Suite: performance.

Files: Long_IPv4_Intel-X520-DA2.robot, Long_IPv4_Cop_Intel-X520-DA2.robot,
Long_Bridge_Domain_Intel-X520-DA2.robot,
Long_Xconnect_Intel-X520-DA2.robot, Long_Xconnect_Dot1q_Intel-X520-DA2.robot,
Long_IPv6_Intel-X520-DA2.robot, Long_IPv6_Cop_Intel-X520-DA2.robot.
Updated test cases names and test cases documentation.

Change-Id: I83262881a4b56512975c8ecc4518ddd2d7ec54b3
Signed-off-by: Maciek Konstantynowicz <mkonstan@cisco.com>

1 files changed, 92 insertions, 69 deletions

diff --git a/tests/suites/performance/Long_IPv4_Intel-X520-DA2.robot b/tests/suites/performance/Long_IPv4_Intel-X520-DA2.robot
index 8b80aabcff..16e1797a82 100644
--- a/tests/suites/performance/Long_IPv4_Intel-X520-DA2.robot
+++ b/tests/suites/performance/Long_IPv4_Intel-X520-DA2.robot
@@ -25,19 +25,34 @@
 | Suite Teardown | 3-node Performance Suite Teardown
 | Test Setup | Setup all DUTs before test
 | Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs
-| Documentation | *Throughput search suite (based on RFC2544).*
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
 | ...
-| ... | Test suite uses 3-node topology TG - DUT1 - DUT2 - TG, with one link
-| ... | between nodes. Traffic profile contain 2 L3 streams (1 stream per
-| ... | direction). Packets contain Ethernet header, IPv4 header,
-| ... | IP protocol=61 and random payload. Ethernet header MAC addresses are
-| ... | matching MAC addresses of the TG node.
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with
+| ... | 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using either binary search or linear search
+| ... | algorithms with configured starting rate and final step that determines
+| ... | throughput measurement resolution. Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static
+| ... | payload. MAC addresses are matching MAC addresses of the TG node
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Test Cases ***
-| Find NDR by using RFC2544 binary search and 64B frames through IPv4 forwarding in 3-node topology
+| TC01: 64B NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 | | [Documentation]
-| | ... | Find throughput with non drop rate for 64B frames by using
-| | ... | binary search with threshold 0.1Mpps.
+| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps.
 | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
 | | ${framesize}= | Set Variable | 64
 | | ${min_rate}= | Set Variable | 100000
@@ -55,11 +70,11 @@
 | | ...                                       | ${min_rate} | ${max_rate}
 | | ...                                       | ${threshold}
 
-| Find PDR by using RFC2544 binary search and 64B frames through IPv4 forwarding in 3-node topology
+| TC02: 64B PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 | | [Documentation]
-| | ... | Find throughput with partial drop rate for 64B frames by using
-| | ... | binary search with threshold 0.1Mpps. Loss acceptance is set to 0.5
-| | ... | percent of transmitted packets.
+| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR
 | | ${framesize}= | Set Variable | 64
 | | ${min_rate}= | Set Variable | 100000
@@ -79,10 +94,11 @@
 | | ...                                       | ${glob_loss_acceptance}
 | | ...                                       | ${glob_loss_acceptance_type}
 
-| Find NDR by using RFC2544 binary search and 1518B frames through IPv4 forwarding in 3-node topology
+| TC03: 1518B NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 | | [Documentation]
-| | ... | Find throughput with non drop rate for 1518B frames by using
-| | ... | binary search with threshold 10,000pps.
+| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps.
 | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
 | | ${framesize}= | Set Variable | 1518
 | | ${min_rate}= | Set Variable | 10000
@@ -100,11 +116,11 @@
 | | ...                                       | ${min_rate} | ${max_rate}
 | | ...                                       | ${threshold}
 
-| Find PDR by using RFC2544 binary search and 1518B frames through IPv4 forwarding in 3-node topology
+| TC04: 1518B PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 | | [Documentation]
-| | ... | Find throughput with partial drop rate for 1518B frames by using
-| | ... | binary search with threshold 10,000pps. Loss acceptance is set to 0.5
-| | ... | percent of transmitted packets.
+| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR
 | | ${framesize}= | Set Variable | 1518
 | | ${min_rate}= | Set Variable | 10000
@@ -124,10 +140,11 @@
 | | ...                                       | ${glob_loss_acceptance}
 | | ...                                       | ${glob_loss_acceptance_type}
 
