VPP_Device - add baseline tests - part I

CSIT-1370

Add following baseline tests to VPP_Device:
- ip4
  eth2p-ethip4-ip4base-dev
- ip6
  eth2p-ethip6-ip6base-dev
- l2bd
  eth2p-eth-l2bdbasemaclrn-dev

Change-Id: Ic20000eb38c5511c27d020f3aa76b2620d7f7ef9
Signed-off-by: Jan Gelety <jgelety@cisco.com>

1 files changed, 87 insertions, 0 deletions

diff --git a/tests/vpp/device/l2bd/eth2p-eth-l2bdbasemaclrn-dev.robot b/tests/vpp/device/l2bd/eth2p-eth-l2bdbasemaclrn-dev.robot
new file mode 100644
index 0000000000..553ed17029
--- /dev/null
+++ b/tests/vpp/device/l2bd/eth2p-eth-l2bdbasemaclrn-dev.robot
@@ -0,0 +1,87 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/l2/l2_bridge_domain.robot
+| Resource | resources/libraries/robot/l2/l2_traffic.robot
+| Resource | resources/libraries/robot/shared/default.robot
+| Resource | resources/libraries/robot/shared/interfaces.robot
+| Resource | resources/libraries/robot/shared/testing_path.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV
+| ... | FUNCTEST | L2BDMACLRN | BASE | ETH | ICMP
+| ...
+| Test Setup | Set up VPP device test
+| ...
+| Test Teardown | Tear down VPP device test
+| ...
+| Documentation | *L2 bridge-domain test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-ICMPv4 for L2 switching of\
+| ... | IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6 use. Both apply to all\
+| ... | links.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge-domain\
+| ... | switching.
+| ... | *[Ver] TG verification:* Test ICMPv4 (or ICMPv6) Echo Request packets\
+| ... | are sent in both directions by TG on links to DUT1; on receive TG\
+| ... | verifies packets for correctness and their IPv4 (IPv6) src-addr,\
+| ... | dst-addr and MAC addresses.
+| ... | *[Ref] Applicable standard specifications:* RFC792
+
+*** Variables ***
+| ${bd_id}= | 1
+
+*** Test Cases ***
+| tc01-eth2p-ethicmpv4-l2bdbase-device
+| | [Documentation]
+| | ... | [Top] TG-DUT1-TG. [Enc] Eth-IPv4-ICMPv4.
+| | ... | [Cfg] Configure L2 bridge-domain (L2BD) with MAC learning enabled on\
+| | ... | DUT1. Add both interfaces towards TG to this L2BD.
+| | ... | [Ver] Make TG send ICMPv4 Echo Req in both directions between two of\
+| | ... | its interfaces to be switched by DUT1; verify all packets are\
+| | ... | received.
+| | ...
+| | Given Configure path in 2-node circular topology
+| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']}
+| | And Set interfaces in path up
+| | And Create bridge domain | ${dut_node} | ${bd_id}
+| | And Add interface to bridge domain | ${dut_node} | ${dut_to_tg_if1}
+| | ... | ${bd_id}
+| | And Add interface to bridge domain | ${dut_node} | ${dut_to_tg_if2}
+| | ... | ${bd_id}
+| | When All Vpp Interfaces Ready Wait | ${nodes}
+| | Then Send ICMPv4 bidirectionally and verify received packets | ${tg_node}
+| | ... | ${tg_to_dut_if1} | ${tg_to_dut_if2}
+
+| tc02-eth2p-ethicmpv6-l2bdbase-device
+| | [Documentation]
+| | ... | [Top] TG-DUT1-TG. [Enc] Eth-IPv6-ICMPv6.
+| | ... | [Cfg] Configure L2 bridge-domain (L2BD) with MAC learning enabled on\
+| | ... | DUT1. Add both interfaces towards TG to this L2BD.
+| | ... | [Ver] Make TG send ICMPv6 Echo Req in both directions between two of\
+| | ... | its interfaces to be switched by DUT1; verify all packets are\
+| | ... | received.
+| | ...
+| | Given Configure path in 2-node circular topology
+| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']}
+| | And Set interfaces in path up
+| | And Create bridge domain | ${dut_node} | ${bd_id}
+| | And Add interface to bridge domain | ${dut_node} | ${dut_to_tg_if1}
+| | ... | ${bd_id}
+| | And Add interface to bridge domain | ${dut_node} | ${dut_to_tg_if2}
+| | ... | ${bd_id}
+| | When All Vpp Interfaces Ready Wait | ${nodes}
+| | Then Send ICMPv6 bidirectionally and verify received packets
+| | ... | ${tg_node} | ${tg_to_dut_if1} | ${tg_to_dut_if2}