HONEYCOMB: Remove

Signed-off-by: Peter Mikus <pmikus@cisco.com>
Change-Id: I60d80564050cb786c7b1e0a08f31f8292f82197e

1 files changed, 0 insertions, 364 deletions

diff --git a/tests/honeycomb/func/mgmt-cfg-bgp-apihc-func.robot b/tests/honeycomb/func/mgmt-cfg-bgp-apihc-func.robot
deleted file mode 100644
index 26a9de6f5a..0000000000
--- a/tests/honeycomb/func/mgmt-cfg-bgp-apihc-func.robot
+++ /dev/null
@@ -1,364 +0,0 @@
-# Copyright (c) 2017 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Variables ***
-# Interface to run tests on.
-| ${interface}= | ${node['interfaces']['port1']['name']}
-| ${dut1_to_tg_ip}= | 192.168.0.1
-| ${tg_to_dut1_ip}= | 192.168.0.2
-| ${dut1_to_dut2_ip}= | 192.168.1.1
-| ${dut2_to_dut1_ip}= | 192.168.1.2
-| ${bgp_port}= | ${179}
-| ${bgp_as_number}= | ${37}
-| ${prefix}= | ${24}
-
-*** Settings ***
-| Library | resources.libraries.python.honeycomb.IPv6Management
-| Resource | resources/libraries/robot/shared/default.robot
-| Resource | resources/libraries/robot/honeycomb/honeycomb.robot
-| Resource | resources/libraries/robot/honeycomb/interfaces.robot
-| Resource | resources/libraries/robot/honeycomb/bgp.robot
-| Resource | resources/libraries/robot/honeycomb/routing.robot
-| Resource | resources/libraries/robot/shared/testing_path.robot
-| Resource | resources/libraries/robot/honeycomb/ipv6_control.robot
-| Variables | resources/test_data/honeycomb/bgp.py
-| ...
-| Suite Setup | Run Keywords
-| ... | Enable Honeycomb Feature | ${node} | BGP | AND
-| ... | Configure BGP Module | ${node} | ${dut1_to_tg_ip}
-| ... | ${bgp_port} | ${bgp_as_number} | AND
-| ... | Set Up Honeycomb Functional Test Suite | ${node}
-| ...
-| Suite Teardown | Run Keywords
-| ... | Tear Down Honeycomb Functional Test Suite | ${nodes['DUT1']} | AND
-| ... | Stop Honeycomb service on DUTs | ${nodes['DUT2']} | AND
-| ... | Unconfigure IPv4 Management Interfaces | AND
-| ... | Disable Honeycomb Feature | ${node} | BGP | AND
-| ... | Disable Honeycomb Feature | ${nodes['DUT2']} | BGP
-| ...
-# HONEYCOMB-409: BGP configuration via ODL is currently not fully supported
-| Force Tags | HC_FUNC | HC_REST_ONLY
-| ...
-| Documentation | *Honeycomb BGP management test suite.*
-
-*** Test Cases ***
-| TC01: Honeycomb configures BGP peer - Internal
-| | [Documentation] | Check if Honeycomb can configure an internal BGP peer.
-| | ...
-| | When Honeycomb adds BGP peer
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-| | Then BGP peer from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-
-| TC02: Honeycomb removes peer configuration
-| | [Documentation] | Check if Honeycomb can remove a configured BGP peer.
-| | ...
-| | Given BGP peer from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-| | When Honeycomb removes BGP peer | ${node} | ${address_internal}
-| | Then No BGP peers should be configured | ${node}
-
-| TC03: Honeycomb updates existing BGP peer - Internal
-| | [Documentation] | Check if Honeycomb can update an existing BGP peer.
-| | ...
-| | [Teardown] | Honeycomb removes BGP peer | ${node} | ${address_internal}
-| | ...
