diff options
Diffstat (limited to 'src/dpdk_lib18/librte_pmd_ixgbe/ixgbe_82599_bypass.c')
| -rwxr-xr-x | src/dpdk_lib18/librte_pmd_ixgbe/ixgbe_82599_bypass.c | 314 |
1 files changed, 314 insertions, 0 deletions
diff --git a/src/dpdk_lib18/librte_pmd_ixgbe/ixgbe_82599_bypass.c b/src/dpdk_lib18/librte_pmd_ixgbe/ixgbe_82599_bypass.c new file mode 100755 index 00000000..12cc01d5 --- /dev/null +++ b/src/dpdk_lib18/librte_pmd_ixgbe/ixgbe_82599_bypass.c @@ -0,0 +1,314 @@ +/*- + * BSD LICENSE + * + * Copyright(c) 2010-2014 Intel Corporation. All rights reserved. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Intel Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +#include "ixgbe/ixgbe_type.h" +#include "ixgbe/ixgbe_82599.h" +#include "ixgbe/ixgbe_api.h" +#include "ixgbe/ixgbe_common.h" +#include "ixgbe/ixgbe_phy.h" +#include "ixgbe_bypass_defines.h" +#include "ixgbe_bypass.h" + +/** + * ixgbe_set_fiber_fixed_speed - Set module link speed for fixed fiber + * @hw: pointer to hardware structure + * @speed: link speed to set + * + * We set the module speed differently for fixed fiber. For other + * multi-speed devices we don't have an error value so here if we + * detect an error we just log it and exit. + */ +static void +ixgbe_set_fiber_fixed_speed(struct ixgbe_hw *hw, ixgbe_link_speed speed) +{ + s32 status; + u8 rs, eeprom_data; + + switch (speed) { + case IXGBE_LINK_SPEED_10GB_FULL: + /* one bit mask same as setting on */ + rs = IXGBE_SFF_SOFT_RS_SELECT_10G; + break; + case IXGBE_LINK_SPEED_1GB_FULL: + rs = IXGBE_SFF_SOFT_RS_SELECT_1G; + break; + default: + PMD_DRV_LOG(ERR, "Invalid fixed module speed"); + return; + } + + /* Set RS0 */ + status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + &eeprom_data); + if (status) { + PMD_DRV_LOG(ERR, "Failed to read Rx Rate Select RS0"); + goto out; + } + + eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) & rs; + + status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + eeprom_data); + if (status) { + PMD_DRV_LOG(ERR, "Failed to write Rx Rate Select RS0"); + goto out; + } + + /* Set RS1 */ + status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + &eeprom_data); + if (status) { + PMD_DRV_LOG(ERR, "Failed to read Rx Rate Select RS1"); + goto out; + } + + eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) & rs; + + status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + eeprom_data); + if (status) { + PMD_DRV_LOG(ERR, "Failed to write Rx Rate Select RS1"); + goto out; + } +out: + return; +} + +/** + * ixgbe_setup_mac_link_multispeed_fixed_fiber - Set MAC link speed + * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg_wait_to_complete: true when waiting for completion is needed + * + * Set the link speed in the AUTOC register and restarts link. + **/ +static s32 +ixgbe_setup_mac_link_multispeed_fixed_fiber(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + bool autoneg_wait_to_complete) +{ + s32 status = IXGBE_SUCCESS; + ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN; + ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN; + u32 speedcnt = 0; + u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP); + u32 i = 0; + bool link_up = false; + bool negotiation; + + PMD_INIT_FUNC_TRACE(); + + /* Mask off requested but non-supported speeds */ + status = ixgbe_get_link_capabilities(hw, &link_speed, &negotiation); + if (status != IXGBE_SUCCESS) + return status; + + speed &= link_speed; + + /* + * Try each speed one by one, highest priority first. We do this in + * software because 10gb fiber doesn't support speed autonegotiation. + */ + if (speed & IXGBE_LINK_SPEED_10GB_FULL) { + speedcnt++; + highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL; + + /* If we already have link at this speed, just jump out */ + status = ixgbe_check_link(hw, &link_speed, &link_up, false); + if (status != IXGBE_SUCCESS) + return status; + + if ((link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up) + goto out; + /* Set the