CSIT-1037 K8s container extensions

- Add new K8S topologies on i40 based nic

Change-Id: Id20f1e15dab347edee128633230aa098b774e43d
Signed-off-by: Peter Mikus <pmikus@cisco.com>

1 files changed, 303 insertions, 0 deletions

diff --git a/tests/kubernetes/perf/container_memif/10ge2p1x710-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-ndrpdrdisc.robot b/tests/kubernetes/perf/container_memif/10ge2p1x710-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-ndrpdrdisc.robot
new file mode 100644
index 0000000000..2282a100bd
--- /dev/null
+++ b/tests/kubernetes/perf/container_memif/10ge2p1x710-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-ndrpdrdisc.robot
@@ -0,0 +1,303 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X710 | ETH | L2XCFWD | BASE | L2XCBASE | MEMIF
+| ... | K8S | 1VSWITCH | 1VNF | VPP_AGENT | SFC_CONTROLLER | PARALLEL
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X710
+| ...
+| Test Setup | Set up performance test with Ligato Kubernetes
+| ...
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Teardown | Tear down performance test with Ligato Kubernetes
+| ...
+| Documentation | *RFC2544: Pkt throughput L2XC test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross-
+| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
+| ... | VNF Container is connected to VSWITCH container via Memif interface. All
+| ... | containers is running same VPP version. Containers are deployed with
+| ... | Kubernetes. Configuration is applied by vnf-agent.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using either binary search or linear search
+| ... | algorithms with configured starting rate and final step that determines
+| ... | throughput measurement resolution. Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, 254 flows per flow-group) with all packets
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static
+| ... | payload. MAC addresses are matching MAC addresses of the TG node
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit} | ${10000000000}
+# SFC profile
+| ${sfc_profile} | configmaps/eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254
+# CPU settings
+| ${system_cpus}= | ${1}
+| ${vswitch_cpus}= | ${5}
+| ${vnf_cpus}= | ${2}
+
+*** Keywords ***
+| Create Kubernetes VSWITCH startup config on all DUTs
+| | [Documentation] | Create base startup configuration of VSWITCH in Kubernetes
+| | ... | deploy to all DUTs.
+| | ...
+| | ... | *Arguments:*
+| | ... | - ${framesize} - L2 framesize. Type: integer
+| | ... | - ${wt} - Worker threads. Type: integer
+| | ... | - ${rxq} - RX queues. Type: integer
+| | ...
+| | ... | *Example:*
+| | ...
+| | ... | \| Create Kubernetes VSWITCH startup config on all DUTs \| ${64} \
+| | ... | \| ${1} \| ${1}
+| | ...
+| | [Arguments] | ${framesize} | ${wt} | ${rxq}
+| | ${dut1_numa}= | Get interfaces numa node | ${dut1}
+| | ... | ${dut1_if1} | ${dut1_if2}
+| | ${dut2_numa}= | Get interfaces numa node | ${dut2}
+| | ... | ${dut2_if1} | ${dut2_if2}
+| | ${dut1_if1_pci}= | Get Interface PCI Addr | ${dut1} | ${dut1_if1}
+| | ${dut1_if2_pci}= | Get Interface PCI Addr | ${dut1} | ${dut1_if2}
+| | ${dut2_if1_pci}= | Get Interface PCI Addr | ${dut2} | ${dut2_if1}
+| | ${dut2_if2_pci}= | Get Interface PCI Addr | ${dut2} | ${dut2_if2}
+| | ${cpu_cnt}= | Evaluate | ${wt}+1
+| | ${config}= | Run keyword | Create Kubernetes VSWITCH startup config
+| | ... | node=${dut1} | cpu_cnt=${cpu_cnt} | cpu_node=${dut1_numa}
+| | ... | cpu_skip=${system_cpus} | smt_used=${False}
+| | ... | filename=/tmp/vswitch.conf | framesize=${framesize} | rxq=${rxq}
+| | ... | if1=${dut1_if1_pci} | if2=${dut1_if2_pci}
+| | ${config}= | Run keyword | Create Kubernetes VSWITCH startup config
+| | ... | node=${dut2} | cpu_cnt=${cpu_cnt} | cpu_node=${dut2_numa}
+| | ... | cpu_skip=${system_cpus} | smt_used=${False}
+| | ... | filename=/tmp/vswitch.conf | framesize=${framesize} | rxq=${rxq}
+| | ... | if1=${dut2_if1_pci} | if2=${dut2_if2_pci}
+
+| Create Kubernetes VNF'${i}' startup config on all DUTs
+| | [Documentation] | Create base startup configuration of VNF in Kubernetes
+| | ... | deploy to all DUTs.
+| | ...
+| | ${i_int}= | Convert To Integer | ${i}
+| | ${cpu_skip}= | Evaluate | ${vswitch_cpus}+${system_cpus}
+| | ${dut1_numa}= | Get interfaces numa node | ${dut1}
+| | ... | ${dut1_if1} | ${dut1_if2}
+| | ${dut2_numa}= | Get interfaces numa node | ${dut2}
+| | ... | ${dut2_if1} | ${dut2_if2}
+| | ${config}= | Run keyword | Create Kubernetes VNF startup config
+| | ... | node=${dut1} | cpu_cnt=${vnf_cpus} | cpu_node=${dut1_numa}
+| | ... | cpu_skip=${cpu_skip} | smt_used=${False} | filename=/tmp/vnf${i}.conf
