Add ipsec crypto test for Denverton platform

add ipsec cryto test to support Denverton hardware crypto device C3xxx.
replace HW_cryptodev keyword to HW_DH895xcc or HW_C3xxx, or add more other
hardware crypto device type support in the future.

Change-Id: I181bca4095757fde7ca45ab3856273ac5930d902
Signed-off-by: Yulong Pei <yulong.pei@intel.com>

1 files changed, 157 insertions, 0 deletions

diff --git a/tests/vpp/perf/crypto/10ge2p1x553-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr.robot b/tests/vpp/perf/crypto/10ge2p1x553-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr.robot
new file mode 100644
index 0000000000..c0a9059a1d
--- /dev/null
+++ b/tests/vpp/perf/crypto/10ge2p1x553-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr.robot
@@ -0,0 +1,157 @@
+# Copyright (c) 2019 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/crypto/ipsec.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | IP4FWD | IPSEC | IPSECSW | IPSECTUN | NIC_Intel-X553 | BASE
+| ...
+| Suite Setup | Set up IPSec performance test suite | L3 | Intel-X553
+| ... | SW_cryptodev
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 IPsec tunnel mode performance test suite.*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 on TG-DUTn,
+| ... | Eth-IPv4-IPSec on DUT1-DUT2
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with DPDK SW
+| ... | crypto devices and multiple IPsec tunnels between them.
+| ... | DUTs get IPv4 traffic from TG, encrypt it
+| ... | and send to another DUT, where packets are decrypted and sent back to TG
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
+| ... | at line rate and reports total received/sent packets over trial period.
+| ... | Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, number of flows per flow-group equals to
+| ... | number of IPSec tunnels) with all packets
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and
+| ... | static payload. MAC addresses are matching MAC addresses of the TG
+| ... | node interfaces. Incrementing of IP.dst (IPv4 destination address) field
+| ... | is applied to both streams.
+| ... | *[Ref] Applicable standard specifications:* RFC4303 and RFC2544.
+
+*** Variables ***
+# X553 bandwidth limit 20Gbps/2=10Gbps
+| ${s_10G}= | ${10000000000}
+# X553 Mpps limit 29.76Mpps/2=14.88Mpps
+| ${s_14.88Mpps}= | ${14880952}
+| ${tg_if1_ip4}= | 192.168.10.2
+| ${dut1_if1_ip4}= | 192.168.10.1
+| ${dut1_if2_ip4}= | 172.168.1.1
+| ${dut2_if1_ip4}= | 172.168.1.2
+| ${dut2_if2_ip4}= | 192.168.20.1
+| ${tg_if2_ip4}= | 192.168.20.2
+| ${raddr_ip4}= | 20.0.0.0
+| ${laddr_ip4}= | 10.0.0.0
+| ${addr_range}= | ${32}
+| ${overhead}= | ${54}
+| ${n_tunnels}= | ${1}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4dst${n_tunnels}
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPSec tunneling CBC-SHA1 config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | ${encr_alg} = | Crypto Alg AES CBC 128
+| | ${auth_alg} = | Integ Alg SHA1 96
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_10G} | ${framesize} | overhead=${overhead}
+| | ... | pps_limit=${s_14.88Mpps}
+| | And Add DPDK SW cryptodev on DUTs in 3-node single-link circular topology
+| | ... | aesni_mb | ${phy_cores}
+| | And Add DPDK dev default RXD to all DUTs | 2048
+| | And Add DPDK dev default TXD to all DUTs | 2048
+| | And Apply startup configuration on all VPP DUTs
+| | When Generate keys for IPSec | ${encr_alg} | ${auth_alg}
+| | And Initialize IPSec in 3-node circular topology
+| | And VPP IPsec Create Tunnel Interfaces
+| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2}
+| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg}
+| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}