Add ARM Taishan testbed33 perftest

Change-Id: Iaa0e7fbca7de26c7dce8b389cc3494f628a2ecd0
Signed-off-by: Stanislav Chlebec <stanislav.chlebec@pantheon.tech>
Signed-off-by: juraj.linkes <juraj.linkes@pantheon.tech>

22 files changed, 3006 insertions, 0 deletions

diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-dot1q-ip4base-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-dot1q-ip4base-mrr.robot
new file mode 100644
index 0000000000..dc09f00233
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-dot1q-ip4base-mrr.robot
@@ -0,0 +1,134 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | BASE | DOT1Q | IP4BASE
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| ...
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. IEEE 802.1Q\
+| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and two static IPv4 /30 route entries. DUT1 and DUT2 tested\
+| ... | with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# TG subnets used by T-Rex
+| ${tg_if1_net}= | 10.10.10.0
+| ${tg_if2_net}= | 20.20.20.0
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs IPv4 routing with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize} | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with VLAN dot1q sub-interfaces in circular topology
+| | ... | ${tg_if1_net} | ${tg_if2_net} | ${subid} | ${tag_rewrite}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-ip4base-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-ip4base-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-ip4base-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-ip4base-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-ip4base-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-ip4base-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-ip4base-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-ip4base-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-ip4base-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-ip4base-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-ip4base-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-ip4base-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-dot1q-ip4base-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-dot1q-ip4base-ndrpdr.robot
new file mode 100644
index 0000000000..2b65609d7b
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-dot1q-ip4base-ndrpdr.robot
@@ -0,0 +1,141 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | BASE | DOT1Q | IP4BASE
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| ...
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing with IEEE 802.1Q test\
+| ... | cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. IEEE 802.1Q\
+| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and two static IPv4 /30 route entries. DUT1 and DUT2 tested\
+| ... | with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP\
+| ... | protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# TG subnets used by T-Rex
+| ${tg_if1_net}= | 10.10.10.0
+| ${tg_if2_net}= | 20.20.20.0
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs IPv4 routing with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize} | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with VLAN dot1q sub-interfaces in circular topology
+| | ... | ${tg_if1_net} | ${tg_if2_net} | ${subid} | ${tag_rewrite}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-ip4base-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-ip4base-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-ip4base-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-ip4base-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-ip4base-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-ip4base-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-ip4base-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-ip4base-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-ip4base-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-ip4base-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-ip4base-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-ip4base-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-copwhtlistbase-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-copwhtlistbase-mrr.robot
new file mode 100644
index 0000000000..7deca2a14b
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-copwhtlistbase-mrr.robot
@@ -0,0 +1,136 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.Cop
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | COPWHLIST
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 whitelist test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing, two static IPv4 /24 routes and IPv4 COP security whitelist
+| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG.
+| ... | DUT1 and DUT2 tested with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
+| ... | at line rate and reports total received/sent packets over trial period.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | And Add Fib Table | ${dut1} | 1
+| | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | vrf=1 | local=${TRUE}
+| | And Add Fib Table | ${dut2} | 1
+| | And Vpp Route Add | ${dut2} | 20.20.20.0 | 24 | vrf=1 | local=${TRUE}
+| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip4 | 1
+| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip4 | 1
+| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-copwhtlistbase-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-copwhtlistbase-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-copwhtlistbase-ndrpdr.robot
new file mode 100644
index 0000000000..73ccee2c76
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-copwhtlistbase-ndrpdr.robot
@@ -0,0 +1,142 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.Cop
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | COPWHLIST
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 whitelist test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing, two static IPv4 /24 routes and IPv4 COP security whitelist
+| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG.
+| ... | DUT1 and DUT2 tested with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using MLRsearch library.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | And Add Fib Table | ${dut1} | 1
+| | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | vrf=1 | local=${TRUE}
+| | And Add Fib Table | ${dut2} | 1
+| | And Vpp Route Add | ${dut2} | 20.20.20.0 | 24 | vrf=1 | local=${TRUE}
+| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip4 | 1
+| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip4 | 1
+| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-ipolicemarkbase-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-ipolicemarkbase-mrr.robot
new file mode 100644
index 0000000000..7df1bcd994
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-ipolicemarkbase-mrr.robot
@@ -0,0 +1,134 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.Policer
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | IP4FWD | FEATURE | POLICE_MARK
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 policer test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and two static IPv4 /24 route entries and policer with 2R3C
+| ... | color-aware configuration. Policer is applied on links TG - DUT1 and
+| ... | DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv6 header
+| ... | and generated payload. MAC addresses are matching MAC addresses
+| ... | of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC2698.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${cir}= | ${100}
+| ${eir}= | ${150}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${cb} | ${framesize}
+| | Set Test Variable | ${eb} | ${framesize}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-ipolicemarkbase-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-ipolicemarkbase-ndrpdr.robot
new file mode 100644
index 0000000000..49f1ea5d14
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-ipolicemarkbase-ndrpdr.robot
@@ -0,0 +1,139 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.Policer
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | IP4FWD | FEATURE | POLICE_MARK
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 policer test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and two static IPv4 /24 route entries and policer with 2R3C
+| ... | color-aware configuration. Policer is applied on links TG - DUT1 and
+| ... | DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using MLRsearch library.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv6 header
+| ... | and generated payload. MAC addresses are matching MAC addresses
+| ... | of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC2698.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${cir}= | ${100}
+| ${eir}= | ${150}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | Set Test Variable | ${cb} | ${framesize}
+| | Set Test Variable | ${eb} | ${framesize}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-mrr.robot
new file mode 100644
index 0000000000..a318298a7a
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-mrr.robot
@@ -0,0 +1,125 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | BASE | IP4BASE
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with
+| ... | 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
+| ... | at line rate and reports total received/sent packets over trial period.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-ndrpdr.robot
new file mode 100644
index 0000000000..0faaa2f378
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4base-ndrpdr.robot
