E1000_DEFINES_H_ +#define _E1000_DEFINES_H_ + +/* Number of Transmit and Receive Descriptors must be a multiple of 8 */ +#define REQ_TX_DESCRIPTOR_MULTIPLE 8 +#define REQ_RX_DESCRIPTOR_MULTIPLE 8 + +/* Definitions for power management and wakeup registers */ +/* Wake Up Control */ +#define E1000_WUC_APME 0x00000001 /* APM Enable */ +#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */ +#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */ +#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */ +#define E1000_WUC_PHY_WAKE 0x00000100 /* if PHY supports wakeup */ + +/* Wake Up Filter Control */ +#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */ +#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */ +#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ +#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */ +#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ +#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */ +#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */ +#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */ + +/* Wake Up Status */ +#define E1000_WUS_LNKC E1000_WUFC_LNKC +#define E1000_WUS_MAG E1000_WUFC_MAG +#define E1000_WUS_EX E1000_WUFC_EX +#define E1000_WUS_MC E1000_WUFC_MC +#define E1000_WUS_BC E1000_WUFC_BC + +/* Extended Device Control */ +#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* SW Definable Pin 4 data */ +#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* SW Definable Pin 6 data */ +#define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* SW Definable Pin 3 data */ +#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */ +#define E1000_CTRL_EXT_SDP3_DIR 0x00000800 /* Direction of SDP3 0=in 1=out */ +#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */ +/* Physical Func Reset Done Indication */ +#define E1000_CTRL_EXT_PFRSTD 0x00004000 +#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */ +#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */ +#define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clk Gating */ +#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 +/* Offset of the link mode field in Ctrl Ext register */ +#define E1000_CTRL_EXT_LINK_MODE_OFFSET 22 +#define E1000_CTRL_EXT_LINK_MODE_1000BASE_KX 0x00400000 +#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000 +#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000 +#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000 +#define E1000_CTRL_EXT_EIAME 0x01000000 +#define E1000_CTRL_EXT_IRCA 0x00000001 +#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Drv loaded bit for FW */ +#define E1000_CTRL_EXT_IAME 0x08000000 /* Int ACK Auto-mask */ +#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */ +#define E1000_I2CCMD_REG_ADDR_SHIFT 16 +#define E1000_I2CCMD_PHY_ADDR_SHIFT 24 +#define E1000_I2CCMD_OPCODE_READ 0x08000000 +#define E1000_I2CCMD_OPCODE_WRITE 0x00000000 +#define E1000_I2CCMD_READY 0x20000000 +#define E1000_I2CCMD_ERROR 0x80000000 +#define E1000_I2CCMD_SFP_DATA_ADDR(a) (0x0000 + (a)) +#define E1000_I2CCMD_SFP_DIAG_ADDR(a) (0x0100 + (a)) +#define E1000_MAX_SGMII_PHY_REG_ADDR 255 +#define E1000_I2CCMD_PHY_TIMEOUT 200 +#define E1000_IVAR_VALID 0x80 +#define E1000_GPIE_NSICR 0x00000001 +#define E1000_GPIE_MSIX_MODE 0x00000010 +#define E1000_GPIE_EIAME 0x40000000 +#define E1000_GPIE_PBA 0x80000000 + +/* Receive Descriptor bit definitions */ +#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */ +#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */ +#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */ +#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */ +#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */ +#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */ +#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */ +#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */ +#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */ +#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */ +#define E1000_RXD_STAT_DYNINT 0x800 /* Pkt caused INT via DYNINT */ +#define E1000_RXD_ERR_CE 0x01 /* CRC Error */ +#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */ +#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */ +#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */ +#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */ +#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */ +#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */ +#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */ + +#define E1000_RXDEXT_STATERR_TST 0x00000100 /* Time Stamp taken */ +#define E1000_RXDEXT_STATERR_LB 0x00040000 +#define E1000_RXDEXT_STATERR_CE 0x01000000 +#define E1000_RXDEXT_STATERR_SE 0x02000000 +#define E1000_RXDEXT_STATERR_SEQ 0x04000000 +#define E1000_RXDEXT_STATERR_CXE 0x10000000 +#define E1000_RXDEXT_STATERR_TCPE 0x20000000 +#define E1000_RXDEXT_STATERR_IPE 0x40000000 +#define E1000_RXDEXT_STATERR_RXE 0x80000000 + +/* mask to determine if packets should be dropped due to frame errors */ +#define E1000_RXD_ERR_FRAME_ERR_MASK ( \ + E1000_RXD_ERR_CE | \ + E1000_RXD_ERR_SE | \ + E1000_RXD_ERR_SEQ | \ + E1000_RXD_ERR_CXE | \ + E1000_RXD_ERR_RXE) + +/* Same mask, but for extended and packet split descriptors */ +#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \ + E1000_RXDEXT_STATERR_CE | \ + E1000_RXDEXT_STATERR_SE | \ + E1000_RXDEXT_STATERR_SEQ | \ + E1000_RXDEXT_STATERR_CXE | \ + E1000_RXDEXT_STATERR_RXE) + +#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000 +#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000 +#define E1000_MRQC_RSS_FIELD_IPV4 0x00020000 +#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000 +#define E1000_MRQC_RSS_FIELD_IPV6 0x00100000 +#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000 + +#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000 + +/* Management Control */ +#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */ +#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */ +#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */ +#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */ +#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */ +/* Enable MAC address filtering */ +#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 +/* Enable MNG packets to host memory */ +#define E1000_MANC_EN_MNG2HOST 0x00200000 + +#define E1000_MANC2H_PORT_623 0x00000020 /* Port 0x26f */ +#define E1000_MANC2H_PORT_664 0x00000040 /* Port 0x298 */ +#define E1000_MDEF_PORT_623 0x00000800 /* Port 0x26f */ +#define E1000_MDEF_PORT_664 0x00000400 /* Port 0x298 */ + +/* Receive Control */ +#define E1000_RCTL_RST 0x00000001 /* Software reset */ +#define E1000_RCTL_EN 0x00000002 /* enable */ +#define E1000_RCTL_SBP 0x00000004 /* store bad packet */ +#define E1000_RCTL_UPE 0x00000008 /* unicast promisc enable */ +#define E1000_RCTL_MPE 0x00000010 /* multicast promisc enable */ +#define E1000_RCTL_LPE 0x00000020 /* long packet enable */ +#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */ +#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */ +#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */ +#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */ +#define E1000_RCTL_RDMTS_HALF 0x00000000 /* Rx desc min thresh size */ +#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */ +#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */ +#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ +/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */ +#define E1000_RCTL_SZ_2048 0x00000000 /* Rx buffer size 2048 */ +#define E1000_RCTL_SZ_1024 0x00010000 /* Rx buffer size 1024 */ +#define E1000_RCTL_SZ_512 0x00020000 /* Rx buffer size 512 */ +#define E1000_RCTL_SZ_256 0x00030000 /* Rx buffer size 256 */ +/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */ +#define E1000_RCTL_SZ_16384 0x00010000 /* Rx buffer size 16384 */ +#define E1000_RCTL_SZ_8192 0x00020000 /* Rx buffer size 8192 */ +#define E1000_RCTL_SZ_4096 0x00030000 /* Rx buffer size 4096 */ +#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */ +#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */ +#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */ +#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */ +#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */ +#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */ +#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */ + +/* Use byte values for the following shift parameters + * Usage: + * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) & + * E1000_PSRCTL_BSIZE0_MASK) | + * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) & + * E1000_PSRCTL_BSIZE1_MASK) | + * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) & + * E1000_PSRCTL_BSIZE2_MASK) | + * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |; + * E1000_PSRCTL_BSIZE3_MASK)) + * where value0 = [128..16256], default=256 + * value1 = [1024..64512], default=4096 + * value2 = [0..64512], default=4096 + * value3 = [0..64512], default=0 + */ + +#define E1000_PSRCTL_BSIZE0_MASK 0x0000007F +#define E1000_PSRCTL_BSIZE1_MASK 0x00003F00 +#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000 +#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000 + +#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */ +#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */ +#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */ +#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */ + +/* SWFW_SYNC Definitions */ +#define E1000_SWFW_EEP_SM 0x01 +#define E1000_SWFW_PHY0_SM 0x02 +#define E1000_SWFW_PHY1_SM 0x04 +#define E1000_SWFW_CSR_SM 0x08 +#define E1000_SWFW_PHY2_SM 0x20 +#define E1000_SWFW_PHY3_SM 0x40 +#define E1000_SWFW_SW_MNG_SM 0x400 + +/* Device Control */ +#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */ +#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */ +#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master reqs */ +#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */ +#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */ +#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */ +#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */ +#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */ +#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */ +#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */ +#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */ +#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */ +#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ +#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ +#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ +#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */ +#define E1000_CTRL_ADVD3WUC 0x00100000 /* D3 WUC */ +#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */ +#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */ +#define E1000_CTRL_RST 0x04000000 /* Global reset */ +#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */ +#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */ +#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ +#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ +#define E1000_CTRL_I2C_ENA 0x02000000 /* I2C enable */ + + +#define E1000_CONNSW_ENRGSRC 0x4 +#define E1000_CONNSW_PHYSD 0x400 +#define E1000_CONNSW_PHY_PDN 0x800 +#define E1000_CONNSW_SERDESD 0x200 +#define E1000_CONNSW_AUTOSENSE_CONF 0x2 +#define E1000_CONNSW_AUTOSENSE_EN 0x1 +#define E1000_PCS_CFG_PCS_EN 8 +#define E1000_PCS_LCTL_FLV_LINK_UP 1 +#define E1000_PCS_LCTL_FSV_10 0 +#define E1000_PCS_LCTL_FSV_100 2 +#define E1000_PCS_LCTL_FSV_1000 4 +#define E1000_PCS_LCTL_FDV_FULL 8 +#define E1000_PCS_LCTL_FSD 0x10 +#define E1000_PCS_LCTL_FORCE_LINK 0x20 +#define E1000_PCS_LCTL_FORCE_FCTRL 0x80 +#define E1000_PCS_LCTL_AN_ENABLE 0x10000 +#define E1000_PCS_LCTL_AN_RESTART 0x20000 +#define E1000_PCS_LCTL_AN_TIMEOUT 0x40000 +#define E1000_ENABLE_SERDES_LOOPBACK 0x0410 + +#define E1000_PCS_LSTS_LINK_OK 1 +#define E1000_PCS_LSTS_SPEED_100 2 +#define E1000_PCS_LSTS_SPEED_1000 4 +#define E1000_PCS_LSTS_DUPLEX_FULL 8 +#define E1000_PCS_LSTS_SYNK_OK 0x10 +#define E1000_PCS_LSTS_AN_COMPLETE 0x10000 + +/* Device Status */ +#define E1000_STATUS_FD 0x00000001 /* Duplex 0=half 1=full */ +#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */ +#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */ +#define E1000_STATUS_FUNC_SHIFT 2 +#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */ +#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */ +#define E1000_STATUS_SPEED_MASK 0x000000C0 +#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */ +#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ +#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ +#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Compltn by NVM */ +#define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */ +#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Master request status */ +#define E1000_STATUS_2P5_SKU 0x00001000 /* Val of 2.5GBE SKU strap */ +#define E1000_STATUS_2P5_SKU_OVER 0x00002000 /* Val of 2.5GBE SKU Over */ + +#define SPEED_10 10 +#define SPEED_100 100 +#define SPEED_1000 1000 +#define SPEED_2500 2500 +#define HALF_DUPLEX 1 +#define FULL_DUPLEX 2 + + +#define ADVERTISE_10_HALF 0x0001 +#define ADVERTISE_10_FULL 0x0002 +#define ADVERTISE_100_HALF 0x0004 +#define ADVERTISE_100_FULL 0x0008 +#define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */ +#define ADVERTISE_1000_FULL 0x0020 + +/* 1000/H is not supported, nor spec-compliant. */ +#define E1000_ALL_SPEED_DUPLEX ( \ + ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \ + ADVERTISE_100_FULL | ADVERTISE_1000_FULL) +#define E1000_ALL_NOT_GIG ( \ + ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \ + ADVERTISE_100_FULL) +#define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL) +#define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL) +#define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF) + +#define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX + +/* LED Control */ +#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F +#define E1000_LEDCTL_LED0_MODE_SHIFT 0 +#define E1000_LEDCTL_LED0_IVRT 0x00000040 +#define E1000_LEDCTL_LED0_BLINK 0x00000080 + +#define E1000_LEDCTL_MODE_LED_ON 0xE +#define E1000_LEDCTL_MODE_LED_OFF 0xF + +/* Transmit Descriptor bit definitions */ +#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */ +#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */ +#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */ +#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */ +#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */ +#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */ +#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */ +#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */ +#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */ +#define E1000_TXD_CMD_DEXT 0x20000000 /* Desc extension (0 = legacy) */ +#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */ +#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */ +#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */ +#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */ +#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */ +#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */ +#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */ +#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */ +#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */ +#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */ +#define E1000_TXD_EXTCMD_TSTAMP 0x00000010 /* IEEE1588 Timestamp packet */ + +/* Transmit Control */ +#define E1000_TCTL_EN 0x00000002 /* enable Tx */ +#define E1000_TCTL_PSP 0x00000008 /* pad short packets */ +#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */ +#define E1000_TCTL_COLD 0x003ff000 /* collision distance */ +#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ +#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */ + +/* Transmit Arbitration Count */ +#define E1000_TARC0_ENABLE 0x00000400 /* Enable Tx Queue 0 */ + +/* SerDes Control */ +#define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400 +#define E1000_SCTL_ENABLE_SERDES_LOOPBACK 0x0410 + +/* Receive Checksum Control */ +#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */ +#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */ +#define E1000_RXCSUM_CRCOFL 0x00000800 /* CRC32 offload enable */ +#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */ +#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */ + +/* Header split receive */ +#define E1000_RFCTL_NFSW_DIS 0x00000040 +#define E1000_RFCTL_NFSR_DIS 0x00000080 +#define E1000_RFCTL_ACK_DIS 0x00001000 +#define E1000_RFCTL_EXTEN 0x00008000 +#define E1000_RFCTL_IPV6_EX_DIS 0x00010000 +#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000 +#define E1000_RFCTL_LEF 0x00040000 + +/* Collision related configuration parameters */ +#define E1000_COLLISION_THRESHOLD 15 +#define E1000_CT_SHIFT 4 +#define E1000_COLLISION_DISTANCE 63 +#define E1000_COLD_SHIFT 12 + +/* Default values for the transmit IPG register */ +#define DEFAULT_82543_TIPG_IPGT_FIBER 9 +#define DEFAULT_82543_TIPG_IPGT_COPPER 8 + +#define E1000_TIPG_IPGT_MASK 0x000003FF + +#define DEFAULT_82543_TIPG_IPGR1 8 +#define E1000_TIPG_IPGR1_SHIFT 10 + +#define DEFAULT_82543_TIPG_IPGR2 6 +#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7 +#define E1000_TIPG_IPGR2_SHIFT 20 + +/* Ethertype field values */ +#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */ + +#define ETHERNET_FCS_SIZE 4 +#define MAX_JUMBO_FRAME_SIZE 0x3F00 + +/* Extended Configuration Control and Size */ +#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020 +#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001 +#define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE 0x00000008 +#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020 +#define E1000_EXTCNF_CTRL_GATE_PHY_CFG 0x00000080 +#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000 +#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16 +#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK 0x0FFF0000 +#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT 16 + +#define E1000_PHY_CTRL_D0A_LPLU 0x00000002 +#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004 +#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008 +#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040 + +#define E1000_KABGTXD_BGSQLBIAS 0x00050000 + +/* PBA constants */ +#define E1000_PBA_8K 0x0008 /* 8KB */ +#define E1000_PBA_10K 0x000A /* 10KB */ +#define E1000_PBA_12K 0x000C /* 12KB */ +#define E1000_PBA_14K 0x000E /* 14KB */ +#define E1000_PBA_16K 0x0010 /* 16KB */ +#define E1000_PBA_18K 0x0012 +#define E1000_PBA_20K 0x0014 +#define E1000_PBA_22K 0x0016 +#define E1000_PBA_24K 0x0018 +#define E1000_PBA_26K 0x001A +#define E1000_PBA_30K 0x001E +#define E1000_PBA_32K 0x0020 +#define E1000_PBA_34K 0x0022 +#define E1000_PBA_35K 0x0023 +#define E1000_PBA_38K 0x0026 +#define E1000_PBA_40K 0x0028 +#define E1000_PBA_48K 0x0030 /* 48KB */ +#define E1000_PBA_64K 0x0040 /* 64KB */ + +#define E1000_PBA_RXA_MASK 0xFFFF + +#define E1000_PBS_16K E1000_PBA_16K + +#define IFS_MAX 80 +#define IFS_MIN 40 +#define IFS_RATIO 4 +#define IFS_STEP 10 +#define MIN_NUM_XMITS 1000 + +/* SW Semaphore Register */ +#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */ +#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */ +#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */ + +#define E1000_SWSM2_LOCK 0x00000002 /* Secondary driver semaphore bit */ + +/* Interrupt Cause Read */ +#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */ +#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */ +#define E1000_ICR_LSC 0x00000004 /* Link Status Change */ +#define E1000_ICR_RXSEQ 0x00000008 /* Rx sequence error */ +#define E1000_ICR_RXDMT0 0x00000010 /* Rx desc min. threshold (0) */ +#define E1000_ICR_RXO 0x00000040 /* Rx overrun */ +#define E1000_ICR_RXT0 0x00000080 /* Rx timer intr (ring 0) */ +#define E1000_ICR_VMMB 0x00000100 /* VM MB event */ +#define E1000_ICR_RXCFG 0x00000400 /* Rx /c/ ordered set */ +#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */ +#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */ +#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */ +#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */ +#define E1000_ICR_TXD_LOW 0x00008000 +#define E1000_ICR_MNG 0x00040000 /* Manageability event */ +#define E1000_ICR_TS 0x00080000 /* Time Sync Interrupt */ +#define E1000_ICR_DRSTA 0x40000000 /* Device Reset Asserted */ +/* If this bit asserted, the driver should claim the interrupt */ +#define E1000_ICR_INT_ASSERTED 0x80000000 +#define E1000_ICR_DOUTSYNC 0x10000000 /* NIC DMA out of sync */ +#define E1000_ICR_FER 0x00400000 /* Fatal Error */ + +#define E1000_ICR_THS 0x00800000 /* ICR.THS: Thermal Sensor Event*/ +#define E1000_ICR_MDDET 0x10000000 /* Malicious Driver Detect */ + + +/* Extended Interrupt Cause Read */ +#define E1000_EICR_RX_QUEUE0 0x00000001 /* Rx Queue 0 Interrupt */ +#define E1000_EICR_RX_QUEUE1 0x00000002 /* Rx Queue 1 Interrupt */ +#define E1000_EICR_RX_QUEUE2 0x00000004 /* Rx Queue 2 Interrupt */ +#define E1000_EICR_RX_QUEUE3 0x00000008 /* Rx Queue 3 Interrupt */ +#define E1000_EICR_TX_QUEUE0 0x00000100 /* Tx Queue 0 Interrupt */ +#define E1000_EICR_TX_QUEUE1 0x00000200 /* Tx Queue 1 Interrupt */ +#define E1000_EICR_TX_QUEUE2 0x00000400 /* Tx Queue 2 Interrupt */ +#define E1000_EICR_TX_QUEUE3 0x00000800 /* Tx Queue 3 Interrupt */ +#define E1000_EICR_TCP_TIMER 0x40000000 /* TCP Timer */ +#define E1000_EICR_OTHER 0x80000000 /* Interrupt Cause Active */ +/* TCP Timer */ +#define E1000_TCPTIMER_KS 0x00000100 /* KickStart */ +#define E1000_TCPTIMER_COUNT_ENABLE 0x00000200 /* Count Enable */ +#define E1000_TCPTIMER_COUNT_FINISH 0x00000400 /* Count finish */ +#define E1000_TCPTIMER_LOOP 0x00000800 /* Loop */ + +/* This defines the bits that are set in the Interrupt Mask + * Set/Read Register. Each bit is documented