-| | Given No BGP peers should be configured | ${node}
-| | When Honeycomb adds BGP peer
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-| | And Honeycomb adds BGP peer
-| | ... | ${node} | ${address_internal} | ${peer_internal_update}
-| | Then BGP peer from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${peer_internal_update}
-
-| TC04: Honeycomb configures BGP peer - Application
-| | [Documentation] | Check if Honeycomb can configure an application BGP peer.
-| | ...
-| | [Teardown] | Honeycomb removes BGP peer | ${node} | ${address_application}
-| | ...
-| | Given No BGP peers should be configured | ${node}
-| | When Honeycomb adds BGP peer
-| | ... | ${node} | ${address_application} | ${peer_application}
-| | Then BGP peer from Honeycomb should be
-| | ... | ${node} | ${address_application} | ${peer_application}
-
-| TC05: Honeycomb configures a second BGP peer
-| | [Documentation] | Check if Honeycomb can configure more than one BGP peer.
-| | ...
-| | [Teardown] | Run Keywords
-| | ... | Honeycomb removes BGP peer | ${node} | ${address_internal} | AND
-| | ... | Honeycomb removes BGP peer | ${node} | ${address_internal2}
-| | ...
-| | Given No BGP peers should be configured | ${node}
-| | When Honeycomb adds BGP peer
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-| | And Honeycomb adds BGP peer
-| | ... | ${node} | ${address_internal2} | ${peer_internal2}
-| | Then BGP peer from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-| | And BGP peer from Honeycomb should be
-| | ... | ${node} | ${address_internal2} | ${peer_internal2}
-
-| TC06: Honeycomb configures IPv4 route using BGP
-| | [Documentation] | Check if Honeycomb can configure a BGP route under a peer.
-| | ...
-| | Given Honeycomb adds BGP peer
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-| | When Honeycomb configures BGP route
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-| | Then BGP Route from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4_oper}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-
-| TC07: Honeycomb removes IPv4 route configuration
-| | [Documentation] | Check if Honeycomb can remove a configured BGP route.
-| | ...
-| | Given BGP peer from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-| | And BGP Route from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4_oper}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-| | When Honeycomb removes BGP route | ${node} | ${address_internal}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-| | Then No BGP Routes Should exist
-| | ... | ${node} | ${address_internal} | ipv4
-
-| TC08: Honeycomb updates existing IPv4 route using BGP
-| | [Documentation] | Check if Honeycomb can update an existing BGP route.
-| | ...
-| | [Teardown] | Honeycomb removes BGP route | ${node} | ${address_internal}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-| | ...
-| | Given BGP peer from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-| | And No BGP Routes Should exist
-| | ... | ${node} | ${address_internal} | ipv4
-| | When Honeycomb configures BGP route
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-| | And Honeycomb configures BGP route
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4_update}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-| | Then BGP Route from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4_update_oper}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-
-| TC09: Honeycomb configures a second IPv4 route
-| | [Documentation] | Check if Honeycomb can configure more than one BGP route.
-| | ...
-| | [Teardown] | Run Keywords
-| | ... | Honeycomb removes BGP route | ${node} | ${address_internal}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4 | AND
-| | ... | Honeycomb removes BGP route | ${node} | ${address_internal}
-| | ... | ${route_address_ipv4_2} | ${route_id_ipv4_2} | ipv4 | AND
-| | ... | Honeycomb removes BGP peer | ${node} | ${address_internal}
-| | ...
-| | Given BGP peer from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${peer_internal}
-| | When Honeycomb configures BGP route
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-| | And Honeycomb configures BGP route
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4_2}
-| | ... | ${route_address_ipv4_2} | ${route_id_ipv4_2} | ipv4
-| | Then BGP Route from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4_oper}
-| | ... | ${route_address_ipv4} | ${route_id_ipv4} | ipv4
-| | And BGP Route from Honeycomb should be
-| | ... | ${node} | ${address_internal} | ${route_data_ipv4_2_oper}
-| | ... | ${route_address_ipv4_2} | ${route_id_ipv4_2} | ipv4
-
-| TC10: Honeycomb sends BGP OPEN messages to configured peer
-| | [Documentation]
-| | ... | [top] TG-DUT1-TG.