@@ -0,0 +1,131 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | BASE | IP4BASE
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with
+| ... | 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using MLRsearch library.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale200k-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale200k-mrr.robot
new file mode 100644
index 0000000000..9a44555ecc
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale200k-mrr.robot
@@ -0,0 +1,128 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | SCALE | FIB_200K
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested\
+| ... | with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${100000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale200k-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale200k-ndrpdr.robot
new file mode 100644
index 0000000000..86ef486c5b
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale200k-ndrpdr.robot
@@ -0,0 +1,134 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | SCALE | FIB_200K
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested\
+| ... | with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${100000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale20k-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale20k-mrr.robot
new file mode 100644
index 0000000000..797e2a4b21
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale20k-mrr.robot
@@ -0,0 +1,128 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | SCALE | FIB_20K
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested\
+| ... | with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${10000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale20k-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale20k-ndrpdr.robot
new file mode 100644
index 0000000000..97dbaa1b75
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale20k-ndrpdr.robot
@@ -0,0 +1,134 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | SCALE | FIB_20K
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested\
+| ... | with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${10000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale2m-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale2m-mrr.robot
new file mode 100644
index 0000000000..9e55382739
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale2m-mrr.robot
@@ -0,0 +1,128 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | SCALE | FIB_2M
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested\
+| ... | with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${1000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale2m-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale2m-ndrpdr.robot
new file mode 100644
index 0000000000..9c11f1f3f0
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4-ip4scale2m-ndrpdr.robot
@@ -0,0 +1,134 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | SCALE | FIB_2M
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-82599ES
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested\
+| ... | with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${1000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sf-10kflows-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sf-10kflows-mrr.robot
new file mode 100644
index 0000000000..749f11a813
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sf-10kflows-mrr.robot
@@ -0,0 +1,147 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 3-node performance topology with DUT's NIC model | L3
+| ... | Intel-82599ES
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC 82599ES Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-3n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr.robot
new file mode 100644
index 0000000000..3d17e93d4b
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr.robot
@@ -0,0 +1,153 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 3-node performance topology with DUT's NIC model | L3
+| ... | Intel-82599ES
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC 82599ES Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-3n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sl-10kflows-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sl-10kflows-mrr.robot
new file mode 100644
index 0000000000..d6f420db07
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sl-10kflows-mrr.robot
@@ -0,0 +1,147 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 3-node performance topology with DUT's NIC model | L3
+| ... | Intel-82599ES
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC 82599ES Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-3n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr.robot
new file mode 100644
index 0000000000..f122dfa5c8
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr.robot
@@ -0,0 +1,153 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 3-node performance topology with DUT's NIC model | L3
+| ... | Intel-82599ES
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC 82599ES Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-3n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-nat44-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-nat44-mrr.robot
new file mode 100644
index 0000000000..b62048f4f3
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-nat44-mrr.robot
@@ -0,0 +1,131 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/ip/nat.robot
+| Resource | resources/libraries/robot/shared/traffic.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | NAT44 | BASE
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 3-node performance topology with DUT's NIC model | L3
+| ... | Intel-82599ES
+| ... | AND | Set up performance test suite with NAT
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results NAT44 performance test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2
+| ... | tested with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
+| ... | at line rate and reports total received/sent packets over trial period.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4udp-1u1p
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Add NAT to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize NAT44 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-nat44-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-nat44-ndrpdr.robot
new file mode 100644
index 0000000000..f5b4c25293
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4base-nat44-ndrpdr.robot
@@ -0,0 +1,137 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/ip/nat.robot
+| Resource | resources/libraries/robot/shared/traffic.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | NAT44 | BASE
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 3-node performance topology with DUT's NIC model | L3
+| ... | Intel-82599ES
+| ... | AND | Set up performance test suite with NAT
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput NAT44 performance test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2
+| ... | tested with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using MLRsearch library.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4udp-1u1p
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Add NAT to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize NAT44 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr.robot
new file mode 100644
index 0000000000..deb12e279e
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr.robot
@@ -0,0 +1,132 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/ip/nat.robot
+| Resource | resources/libraries/robot/shared/traffic.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | NAT44 | SRC_USER_1000
+| ... | SCALE
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 3-node performance topology with DUT's NIC model | L3
+| ... | Intel-82599ES
+| ... | AND | Set up performance test suite with NAT
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results NAT44 performance test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2
+| ... | tested with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
+| ... | at line rate and reports total received/sent packets over trial period.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4udp-1000u15p
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Add NAT to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize NAT44 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr.robot
new file mode 100644
index 0000000000..9323778a50
--- /dev/null
+++ b/tests/vpp/perf/ip4/10ge2p1x82599es-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr.robot
@@ -0,0 +1,138 @@
+# Copyright (c) 2019 PANTHEON.tech and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/ip/nat.robot
+| Resource | resources/libraries/robot/shared/traffic.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-82599ES | ETH | IP4FWD | FEATURE | NAT44 | SRC_USER_1000
+| ... | SCALE
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 3-node performance topology with DUT's NIC model | L3
+| ... | Intel-82599ES
+| ... | AND | Set up performance test suite with NAT
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput  NAT44 performance test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2
+| ... | tested with 2p10GE NIC 82599ES by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using MLRsearch library.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# 82599ES bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4udp-1000u15p
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Add NAT to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize NAT44 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}