Add library for set path variables for testing.

Change-Id: Icb243bacc9329c4bf3bc28098fced473b4e3c991
Signed-off-by: Matej Klotton <mklotton@cisco.com>

1 files changed, 58 insertions, 46 deletions

diff --git a/tests/suites/ipv6/ipv6_iacl_untagged.robot b/tests/suites/ipv6/ipv6_iacl_untagged.robot
index 24a408b9be..ed91616653 100644
--- a/tests/suites/ipv6/ipv6_iacl_untagged.robot
+++ b/tests/suites/ipv6/ipv6_iacl_untagged.robot
@@ -15,7 +15,7 @@
 | Resource | resources/libraries/robot/default.robot
 | Resource | resources/libraries/robot/counters.robot
 | Resource | resources/libraries/robot/interfaces.robot
-| Resource | resources/libraries/robot/iacl.robot
+| Resource | resources/libraries/robot/testing_path.robot
 | Resource | resources/libraries/robot/ipv6.robot
 | Resource | resources/libraries/robot/l2_xconnect.robot
 | Resource | resources/libraries/robot/traffic.robot
@@ -29,11 +29,11 @@
 | Test Teardown | Show packet trace on all DUTs | ${nodes}
 
 *** Variables ***
-| ${dut1_if1_ip}= | 3ffe:62::1
-| ${dut1_if2_ip}= | 3ffe:63::1
-| ${dut1_if2_ip_GW}= | 3ffe:63::2
-| ${dut2_if1_ip}= | 3ffe:72::1
-| ${dut2_if2_ip}= | 3ffe:73::1
+| ${dut1_to_tg_ip}= | 3ffe:62::1
+| ${dut1_to_dut2_ip}= | 3ffe:63::1
+| ${dut1_to_dut2_ip_GW}= | 3ffe:63::2
+| ${dut2_to_dut1_ip}= | 3ffe:72::1
+| ${dut2_to_tg_ip}= | 3ffe:73::1
 | ${test_dst_ip}= | 3ffe:64::1
 | ${test_src_ip}= | 3ffe:61::1
 | ${prefix_length}= | 64
@@ -43,68 +43,77 @@
 | | [Documentation] | Create classify table on VPP, add source IP address
 | | ...             | of traffic into table and setup 'deny' traffic
 | | ...             | and check if traffic is dropped.
-| | Given Node path computed for 3-node topology
+| | Given Path for 3-node testing is set
 | | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']}
-| | And Interfaces in path are up
-| | And IPv6 Addresses set on the node interfaces
-| | ... | ${dut1_node} | ${dut1_if1} | ${dut1_if1_ip} | ${dut1_if2}
-| | ... | ${dut1_if2_ip} | ${prefix_length}
+| | And Interfaces in 3-node path are up
+| | And Vpp Set If Ipv6 Addr | ${dut1_node}
+| | ... | ${dut1_to_tg} | ${dut1_to_tg_ip} | ${prefix_length}
+| | And Vpp Set If Ipv6 Addr  | ${dut1_node}
+| | ... | ${dut1_to_dut2} | ${dut1_to_dut2_ip} | ${prefix_length}
 | | ${table_index} | ${skip_n} | ${match_n}= | When Vpp Create Classify Table
 | | ... | ${dut1_node} | ip6 | src
 | | And Vpp Configure Classify Session
 | | ... | ${dut1_node} | deny | ${table_index} | ${skip_n} | ${match_n}
 | | ... | ip6 | src | ${test_src_ip}
 | | And Vpp Enable Input Acl Interface
-| | ... | ${dut1_node} | ${dut1_if1} | ip6 | ${table_index}
+| | ... | ${dut1_node} | ${dut1_to_tg} | ip6 | ${table_index}
 | | And Add Ip Neighbor
-| | ... | ${dut1_node} | ${dut1_if2} | ${dut1_if2_ip_GW} | ${tg_if2_mac}
+| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut1_to_dut2_ip_GW}
+| | ... | ${tg_to_dut2_mac}
 | | And Vpp Route Add
-| | ... | ${dut1_node} | ${test_dst_ip} | ${prefix_length} | ${dut1_if2_ip_GW}
-| | ... | ${dut1_if2}
-| | And L2 setup xconnect on DUT | ${dut2_node} | ${dut2_if1} | ${dut2_if2}
-| | Then Send packet from Port to Port should failed | ${tg_node} |
-| | ... | ${test_src_ip} | ${test_dst_ip} | ${tg_if1} | ${tg_if1_mac} |
-| | ... | ${dut1_if1_mac} | ${tg_if2} | ${dut1_if2_mac} | ${tg_if2_mac}
+| | ... | ${dut1_node} | ${test_dst_ip} | ${prefix_length}
+| | ... | ${dut1_to_dut2_ip_GW} | ${dut1_to_dut2}
+| | And L2 setup xconnect on DUT
+| | ... | ${dut2_node} | ${dut2_to_dut1} | ${dut2_to_tg}
+| | Then Send packet from Port to Port should failed | ${tg_node}
+| | ... | ${test_src_ip} | ${test_dst_ip} | ${tg_to_dut1} | ${tg_to_dut1_mac}
+| | ... | ${dut1_to_tg_mac} | ${tg_to_dut2}
+| | ... | ${dut1_to_dut2_mac} | ${tg_to_dut2_mac}
 
