CSIT-687: Directory structure reorganization

Change-Id: I772c9e214be2461adf58124998d272e7d795220f
Signed-off-by: Tibor Frank <tifrank@cisco.com>
Signed-off-by: Maciek Konstantynowicz <mkonstan@cisco.com>

5 files changed, 1679 insertions, 0 deletions

diff --git a/tests/dpdk/perf/10ge2p1x520-eth-l2xcbase-testpmd-ndrpdrdisc.robot b/tests/dpdk/perf/10ge2p1x520-eth-l2xcbase-testpmd-ndrpdrdisc.robot
new file mode 100644
index 0000000000..962552dae4
--- /dev/null
+++ b/tests/dpdk/perf/10ge2p1x520-eth-l2xcbase-testpmd-ndrpdrdisc.robot
@@ -0,0 +1,374 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/dpdk/default.robot
+| Library | resources.libraries.python.topology.Topology
+| Library | resources.libraries.python.NodePath
+| Library | resources.libraries.python.InterfaceUtil
+| Library | resources.libraries.python.DPDK.DPDKTools
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | PERFTEST | NDRPDRDISC | 1NUMA
+| ... | NIC_Intel-X520-DA2 | DPDK | ETH | L2XCFWD | BASE
+| Suite Setup | Set up DPDK 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down DPDK 3-node performance topology
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 frame forwarding.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 run the DPDK testpmd\
+| ... | application and use the io forwarding mode. DUT1 and DUT2 tested with\
+| ... | 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets\
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
+| ... | payload. MAC addresses are matching MAC addresses of the TG node\
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit} | ${10000000000}
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames\
+| | ... | using binary search start at 10GE linerate, step 100kpps.
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc02-64B-1t1c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames\
+| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc03-1518B-1t1c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames\
+| | ... | using binary search start at 10GE linerate, step 10kpps.
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc04-1518B-1t1c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames\
+| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc05-9000B-1t1c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames\
+| | ... | using binary search start at 10GE linerate, step 10kpps.
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc06-9000B-1t1c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames\
+| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc07-64B-2t2c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 100kpps.
+| | [Tags] | 2T2C | MTHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc08-64B-2t2c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 100kpps,\
+| | ... | LT=0.5%.
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc09-1518B-2t2c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 10kpps.
+| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc10-1518B-2t2c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 10kpps,\
+| | ... | LT=0.5%.
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc11-9000B-2t2c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 10kpps.
+| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc12-9000B-2t2c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 10kpps,\
+| | ... | LT=0.5%.
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc13-64B-4t4c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 100kpps.
+| | [Tags] | 4T4C | MTHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc14-64B-4t4c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 100kpps,\
+| | ... | LT=0.5%.
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc15-1518B-4t4c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 10kpps.
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc16-1518B-4t4c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 10kpps,\
+| | ... | LT=0.5%.
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc17-9000B-4t4c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte\
+| | ... | frames using binary search start at 10GE linerate, step 10kpps.
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc18-9000B-4t4c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte
+| | ... | frames using binary search start at 10GE linerate, step 5kpps,\
+| | ... | LT=0.5%.
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
diff --git a/tests/dpdk/perf/10ge2p1x520-ethip4-ip4base-l3fwd-ndrpdrdisc.robot b/tests/dpdk/perf/10ge2p1x520-ethip4-ip4base-l3fwd-ndrpdrdisc.robot
new file mode 100644
index 0000000000..c493c27e7b
--- /dev/null
+++ b/tests/dpdk/perf/10ge2p1x520-ethip4-ip4base-l3fwd-ndrpdrdisc.robot
@@ -0,0 +1,421 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/dpdk/default.robot
+| Library | resources.libraries.python.topology.Topology
+| Library | resources.libraries.python.NodePath
+| Library | resources.libraries.python.InterfaceUtil
+| Library | resources.libraries.python.DPDK.DPDKTools
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC | 1NUMA
+| ... | NIC_Intel-X520-DA2 | DPDK | IP4FWD | BASE | ETH
+| Suite Setup | Set up DPDK 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | Tear down DPDK 3-node performance topology
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L3 IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 run the DPDK l3fwd application
+| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using either binary search or linear search
+| ... | algorithms with configured starting rate and final step that determines
+| ... | throughput measurement resolution. Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static
+| ... | payload. MAC addresses are matching MAC addresses of the TG node
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit} | ${10000000000}
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip4-ip4dst253_l3fwd
+
+*** Test Cases ***
+| tc01-64B-1t1c-ethip4-ip4base-l3fwd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc02-64B-1t1c-ethip4-ip4base-l3fwd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc03-1518B-1t1c-ethip4-ip4base-l3fwd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc04-1518B-1t1c-ethip4-ip4base-l3fwd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc05-9000B-1t1c-ethip4-ip4base-l3fwd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '1' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc06-9000B-1t1c-ethip4-ip4base-l3fwd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '1' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc07-64B-2t2c-ethip4-ip4base-l3fwd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc08-64B-2t2c-ethip4-ip4base-l3fwd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc09-1518B-2t2c-ethip4-ip4base-l3fwd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc10-1518B-2t2c-ethip4-ip4base-l3fwd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc11-9000B-2t2c-ethip4-ip4base-l3fwd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '2' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc12-9000B-2t2c-ethip4-ip4base-l3fwd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '2' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc13-64B-4t4c-ethip4-ip4base-l3fwd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc14-64B-4t4c-ethip4-ip4base-l3fwd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc15-1518B-4t4c-ethip4-ip4base-l3fwd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc16-1518B-4t4c-ethip4-ip4base-l3fwd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc17-9000B-4t4c-ethip4-ip4base-l3fwd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '4' worker threads and '2' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc18-9000B-4t4c-ethip4-ip4base-l3fwd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L3FWD '4' worker threads and '2' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile} | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
