CSIT-469 Rename performance suites

Rename performance suites and add more TAGS

Change-Id: I6a5251bb6e380fe2a47a6ec1c1aeb4a9f70c5ce3
Signed-off-by: pmikus <pmikus@cisco.com>

1 files changed, 0 insertions, 194 deletions

diff --git a/tests/perf/Short_IPv6_Intel-X520-DA2.robot b/tests/perf/Short_IPv6_Intel-X520-DA2.robot
deleted file mode 100644
index 62442c7487..0000000000
--- a/tests/perf/Short_IPv6_Intel-X520-DA2.robot
+++ /dev/null
@@ -1,194 +0,0 @@
-# Copyright (c) 2016 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance.robot
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_SHORT
-| ...        | NIC_Intel-X520-DA2
-| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
-| ... | L3 | Intel-X520-DA2
-
-| Suite Teardown | 3-node Performance Suite Teardown
-| Test Setup | Setup all DUTs before test
-| Test Teardown | Run Keywords | Remove startup configuration of VPP from all DUTs
-| ...           | AND          | Show vpp trace dump on all DUTs
-| Documentation | *Reference NDR throughput IPv6 routing verify test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6
-| ... | routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with
-| ... | 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* In short performance tests, TG verifies
-| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet
-| ... | loss tolerance. Ref-NDR value is periodically updated acording to
-| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long
-| ... | performance tests for the same DUT configuration. Test packets are
-| ... | generated by TG on links to DUTs. TG traffic profile contains two L3
-| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with
-| ... | all packets containing Ethernet header, IPv6 header and static
-| ... | payload. MAC addresses are matching MAC addresses of the TG node
-| ... | interfaces.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Test Cases ***
-| TC01: Verify 78B ref-NDR at 2x 2.9Mpps - DUT IPv6 - 1thread 1core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte
-| | ... | frames using single trial throughput test.
-| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
-| | ${framesize}= | Set Variable | 78
-| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 2.9mpps
-| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
-| | And   Add PCI devices to DUTs from 3-node single link topology
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | And   IPv6 forwarding initialized in a 3-node circular topology
-| | Then  Traffic should pass with no loss | ${duration} | ${rate}
-| | ...                                    | ${framesize} | 3-node-IPv6
-
-| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 - 1thread 1core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
-| | ... | frames using single trial throughput test.
-| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
-| | ${framesize}= | Set Variable | 1518
-| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 812743pps
-| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
-| | And   Add PCI devices to DUTs from 3-node single link topology
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | And   IPv6 forwarding initialized in a 3-node circular topology
-| | Then  Traffic should pass with no loss | ${duration} | ${rate}
-| | ...                                    | ${framesize} | 3-node-IPv6
-
-| TC03: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 - 1thread 1core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
-| | ... | frames using single trial throughput test.
-| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
-| | ${framesize}= | Set Variable | 9000
-| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 138580pps
-| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
-| | And   Add PCI devices to DUTs from 3-node single link topology
-| | And   Apply startup configuration on all VPP DUTs
-| | And   IPv6 forwarding initialized in a 3-node circular topology
-| | Then  Traffic should pass with no loss | ${duration} | ${rate}
-| | ...                                    | ${framesize} | 3-node-IPv6
-
-| TC04: Verify 78B ref-NDR at 2x 5.9Mpps - DUT IPv6 - 2thread 2core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte
-| | ... | frames using single trial throughput test.
-| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
-| | ${framesize}= | Set Variable | 78
-| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 5.9mpps
-| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
-| | And   Add PCI devices to DUTs from 3-node single link topology
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | And   IPv6 forwarding initialized in a 3-node circular topology
-| | Then  Traffic should pass with no loss | ${duration} | ${rate}
-| | ...                                    | ${framesize} | 3-node-IPv6
-
-| TC05: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 - 2thread 2core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
-| | ... | frames using single trial throughput test.
-| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
-| | ${framesize}= | Set Variable | 1518
-| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 812743pps
-| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
-| | And   Add PCI devices to DUTs from 3-node single link topology
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | And   IPv6 forwarding initialized in a 3-node circular topology
-| | Then  Traffic should pass with no loss | ${duration} | ${rate}
-| | ...                                    | ${framesize} | 3-node-IPv6
-
-| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 - 2thread 2core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
-| | ... | frames using single trial throughput test.
-| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
-| | ${framesize}= | Set Variable | 9000
-| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 138580pps
-| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
-| | And   Add PCI devices to DUTs from 3-node single link topology
-| | And   Apply startup configuration on all VPP DUTs
-| | And   IPv6 forwarding initialized in a 3-node circular topology
-| | Then  Traffic should pass with no loss | ${duration} | ${rate}
-| | ...                                    | ${framesize} | 3-node-IPv6
-
-| TC07: Verify 78B ref-NDR at 2x 7.3Mpps - DUT IPv6 - 4thread 4core 2rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
-| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 78 Byte
-| | ... | frames using single trial throughput test.
-| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
-| | ${framesize}= | Set Variable | 78
-| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 7.3mpps
-| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
-| | And   Add PCI devices to DUTs from 3-node single link topology
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | And   IPv6 forwarding initialized in a 3-node circular topology
-| | Then  Traffic should pass with no loss | ${duration} | ${rate}
-| | ...                                    | ${framesize} | 3-node-IPv6
-
-| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 - 4thread 4core 2rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
-| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte
-| | ... | frames using single trial throughput test.
-| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
-| | ${framesize}= | Set Variable | 1518
-| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 812743pps
-| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
-| | And   Add PCI devices to DUTs from 3-node single link topology
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | And   IPv6 forwarding initialized in a 3-node circular topology
-| | Then  Traffic should pass with no loss | ${duration} | ${rate}
-| | ...                                    | ${framesize} | 3-node-IPv6
-
-| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 - 4thread 4core 2rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \
-| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte
-| | ... | frames using single trial throughput test.
-| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
-| | ${framesize}= | Set Variable | 9000
-| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 138580pps
-| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
-| | And   Add PCI devices to DUTs from 3-node single link topology
-| | And   Apply startup configuration on all VPP DUTs
-| | And   IPv6 forwarding initialized in a 3-node circular topology
-| | Then  Traffic should pass with no loss | ${duration} | ${rate}
-| | ...                                    | ${framesize} | 3-node-IPv6