-| Find NDR by using RFC2544 binary search and 9000B frames through IPv4 forwarding in 3-node topology
+| TC05: 9000B NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 | | [Documentation]
-| | ... | Find throughput with non drop rate for 9000B frames by using
-| | ... | binary search with threshold 5,000pps.
+| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps.
 | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
 | | ${framesize}= | Set Variable | 9000
 | | ${min_rate}= | Set Variable | 5000
@@ -144,11 +161,11 @@
 | | ...                                       | ${min_rate} | ${max_rate}
 | | ...                                       | ${threshold}
 
-| Find PDR by using RFC2544 binary search and 9000B frames through IPv4 forwarding in 3-node topology
+| TC06: 9000B PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 | | [Documentation]
-| | ... | Find throughput with partial drop rate for 9000B frames by using
-| | ... | binary search with threshold of 5,000pps. Loss acceptance is set to
-| | ... | 0.5 percent of transmitted packets.
+| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR
 | | ${framesize}= | Set Variable | 9000
 | | ${min_rate}= | Set Variable | 5000
@@ -167,10 +184,11 @@
 | | ...                                       | ${glob_loss_acceptance}
 | | ...                                       | ${glob_loss_acceptance_type}
 
-| Find NDR with 2 cores and rxqueues 1 by using RFC2544 binary search and 64B frames through IPv4 forwarding in 3-node topology
+| TC07: 64B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 | | [Documentation]
-| | ... | Find throughput on 2 cores with non drop rate for 64B frames by using
-| | ... | binary search with threshold 0.1Mpps.
+| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps.
 | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
 | | ${framesize}= | Set Variable | 64
 | | ${min_rate}= | Set Variable | 100000
@@ -188,11 +206,11 @@
 | | ...                                       | ${min_rate} | ${max_rate}
 | | ...                                       | ${threshold}
 
-| Find PDR with 2 cores and rxqueues 1 by using RFC2544 binary search and 64B frames through IPv4 forwarding in 3-node topology
+| TC08: 64B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 | | [Documentation]
-| | ... | Find throughput on 2 cores with partial drop rate for 64B frames by
-| | ... | using binary search with threshold 0.1Mpps. Loss acceptance is set to
-| | ... | 0.5 percent of transmitted packets.
+| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR
 | | ${framesize}= | Set Variable | 64
 | | ${min_rate}= | Set Variable | 100000
@@ -212,10 +230,11 @@
 | | ...                                       | ${glob_loss_acceptance}
 | | ...                                       | ${glob_loss_acceptance_type}
 
-| Find NDR with 2 cores and rxqueues 1 by using RFC2544 binary search and 1518B frames through IPv4 forwarding in 3-node topology
+| TC09: 1518B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 | | [Documentation]
-| | ... | Find throughput on 2 cores with non drop rate for 1518B frames by
-| | ... | using binary search with threshold 10,000pps.
+| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps.
 | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
 | | ${framesize}= | Set Variable | 1518
 | | ${min_rate}= | Set Variable | 10000
@@ -233,11 +252,11 @@
 | | ...                                       | ${min_rate} | ${max_rate}
 | | ...                                       | ${threshold}
 
-| Find PDR with 2 cores and rxqueues 1 by using RFC2544 binary search and 1518B frames through IPv4 forwarding in 3-node topology
+| TC10: 1518B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 | | [Documentation]
-| | ... | Find throughput on 2 cores with partial drop rate for 1518B frames by
-| | ... | using binary search with threshold 10,000pps. Loss acceptance is set
-| | ... | to 0.5 percent of transmitted packets.
+| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR
 | | ${framesize}= | Set Variable | 1518
 | | ${min_rate}= | Set Variable | 10000
@@ -257,10 +276,11 @@
 | | ...                                       | ${glob_loss_acceptance}
 | | ...                                       | ${glob_loss_acceptance_type}
 
-| Find NDR with 2 cores and rxqueues 1 by using RFC2544 binary search and 9000B frames through IPv4 forwarding in 3-node topology
+| TC11: 9000B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 | | [Documentation]
-| | ... | Find throughput on 2 cores with non drop rate for 9000B frames by
-| | ... | using binary search with threshold 5,000pps.
+| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps.
 | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
 | | ${framesize}= | Set Variable | 9000
 | | ${min_rate}= | Set Variable | 5000
@@ -277,11 +297,11 @@
 | | ...                                       | ${min_rate} | ${max_rate}
 | | ...                                       | ${threshold}
 