module link speed */ + ixgbe_set_fiber_fixed_speed(hw, IXGBE_LINK_SPEED_10GB_FULL); + + /* Set the module link speed */ + esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5); + IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + IXGBE_WRITE_FLUSH(hw); + + /* Allow module to change analog characteristics (1G->10G) */ + msec_delay(40); + + status = ixgbe_setup_mac_link_82599(hw, + IXGBE_LINK_SPEED_10GB_FULL, + autoneg_wait_to_complete); + if (status != IXGBE_SUCCESS) + return status; + + /* Flap the tx laser if it has not already been done */ + ixgbe_flap_tx_laser(hw); + + /* + * Wait for the controller to acquire link. Per IEEE 802.3ap, + * Section 73.10.2, we may have to wait up to 500ms if KR is + * attempted. 82599 uses the same timing for 10g SFI. + */ + for (i = 0; i < 5; i++) { + /* Wait for the link partner to also set speed */ + msec_delay(100); + + /* If we have link, just jump out */ + status = ixgbe_check_link(hw, &link_speed, + &link_up, false); + if (status != IXGBE_SUCCESS) + return status; + + if (link_up) + goto out; + } + } + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) { + speedcnt++; + if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN) + highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL; + + /* If we already have link at this speed, just jump out */ + status = ixgbe_check_link(hw, &link_speed, &link_up, false); + if (status != IXGBE_SUCCESS) + return status; + + if ((link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up) + goto out; + + /* Set the module link speed */ + ixgbe_set_fiber_fixed_speed(hw, IXGBE_LINK_SPEED_1GB_FULL); + + /* Allow module to change analog characteristics (10G->1G) */ + msec_delay(40); + + status = ixgbe_setup_mac_link_82599(hw, + IXGBE_LINK_SPEED_1GB_FULL, + autoneg_wait_to_complete); + if (status != IXGBE_SUCCESS) + return status; + + /* Flap the tx laser if it has not already been done */ + ixgbe_flap_tx_laser(hw); + + /* Wait for the link partner to also set speed */ + msec_delay(100); + + /* If we have link, just jump out */ + status = ixgbe_check_link(hw, &link_speed, &link_up, false); + if (status != IXGBE_SUCCESS) + return status; + + if (link_up) + goto out; + } + + /* + * We didn't get link. Configure back to the highest speed we tried, + * (if there was more than one). We call ourselves back with just the + * single highest speed that the user requested. + */ + if (speedcnt > 1) + status = ixgbe_setup_mac_link_multispeed_fixed_fiber(hw, + highest_link_speed, autoneg_wait_to_complete); + +out: + /* Set autoneg_advertised value based on input link speed */ + hw->phy.autoneg_advertised = 0; + + if (speed & IXGBE_LINK_SPEED_10GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; + + return status; +} + +static enum ixgbe_media_type +ixgbe_bypass_get_media_type(struct ixgbe_hw *hw) +{ + enum ixgbe_media_type media_type; + + PMD_INIT_FUNC_TRACE(); + + if (hw->device_id == IXGBE_DEV_ID_82599_BYPASS) { + media_type = ixgbe_media_type_fiber; + } else { + media_type = ixgbe_get_media_type_82599(hw); + } + return (media_type); +} + +/* + * Wrapper around shared code (base driver) to support BYPASS nic. + */ +s32 +ixgbe_bypass_init_shared_code(struct ixgbe_hw *hw) +{ + s32 ret_val; + + if (hw->device_id == IXGBE_DEV_ID_82599_BYPASS) { + hw->mac.type = ixgbe_mac_82599EB; + } + + ret_val = ixgbe_init_shared_code(hw); + if (hw->device_id == IXGBE_DEV_ID_82599_BYPASS) { + hw->mac.ops.get_media_type = &ixgbe_bypass_get_media_type; + ixgbe_init_mac_link_ops_82599(hw); + } + + return ret_val; +} + +s32 +ixgbe_bypass_init_hw(struct ixgbe_hw *hw) +{ + int rc; + + if ((rc = ixgbe_init_hw(hw)) == 0 && + hw->device_id == IXGBE_DEV_ID_82599_BYPASS) { + + hw->mac.ops.setup_link = + &ixgbe_setup_mac_link_multispeed_fixed_fiber; + + hw->mac.ops.get_media_type = &ixgbe_bypass_get_media_type; + + hw->mac.ops.disable_tx_laser = NULL; + hw->mac.ops.enable_tx_laser = NULL; + hw->mac.ops.flap_tx_laser = NULL; + } + + return (rc); +} |