diff options
Diffstat (limited to 'src/dpdk_lib18/librte_pmd_bond/rte_eth_bond.h')
| -rwxr-xr-x | src/dpdk_lib18/librte_pmd_bond/rte_eth_bond.h | 359 |
1 files changed, 359 insertions, 0 deletions
diff --git a/src/dpdk_lib18/librte_pmd_bond/rte_eth_bond.h b/src/dpdk_lib18/librte_pmd_bond/rte_eth_bond.h new file mode 100755 index 00000000..71779831 --- /dev/null +++ b/src/dpdk_lib18/librte_pmd_bond/rte_eth_bond.h @@ -0,0 +1,359 @@ +/*- + * BSD LICENSE + * + * Copyright(c) 2010-2014 Intel Corporation. All rights reserved. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Intel Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +#ifndef _RTE_ETH_BOND_H_ +#define _RTE_ETH_BOND_H_ + +/** + * @file rte_eth_bond.h + * + * RTE Link Bonding Ethernet Device + * Link Bonding for 1GbE and 10GbE ports to allow the aggregation of multiple + * (slave) NICs into a single logical interface. The bonded device processes + * these interfaces based on the mode of operation specified and supported. + * This implementation supports 4 modes of operation round robin, active backup + * balance and broadcast. Providing redundant links, fault tolerance and/or + * load balancing of network ports + */ + +#ifdef __cplusplus +extern "C" { +#endif + +#include <rte_ether.h> + +/* Supported modes of operation of link bonding library */ + +#define BONDING_MODE_ROUND_ROBIN (0) +/**< Round Robin (Mode 0). + * In this mode all transmitted packets will be balanced equally across all + * active slaves of the bonded in a round robin fashion. */ +#define BONDING_MODE_ACTIVE_BACKUP (1) +/**< Active Backup (Mode 1). + * In this mode all packets transmitted will be transmitted on the primary + * slave until such point as the primary slave is no longer available and then + * transmitted packets will be sent on the next available slaves. The primary + * slave can be defined by the user but defaults to the first active slave + * available if not specified. */ +#define BONDING_MODE_BALANCE (2) +/**< Balance (Mode 2). + * In this mode all packets transmitted will be balanced across the available + * slaves using one of three available transmit policies - l2, l2+3 or l3+4. + * See BALANCE_XMIT_POLICY macros definitions for further details on transmit + * policies. */ +#ifdef RTE_MBUF_REFCNT +#define BONDING_MODE_BROADCAST (3) +/**< Broadcast (Mode 3). + * In this mode all transmitted packets will be transmitted on all available + * active slaves of the bonded. */ +#endif +#define BONDING_MODE_8023AD (4) +/**< 802.3AD (Mode 4). + * + * This mode provides auto negotiation/configuration + * of peers and well as link status changes monitoring using out of band + * LACP (link aggregation control protocol) messages. For further details of + * LACP specification see the IEEE 802.3ad/802.1AX standards. It is also + * described here + * https://www.kernel.org/doc/Documentation/networking/bonding.txt. + * + * Important Usage Notes: + * - for LACP mode to work the rx/tx burst functions must be invoked + * at least once every 100ms, otherwise the out-of-band LACP messages will not + * be handled with the expected latency and this may cause the link status to be + * incorrectly marked as down or failure to correctly negotiate with peers. + * - For optimal performance during initial handshaking the array of mbufs provided + * to rx_burst should be at least 2 times the slave count size. + * + */ +#define BONDING_MODE_ADAPTIVE_TRANSMIT_LOAD_BALANCING (5) +/**< Adaptive TLB (Mode 5) + * This mode provides an adaptive transmit load balancing. It dynamically + * changes the transmitting slave, according to the computed load. Statistics + * are collected in 100ms intervals and scheduled every 10ms */ + +/* Balance Mode Transmit Policies */ +#define BALANCE_XMIT_POLICY_LAYER2 (0) +/**< Layer 2 (Ethernet MAC) */ +#define BALANCE_XMIT_POLICY_LAYER23 (1) +/**< Layer 2+3 (Ethernet MAC + IP Addresses) transmit load balancing */ +#define BALANCE_XMIT_POLICY_LAYER34 (2) +/**< Layer 3+4 (IP Addresses + UDP Ports) transmit load balancing */ + +/** + * Create a bonded rte_eth_dev device + * + * @param name Name of new link bonding device. + * @param mode Mode to initialize bonding device in. + * @param socket_id Socket Id on which to allocate eth_dev resources. + * + * @return + * Port Id of created rte_eth_dev on success, negative value otherwise + */ +int +rte_eth_bond_create(const char *name, uint8_t mode, uint8_t socket_id); + +/** + * Add a rte_eth_dev device as a slave to the bonded device + * + * @param bonded_port_id Port ID of bonded device. + * @param slave_port_id Port ID of slave device. + * + * @return + * 0 on success, negative value otherwise + */ +int +rte_eth_bond_slave_add(uint8_t bonded_port_id, uint8_t slave_port_id); + +/** + * Remove a slave rte_eth_dev device from the bonded device + * + * @param bonded_port_id Port ID of bonded device. + * @param slave_port_id Port ID of slave device. + * + * @return + * 0 on success, negative value otherwise + */ +int +rte_eth_bond_slave_remove(uint8_t bonded_port_id, uint8_t slave_port_id); + +/** + * Set link bonding mode of bonded device + * + * @param bonded_port_id Port ID of bonded device. + * @param mode Bonding mode to set + * + * @return + * 0 on success, negative value otherwise + */ +int +rte_eth_bond_mode_set(uint8_t bonded_port_id, uint8_t