CSIT-687: Directory structure reorganization

Change-Id: I772c9e214be2461adf58124998d272e7d795220f
Signed-off-by: Tibor Frank <tifrank@cisco.com>
Signed-off-by: Maciek Konstantynowicz <mkonstan@cisco.com>

1 files changed, 332 insertions, 0 deletions

diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4base-iacldstbase-ndrchk.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4base-iacldstbase-ndrchk.robot
new file mode 100644
index 0000000000..3a070f8eaf
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4base-iacldstbase-ndrchk.robot
@@ -0,0 +1,332 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.Classify.Classify
+| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']}
+| ... | WITH NAME | dut1_v4
+| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']}
+| ... | WITH NAME | dut2_v4
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK
+| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | FEATURE | IACLDST
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| Test Teardown | Tear down performance ndrchk test
+| ...
+| Documentation | *Reference NDR throughput IPv4 whitelist verify test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist
+| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG.
+| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In short performance tests, TG verifies
+| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet
+| ... | loss tolerance. Ref-NDR value is periodically updated acording to
+| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long
+| ... | performance tests for the same DUT configuration. Test packets are
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3
+| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61
+| ... | and static payload. MAC addresses are matching MAC addresses of the
+| ... | TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip4-ip4src253
+
+*** Test Cases ***
+| tc01-64B-1t1c-ethip4-ip4base-iacldstbase-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 64 Byte frames using single trial throughput test
+| | ... | at 2x 3.6mpps.
+| | [Tags] | 64B | 1T1C | STHREAD
+| | ${framesize}= | Set Variable | ${64}
+| | ${rate}= | Set Variable | 3.6mpps
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc02-1518B-1t1c-ethip4-ip4base-iacldstbase-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 1518 Byte frames using single trial throughput test
+| | ... | at 2x 812743pps.
+| | [Tags] | 1518B | 1T1C | STHREAD
+| | ${framesize}= | Set Variable | ${1518}
+| | ${rate}= | Set Variable | 812743pps
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc03-9000B-1t1c-ethip4-ip4base-iacldstbase-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 9000 Byte frames using single trial throughput test
+| | ... | at 2x 138580pps.
+| | [Tags] | 9000B | 1T1C | STHREAD
+| | ${framesize}= | Set Variable | ${9000}
+| | ${rate}= | Set Variable | 138580pps
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc04-64B-2t2c-ethip4-ip4base-iacldstbase-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 64 Byte frames using single trial throughput test
+| | ... | at 2x 6.3mpps.
+| | [Tags] | 64B | 2T2C | MTHREAD
+| | ${framesize}= | Set Variable | ${64}
+| | ${rate}= | Set Variable | 6.3mpps
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc05-1518B-2t2c-ethip4-ip4base-iacldstbase-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 1518 Byte frames using single trial throughput test
+| | ... | at 2x 812743pps.
+| | [Tags] | 1518B | 2T2C | MTHREAD
+| | ${framesize}= | Set Variable | ${1518}
+| | ${rate}= | Set Variable | 812743pps
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc06-9000B-2t2c-ethip4-ip4base-iacldstbase-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 9000 Byte frames using single trial throughput test
+| | ... | at 2x 138580pps.
+| | [Tags] | 9000B | 2T2C | MTHREAD
+| | ${framesize}= | Set Variable | ${9000}
+| | ${rate}= | Set Variable | 138580pps
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc07-64B-4t4c-ethip4-ip4base-iacldstbase-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 64 Byte frames using single trial throughput test
+| | ... | at 2x 9.7mpps.
+| | [Tags] | 64B | 4T4C | MTHREAD
+| | ${framesize}= | Set Variable | ${64}
+| | ${rate}= | Set Variable | 9.7mpps
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv4 forwarding in 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc08-1518B-4t4c-ethip4-ip4base-iacldstbase-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 1518 Byte frames using single trial throughput test
+| | ... | at 2x 812743pps.
+| | [Tags] | 1518B | 4T4C | MTHREAD
+| | ${framesize}= | Set Variable | ${1518}
+| | ${rate}= | Set Variable | 812743pps
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}
+
+| tc09-9000B-4t4c-ethip4-ip4base-iacldstbase-ndrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 9000 Byte frames using single trial throughput test
+| | ... | at 2x 138580pps.
+| | [Tags] | 9000B | 4T4C | MTHREAD
+| | ${framesize}= | Set Variable | ${9000}
+| | ${rate}= | Set Variable | 138580pps
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
+| | ... | ${framesize} | ${traffic_profile}