Refactor DPDK testcases to new structure

+ RXQ refactor

Change-Id: Ic03a2e208b9fe5d324a5ed75a603af4cff1854a9
Signed-off-by: Peter Mikus <pmikus@cisco.com>

1 files changed, 0 insertions, 421 deletions

diff --git a/tests/dpdk/perf/10ge2p1x520-ethip4-ip4base-l3fwd-ndrpdrdisc.robot b/tests/dpdk/perf/10ge2p1x520-ethip4-ip4base-l3fwd-ndrpdrdisc.robot
deleted file mode 100644
index fe6b5b261e..0000000000
--- a/tests/dpdk/perf/10ge2p1x520-ethip4-ip4base-l3fwd-ndrpdrdisc.robot
+++ /dev/null
@@ -1,421 +0,0 @@
-# Copyright (c) 2018 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance/performance_setup.robot
-| Resource | resources/libraries/robot/dpdk/default.robot
-| Library | resources.libraries.python.topology.Topology
-| Library | resources.libraries.python.NodePath
-| Library | resources.libraries.python.InterfaceUtil
-| Library | resources.libraries.python.DPDK.DPDKTools
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC | 1NUMA
-| ... | NIC_Intel-X520-DA2 | DPDK | IP4FWD | BASE | ETH
-| Suite Setup | Set up DPDK 3-node performance topology with DUT's NIC model
-| ... | L3 | Intel-X520-DA2
-| Suite Teardown | Tear down DPDK 3-node performance topology
-| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L3 IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 run the DPDK l3fwd application
-| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using either binary search or linear search
-| ... | algorithms with configured starting rate and final step that determines
-| ... | throughput measurement resolution. Test packets are generated by TG on
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
-| ... | (flow-group per direction, 253 flows per flow-group) with all packets
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static
-| ... | payload. MAC addresses are matching MAC addresses of the TG node
-| ... | interfaces.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Variables ***
-# X520-DA2 bandwidth limit
-| ${s_limit} | ${10000000000}
-# Traffic profile:
-| ${traffic_profile} | trex-sl-3n-ethip4-ip4dst253_l3fwd
-
-*** Test Cases ***
-| tc01-64B-1t1c-ethip4-ip4base-l3fwd-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 64 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 100kpps.
-| | ...
-| | [Tags] | 64B | 1C | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 1 | 1 | no
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc02-64B-1t1c-ethip4-ip4base-l3fwd-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find PDR for 64 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
-| | ...
-| | [Tags] | 64B | 1C | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 1 | 1 | no
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc03-1518B-1t1c-ethip4-ip4base-l3fwd-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 10kpps.
-| | ...
-| | [Tags] | 1518B | 1C | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 1 | 1 | no
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc04-1518B-1t1c-ethip4-ip4base-l3fwd-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
-| | ...
-| | [Tags] | 1518B | 1C | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 1 | 1 | no
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc05-9000B-1t1c-ethip4-ip4base-l3fwd-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 5kpps.
-| | ...
-| | [Tags] | 9000B | 1C | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 1 | 1 | yes
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc06-9000B-1t1c-ethip4-ip4base-l3fwd-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
-| | ...
-| | [Tags] | 9000B | 1C | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 1 | 1 | yes
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc07-64B-2t2c-ethip4-ip4base-l3fwd-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 64 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 100kpps.
-| | ...
-| | [Tags] | 64B | 2C | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 2 | 1 | no
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc08-64B-2t2c-ethip4-ip4base-l3fwd-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find PDR for 64 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
-| | ...
-| | [Tags] | 64B | 2C | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 2 | 1 | no
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc09-1518B-2t2c-ethip4-ip4base-l3fwd-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 10kpps.
-| | ...
-| | [Tags] | 1518B | 2C | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 2 | 1 | no
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc10-1518B-2t2c-ethip4-ip4base-l3fwd-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
-| | ...
-| | [Tags] | 1518B | 2C | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 2 | 1 | no
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc11-9000B-2t2c-ethip4-ip4base-l3fwd-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 5kpps.
-| | ...
-| | [Tags] | 9000B | 2C | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 2 | 1 | yes
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc12-9000B-2t2c-ethip4-ip4base-l3fwd-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
-| | ...
-| | [Tags] | 9000B | 2C | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 2 | 1 | yes
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc13-64B-4t4c-ethip4-ip4base-l3fwd-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Find NDR for 64 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 100kpps.
-| | ...
-| | [Tags] | 64B | 4C | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 4 | 2 | no
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc14-64B-4t4c-ethip4-ip4base-l3fwd-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Find PDR for 64 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
-| | ...
-| | [Tags] | 64B | 4C | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 4 | 2 | no
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc15-1518B-4t4c-ethip4-ip4base-l3fwd-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 10kpps.
-| | ...
-| | [Tags] | 1518B | 4C | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 4 | 2 | no
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc16-1518B-4t4c-ethip4-ip4base-l3fwd-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
-| | ...
-| | [Tags] | 1518B | 4C | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 4 | 2 | no
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc17-9000B-4t4c-ethip4-ip4base-l3fwd-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 5kpps.
-| | ...
-| | [Tags] | 9000B | 4C | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 4 | 2 | yes
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc18-9000B-4t4c-ethip4-ip4base-l3fwd-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\
-| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
-| | ...
-| | [Tags] | 9000B | 4C | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Start L3FWD on all DUTs | 4 | 2 | yes
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}