+| | ... | i=${i_int}
+| | ${config}= | Run keyword | Create Kubernetes VNF startup config
+| | ... | node=${dut2} | cpu_cnt=${vnf_cpus} | cpu_node=${dut2_numa}
+| | ... | cpu_skip=${cpu_skip} | smt_used=${False} | filename=/tmp/vnf${i}.conf
+| | ... | i=${i_int}
+
+| L2 Cross Connect Binary Search
+| | ...
+| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} | ${search_type}
+| | ...
+| | # Test Variables required for test execution and test teardown
+| | Set Test Variable | ${framesize}
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize}
+| | Set Test Variable | ${min_rate}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_if1_name}= | Get interface name | ${dut1} | ${dut1_if1}
+| | ${dut1_if2_name}= | Get interface name | ${dut1} | ${dut1_if2}
+| | ${dut2_if1_name}= | Get interface name | ${dut2} | ${dut2_if1}
+| | ${dut2_if2_name}= | Get interface name | ${dut2} | ${dut2_if2}
+| | Create Kubernetes VSWITCH startup config on all DUTs | ${get_framesize}
+| | ... | ${wt} | ${rxq}
+| | Create Kubernetes VNF'1' startup config on all DUTs
+| | Create Kubernetes CM from file on all DUTs | ${nodes} | csit
+| | ... | name=vswitch-vpp-cfg | vpp.conf=/tmp/vswitch.conf
+| | Create Kubernetes CM from file on all DUTs | ${nodes} | csit
+| | ... | name=vnf1-vpp-cfg | vpp.conf=/tmp/vnf1.conf
+| | Apply Kubernetes resource on node | ${dut1}
+| | ... | pods/contiv-vnf.yaml | $$VNF$$=vnf1
+| | Apply Kubernetes resource on node | ${dut2}
+| | ... | pods/contiv-vnf.yaml | $$VNF$$=vnf1
+| | Apply Kubernetes resource on node | ${dut1}
+| | ... | ${sfc_profile}.yaml | $$TEST_NAME$$=${TEST NAME}
+| | ... | $$VSWITCH_IF1$$=${dut1_if1_name}
+| | ... | $$VSWITCH_IF2$$=${dut1_if2_name}
+| | Apply Kubernetes resource on node | ${dut2}
+| | ... | ${sfc_profile}.yaml | $$TEST_NAME$$=${TEST NAME}
+| | ... | $$VSWITCH_IF1$$=${dut2_if1_name}
+| | ... | $$VSWITCH_IF2$$=${dut2_if2_name}
+| | Wait for Kubernetes PODs on all DUTs | ${nodes} | csit
+| | Set Kubernetes PODs affinity on all DUTs | ${nodes}
+| | Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=${64} | min_rate=${50000} | wt=1 | rxq=1 | search_type=NDR
+
+| tc02-64B-1t1-ceth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=${64} | min_rate=${50000} | wt=1 | rxq=1 | search_type=PDR
+
+| tc03-IMIX-1t1c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps.
+| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B)
+| | ...
+| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=IMIX_v4_1 | min_rate=${50000} | wt=1 | rxq=1 | search_type=NDR
+
+| tc04-IMIX-1t1c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for IMIX_v4_1 frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps, LT=0.5%.
+| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B)
+| | ...
+| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=IMIX_v4_1 | min_rate=${50000} | wt=1 | rxq=1 | search_type=PDR
+
+| tc05-1518B-1t1c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps.
+| | ...
+| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=${1518} | min_rate=${50000} | wt=1 | rxq=1 | search_type=NDR
+
+| tc06-1518B-1t1c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=${1518} | min_rate=${50000} | wt=1 | rxq=1 | search_type=PDR
+
+| tc07-64B-2t2c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=${64} | min_rate=${50000} | wt=2 | rxq=1 | search_type=NDR
+
+| tc08-64B-2t2c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=${64} | min_rate=${50000} | wt=2 | rxq=1 | search_type=PDR
+
+| tc09-IMIX-2t2c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps.
+| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B)
+| | ...
+| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=IMIX_v4_1 | min_rate=${50000} | wt=2 | rxq=1 | search_type=NDR
+
+| tc10-IMIX-2t2c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for IMIX_v4_1 frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps, LT=0.5%.
+| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B)
+| | ...
+| | [Tags] | IMIX | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=IMIX_v4_1 | min_rate=${50000} | wt=2 | rxq=1 | search_type=PDR
+
+| tc11-1518B-2t2c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps.
+| | ...
+| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=${1518} | min_rate=${50000} | wt=2 | rxq=1 | search_type=NDR
+
+| tc12-1518B-2t2c-eth-1drcl2xcbase-eth-2memif-1drcl2xc-1paral-k8s-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 50kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | [Template] | L2 Cross Connect Binary Search
+| | framesize=${1518} | min_rate=${50000} | wt=2 | rxq=1 | search_type=PDR