-| | ... | [enc] Eth-IPv4-TCP-BGP.
-| | ... | [cfg] On DUT1 give Honeycomb control over the data-plane interface
-| | ... | connected to TG. Configure a BGP peer with the address of TG.
-| | ... | [ver] Open a TCP listener on TG on the BGP port and listen for BGP
-| | ... | OPEN message. On receive, verify message fields.
-| | ...
-| | [Setup] | Run Keywords
-| | ... | Configure BGP Module | ${node} | ${dut1_to_dut2_ip}
-| | ... | ${bgp_port} | ${bgp_as_number} | AND
-| | ... | Configure IPv4 Management Interface
-| | [Teardown] | Honeycomb removes BGP peer | ${dut1_node} | ${address_internal}
-| | When Honeycomb adds BGP peer
-| | ... | ${dut1_node} | ${address_internal} | ${peer_internal}
-| | Then Receive BGP OPEN message
-| | ... | ${tg_node} | ${tg_to_dut1_ip} | ${dut1_to_dut2_ip}
-| | ... | ${bgp_port} | ${bgp_as_number} | ${holdtime_internal}
-
-| TC11: Honeycomb shows connected peer in operational data
-| | [Documentation]
-| | ... | [top] TG-DUT1-DUT2-TG.
-| | ... | [enc] Eth-IPv4-TCP-BGP.
-| | ... | [cfg] On DUT1 and DUT2 give Honeycomb control over the data-plane
-| | ... | interfaces connecting DUT1 ad DUT2. Configure BGP peers on DUT1
-| | ... | and DUT2 with each other's IP address.
-| | ... | [ver] Using Restconf, verify that Honeycomb on each DUT has the
-| | ... | other DUT's entry in operational data.
-| | ...
-| | When Honeycomb adds BGP peer
-| | ... | ${dut1_node} | ${dut2_to_dut1_ip} | ${dut2_peer}
-| | And Honeycomb adds BGP peer
-| | ... | ${dut2_node} | ${dut1_to_dut2_ip} | ${dut1_peer}
-| | Sleep | 5s | Wait for BGP connection. Retry timer is 5 seconds.
-| | Then Peer operational data from Honeycomb should be
-| | ... | ${dut1_node} | ${dut2_to_dut1_ip}
-| | And Peer operational data from Honeycomb should be
-| | ... | ${dut2_node} | ${dut1_to_dut2_ip}
-
-| TC12: Honeycomb sends IPv4 BGP route to connected peer
-| | [Documentation]
-| | ... | [top] TG-DUT1-DUT2-TG.
-| | ... | [enc] Eth-IPv4-TCP-BGP.
-| | ... | [cfg] On DUT1 and DUT2 give Honeycomb control over the data-plane
-| | ... | interfaces connecting DUT1 ad DUT2. Configure BGP peers on DUT1
-| | ... | and DUT2 with each other's IP address. On DUT2 configure a static
-| | ... | IPv4 route using Honeycomb's BGP module.
-| | ... | [ver] Verify that the route is present in BGP
-| | ... | local RIB and VPP's routing table on each DUT.
-| | ...
-| | Given Peer operational data from Honeycomb should be
-| | ... | ${dut1_node} | ${dut2_to_dut1_ip}
-| | And Peer operational data from Honeycomb should be
-| | ... | ${dut2_node} | ${dut1_to_dut2_ip}
-| | When Honeycomb adds BGP peer
-| | ... | ${dut2_node} | ${address_application} | ${peer_application}
-| | And Honeycomb configures BGP route
-| | ... | ${dut2_node} | ${address_application} | ${dut1_route}
-| | ... | ${dut1_route_address} | ${dut1_route_id} | ipv4
-| | And Sleep | 5s | Wait for route advertisement. Retry timer is 5 seconds.