mode); + +/** + * Get link bonding mode of bonded device + * + * @param bonded_port_id Port ID of bonded device. + * + * @return + * link bonding mode on success, negative value otherwise + */ +int +rte_eth_bond_mode_get(uint8_t bonded_port_id); + +/** + * Set slave rte_eth_dev as primary slave of bonded device + * + * @param bonded_port_id Port ID of bonded device. + * @param slave_port_id Port ID of slave device. + * + * @return + * 0 on success, negative value otherwise + */ +int +rte_eth_bond_primary_set(uint8_t bonded_port_id, uint8_t slave_port_id); + +/** + * Get primary slave of bonded device + * + * @param bonded_port_id Port ID of bonded device. + * + * @return + * Port Id of primary slave on success, -1 on failure + */ +int +rte_eth_bond_primary_get(uint8_t bonded_port_id); + +/** + * Populate an array with list of the slaves port id's of the bonded device + * + * @param bonded_port_id Port ID of bonded eth_dev to interrogate + * @param slaves Array to be populated with the current active slaves + * @param len Length of slaves array + * + * @return + * Number of slaves associated with bonded device on success, + * negative value otherwise + */ +int +rte_eth_bond_slaves_get(uint8_t bonded_port_id, uint8_t slaves[], uint8_t len); + +/** + * Populate an array with list of the active slaves port id's of the bonded + * device. + * + * @param bonded_port_id Port ID of bonded eth_dev to interrogate + * @param slaves Array to be populated with the current active slaves + * @param len Length of slaves array + * + * @return + * Number of active slaves associated with bonded device on success, + * negative value otherwise + */ +int +rte_eth_bond_active_slaves_get(uint8_t bonded_port_id, uint8_t slaves[], + uint8_t len); + +/** + * Set explicit MAC address to use on bonded device and it's slaves. + * + * @param bonded_port_id Port ID of bonded device. + * @param mac_addr MAC Address to use on bonded device overriding + * slaves MAC addresses + * + * @return + * 0 on success, negative value otherwise + */ +int +rte_eth_bond_mac_address_set(uint8_t bonded_port_id, + struct ether_addr *mac_addr); + +/** + * Reset bonded device to use MAC from primary slave on bonded device and it's + * slaves. + * + * @param bonded_port_id Port ID of bonded device. + * + * @return + * 0 on success, negative value otherwise + */ +int +rte_eth_bond_mac_address_reset(uint8_t bonded_port_id); + +/** + * Set the transmit policy for bonded device to use when it is operating in + * balance mode, this parameter is otherwise ignored in other modes of + * operation. + * + * @param bonded_port_id Port ID of bonded device. + * @param policy Balance mode transmission policy. + * + * @return + * 0 on success, negative value otherwise. + */ +int +rte_eth_bond_xmit_policy_set(uint8_t bonded_port_id, uint8_t policy); + +/** + * Get the transmit policy set on bonded device for balance mode operation + * + * @param bonded_port_id Port ID of bonded device. + * + * @return + * Balance transmit policy on success, negative value otherwise. + */ +int +rte_eth_bond_xmit_policy_get(uint8_t bonded_port_id); + +/** + * Set the link monitoring frequency (in ms) for monitoring the link status of + * slave devices + * + * @param bonded_port_id Port ID of bonded device. + * @param internal_ms Monitoring interval in milliseconds + * + * @return + * 0 on success, negative value otherwise. + */ + +int +rte_eth_bond_link_monitoring_set(uint8_t bonded_port_id, uint32_t internal_ms); + +/** + * Get the current link monitoring frequency (in ms) for monitoring of the link + * status of slave devices + * + * @param bonded_port_id Port ID of bonded device. + * + * @return + * Monitoring interval on success, negative value otherwise. + */ +int +rte_eth_bond_link_monitoring_get(uint8_t bonded_port_id); + + +/** + * Set the period in milliseconds for delaying the disabling of a bonded link + * when the link down status has been detected + * + * @param bonded_port_id Port ID of bonded device. + * @param delay_ms Delay period in milliseconds. + * + * @return + * 0 on success, negative value otherwise. + */ +int +rte_eth_bond_link_down_prop_delay_set(uint8_t bonded_port_id, uint32_t delay_ms); + +/** + * Get the period in milliseconds set for delaying the disabling of a bonded + * link when the link down status has been detected + * + * @param bonded_port_id Port ID of bonded device. + * + * @return + * Delay period on success, negative value otherwise. + */ +int +rte_eth_bond_link_down_prop_delay_get(uint8_t bonded_port_id); + +/** + * Set the period in milliseconds for delaying the enabling of a bonded link + * when the link up status has been detected + * + * @param bonded_port_id Port ID of bonded device. + * @param delay_ms Delay period in milliseconds. + * + * @return + * 0 on success, negative value otherwise. + */ +int +rte_eth_bond_link_up_prop_delay_set(uint8_t bonded_port_id, uint32_t delay_ms); + +/** + * Get the period in milliseconds set for delaying the enabling of a bonded + * link when the link up status has been detected + * + * @param bonded_port_id Port ID of bonded device. + * + * @return + * Delay period on success, negative value otherwise. + */ +int +rte_eth_bond_link_up_prop_delay_get(uint8_t bonded_port_id); + + +#ifdef __cplusplus +} +#endif + +#endif |