below: + * o RXT0 = Receiver Timer Interrupt (ring 0) + * o TXDW = Transmit Descriptor Written Back + * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) + * o RXSEQ = Receive Sequence Error + * o LSC = Link Status Change + */ +#define IMS_ENABLE_MASK ( \ + E1000_IMS_RXT0 | \ + E1000_IMS_TXDW | \ + E1000_IMS_RXDMT0 | \ + E1000_IMS_RXSEQ | \ + E1000_IMS_LSC) + +/* Interrupt Mask Set */ +#define E1000_IMS_TXDW E1000_ICR_TXDW /* Tx desc written back */ +#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ +#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */ +#define E1000_IMS_VMMB E1000_ICR_VMMB /* Mail box activity */ +#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */ +#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */ +#define E1000_IMS_RXO E1000_ICR_RXO /* Rx overrun */ +#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* Rx timer intr */ +#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW +#define E1000_IMS_TS E1000_ICR_TS /* Time Sync Interrupt */ +#define E1000_IMS_DRSTA E1000_ICR_DRSTA /* Device Reset Asserted */ +#define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */ +#define E1000_IMS_FER E1000_ICR_FER /* Fatal Error */ + +#define E1000_IMS_THS E1000_ICR_THS /* ICR.TS: Thermal Sensor Event*/ +#define E1000_IMS_MDDET E1000_ICR_MDDET /* Malicious Driver Detect */ +/* Extended Interrupt Mask Set */ +#define E1000_EIMS_RX_QUEUE0 E1000_EICR_RX_QUEUE0 /* Rx Queue 0 Interrupt */ +#define E1000_EIMS_RX_QUEUE1 E1000_EICR_RX_QUEUE1 /* Rx Queue 1 Interrupt */ +#define E1000_EIMS_RX_QUEUE2 E1000_EICR_RX_QUEUE2 /* Rx Queue 2 Interrupt */ +#define E1000_EIMS_RX_QUEUE3 E1000_EICR_RX_QUEUE3 /* Rx Queue 3 Interrupt */ +#define E1000_EIMS_TX_QUEUE0 E1000_EICR_TX_QUEUE0 /* Tx Queue 0 Interrupt */ +#define E1000_EIMS_TX_QUEUE1 E1000_EICR_TX_QUEUE1 /* Tx Queue 1 Interrupt */ +#define E1000_EIMS_TX_QUEUE2 E1000_EICR_TX_QUEUE2 /* Tx Queue 2 Interrupt */ +#define E1000_EIMS_TX_QUEUE3 E1000_EICR_TX_QUEUE3 /* Tx Queue 3 Interrupt */ +#define E1000_EIMS_TCP_TIMER E1000_EICR_TCP_TIMER /* TCP Timer */ +#define E1000_EIMS_OTHER E1000_EICR_OTHER /* Interrupt Cause Active */ + +/* Interrupt Cause Set */ +#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */ +#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */ +#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */ + +/* Extended Interrupt Cause Set */ +#define E1000_EICS_RX_QUEUE0 E1000_EICR_RX_QUEUE0 /* Rx Queue 0 Interrupt */ +#define E1000_EICS_RX_QUEUE1 E1000_EICR_RX_QUEUE1 /* Rx Queue 1 Interrupt */ +#define E1000_EICS_RX_QUEUE2 E1000_EICR_RX_QUEUE2 /* Rx Queue 2 Interrupt */ +#define E1000_EICS_RX_QUEUE3 E1000_EICR_RX_QUEUE3 /* Rx Queue 3 Interrupt */ +#define E1000_EICS_TX_QUEUE0 E1000_EICR_TX_QUEUE0 /* Tx Queue 0 Interrupt */ +#define E1000_EICS_TX_QUEUE1 E1000_EICR_TX_QUEUE1 /* Tx Queue 1 Interrupt */ +#define E1000_EICS_TX_QUEUE2 E1000_EICR_TX_QUEUE2 /* Tx Queue 2 Interrupt */ +#define E1000_EICS_TX_QUEUE3 E1000_EICR_TX_QUEUE3 /* Tx Queue 3 Interrupt */ +#define E1000_EICS_TCP_TIMER E1000_EICR_TCP_TIMER /* TCP Timer */ +#define E1000_EICS_OTHER E1000_EICR_OTHER /* Interrupt Cause Active */ + +#define E1000_EITR_ITR_INT_MASK 0x0000FFFF +/* E1000_EITR_CNT_IGNR is only for 82576 and newer */ +#define E1000_EITR_CNT_IGNR 0x80000000 /* Don't reset counters on write */ +#define E1000_EITR_INTERVAL 0x00007FFC + +/* Transmit Descriptor Control */ +#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */ +#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */ +#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */ +#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */ +#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */ +#define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */ +/* Enable the counting of descriptors still to be processed. */ +#define E1000_TXDCTL_COUNT_DESC 0x00400000 + +/* Flow Control Constants */ +#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001 +#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100 +#define FLOW_CONTROL_TYPE 0x8808 + +/* 802.1q VLAN Packet Size */ +#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */ +#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ + +/* Receive Address + * Number of high/low register pairs in the RAR. The RAR (Receive Address + * Registers) holds the directed and multicast addresses that we monitor. + * Technically, we have 16 spots. However, we reserve one of these spots + * (RAR[15]) for our directed address used by controllers with + * manageability enabled, allowing us room for 15 multicast addresses. + */ +#define E1000_RAR_ENTRIES 15 +#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */ +#define E1000_RAL_MAC_ADDR_LEN 4 +#define E1000_RAH_MAC_ADDR_LEN 2 +#define E1000_RAH_QUEUE_MASK_82575 0x000C0000 +#define E1000_RAH_POOL_1 0x00040000 + +/* Error Codes */ +#define E1000_SUCCESS 0 +#define E1000_ERR_NVM 1 +#define E1000_ERR_PHY 2 +#define E1000_ERR_CONFIG 3 +#define E1000_ERR_PARAM 4 +#define E1000_ERR_MAC_INIT 5 +#define E1000_ERR_PHY_TYPE 6 +#define E1000_ERR_RESET 9 +#define E1000_ERR_MASTER_REQUESTS_PENDING 10 +#define E1000_ERR_HOST_INTERFACE_COMMAND 11 +#define E1000_BLK_PHY_RESET 12 +#define E1000_ERR_SWFW_SYNC 13 +#define E1000_NOT_IMPLEMENTED 14 +#define E1000_ERR_MBX 15 +#define E1000_ERR_INVALID_ARGUMENT 16 +#define E1000_ERR_NO_SPACE 17 +#define E1000_ERR_NVM_PBA_SECTION 18 +#define E1000_ERR_I2C 19 +#define E1000_ERR_INVM_VALUE_NOT_FOUND 20 + +/* Loop limit on how long we wait for auto-negotiation to complete */ +#define FIBER_LINK_UP_LIMIT 50 +#define COPPER_LINK_UP_LIMIT 10 +#define PHY_AUTO_NEG_LIMIT 45 +#define PHY_FORCE_LIMIT 20 +/* Number of 100 microseconds we wait for PCI Express master disable */ +#define MASTER_DISABLE_TIMEOUT 800 +/* Number of milliseconds we wait for PHY configuration done after MAC reset */ +#define PHY_CFG_TIMEOUT 100 +/* Number of 2 milliseconds we wait for acquiring MDIO ownership. */ +#define MDIO_OWNERSHIP_TIMEOUT 10 +/* Number of milliseconds for NVM auto read done after MAC reset. */ +#define AUTO_READ_DONE_TIMEOUT 10 + +/* Flow Control */ +#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */ +#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */ +#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */ + +/* Transmit Configuration Word */ +#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */ +#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */ +#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */ +#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */ +#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */ + +/* Receive Configuration Word */ +#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */ +#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */ +#define E1000_RXCW_C 0x20000000 /* Receive config */ +#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */ + +#define E1000_TSYNCTXCTL_VALID 0x00000001 /* Tx timestamp valid */ +#define E1000_TSYNCTXCTL_ENABLED 0x00000010 /* enable Tx timestamping */ + +#define E1000_TSYNCRXCTL_VALID 0x00000001 /* Rx timestamp valid */ +#define E1000_TSYNCRXCTL_TYPE_MASK 0x0000000E /* Rx type mask */ +#define E1000_TSYNCRXCTL_TYPE_L2_V2 0x00 +#define E1000_TSYNCRXCTL_TYPE_L4_V1 0x02 +#define E1000_TSYNCRXCTL_TYPE_L2_L4_V2 0x04 +#define E1000_TSYNCRXCTL_TYPE_ALL 0x08 +#define