feat(docs): Static content update

Signed-off-by: Peter Mikus <pmikus@cisco.com>
Change-Id: I1cdd628be1d358fcca4bf05c9357c195ee3a8288

1 files changed, 0 insertions, 110 deletions

diff --git a/docs/report/introduction/methodology_mellanox_nic.rst b/docs/report/introduction/methodology_mellanox_nic.rst
deleted file mode 100644
index 7f8a8a0c31..0000000000
--- a/docs/report/introduction/methodology_mellanox_nic.rst
+++ /dev/null
@@ -1,110 +0,0 @@
-Mellanox NIC
-------------
-
-Performance test results using Mellanox ConnectX5 2p100GE are reported for
-2-Node Xeon Cascade Lake physical testbed type present in FD.io labs. For
-description of physical testbeds used please refer to
-:ref:`tested_physical_topologies`.
-
-Mellanox NIC settings
-~~~~~~~~~~~~~~~~~~~~~
-
-Mellanox ConnectX5 NIC settings are following recommendations from
-[DpdkPerformanceReport]_, [MellanoxDpdkGuide]_ and [MellanoxDpdkBits]_.
-Specifically:
-
-- Flow Control OFF:
-  ::
-
-      $ ethtool -A $netdev rx off tx off
-
-- Set CQE COMPRESSION to "AGGRESSIVE":
-  ::
-
-      $ mlxconfig -d $PORT_PCI_ADDRESS set CQE_COMPRESSION=1
-
-Mellanox :abbr:`OFED (OpenFabrics Enterprise Distribution)` driver is installed
-and used to manage the NIC settings.
-
-::
-
-    $ sudo lspci -vvvs 5e:00.0
-    5e:00.0 Ethernet controller: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
-	    Subsystem: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
-	    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
-	    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
-	    Latency: 0, Cache Line Size: 32 bytes
-	    Interrupt: pin A routed to IRQ 37
-	    NUMA node: 0
-	    Region 0: Memory at 38fffe000000 (64-bit, prefetchable) [size=32M]
-	    Expansion ROM at c5e00000 [disabled] [size=1M]
-	    Capabilities: [60] Express (v2) Endpoint, MSI 00
-		    DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
-			    ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
-		    DevCtl:	Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
-			    RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ FLReset-
-			    MaxPayload 256 bytes, MaxReadReq 4096 bytes
-		    DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
-		    LnkCap:	Port #0, Speed 16GT/s, Width x16, ASPM not supported, Exit Latency L0s unlimited, L1 unlimited
-			    ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
-		    LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
-			    ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
-		    LnkSta:	Speed 8GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
-		    DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported
-		    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
-		    LnkCtl2: Target Link Speed: 16GT/s, EnterCompliance- SpeedDis-
-			     Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
-			     Compliance De-emphasis: -6dB
-		    LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete+, EqualizationPhase1+
-			     EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-
-	    Capabilities: [48] Vital Product Data
-		    Product Name: CX556A - ConnectX-5 QSFP28
-		    Read-only fields:
-			    [PN] Part number: MCX556A-EDAT
-			    [EC] Engineering changes: AA
-			    [V2] Vendor specific: MCX556A-EDAT
-			    [SN] Serial number: MT1945X00360
-			    [V3] Vendor specific: f8d15ef7e701ea118000b8599ffe4aa8
-			    [VA] Vendor specific: MLX:MODL=CX556A:MN=MLNX:CSKU=V2:UUID=V3:PCI=V0
-			    [V0] Vendor specific: PCIeGen4 x16
-			    [RV] Reserved: checksum good, 2 byte(s) reserved
-		    End
-	    Capabilities: [9c] MSI-X: Enable+ Count=64 Masked-
-		    Vector table: BAR=0 offset=00002000
-		    PBA: BAR=0 offset=00003000
-	    Capabilities: [c0] Vendor Specific Information: Len=18 <?>
-	    Capabilities: [40] Power Management version 3
-		    Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
-		    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
-	    Capabilities: [100 v1] Advanced Error Reporting
-		    UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
-		    UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
-		    UESvrt:	DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
-		    CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
-		    CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
-		    AERCap:	First Error Pointer: 04, GenCap+ CGenEn- ChkCap+ ChkEn-
-	    Capabilities: [150 v1] Alternative Routing-ID Interpretation (ARI)
-		    ARICap:	MFVC- ACS-, Next Function: 1
-		    ARICtl:	MFVC- ACS-, Function Group: 0
-	    Capabilities: [1c0 v1] #19
-	    Capabilities: [230 v1] Access Control Services
-		    ACSCap:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
-		    ACSCtl:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
-	    Capabilities: [320 v1] #27
-	    Capabilities: [370 v1] #26
-	    Capabilities: [420 v1] #25
-	    Kernel driver in use: mlx5_core
-	    Kernel modules: mlx5_core
-
-TG and SUT settings
-~~~~~~~~~~~~~~~~~~~
-
-For the TG and SUT environment settings please refer to
-:ref:`_vpp_test_environment` and :ref:`_dpdk_test_environment`.
-
-Links
-~~~~~
-
-.. [DpdkPerformanceReport] `DPDK 19.11 performance report <http://static.dpdk.org/doc/perf/DPDK_19_11_Mellanox_NIC_performance_report.pdf>`
-.. [MellanoxDpdkGuide] `Mellanox DPDK guide <https://www.mellanox.com/related-docs/prod_software/MLNX_DPDK_Quick_Start_Guide_v16.11_3.0.pdf>`
-.. [MellanoxDpdkBits] `Mellanox DPDK bits <https://community.mellanox.com/s/article/mellanox-dpdk>`