csit-func-tc-naming-change - phase 1

- change of ts directories
- change of ts file names
- splitting of former files to more files when suitable
- more details:
  https://wiki.fd.io/view/CSIT/csit-perf-tc-naming-change

Change-Id: Ifda1038f8323735f86c1be7ba7f93e3fda183618
Signed-off-by: Jan Gelety <jgelety@cisco.com>

1 files changed, 123 insertions, 0 deletions

diff --git a/tests/func/tap/eth2p-ethip4-ip4base-eth-1tap-func.robot b/tests/func/tap/eth2p-ethip4-ip4base-eth-1tap-func.robot
new file mode 100644
index 0000000000..bd767e704c
--- /dev/null
+++ b/tests/func/tap/eth2p-ethip4-ip4base-eth-1tap-func.robot
@@ -0,0 +1,123 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/default.robot
+| Resource | resources/libraries/robot/ipv4.robot
+| Resource | resources/libraries/robot/ipv6.robot
+| Resource | resources/libraries/robot/interfaces.robot
+| Resource | resources/libraries/robot/bridge_domain.robot
+| Resource | resources/libraries/robot/testing_path.robot
+| Resource | resources/libraries/robot/traffic.robot
+| Library  | resources.libraries.python.Trace
+| Library  | resources.libraries.python.Tap
+| Library  | resources.libraries.python.Namespaces
+| Library  | resources.libraries.python.IPUtil
+| Force Tags | HW_ENV | VM_ENV | 3_NODE_DOUBLE_LINK_TOPO
+| Test Setup | Run Keywords | Func Test Setup
+| ...        | AND          | Clean Up Namespaces | ${nodes['DUT1']}
+| Test Teardown | Run Keywords | Func Test Teardown
+| ...           | AND          | Clean Up Namespaces | ${nodes['DUT1']}
+| Documentation | *Tap Interface Traffic Tests*
+| ... | *[Top] Network Topologies:* TG=DUT1 2-node topology with two links
+| ... | between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-ICMPv4 for L2 switching of
+| ... | IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2
+| ... | bridge-domain (L2BD) MAC learning enabled; Split Horizon Groups (SHG)
+| ... | are set depending on test case; Namespaces (NM)
+| ... | are set on DUT1 with attached linux-TAP.
+| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets
+| ... | are sent by TG on link to DUT1; On receipt TG verifies packets
+| ... | for correctness and their IPv4 src-addr, dst-addr, and MAC addresses.
+| ... | *[Ref] Applicable standard specifications:*
+
+*** Variables ***
+| ${tap1_VPP_ip}= | 16.0.10.1
+| ${tap1_NM_ip}= | 16.0.10.2
+| ${tap1_NM_mac}= | 02:00:00:00:00:02
+| ${tap_int1}= | tap_int1
+
+| ${namespace1}= | nmspace1
+
+| ${dut_ip_address}= | 192.168.0.1
+| ${tg_ip_address}= | 192.168.0.2
+| ${tg_ip_address_GW}= | 192.168.0.0
+| ${prefix}= | 24
+
+*** Test Cases ***
+| TC01: Tap Interface IP Ping Without Namespace
+| | [Documentation]
+| | ... | [Top] TG-DUT1-TG.
+| | ... | [Enc] Eth-IPv4-ICMPv4.
+| | ... | [Cfg] On DUT1 configure two interface addresses with IPv4 of which
+| | ... | one is TAP interface ( dut_to_tg_if and TAP ).
+| | ... | and one is linux-TAP.
+| | ... | [Ver] Packet sent from TG gets to the destination and ICMP-reply is
+| | ... | received on TG.
+| | Given Path for 2-node testing is set | ${nodes['TG']} | ${nodes['DUT1']}
+| | ... | ${nodes['TG']}
+| | And Interfaces in 2-node path are up
+| | ${int1}= | And Add Tap Interface | ${dut_node} | ${tap_int1} |
+| | And Set Interface Address
+| | ... | ${dut_node} | ${int1} | ${tap1_VPP_ip} | ${prefix}
+| | And Set Interface Address
+| | ... | ${dut_node} | ${dut_to_tg_if1} | ${dut_ip_address} | ${prefix}
+| | And Set Interface State | ${dut_node} | ${int1} | up
+| | And Set Linux Interface MAC | ${dut_node} | ${tap_int1} | ${tap1_NM_mac}
+| | And Set Linux Interface IP | ${dut_node}
+| | ... | ${tap_int1} | ${tap1_NM_ip} | ${prefix}
+| | And Add Route | ${dut_node}
+| | ... | ${tg_ip_address_GW} | ${prefix} | ${tap1_VPP_ip}
+| | And Add Arp On Dut | ${dut_node} | ${dut_to_tg_if1}
+| | ... | ${tg_ip_address} | ${tg_to_dut_if1_mac}
+| | And Add Arp On Dut | ${dut_node} | ${int1}
+| | ... | ${tap1_NM_ip} | ${tap1_NM_mac}
+| | Then Node replies to ICMP echo request | ${tg_node} | ${tg_to_dut_if1}
+| | ... | ${dut_to_tg_if1_mac} | ${tg_to_dut_if1_mac}
+| | ... | ${tap1_NM_ip} | ${tg_ip_address}
+
+| TC02: Tap Interface IP Ping With Namespace
+| | [Documentation]
+| | ... | [Top] TG-DUT1-TG.
+| | ... | [Enc] Eth-IPv4-ICMPv4.
+| | ... | [Cfg] On DUT1 configure two interface addresses with IPv4 of which
+| | ... | one is TAP interface ( dut_to_tg_if and TAP ).
+| | ... | and one is linux-TAP in namespace.
+| | ... | [Ver] Packet sent from TG gets to the destination and ICMP-reply is
+| | ... | received on TG.
+| | Given Path for 2-node testing is set | ${nodes['TG']} | ${nodes['DUT1']}
+| | ... | ${nodes['TG']}
+| | And Interfaces in 2-node path are up
+| | ${int1}= | And Add Tap Interface | ${dut_node} | ${tap_int1} |
+| | And Set Interface Address
+| | ... | ${dut_node} | ${int1} | ${tap1_VPP_ip} | ${prefix}
+| | And Set Interface Address
+| | ... | ${dut_node} | ${dut_to_tg_if1} | ${dut_ip_address} | ${prefix}
+| | And Set Interface State | ${dut_node} | ${int1} | up
+| | When Create Namespace | ${dut_node} | ${namespace1}
+| | And Attach Interface To Namespace | ${dut_node}
+| | ... | ${namespace1} | ${tap_int1}
+| | And Set Linux Interface MAC | ${dut_node}
+| | ... | ${tap_int1} | ${tap1_NM_mac} | ${namespace1}
+| | And Set Linux Interface IP | ${dut_node}
+| | ... | ${tap_int1} | ${tap1_NM_ip} | ${prefix} | ${namespace1}
+| | And Add Arp On Dut | ${dut_node} | ${dut_to_tg_if1}
+| | ... | ${tg_ip_address} | ${tg_to_dut_if1_mac}
+| | And Add Arp On Dut | ${dut_node} | ${int1}
+| | ... | ${tap1_NM_ip} | ${tap1_NM_mac}
+| | And Add Route | ${dut_node}
+| | ... | ${tg_ip_address_GW} | ${prefix} | ${tap1_VPP_ip} | ${namespace1}
+| | Then Node replies to ICMP echo request | ${tg_node} | ${tg_to_dut_if1}
+| | ... | ${dut_to_tg_if1_mac} | ${tg_to_dut_if1_mac}
+| | ... | ${tap1_NM_ip} | ${tg_ip_address}