VPP_Device - add baseline tests - part IIb)

CSIT-1372

Add following baseline tests to VPP_Device:
- ip4
  eth2p-ethip4-ip4base-eth-2memif-1dcr-dev

- ip6
  eth2p-ethip6-ip6base-eth-2memif-1dcr-dev

- l2bd
  eth2p-eth-l2bdbasemaclrn-eth-2memif-1dcr-dev

- l2xc
  eth2p-eth-l2xcbase-eth-2memif-1dcr-dev

Change-Id: Ic4a3a01b62d800c528a9c9371891dcc26b875220
Signed-off-by: Jan Gelety <jgelety@cisco.com>

1 files changed, 95 insertions, 0 deletions

diff --git a/tests/vpp/device/container_memif/eth2p-eth-l2xcbase-eth-2memif-1dcr-dev.robot b/tests/vpp/device/container_memif/eth2p-eth-l2xcbase-eth-2memif-1dcr-dev.robot
new file mode 100644
index 0000000000..97b9b00fab
--- /dev/null
+++ b/tests/vpp/device/container_memif/eth2p-eth-l2xcbase-eth-2memif-1dcr-dev.robot
@@ -0,0 +1,95 @@
+# Copyright (c) 2019 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/l2/l2_xconnect.robot
+| Resource | resources/libraries/robot/l2/l2_traffic.robot
+| Resource | resources/libraries/robot/shared/default.robot
+| Resource | resources/libraries/robot/shared/memif.robot
+| Resource | resources/libraries/robot/shared/testing_path.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV
+| ... | FUNCTEST | L2XCFWD | BASE | ETH | MEMIF | DOCKER
+| ...
+| Test Setup | Set up VPP device test
+| ...
+| Test Teardown | Run Keywords
+| ... | Tear down functional test with container
+| ... | AND | Tear down VPP device test
+| ... | AND | Show Memif on all DUTs | ${nodes}
+| ...
+| Documentation | *L2 cross-connect test cases with memif interface*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with \
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-ICMPv4 for L2 switching of \
+| ... | IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect \
+| ... | (L2XC) switching. Container is connected to VPP via Memif interface. \
+| ... | Container is running same VPP version as running on DUT.
+| ... | *[Ver] TG verification:* Test ICMPv4 (or ICMPv6) Echo Request packets \
+| ... | are sent in both directions by TG on links to DUT1 and via container; \
+| ... | on receive TG verifies packets for correctness and their IPv4 (IPv6) \
+| ... | src-addr, dst-addr and MAC addresses.
+| ... | *[Ref] Applicable standard specifications:* RFC792
+
+*** Variables ***
+# Memif
+| ${sock_base}= | memif-DUT1_CNF1
+# Container
+| ${container_engine}= | Docker
+| ${container_chain_topology}= | chain_functional
+
+# TODO: Add update of VPP PIDs after container creation
+*** Test Cases ***
+| tc01-eth2p-ethip4-l2xcbase-eth-2memif-1dcr-device
+| | [Documentation]
+| | ... | [Top] TG=DUT=DCR. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT configure \
+| | ... | two L2 cross-connects (L2XC), each with one untagged interface \
+| | ... | to TG and untagged i/f to docker over memif. [Ver] Make \
+| | ... | TG send ICMPv4 Echo Reqs in both directions between two of its \
+| | ... | i/fs to be switched by DUT to and from docker; verify all packets \
+| | ... | are received. [Ref]
+| | ...
+| | Given Configure path in 2-node circular topology
+| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']}
+| | And Set up functional test with containers
+| | And Configure interfaces in path up
+| | When Set up memif interfaces on DUT node | ${dut_node} | ${sock_base}
+| | ... | ${sock_base} | dcr_uuid=${dcr_uuid}
+| | ... | memif_if1=memif_if1 | memif_if2=memif_if2 | rxq=${0} | txq=${0}
+| | And Configure L2XC | ${dut_node} | ${dut_to_tg_if1} | ${memif_if1}
+| | And Configure L2XC | ${dut_node} | ${dut_to_tg_if2} | ${memif_if2}
+| | Then Send ICMPv4 bidirectionally and verify received packets | ${tg_node}
+| | ... | ${tg_to_dut_if1} | ${tg_to_dut_if2}
+
+| tc02-eth2p-ethip6-l2xcbase-eth-2memif-1dcr-device
+| | [Documentation]
+| | ... | [Top] TG=DUT=DCR. [Enc] Eth-IPv6-ICMPv6. [Cfg] On DUT configure\
+| | ... | two L2 cross-connects (L2XC), each with one untagged i/f to TG\
+| | ... | and untagged i/f to docker over memif. [Ver] Make TG send\
+| | ... | ICMPv6 Echo Reqs in both directions between two of its i/fs to\
+| | ... | be switched by DUT to and from docker; verify all packets are\
+| | ... | received. [Ref]
+| | ...
+| | Given Configure path in 2-node circular topology
+| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']}
+| | And Set up functional test with containers
+| | And Configure interfaces in path up
+| | When Set up memif interfaces on DUT node | ${dut_node} | ${sock_base}
+| | ... | ${sock_base} | dcr_uuid=${dcr_uuid}
+| | ... | memif_if1=memif_if1 | memif_if2=memif_if2 | rxq=${0} | txq=${0}
+| | And Configure L2XC | ${dut_node} | ${dut_to_tg_if1} | ${memif_if1}
+| | And Configure L2XC | ${dut_node} | ${dut_to_tg_if2} | ${memif_if2}
+| | Then Send ICMPv6 bidirectionally and verify received packets | ${tg_node}
+| | ... | ${tg_to_dut_if1} | ${tg_to_dut_if2}