 
 | VPP drops packets based on IPv6 destination addresses
 | | [Documentation] | Create classify table on VPP, add destination IP address
 | | ...             | of traffic into table and setup 'deny' traffic
 | | ...             | and check if traffic is dropped.
-| | Given Node path computed for 3-node topology
+| | Given Path for 3-node testing is set
 | | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']}
-| | And Interfaces in path are up
-| | And IPv6 Addresses set on the node interfaces
-| | ... | ${dut1_node} | ${dut1_if1} | ${dut1_if1_ip} | ${dut1_if2}
-| | ... | ${dut1_if2_ip} | ${prefix_length}
+| | And Interfaces in 3-node path are up
+| | And Vpp Set If Ipv6 Addr | ${dut1_node}
+| | ... | ${dut1_to_tg} | ${dut1_to_tg_ip} | ${prefix_length}
+| | And Vpp Set If Ipv6 Addr  | ${dut1_node}
+| | ... | ${dut1_to_dut2} | ${dut1_to_dut2_ip} | ${prefix_length}
 | | ${table_index} | ${skip_n} | ${match_n}= | When Vpp Create Classify Table
 | | ... | ${dut1_node} | ip6 | dst
 | | And Vpp Configure Classify Session
 | | ... | ${dut1_node} | deny | ${table_index} | ${skip_n} | ${match_n}
 | | ... | ip6 | dst | ${test_dst_ip}
 | | And Vpp Enable Input Acl Interface
-| | ... | ${dut1_node} | ${dut1_if1} | ip6 | ${table_index}
+| | ... | ${dut1_node} | ${dut1_to_tg} | ip6 | ${table_index}
 | | And Add Ip Neighbor
-| | ... | ${dut1_node} | ${dut1_if2} | ${dut1_if2_ip_GW} | ${tg_if2_mac}
+| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut1_to_dut2_ip_GW}
+| | ... | ${tg_to_dut2_mac}
 | | And Vpp Route Add
-| | ... | ${dut1_node} | ${test_dst_ip} | ${prefix_length} | ${dut1_if2_ip_GW}
-| | ... | ${dut1_if2}
-| | And L2 setup xconnect on DUT | ${dut2_node} | ${dut2_if1} | ${dut2_if2}
-| | Then Send packet from Port to Port should failed | ${tg_node} |
-| | ... | ${test_src_ip} | ${test_dst_ip} | ${tg_if1} | ${tg_if1_mac} |
-| | ... | ${dut1_if1_mac} | ${tg_if2} | ${dut1_if2_mac} | ${tg_if2_mac}
+| | ... | ${dut1_node} | ${test_dst_ip} | ${prefix_length}
+| | ... | ${dut1_to_dut2_ip_GW} | ${dut1_to_dut2}
+| | And L2 setup xconnect on DUT
+| | ... | ${dut2_node} | ${dut2_to_dut1} | ${dut2_to_tg}
+| | Then Send packet from Port to Port should failed | ${tg_node}
+| | ... | ${test_src_ip} | ${test_dst_ip} | ${tg_to_dut1} | ${tg_to_dut1_mac}
+| | ... | ${dut1_to_tg_mac} | ${tg_to_dut2}
+| | ... | ${dut1_to_dut2_mac} | ${tg_to_dut2_mac}
 