-| | Then Routing data from Honeycomb should contain
-| | ... | ${dut1_node} | learned-protocol-0 | ipv4 | ${route_operational}
-| | And Routing data from Honeycomb should contain
-| | ... | ${dut2_node} | learned-protocol-0 | ipv4 | ${route_operational}
-| | And BGP Loc-RIB table should include | ${dut1_node} | ${rib_operational}
-| | And BGP Loc-RIB table should include | ${dut2_node} | ${rib_operational}
-
-| TC13: Honeycomb sends IPv6 BGP route to connected peer
-| | [Documentation]
-| | ... | [top] TG-DUT1-DUT2-TG.
-| | ... | [enc] Eth-IPv4-TCP-BGP.
-| | ... | [cfg] On DUT1 and DUT2 give Honeycomb control over the data-plane
-| | ... | interfaces connecting DUT1 ad DUT2. Configure BGP peers on DUT1
-| | ... | and DUT2 with each other's IP address. On DUT2 configure a static
-| | ... | IPv6 route using Honeycomb's BGP module.
-| | ... | [ver] Verify that the route is present in BGP
-| | ... | local RIB and VPP's routing table on each DUT.
-| | ...
-| | Given Peer operational data from Honeycomb should be
-| | ... | ${dut1_node} | ${dut2_to_dut1_ip}
-| | And Peer operational data from Honeycomb should be
-| | ... | ${dut2_node} | ${dut1_to_dut2_ip}
-| | And Honeycomb adds BGP peer
-| | ... | ${dut2_node} | ${address_application} | ${peer_application}
-| | And Honeycomb configures BGP route
-| | ... | ${dut2_node} | ${address_application} | ${dut1_route_ip6}
-| | ... | ${dut1_route_ip6_prefix} | ${dut1_route_ip6_id} | ipv6
-| | And Sleep | 5s | Wait for route advertisement. Retry timer is 5 seconds.
-| | Then Routing data from Honeycomb should contain
-| | ... | ${dut1_node} | learned-protocol-0 | ipv6 | ${route_ip6_operational}
-| | And Routing data from Honeycomb should contain
-| | ... | ${dut2_node} | learned-protocol-0 | ipv6 | ${route_ip6_operational}
-| | And BGP Loc-RIB table should include | ${dut1_node} | ${rib_ip6_operational}
-| | And BGP Loc-RIB table should include | ${dut2_node} | ${rib_ip6_operational}
-
-#TODO: Add tests once implemented in HC:
-# IPv6 neighbor, L2VPN, L3VPN, linkstate, route reflector, and more
-
-*** Keywords ***
-| Configure IPv4 Management Interface
-| | [Documentation] | Change one of VPP's data-plane interfaces on DUT into\
-| | ... | a control-plane interface that Honeycomb can listen on. Setup IP\
-| | ... | addresses on the link, create suite variables for traffic trests, set
-| | ... | static ARP entries, then restart VPP and Honeycomb to apply changes.
-| | ...
-| | Configure path in 3-node circular topology
-| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']}
-| | ${interface}= | Get Interface Name | ${dut1_node} | ${dut1_to_tg}
-| | Set Suite Variable | ${interface}
-| | Set Suite Variable | ${tg_node}
-| | Set Suite Variable | ${dut1_node}
-| | Set Suite Variable | ${dut2_node}
-| | Set Suite Variable | ${dut1_to_tg}
-| | Stop VPP service on DUT | ${dut1_node}
-| | Stop VPP service on DUT | ${dut2_node}
-| | Stop Honeycomb Service on DUTs | ${dut1_node}
-| | Stop Honeycomb Service on DUTs | ${dut2_node}
-| | Convert data-plane interface to control-plane
-| | ... | ${dut1_node} | ${dut1_to_tg}
-| | Convert data-plane interface to control-plane
-| | ... | ${dut1_node} | ${dut1_to_dut2}
-| | Convert data-plane interface to control-plane
-| | ... | ${dut2_node} | ${dut2_to_dut1}
-| | Sleep | 5sec | Wait until OS reclaims the interfaces.