-| Find PDR with 2 cores and rxqueues 1 by using RFC2544 binary search and 9000B frames through IPv4 forwarding in 3-node topology
+| TC12: 9000B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 | | [Documentation]
-| | ... | Find throughput on 2 cores with partial drop rate for 9000B frames by
-| | ... | using binary search with threshold 5,000pps. Loss acceptance is set
-| | ... | to 0.5 percent of transmitted packets.
+| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR
 | | ${framesize}= | Set Variable | 9000
 | | ${min_rate}= | Set Variable | 5000
@@ -300,10 +320,11 @@
 | | ...                                       | ${glob_loss_acceptance}
 | | ...                                       | ${glob_loss_acceptance_type}
 
-| Find NDR with 4 cores and rxqueues 2 by using RFC2544 binary search and 64B frames through IPv4 forwarding in 3-node topology
+| TC13: 64B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 | | [Documentation]
-| | ... | Find throughput on 4 cores and rxqueues 2 with non drop rate for 64B
-| | ... | frames by using binary search with threshold 0.1Mpps.
+| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps.
 | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
 | | ${framesize}= | Set Variable | 64
 | | ${min_rate}= | Set Variable | 100000
@@ -321,11 +342,11 @@
 | | ...                                       | ${min_rate} | ${max_rate}
 | | ...                                       | ${threshold}
 
-| Find PDR with 4 cores and rxqueues 2 by using RFC2544 binary search and 64B frames through IPv4 forwarding in 3-node topology
+| TC14: 64B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 | | [Documentation]
-| | ... | Find throughput on 4 cores and rxqueues 2 with partial drop rate for 64B
-| | ... | frames by using binary search with threshold 0.1Mpps. Loss acceptance
-| | ... | is set to 0.5 percent of transmitted packets.
+| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames
+| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR
 | | ${framesize}= | Set Variable | 64
 | | ${min_rate}= | Set Variable | 100000
@@ -345,10 +366,11 @@
 | | ...                                       | ${glob_loss_acceptance}
 | | ...                                       | ${glob_loss_acceptance_type}
 
-| Find NDR with 4 cores and rxqueues 2 by using RFC2544 binary search and 1518B frames through IPv4 forwarding in 3-node topology
+| TC15: 1518B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 | | [Documentation]
-| | ... | Find throughput on 4 cores and rxqueues 2 with non drop rate for 1518B
-| | ... | frames by using binary search with threshold 10,000pps.
+| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps.
 | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
 | | ${framesize}= | Set Variable | 1518
 | | ${min_rate}= | Set Variable | 10000
@@ -366,11 +388,11 @@
 | | ...                                       | ${min_rate} | ${max_rate}
 | | ...                                       | ${threshold}
 
-| Find PDR with 4 cores and rxqueues 2 by using RFC2544 binary search and 1518B frames through IPv4 forwarding in 3-node topology
+| TC16: 1518B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 | | [Documentation]
-| | ... | Find throughput on 4 cores and rxqueues 2 with partial drop rate for 1518B
-| | ... | frames by using binary search with threshold 10,000pps. Loss
-| | ... | acceptance is set to 0.5 percent of transmitted packets.
+| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames
+| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR
 | | ${framesize}= | Set Variable | 1518
 | | ${min_rate}= | Set Variable | 10000
@@ -390,10 +412,11 @@
 | | ...                                       | ${glob_loss_acceptance}
 | | ...                                       | ${glob_loss_acceptance_type}
 
-| Find NDR with 4 cores and rxqueues 2 by using RFC2544 linear search and 9000B frames through IPv4 forwarding in 3-node topology
+| TC17: 9000B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 | | [Documentation]
-| | ... | Find throughput on 4 cores and rxqueues 2 with non drop rate for 9000B
-| | ... | frames by using binary search with threshold 5,000pps.
+| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps.
 | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
 | | ${framesize}= | Set Variable | 9000
 | | ${min_rate}= | Set Variable | 5000
@@ -410,11 +433,11 @@
 | | ...                                       | ${min_rate} | ${max_rate}
 | | ...                                       | ${threshold}
 
-| Find PDR with 4 cores and rxqueues 2 by using RFC2544 linear search and 9000B frames through IPv4 forwarding in 3-node topology
+| TC18: 9000B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 | | [Documentation]
-| | ... | Find throughput on 4 cores and rxqueues 2 with partial drop rate for 9000B
-| | ... | frames by using binary search with threshold 5,000pps. Loss
-| | ... | acceptance is set to 0.5 percent of transmitted packets.
+| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames
+| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR
 | | ${framesize}= | Set Variable | 9000
 | | ${min_rate}= | Set Variable | 5000