diff --git a/tests/dpdk/perf/10ge2p1x710-eth-l2xcbase-testpmd-ndrpdrdisc.robot b/tests/dpdk/perf/10ge2p1x710-eth-l2xcbase-testpmd-ndrpdrdisc.robot
new file mode 100644
index 0000000000..148c4ddd35
--- /dev/null
+++ b/tests/dpdk/perf/10ge2p1x710-eth-l2xcbase-testpmd-ndrpdrdisc.robot
@@ -0,0 +1,422 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/dpdk/default.robot
+| Library | resources.libraries.python.topology.Topology
+| Library | resources.libraries.python.NodePath
+| Library | resources.libraries.python.InterfaceUtil
+| Library | resources.libraries.python.DPDK.DPDKTools
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | PERFTEST | NDRPDRDISC | 1NUMA
+| ... | NIC_Intel-X710 | DPDK | ETH | L2XCFWD | BASE
+| Suite Setup | Set up DPDK 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X710
+| Suite Teardown | Tear down DPDK 3-node performance topology
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 frame forwarding.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 run the DPDK testpmd\
+| ... | application and use the io forwarding mode. DUT1 and DUT2 tested with\
+| ... | 2p10GE NIC X710 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets\
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
+| ... | payload. MAC addresses are matching MAC addresses of the TG node\
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit} | ${10000000000}
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc02-64B-1t1c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc03-1518B-1t1c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc04-1518B-1t1c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc05-9000B-1t1c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc06-9000B-1t1c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc07-64B-2t2c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc08-64B-2t2c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc09-1518B-2t2c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc10-1518B-2t2c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc11-9000B-2t2c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc12-9000B-2t2c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc13-64B-4t4c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc14-64B-4t4c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc15-1518B-4t4c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc16-1518B-4t4c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc17-9000B-4t4c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc18-9000B-4t4c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 5kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
\ No newline at end of file
diff --git a/tests/dpdk/perf/40ge2p1xl710-eth-l2xcbase-testpmd-ndrpdrdisc.robot b/tests/dpdk/perf/40ge2p1xl710-eth-l2xcbase-testpmd-ndrpdrdisc.robot
new file mode 100644
index 0000000000..5d5418c6c1
--- /dev/null
+++ b/tests/dpdk/perf/40ge2p1xl710-eth-l2xcbase-testpmd-ndrpdrdisc.robot
@@ -0,0 +1,424 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/dpdk/default.robot
+| Library | resources.libraries.python.topology.Topology
+| Library | resources.libraries.python.NodePath
+| Library | resources.libraries.python.InterfaceUtil
+| Library | resources.libraries.python.DPDK.DPDKTools
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | PERFTEST | NDRPDRDISC | 1NUMA
+| ... | NIC_Intel-XL710 | DPDK | ETH | L2XCFWD | BASE
+| Suite Setup | Set up DPDK 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-XL710
+| Suite Teardown | Tear down DPDK 3-node performance topology
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 frame forwarding.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 run the DPDK testpmd\
+| ... | application and use the io forwarding mode. DUT1 and DUT2 tested with\
+| ... | 2p40GE NIC XL710 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets\
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
+| ... | payload. MAC addresses are matching MAC addresses of the TG node\
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc02-64B-1t1c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc03-1518B-1t1c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc04-1518B-1t1c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc05-9000B-1t1c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc06-9000B-1t1c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '1' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc07-64B-2t2c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc08-64B-2t2c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc09-1518B-2t2c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc10-1518B-2t2c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc11-9000B-2t2c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc12-9000B-2t2c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '2' worker threads and '1' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc13-64B-4t4c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc14-64B-4t4c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc15-1518B-4t4c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc16-1518B-4t4c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'no'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
+
+| tc17-9000B-4t4c-eth-l2xcbase-testpmd-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'yes'
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc18-9000B-4t4c-eth-l2xcbase-testpmd-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 5kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Start L2FWD '4' worker threads and '2' rxqueues with jumbo frames 'yes'
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
+| | ... | ${perf_pdr_loss_acceptance_type}
\ No newline at end of file
diff --git a/tests/dpdk/perf/__init__.robot b/tests/dpdk/perf/__init__.robot
new file mode 100644
index 0000000000..5801fd1b25
--- /dev/null
+++ b/tests/dpdk/perf/__init__.robot
@@ -0,0 +1,38 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/shared/default.robot
+| Resource | resources/libraries/robot/shared/interfaces.robot
+| Library | resources.libraries.python.DPDK.SetupDPDKTest
+| Suite Setup | Run Keywords | Setup performance global Variables
+| ...         | AND          | Setup DPDK Test | ${nodes}
+| ...         | AND          | Get CPU Layout from all nodes | ${nodes}
+| ...         | AND          | Update All Numa Nodes
+| ...                        | ${nodes} | skip_tg=${True}
+
+*** Keywords ***
+| Setup performance global Variables
+| | [Documentation]
+| | ... | Setup suite Variables. Variables are used across performance testing.
+| | ...
+| | ... | _NOTE:_ This KW sets following suite variables:
+| | ... | - perf_trial_duration - Duration of traffic run [s].
+| | ... | - perf_pdr_loss_acceptance - Loss acceptance treshold
+| | ... | - perf_pdr_loss_acceptance_type - Loss acceptance treshold type
+| | ... | - perf_vm_image - Guest VM disk image
+| | ...
+| | Set Global Variable | ${perf_trial_duration} | 10
+| | Set Global Variable | ${perf_pdr_loss_acceptance} | 0.5
+| | Set Global Variable | ${perf_pdr_loss_acceptance_type} | percentage
+| | Set Global Variable | ${perf_vm_image} | /var/lib/vm/csit-nested-1.6.img