-| | ${tg_to_dut1_name}= | Get Interface Name by MAC
-| | ... | ${tg_node} | ${tg_to_dut1_mac}
-| | ${dut1_to_tg_name}= | Get Interface Name by MAC
-| | ... | ${dut1_node} | ${dut1_to_tg_mac}
-| | ${dut1_to_dut2_name}= | Get Interface Name by MAC
-| | ... | ${dut1_node} | ${dut1_to_dut2_mac}
-| | ${dut2_to_dut1_name}= | Get Interface Name by MAC
-| | ... | ${dut2_node} | ${dut2_to_dut1_mac}
-| | Set Suite Variable | ${dut1_to_tg_name}
-| | Set Suite Variable | ${tg_to_dut1_name}
-| | Set Suite Variable | ${dut1_to_dut2_name}
-| | Set Suite Variable | ${dut2_to_dut1_name}
-| | Set management interface address
-| | ... | ${tg_node} | ${tg_to_dut1_name}
-| | ... | ${tg_to_dut1_ip} | ${prefix}
-| | Set management interface address
-| | ... | ${dut1_node} | ${dut1_to_tg_name}
-| | ... | ${dut1_to_tg_ip} | ${prefix}
-| | Set management interface address
-| | ... | ${dut1_node} | ${dut1_to_dut2_name}
-| | ... | ${dut1_to_dut2_ip} | ${prefix}
-| | Set management interface address
-| | ... | ${dut2_node} | ${dut2_to_dut1_name}
-| | ... | ${dut2_to_dut1_ip} | ${prefix}
-| | Set Static ARP | ${tg_node} | ${dut1_to_tg_ip} | ${dut1_to_tg_mac}
-| | Set Static ARP | ${dut1_node} | ${tg_to_dut1_ip} | ${tg_to_dut1_mac}
-| | Set Static ARP | ${dut1_node} | ${dut2_to_dut1_ip} | ${dut2_to_dut1_mac}
-| | Set Static ARP | ${dut2_node} | ${dut1_to_dut2_ip} | ${dut1_to_dut2_mac}
-| | Enable Honeycomb Feature | ${dut2_node} | BGP
-| | Configure BGP Module | ${dut1_node} | ${dut1_to_dut2_ip}
-| | ... | ${bgp_port} | ${bgp_as_number}
-| | Configure BGP Module | ${dut2_node} | ${dut2_to_dut1_ip}
-| | ... | ${bgp_port} | ${bgp_as_number}
-| | Restart VPP service | ${dut1_node}
-| | Restart VPP service | ${dut2_node}
-| | Configure Honeycomb service on DUTs | ${dut1_node}
-| | Set Up Honeycomb Functional Test Suite | ${dut2_node}
-
-| Unconfigure IPv4 Management Interfaces
-| | [Documentation] | Remove all IP addresses from the interface.
-| | ...
-| | Clear Interface Configuration | ${tg_node} | ${tg_to_dut1_name}
-| | Clear Interface Configuration | ${dut1_node} | ${dut1_to_tg_name}
-| | Clear Interface Configuration | ${dut1_node} | ${dut1_to_dut2_name}
-| | Clear Interface Configuration | ${dut2_node} | ${dut2_to_dut1_name}
-
-| Set BGP Suite Variables
-| | Configure path in 3-node circular topology
-| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']}
-| | Set Suite Variable | ${interface}
-| | Set Suite Variable | ${tg_node}
-| | Set Suite Variable | ${dut1_node}
-| | Set Suite Variable | ${dut2_node}
-| | Set Suite Variable | ${dut1_to_tg}
-| | Set Suite Variable | ${dut1_to_tg_name}
-| | Set Suite Variable | ${tg_to_dut1_name}
-| | Set Suite Variable | ${dut1_to_dut2_name}
-| | Set Suite Variable | ${dut2_to_dut1_name}