E1000_TSYNCRXCTL_TYPE_EVENT_V2 0x0A +#define E1000_TSYNCRXCTL_ENABLED 0x00000010 /* enable Rx timestamping */ +#define E1000_TSYNCRXCTL_SYSCFI 0x00000020 /* Sys clock frequency */ + +#define E1000_TSYNCRXCFG_PTP_V1_CTRLT_MASK 0x000000FF +#define E1000_TSYNCRXCFG_PTP_V1_SYNC_MESSAGE 0x00 +#define E1000_TSYNCRXCFG_PTP_V1_DELAY_REQ_MESSAGE 0x01 +#define E1000_TSYNCRXCFG_PTP_V1_FOLLOWUP_MESSAGE 0x02 +#define E1000_TSYNCRXCFG_PTP_V1_DELAY_RESP_MESSAGE 0x03 +#define E1000_TSYNCRXCFG_PTP_V1_MANAGEMENT_MESSAGE 0x04 + +#define E1000_TSYNCRXCFG_PTP_V2_MSGID_MASK 0x00000F00 +#define E1000_TSYNCRXCFG_PTP_V2_SYNC_MESSAGE 0x0000 +#define E1000_TSYNCRXCFG_PTP_V2_DELAY_REQ_MESSAGE 0x0100 +#define E1000_TSYNCRXCFG_PTP_V2_PATH_DELAY_REQ_MESSAGE 0x0200 +#define E1000_TSYNCRXCFG_PTP_V2_PATH_DELAY_RESP_MESSAGE 0x0300 +#define E1000_TSYNCRXCFG_PTP_V2_FOLLOWUP_MESSAGE 0x0800 +#define E1000_TSYNCRXCFG_PTP_V2_DELAY_RESP_MESSAGE 0x0900 +#define E1000_TSYNCRXCFG_PTP_V2_PATH_DELAY_FOLLOWUP_MESSAGE 0x0A00 +#define E1000_TSYNCRXCFG_PTP_V2_ANNOUNCE_MESSAGE 0x0B00 +#define E1000_TSYNCRXCFG_PTP_V2_SIGNALLING_MESSAGE 0x0C00 +#define E1000_TSYNCRXCFG_PTP_V2_MANAGEMENT_MESSAGE 0x0D00 + +#define E1000_TIMINCA_16NS_SHIFT 24 +#define E1000_TIMINCA_INCPERIOD_SHIFT 24 +#define E1000_TIMINCA_INCVALUE_MASK 0x00FFFFFF + +#define E1000_TSICR_TXTS 0x00000002 +#define E1000_TSIM_TXTS 0x00000002 +/* TUPLE Filtering Configuration */ +#define E1000_TTQF_DISABLE_MASK 0xF0008000 /* TTQF Disable Mask */ +#define E1000_TTQF_QUEUE_ENABLE 0x100 /* TTQF Queue Enable Bit */ +#define E1000_TTQF_PROTOCOL_MASK 0xFF /* TTQF Protocol Mask */ +/* TTQF TCP Bit, shift with E1000_TTQF_PROTOCOL SHIFT */ +#define E1000_TTQF_PROTOCOL_TCP 0x0 +/* TTQF UDP Bit, shift with E1000_TTQF_PROTOCOL_SHIFT */ +#define E1000_TTQF_PROTOCOL_UDP 0x1 +/* TTQF SCTP Bit, shift with E1000_TTQF_PROTOCOL_SHIFT */ +#define E1000_TTQF_PROTOCOL_SCTP 0x2 +#define E1000_TTQF_PROTOCOL_SHIFT 5 /* TTQF Protocol Shift */ +#define E1000_TTQF_QUEUE_SHIFT 16 /* TTQF Queue Shfit */ +#define E1000_TTQF_RX_QUEUE_MASK 0x70000 /* TTQF Queue Mask */ +#define E1000_TTQF_MASK_ENABLE 0x10000000 /* TTQF Mask Enable Bit */ +#define E1000_IMIR_CLEAR_MASK 0xF001FFFF /* IMIR Reg Clear Mask */ +#define E1000_IMIR_PORT_BYPASS 0x20000 /* IMIR Port Bypass Bit */ +#define E1000_IMIR_PRIORITY_SHIFT 29 /* IMIR Priority Shift */ +#define E1000_IMIREXT_CLEAR_MASK 0x7FFFF /* IMIREXT Reg Clear Mask */ + +#define E1000_MDICNFG_EXT_MDIO 0x80000000 /* MDI ext/int destination */ +#define E1000_MDICNFG_COM_MDIO 0x40000000 /* MDI shared w/ lan 0 */ +#define E1000_MDICNFG_PHY_MASK 0x03E00000 +#define E1000_MDICNFG_PHY_SHIFT 21 + +#define E1000_MEDIA_PORT_COPPER 1 +#define E1000_MEDIA_PORT_OTHER 2 +#define E1000_M88E1112_AUTO_COPPER_SGMII 0x2 +#define E1000_M88E1112_AUTO_COPPER_BASEX 0x3 +#define E1000_M88E1112_STATUS_LINK 0x0004 /* Interface Link Bit */ +#define E1000_M88E1112_MAC_CTRL_1 0x10 +#define E1000_M88E1112_MAC_CTRL_1_MODE_MASK 0x0380 /* Mode Select */ +#define E1000_M88E1112_MAC_CTRL_1_MODE_SHIFT 7 +#define E1000_M88E1112_PAGE_ADDR 0x16 +#define E1000_M88E1112_STATUS 0x01 + +#define E1000_THSTAT_LOW_EVENT 0x20000000 /* Low thermal threshold */ +#define E1000_THSTAT_MID_EVENT 0x00200000 /* Mid thermal threshold */ +#define E1000_THSTAT_HIGH_EVENT 0x00002000 /* High thermal threshold */ +#define E1000_THSTAT_PWR_DOWN 0x00000001 /* Power Down Event */ +#define E1000_THSTAT_LINK_THROTTLE 0x00000002 /* Link Spd Throttle Event */ + +/* I350 EEE defines */ +#define E1000_IPCNFG_EEE_1G_AN 0x00000008 /* IPCNFG EEE Ena 1G AN */ +#define E1000_IPCNFG_EEE_100M_AN 0x00000004 /* IPCNFG EEE Ena 100M AN */ +#define E1000_EEER_TX_LPI_EN 0x00010000 /* EEER Tx LPI Enable */ +#define E1000_EEER_RX_LPI_EN 0x00020000 /* EEER Rx LPI Enable */ +#define E1000_EEER_LPI_FC 0x00040000 /* EEER Ena on Flow Cntrl */ +/* EEE status */ +#define E1000_EEER_EEE_NEG 0x20000000 /* EEE capability nego */ +#define E1000_EEER_RX_LPI_STATUS 0x40000000 /* Rx in LPI state */ +#define E1000_EEER_TX_LPI_STATUS 0x80000000 /* Tx in LPI state */ +#define E1000_EEE_LP_ADV_ADDR_I350 0x040F /* EEE LP Advertisement */ +#define E1000_M88E1543_PAGE_ADDR 0x16 /* Page Offset Register */ +#define E1000_M88E1543_EEE_CTRL_1 0x0 +#define E1000_M88E1543_EEE_CTRL_1_MS 0x0001 /* EEE Master/Slave */ +#define E1000_EEE_ADV_DEV_I354 7 +#define E1000_EEE_ADV_ADDR_I354 60 +#define E1000_EEE_ADV_100_SUPPORTED (1 << 1) /* 100BaseTx EEE Supported */ +#define E1000_EEE_ADV_1000_SUPPORTED (1 << 2) /* 1000BaseT EEE Supported */ +#define E1000_PCS_STATUS_DEV_I354 3 +#define E1000_PCS_STATUS_ADDR_I354 1 +#define E1000_PCS_STATUS_RX_LPI_RCVD 0x0400 +#define E1000_PCS_STATUS_TX_LPI_RCVD 0x0800 +#define E1000_EEE_SU_LPI_CLK_STP 0x00800000 /* EEE LPI Clock Stop */ +#define E1000_EEE_LP_ADV_DEV_I210 7 /* EEE LP Adv Device */ +#define E1000_EEE_LP_ADV_ADDR_I210 61 /* EEE LP Adv Register */ +/* PCI Express Control */ +#define E1000_GCR_RXD_NO_SNOOP 0x00000001 +#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002 +#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004 +#define E1000_GCR_TXD_NO_SNOOP 0x00000008 +#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010 +#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020 +#define E1000_GCR_CMPL_TMOUT_MASK 0x0000F000 +#define E1000_GCR_CMPL_TMOUT_10ms 0x00001000 +#define E1000_GCR_CMPL_TMOUT_RESEND 0x00010000 +#define E1000_GCR_CAP_VER2 0x00040000 + +#define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \ + E1000_GCR_RXDSCW_NO_SNOOP | \ + E1000_GCR_RXDSCR_NO_SNOOP | \ + E1000_GCR_TXD_NO_SNOOP | \ + E1000_GCR_TXDSCW_NO_SNOOP | \ + E1000_GCR_TXDSCR_NO_SNOOP) + +#define E1000_MMDAC_FUNC_DATA 0x4000 /* Data, no post increment */ + +/* mPHY address control and data registers */ +#define E1000_MPHY_ADDR_CTL 0x0024 /* Address Control Reg */ +#define E1000_MPHY_ADDR_CTL_OFFSET_MASK 0xFFFF0000 +#define E1000_MPHY_DATA 0x0E10 /* Data Register */ + +/* AFE CSR Offset for PCS CLK */ +#define E1000_MPHY_PCS_CLK_REG_OFFSET 0x0004 +/* Override for near end digital loopback. */ +#define E1000_MPHY_PCS_CLK_REG_DIGINELBEN 0x10 + +/* PHY Control Register */ +#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */ +#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */ +#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ +#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ +#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */ +#define MII_CR_POWER_DOWN 0x0800 /* Power down */ +#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */ +#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */ +#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */ +#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */ +#define MII_CR_SPEED_1000 0x0040 +#define MII_CR_SPEED_100 0x2000 +#define MII_CR_SPEED_10 0x0000 + +/* PHY Status Register */ +#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */ +#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */ +#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */ +#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */ +#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */ +#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */ +#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */ +#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */ +#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */ +#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */ +#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */ +#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */ +#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */ +#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */ +#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */ + +/* Autoneg Advertisement Register */ +#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */ +#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */ +#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */ +#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */ +#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */ +#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */ +#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */ +#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */ +#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */ +#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */ + +/* Link Partner Ability Register (Base Page) */ +#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */ +#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP 10T Half Dplx Capable */ +#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP 10T Full Dplx Capable */ +#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP 100TX Half Dplx Capable */ +#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP 100TX Full Dplx Capable */ +#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */ +#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */ +#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asym Pause Direction bit */ +#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP detected Remote Fault */ +#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP rx'd link code word */ +#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */ + +/* Autoneg Expansion Register */ +#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */ +#define NWAY_ER_PAGE_RXD 0x0002 /* LP 10T Half Dplx Capable */ +#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP 10T Full Dplx Capable */ +#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP 100TX Half Dplx Capable */ +#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP 100TX Full Dplx Capable */ + +/* 1000BASE-T Control Register */ +#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */ +#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */ +#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */ +/* 1=Repeater/switch device port 0=DTE device */ +#define CR_1000T_REPEATER_DTE 0x0400 +/* 1=Configure PHY as Master 0=Configure PHY as Slave */ +#define CR_1000T_MS_VALUE 0x0800 +/* 1=Master/Slave manual config value 0=Automatic Master/Slave config */ +#define CR_1000T_MS_ENABLE 0x1000 +#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */ +#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */ +#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */ +#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */ +#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */ + +/* 1000BASE-T Status Register */ +#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle err since last rd */ +#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asym pause direction bit */ +#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */ +#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */ +#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */ +#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */ +#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local Tx Master, 0=Slave */ +#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */ + +#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5 + +/* PHY 1000 MII Register/Bit Definitions */ +/* PHY Registers defined by IEEE */ +#define PHY_CONTROL 0x00 /* Control Register */ +#define PHY_STATUS 0x01 /* Status Register */ +#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */ +#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */ +#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */ +#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */ +#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */ +#define PHY_NEXT_PAGE_TX 0x07 /* Next Page Tx */ +#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */ +#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */ +#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */ +#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */ + +#define PHY_CONTROL_LB 0x4000 /* PHY Loopback bit */ + +/* NVM Control */ +#define E1000_EECD_SK 0x00000001 /* NVM Clock */ +#define E1000_EECD_CS 0x00000002 /* NVM Chip Select */ +#define E1000_EECD_DI 0x00000004 /* NVM Data In */ +#define E1000_EECD_DO 0x00000008 /* NVM Data Out */ +#define E1000_EECD_REQ 0x00000040 /* NVM Access Request */ +#define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */ +#define E1000_EECD_PRES 0x00000100 /* NVM Present */ +#define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */ +#define E1000_EECD_BLOCKED 0x00008000 /* Bit banging access blocked flag */ +#define E1000_EECD_ABORT 0x00010000 /* NVM operation aborted flag */ +#define E1000_EECD_TIMEOUT 0x00020000 /* NVM read operation timeout flag */ +#define E1000_EECD_ERROR_CLR 0x00040000 /* NVM error status clear bit */ +/* NVM Addressing bits based on type 0=small, 1=large */ +#define E1000_EECD_ADDR_BITS 0x00000400 +#define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */ +#define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */ +#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */ +#define E1000_EECD_SIZE_EX_SHIFT 11 +#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */ +#define E1000_EECD_AUPDEN 0x00100000 /* Ena Auto FLASH update */ +#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */ +#define E1000_EECD_SEC1VAL_VALID_MASK (E1000_EECD_AUTO_RD | E1000_EECD_PRES) +#define E1000_EECD_FLUPD_I210 0x00800000 /* Update FLASH */ +#define E1000_EECD_FLUDONE_I210 0x04000000 /* Update FLASH done */ +#define E1000_EECD_FLASH_DETECTED_I210 0x00080000 /* FLASH detected */ +#define E1000_EECD_SEC1VAL_I210 0x02000000 /* Sector One Valid */ +#define E1000_FLUDONE_ATTEMPTS 20000 +#define E1000_EERD_EEWR_MAX_COUNT 512 /* buffered EEPROM words rw */ +#define E1000_I210_FIFO_SEL_RX 0x00 +#define E1000_I210_FIFO_SEL_TX_QAV(_i) (0x02 + (_i)) +#define E1000_I210_FIFO_SEL_TX_LEGACY E1000_I210_FIFO_SEL_TX_QAV(0) +#define E1000_I210_FIFO_SEL_BMC2OS_TX 0x06 +#define E1000_I210_FIFO_SEL_BMC2OS_RX 0x01 + +#define E1000_I210_FLASH_SECTOR_SIZE 0x1000 /* 4KB FLASH sector unit size */ +/* Secure FLASH mode requires removing MSb */ +#define E1000_I210_FW_PTR_MASK 0x7FFF +/* Firmware code revision field word offset*/ +#define E1000_I210_FW_VER_OFFSET 328 + +#define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM read/write regs */ +#define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */ +#define E1000_NVM_RW_REG_START 1 /* Start operation */ +#define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */ +#define E1000_NVM_POLL_WRITE 1 /* Flag for polling for write complete */ +#define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */ +#define E1000_FLASH_UPDATES 2000 + +/* NVM Word Offsets */ +#define NVM_COMPAT 0x0003 +#define NVM_ID_LED_SETTINGS 0x0004 +#define NVM_VERSION 0x0005 +#define E1000_I210_NVM_FW_MODULE_PTR 0x0010 +#define E1000_I350_NVM_FW_MODULE_PTR 0x0051 +#define NVM_FUTURE_INIT_WORD1 0x0019 +#define NVM_ETRACK_WORD 0x0042 +#define NVM_ETRACK_HIWORD 0x0043 +#define NVM_COMB_VER_OFF 0x0083 +#define NVM_COMB_VER_PTR 0x003d + +/* NVM version defines */ +#define NVM_MAJOR_MASK 0xF000 +#define NVM_MINOR_MASK 0x0FF0 +#define NVM_IMAGE_ID_MASK 0x000F +#define NVM_COMB_VER_MASK 0x00FF +#define NVM_MAJOR_SHIFT 12 +#define NVM_MINOR_SHIFT 4 +#define NVM_COMB_VER_SHFT 8 +#define NVM_VER_INVALID 0xFFFF +#define NVM_ETRACK_SHIFT 16 +#define NVM_ETRACK_VALID 0x8000 +#define NVM_NEW_DEC_MASK 0x0F00 +#define NVM_HEX_CONV 16 +#define NVM_HEX_TENS 10 + +/* FW version defines */ +/* Offset of "Loader patch ptr" in Firmware Header */ +#define E1000_I350_NVM_FW_LOADER_PATCH_PTR_OFFSET 0x01 +/* Patch generation hour & minutes */ +#define E1000_I350_NVM_FW_VER_WORD1_OFFSET 0x04 +/* Patch generation month & day */ +#define E1000_I350_NVM_FW_VER_WORD2_OFFSET 0x05 +/* Patch generation year */ +#define E1000_I350_NVM_FW_VER_WORD3_OFFSET 0x06 +/* Patch major & minor numbers */ +#define E1000_I350_NVM_FW_VER_WORD4_OFFSET 0x07 + +#define NVM_MAC_ADDR 0x0000 +#define NVM_SUB_DEV_ID 0x000B +#define NVM_SUB_VEN_ID 0x000C +#define NVM_DEV_ID 0x000D +#define NVM_VEN_ID 0x000E +#define NVM_INIT_CTRL_2 0x000F +#define NVM_INIT_CTRL_4 0x0013 +#define NVM_LED_1_CFG 0x001C +#define NVM_LED_0_2_CFG 0x001F + +#define NVM_COMPAT_VALID_CSUM 0x0001 +#define NVM_FUTURE_INIT_WORD1_VALID_CSUM 0x0040 + +#define NVM_ETS_CFG 0x003E +#define NVM_ETS_LTHRES_DELTA_MASK 0x07C0 +#define NVM_ETS_LTHRES_DELTA_SHIFT 6 +#define NVM_ETS_TYPE_MASK 0x0038 +#define NVM_ETS_TYPE_SHIFT 3 +#define NVM_ETS_TYPE_EMC 0x000 +#define NVM_ETS_NUM_SENSORS_MASK 0x0007 +#define NVM_ETS_DATA_LOC_MASK 0x3C00 +#define NVM_ETS_DATA_LOC_SHIFT 10 +#define NVM_ETS_DATA_INDEX_MASK 0x0300 +#define NVM_ETS_DATA_INDEX_SHIFT 8 +#define NVM_ETS_DATA_HTHRESH_MASK 0x00FF +#define NVM_INIT_CONTROL2_REG 0x000F +#define NVM_INIT_CONTROL3_PORT_B 0x0014 +#define NVM_INIT_3GIO_3 0x001A +#define NVM_SWDEF_PINS_CTRL_PORT_0 0x0020 +#define NVM_INIT_CONTROL3_PORT_A 0x0024 +#define NVM_CFG 0x0012 +#define NVM_ALT_MAC_ADDR_PTR 0x0037 +#define NVM_CHECKSUM_REG 0x003F +#define NVM_COMPATIBILITY_REG_3 0x0003 +#define NVM_COMPATIBILITY_BIT_MASK 0x8000 + +#define E1000_NVM_CFG_DONE_PORT_0 0x040000 /* MNG config cycle done */ +#define E1000_NVM_CFG_DONE_PORT_1 0x080000 /* ...for second port */ +#define E1000_NVM_CFG_DONE_PORT_2 0x100000 /* ...for third port */ +#define E1000_NVM_CFG_DONE_PORT_3 0x200000 /* ...for fourth port */ + +#define NVM_82580_LAN_FUNC_OFFSET(a) ((a) ? (0x40 + (0x40 * (a))) : 0) + +/* Mask bits for fields in Word 0x24 of the NVM */ +#define NVM_WORD24_COM_MDIO 0x0008 /* MDIO interface shared */ +#define NVM_WORD24_EXT_MDIO 0x0004 /* MDIO accesses routed extrnl */ +/* Offset of Link Mode bits for 82575/82576 */ +#define NVM_WORD24_LNK_MODE_OFFSET 8 +/* Offset of Link Mode bits for 82580 up */ +#define NVM_WORD24_82580_LNK_MODE_OFFSET 4 + + +/* Mask bits for fields in Word 0x0f of the NVM */ +#define NVM_WORD0F_PAUSE_MASK 0x3000 +#define NVM_WORD0F_PAUSE 0x1000 +#define NVM_WORD0F_ASM_DIR 0x2000 + +/* Mask bits for fields in Word 0x1a of the NVM */ +#define NVM_WORD1A_ASPM_MASK 0x000C + +/* Mask bits for fields in Word 0x03 of the EEPROM */ +#define NVM_COMPAT_LOM 0x0800 + +/* length of string needed to store PBA number */ +#define E1000_PBANUM_LENGTH 11 + +/* For checksumming, the sum of all words in the NVM should equal 0xBABA. */ +#define NVM_SUM 0xBABA + +/* PBA (printed board assembly) number words */ +#define NVM_PBA_OFFSET_0 8 +#define NVM_PBA_OFFSET_1 9 +#define NVM_PBA_PTR_GUARD 0xFAFA +#define NVM_RESERVED_WORD 0xFFFF +#define NVM_WORD_SIZE_BASE_SHIFT 6 + +/* NVM Commands - SPI */ +#define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */ +#define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */ +#define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */ +#define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */ +#define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */ +#define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */ + +/* SPI NVM Status Register */ +#define NVM_STATUS_RDY_SPI 0x01 + +/* Word definitions for ID LED Settings */ +#define ID_LED_RESERVED_0000 0x0000 +#define ID_LED_RESERVED_FFFF 0xFFFF +#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \ + (ID_LED_OFF1_OFF2 << 8) | \ + (ID_LED_DEF1_DEF2 << 4) | \ + (ID_LED_DEF1_DEF2)) +#define ID_LED_DEF1_DEF2 0x1 +#define ID_LED_DEF1_ON2 0x2 +#define ID_LED_DEF1_OFF2 0x3 +#define ID_LED_ON1_DEF2 0x4 +#define ID_LED_ON1_ON2 0x5 +#define ID_LED_ON1_OFF2 0x6 +#define ID_LED_OFF1_DEF2 0x7 +#define ID_LED_OFF1_ON2 0x8 +#define ID_LED_OFF1_OFF2 0x9 + +#define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF +#define IGP_ACTIVITY_LED_ENABLE 0x0300 +#define IGP_LED3_MODE 0x07000000 + +/* PCI/PCI-X/PCI-EX Config space */ +#define PCI_HEADER_TYPE_REGISTER 0x0E +#define PCIE_LINK_STATUS 0x12 +#define PCIE_DEVICE_CONTROL2 0x28 + +#define PCI_HEADER_TYPE_MULTIFUNC 0x80 +#define PCIE_LINK_WIDTH_MASK 0x3F0 +#define PCIE_LINK_WIDTH_SHIFT 4 +#define PCIE_LINK_SPEED_MASK 0x0F +#define PCIE_LINK_SPEED_2500 0x01 +#define PCIE_LINK_SPEED_5000 0x02 +#define PCIE_DEVICE_CONTROL2_16ms 0x0005 + +#ifndef ETH_ADDR_LEN +#define ETH_ADDR_LEN 6 +#endif + +#define PHY_REVISION_MASK 0xFFFFFFF0 +#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */ +#define MAX_PHY_MULTI_PAGE_REG 0xF + +/* Bit definitions for valid PHY IDs. + * I = Integrated + * E = External + */ +#define M88E1000_E_PHY_ID 0x01410C50 +#define M88E1000_I_PHY_ID 0x01410C30 +#define M88E1011_I_PHY_ID 0x01410C20 +#define IGP01E1000_I_PHY_ID 0x02A80380 +#define M88E1111_I_PHY_ID 0x01410CC0 +#define M88E1543_E_PHY_ID 0x01410EA0 +#define M88E1112_E_PHY_ID 0x01410C90 +#define I347AT4_E_PHY_ID 0x01410DC0 +#define M88E1340M_E_PHY_ID 0x01410DF0 +#define GG82563_E_PHY_ID 0x01410CA0 +#define IGP03E1000_E_PHY_ID 0x02A80390 +#define IFE_E_PHY_ID 0x02A80330 +#define IFE_PLUS_E_PHY_ID 0x02A80320 +#define IFE_C_E_PHY_ID 0x02A80310 +#define I82580_I_PHY_ID 0x015403A0 +#define I350_I_PHY_ID 0x015403B0 +#define I210_I_PHY_ID 0x01410C00 +#define IGP04E1000_E_PHY_ID 0x02A80391 +#define M88_VENDOR 0x0141 + +/* M88E1000 Specific Registers */ +#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Reg */ +#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Reg */ +#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Cntrl */ +#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */ + +#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for pg number setting */ +#define M88E1000_PHY_GEN_CONTROL 0x1E /* meaning depends on reg 29 */ + +/* M88E1000 PHY Specific Control Register */ +#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reverse enabled */ +/* MDI Crossover Mode bits 6:5 Manual MDI configuration */ +#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 +#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */ +/* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */ +#define M88E1000_PSCR_AUTO_X_1000T 0x0040 +/* Auto crossover enabled all speeds */ +#define M88E1000_PSCR_AUTO_X_MODE 0x0060 +#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Tx */ + +/* M88E1000 PHY Specific Status Register */ +#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */ +#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */ +#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */ +/* 0 = <50M + * 1 = 50-80M + * 2 = 80-110M + * 3 = 110-140M + * 4 = >140M + */ +#define M88E1000_PSSR_CABLE_LENGTH 0x0380 +#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */ +#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */ +#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */ +#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */ + +#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7 + +/* Number of times we will attempt to autonegotiate before downshifting if we + * are the master + */ +#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00 +#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000 +/* Number of times we will attempt to autonegotiate before downshifting if we + * are the slave + */ +#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300 +#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100 +#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */ + +/* Intel I347AT4 Registers */ +#define I347AT4_PCDL 0x10 /* PHY Cable Diagnostics Length */ +#define I347AT4_PCDC 0x15 /* PHY Cable Diagnostics Control */ +#define I347AT4_PAGE_SELECT 0x16 + +/* I347AT4 Extended PHY Specific Control Register */ + +/* Number of times we will attempt to autonegotiate before downshifting if we + * are the master + */ +#define I347AT4_PSCR_DOWNSHIFT_ENABLE 0x0800 +#define I347AT4_PSCR_DOWNSHIFT_MASK 0x7000 +#define I347AT4_PSCR_DOWNSHIFT_1X 0x0000 +#define I347AT4_PSCR_DOWNSHIFT_2X 0x1000 +#define I347AT4_PSCR_DOWNSHIFT_3X 0x2000 +#define I347AT4_PSCR_DOWNSHIFT_4X 0x3000 +#define I347AT4_PSCR_DOWNSHIFT_5X 0x4000 +#define I347AT4_PSCR_DOWNSHIFT_6X 0x5000 +#define I347AT4_PSCR_DOWNSHIFT_7X 0x6000 +#define I347AT4_PSCR_DOWNSHIFT_8X 0x7000 + +/* I347AT4 PHY Cable Diagnostics Control */ +#define I347AT4_PCDC_CABLE_LENGTH_UNIT 0x0400 /* 0=cm 1=meters */ + +/* M88E1112 only registers */ +#define M88E1112_VCT_DSP_DISTANCE 0x001A + +/* M88EC018 Rev 2 specific DownShift settings */ +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800 + +/* Bits... + * 15-5: page + * 4-0: register offset + */ +#define GG82563_PAGE_SHIFT 5 +#define GG82563_REG(page, reg) \ + (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) +#define GG82563_MIN_ALT_REG 30 + +/* GG82563 Specific Registers */ +#define GG82563_PHY_SPEC_CTRL GG82563_REG(0, 16) /* PHY Spec Cntrl */ +#define GG82563_PHY_PAGE_SELECT GG82563_REG(0, 22) /* Page Select */ +#define GG82563_PHY_SPEC_CTRL_2 GG82563_REG(0, 26) /* PHY Spec Cntrl2 */ +#define GG82563_PHY_PAGE_SELECT_ALT GG82563_REG(0, 29) /* Alt Page Select */ + +/* MAC Specific Control Register */ +#define GG82563_PHY_MAC_SPEC_CTRL GG82563_REG(2, 21) + +#define GG82563_PHY_DSP_DISTANCE GG82563_REG(5, 26) /* DSP Distance */ + +/* Page 193 - Port Control Registers */ +/* Kumeran Mode Control */ +#define GG82563_PHY_KMRN_MODE_CTRL GG82563_REG(193, 16) +#define GG82563_PHY_PWR_MGMT_CTRL GG82563_REG(193, 20) /* Pwr Mgt Ctrl */ + +/* Page 194 - KMRN Registers */ +#define GG82563_PHY_INBAND_CTRL GG82563_REG(194, 18) /* Inband Ctrl */ + +/* MDI Control */ +#define E1000_MDIC_REG_MASK 0x001F0000 +#define E1000_MDIC_REG_SHIFT 16 +#define E1000_MDIC_PHY_MASK 0x03E00000 +#define E1000_MDIC_PHY_SHIFT 21 +#define E1000_MDIC_OP_WRITE 0x04000000 +#define E1000_MDIC_OP_READ 0x08000000 +#define E1000_MDIC_READY 0x10000000 +#define E1000_MDIC_ERROR 0x40000000 +#define E1000_MDIC_DEST 0x80000000 + +/* SerDes Control */ +#define E1000_GEN_CTL_READY 0x80000000 +#define E1000_GEN_CTL_ADDRESS_SHIFT 8 +#define E1000_GEN_POLL_TIMEOUT 640 + +/* LinkSec register fields */ +#define E1000_LSECTXCAP_SUM_MASK 0x00FF0000 +#define E1000_LSECTXCAP_SUM_SHIFT 16 +#define E1000_LSECRXCAP_SUM_MASK 0x00FF0000 +#define E1000_LSECRXCAP_SUM_SHIFT 16 + +#define E1000_LSECTXCTRL_EN_MASK 0x00000003 +#define E1000_LSECTXCTRL_DISABLE 0x0 +#define E1000_LSECTXCTRL_AUTH 0x1 +#define E1000_LSECTXCTRL_AUTH_ENCRYPT 0x2 +#define E1000_LSECTXCTRL_AISCI 0x00000020 +#define E1000_LSECTXCTRL_PNTHRSH_MASK 0xFFFFFF00 +#define E1000_LSECTXCTRL_RSV_MASK 0x000000D8 + +#define E1000_LSECRXCTRL_EN_MASK 0x0000000C +#define E1000_LSECRXCTRL_EN_SHIFT 2 +#define E1000_LSECRXCTRL_DISABLE 0x0 +#define E1000_LSECRXCTRL_CHECK 0x1 +#define E1000_LSECRXCTRL_STRICT 0x2 +#define E1000_LSECRXCTRL_DROP 0x3 +#define E1000_LSECRXCTRL_PLSH 0x00000040 +#define E1000_LSECRXCTRL_RP 0x00000080 +#define E1000_LSECRXCTRL_RSV_MASK 0xFFFFFF33 + +/* Tx Rate-Scheduler Config fields */ +#define E1000_RTTBCNRC_RS_ENA 0x80000000 +#define E1000_RTTBCNRC_RF_DEC_MASK 0x00003FFF +#define E1000_RTTBCNRC_RF_INT_SHIFT 14 +#define E1000_RTTBCNRC_RF_INT_MASK \ + (E1000_RTTBCNRC_RF_DEC_MASK << E1000_RTTBCNRC_RF_INT_SHIFT) + +/* DMA Coalescing register fields */ +/* DMA Coalescing Watchdog Timer */ +#define E1000_DMACR_DMACWT_MASK 0x00003FFF +/* DMA Coalescing Rx Threshold */ +#define E1000_DMACR_DMACTHR_MASK 0x00FF0000 +#define E1000_DMACR_DMACTHR_SHIFT 16 +/* Lx when no PCIe transactions */ +#define E1000_DMACR_DMAC_LX_MASK 0x30000000 +#define E1000_DMACR_DMAC_LX_SHIFT 28 +#define E1000_DMACR_DMAC_EN 0x80000000 /* Enable DMA Coalescing */ +/* DMA Coalescing BMC-to-OS Watchdog Enable */ +#define E1000_DMACR_DC_BMC2OSW_EN 0x00008000 + +/* DMA Coalescing Transmit Threshold */ +#define E1000_DMCTXTH_DMCTTHR_MASK 0x00000FFF + +#define E1000_DMCTLX_TTLX_MASK 0x00000FFF /* Time to LX request */ + +/* Rx Traffic Rate Threshold */ +#define E1000_DMCRTRH_UTRESH_MASK 0x0007FFFF +/* Rx packet rate in current window */ +#define E1000_DMCRTRH_LRPRCW 0x80000000 + +/* DMA Coal Rx Traffic Current Count */ +#define E1000_DMCCNT_CCOUNT_MASK 0x01FFFFFF + +/* Flow ctrl Rx Threshold High val */ +#define E1000_FCRTC_RTH_COAL_MASK 0x0003FFF0 +#define E1000_FCRTC_RTH_COAL_SHIFT 4 +/* Lx power decision based on DMA coal */ +#define E1000_PCIEMISC_LX_DECISION 0x00000080 + +#define E1000_RXPBS_CFG_TS_EN 0x80000000 /* Timestamp in Rx buffer */ +#define E1000_RXPBS_SIZE_I210_MASK 0x0000003F /* Rx packet buffer size */ +#define E1000_TXPB0S_SIZE_I210_MASK 0x0000003F /* Tx packet buffer 0 size */ + +/* Proxy Filter Control */ +#define E1000_PROXYFC_D0 0x00000001 /* Enable offload in D0 */ +#define E1000_PROXYFC_EX 0x00000004 /* Directed exact proxy */ +#define E1000_PROXYFC_MC 0x00000008 /* Directed MC Proxy */ +#define E1000_PROXYFC_BC 0x00000010 /* Broadcast Proxy Enable */ +#define E1000_PROXYFC_ARP_DIRECTED 0x00000020 /* Directed ARP Proxy Ena */ +#define E1000_PROXYFC_IPV4 0x00000040 /* Directed IPv4 Enable */ +#define E1000_PROXYFC_IPV6 0x00000080 /* Directed IPv6 Enable */ +#define E1000_PROXYFC_NS 0x00000200 /* IPv6 Neighbor Solicitation */ +#define E1000_PROXYFC_ARP 0x00000800 /* ARP Request Proxy Ena */ +/* Proxy Status */ +#define E1000_PROXYS_CLEAR 0xFFFFFFFF /* Clear */ + +/* Firmware Status */ +#define E1000_FWSTS_FWRI 0x80000000 /* FW Reset Indication */ +/* VF Control */ +#define E1000_VTCTRL_RST 0x04000000 /* Reset VF */ + +#define E1000_STATUS_LAN_ID_MASK 0x00000000C /* Mask for Lan ID field */ +/* Lan ID bit field offset in status register */ +#define E1000_STATUS_LAN_ID_OFFSET 2 +#define E1000_VFTA_ENTRIES 128 +#ifndef E1000_UNUSEDARG +#define E1000_UNUSEDARG +#endif /* E1000_UNUSEDARG */ +#endif /* _E1000_DEFINES_H_ */ |