CSIT-469 Rename performance suites

Rename performance suites and add more TAGS

Change-Id: I6a5251bb6e380fe2a47a6ec1c1aeb4a9f70c5ce3
Signed-off-by: pmikus <pmikus@cisco.com>

1 files changed, 499 insertions, 0 deletions

diff --git a/tests/perf/10ge2p1x520-ethip6-ip6scale2m-ndrdisc.robot b/tests/perf/10ge2p1x520-ethip6-ip6scale2m-ndrdisc.robot
new file mode 100644
index 0000000000..7b5b137c07
--- /dev/null
+++ b/tests/perf/10ge2p1x520-ethip6-ip6scale2m-ndrdisc.robot
@@ -0,0 +1,499 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance.robot
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_LONG
+| ...        | FIB_2M | NIC_Intel-X520-DA2 | PERFTEST_SCALE
+| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | 3-node Performance Suite Teardown
+| Test Setup | Setup all DUTs before test
+| Test Teardown | Run Keywords
+| ...           | Run Keyword If Test Failed
+| ...           | Traffic should pass with no loss | 10
+| ...           | ${min_rate}pps | ${framesize} | 3-node-IPv6-dst-${rts_per_flow}
+| ...           | fail_on_loss=${False}
+| ...           | AND | Remove startup configuration of VPP from all DUTs
+| Documentation | *RFC2544: Pkt throughput IPv6 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6
+| ... | routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using either binary search or linear search
+| ... | algorithms with configured starting rate and final step that determines
+| ... | throughput measurement resolution. Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, 1M flows per flow-group) with all packets
+| ... | containing Ethernet header, IPv6 header withq IP and static payload.
+| ... | MAC addresses are matching MAC addresses of the TG node interfaces.
+| ... | Incrementing of IP.dst (IPv6 destination address) field is applied to
+| ... | both streams.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+#X520-DA2 bandwidth limit
+| ${s_limit} | ${10000000000}
+| ${rts_per_flow}= | ${1000000}
+
+*** Test Cases ***
+| TC01: 78B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| TC02: 78B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${glob_loss_acceptance}
+| | ...                                       | ${glob_loss_acceptance_type}
+
+| TC03: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| TC04: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${glob_loss_acceptance}
+| | ...                                       | ${glob_loss_acceptance_type}
+
+| TC05: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| TC06: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${glob_loss_acceptance}
+| | ...                                       | ${glob_loss_acceptance_type}
+
+| TC07: 78B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| TC08: 78B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${glob_loss_acceptance}
+| | ...                                       | ${glob_loss_acceptance_type}
+
+| TC09: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| TC10: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${glob_loss_acceptance}
+| | ...                                       | ${glob_loss_acceptance_type}
+
+| TC11: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| TC12: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${glob_loss_acceptance}
+| | ...                                       | ${glob_loss_acceptance_type}
+
+| TC13: 78B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| TC14: 78B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${glob_loss_acceptance}
+| | ...                                       | ${glob_loss_acceptance_type}
+
+| TC15: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| TC16: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${glob_loss_acceptance}
+| | ...                                       | ${glob_loss_acceptance_type}
+
+| TC17: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| TC18: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | And   Scale IPv6 forwarding initialized in a 3-node circular topology
+| | ...   | ${rts_per_flow}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max}
+| | ...                                       | 3-node-IPv6-dst-${rts_per_flow}
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${glob_loss_acceptance}
+| | ...                                       | ${glob_loss_acceptance_type}