 
 | VPP drops packets based on IPv6 src-addr and dst-addr
 | | [Documentation] | Create classify table on VPP, add source and destination
 | | ...             | IP address of traffic into table and setup 'deny' traffic
 | | ...             | and check if traffic is dropped.
-| | Given Node path computed for 3-node topology
+| | Given Path for 3-node testing is set
 | | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']}
-| | And Interfaces in path are up
-| | And IPv6 Addresses set on the node interfaces
-| | ... | ${dut1_node} | ${dut1_if1} | ${dut1_if1_ip} | ${dut1_if2}
-| | ... | ${dut1_if2_ip} | ${prefix_length}
+| | And Interfaces in 3-node path are up
+| | And Vpp Set If Ipv6 Addr | ${dut1_node}
+| | ... | ${dut1_to_tg} | ${dut1_to_tg_ip} | ${prefix_length}
+| | And Vpp Set If Ipv6 Addr  | ${dut1_node}
+| | ... | ${dut1_to_dut2} | ${dut1_to_dut2_ip} | ${prefix_length}
 | | ${table_index_1} | ${skip_n_1} | ${match_n_1}=
 | | ... | When Vpp Create Classify Table | ${dut1_node} | ip6 | src
 | | ${table_index_2} | ${skip_n_2} | ${match_n_2}=
@@ -116,15 +125,18 @@
 | | ... | ${dut1_node} | deny | ${table_index_2} | ${skip_n_2} | ${match_n_2}
 | | ... | ip6 | dst | ${test_dst_ip}
 | | And Vpp Enable Input Acl Interface
-| | ... | ${dut1_node} | ${dut1_if1} | ip6 | ${table_index_1}
+| | ... | ${dut1_node} | ${dut1_to_tg} | ip6 | ${table_index_1}
 | | And Vpp Enable Input Acl Interface
-| | ... | ${dut1_node} | ${dut1_if1} | ip6 | ${table_index_2}
+| | ... | ${dut1_node} | ${dut1_to_tg} | ip6 | ${table_index_2}
 | | And Add Ip Neighbor
-| | ... | ${dut1_node} | ${dut1_if2} | ${dut1_if2_ip_GW} | ${tg_if2_mac}
+| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut1_to_dut2_ip_GW}
+| | ... | ${tg_to_dut2_mac}
 | | And Vpp Route Add
-| | ... | ${dut1_node} | ${test_dst_ip} | ${prefix_length} | ${dut1_if2_ip_GW}
-| | ... | ${dut1_if2}
-| | And L2 setup xconnect on DUT | ${dut2_node} | ${dut2_if1} | ${dut2_if2}
-| | Then Send packet from Port to Port should failed | ${tg_node} |
-| | ... | ${test_src_ip} | ${test_dst_ip} | ${tg_if1} | ${tg_if1_mac} |
-| | ... | ${dut1_if1_mac} | ${tg_if2} | ${dut1_if2_mac} | ${tg_if2_mac}
+| | ... | ${dut1_node} | ${test_dst_ip} | ${prefix_length}
+| | ... | ${dut1_to_dut2_ip_GW} | ${dut1_to_dut2}
+| | And L2 setup xconnect on DUT
+| | ... | ${dut2_node} | ${dut2_to_dut1} | ${dut2_to_tg}
+| | Then Send packet from Port to Port should failed | ${tg_node}
+| | ... | ${test_src_ip} | ${test_dst_ip} | ${tg_to_dut1} | ${tg_to_dut1_mac}
+| | ... | ${dut1_to_tg_mac} | ${tg_to_dut2}
+| | ... | ${dut1_to_dut2_mac} | ${tg_to_dut2_mac}