CSIT-1097: Ip6 NDRPDR and edited MRR suites

Change-Id: I912017c6d1eab5530eecb2326887ffd057916ee8
Signed-off-by: Vratko Polak <vrpolak@cisco.com>

1 files changed, 0 insertions, 457 deletions

diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale200k-ndrpdrdisc.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale200k-ndrpdrdisc.robot
deleted file mode 100644
index 26b94f8919..0000000000
--- a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale200k-ndrpdrdisc.robot
+++ /dev/null
@@ -1,457 +0,0 @@
-# Copyright (c) 2017 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance/performance_setup.robot
-| ...
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
-| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_200K
-| ...
-| Suite Setup | Set up 3-node performance topology with DUT's NIC model
-| ... | L3 | Intel-X520-DA2
-| Suite Teardown | Tear down 3-node performance topology
-| ...
-| Test Setup | Set up performance test
-| ...
-| Test Teardown | Tear down performance discovery test | ${min_rate}pps
-| ... | ${framesize} | ${traffic_profile}
-| ...
-| Documentation | *RFC2544: Pkt throughput IPv6 routing test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6
-| ... | routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested
-| ... | with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using either binary search or linear search
-| ... | algorithms with configured starting rate and final step that determines
-| ... | throughput measurement resolution. Test packets are generated by TG on
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
-| ... | (flow-group per direction, 100k flows per flow-group) with all packets
-| ... | containing Ethernet header, IPv6 header withq IP and static payload.
-| ... | MAC addresses are matching MAC addresses of the TG node interfaces.
-| ... | Incrementing of IP.dst (IPv6 destination address) field is applied to
-| ... | both streams.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Variables ***
-# X520-DA2 bandwidth limit
-| ${s_limit} | ${10000000000}
-| ${rts_per_flow}= | ${100000}
-# Traffic profile:
-| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow}
-
-*** Test Cases ***
-| tc01-78B-1t1c-ethip6-ip6scale200k-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps.
-| | [Tags] | 78B | 1C | NDRDISC
-| | ${framesize}= | Set Variable | ${78}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 1
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc02-78B-1t1c-ethip6-ip6scale200k-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps, LT=0.5%.
-| | [Tags] | 78B | 1C | PDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${78}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 1
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
-
-| tc03-1518B-1t1c-ethip6-ip6scale200k-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps.
-| | [Tags] | 1518B | 1C | NDRDISC
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 1
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc04-1518B-1t1c-ethip6-ip6scale200k-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps, LT=0.5%.
-| | [Tags] | 1518B | 1C | PDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 1
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
-
-| tc05-9000B-1t1c-ethip6-ip6scale200k-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames
-| | ... | using binary search start at 10GE linerate, step 10kpps.
-| | [Tags] | 9000B | 1C | NDRDISC
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 1
-| | And Add PCI devices to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc06-9000B-1t1c-ethip6-ip6scale200k-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 1 phy core, \
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames
-| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
-| | [Tags] | 9000B | 1C | PDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 1
-| | And Add PCI devices to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
-
-| tc07-78B-2t2c-ethip6-ip6scale200k-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps.
-| | [Tags] | 78B | 2C | NDRDISC
-| | ${framesize}= | Set Variable | ${78}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 2
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc08-78B-2t2c-ethip6-ip6scale200k-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps, LT=0.5%.
-| | [Tags] | 78B | 2C | PDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${78}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 2
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
-
-| tc09-1518B-2t2c-ethip6-ip6scale200k-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps.
-| | [Tags] | 1518B | 2C | NDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 2
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc10-1518B-2t2c-ethip6-ip6scale200k-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps, LT=0.5%.
-| | [Tags] | 1518B | 2C | PDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 2
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
-
-| tc11-9000B-2t2c-ethip6-ip6scale200k-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames
-| | ... | using binary search start at 10GE linerate, step 10kpps.
-| | [Tags] | 9000B | 2C | NDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 2
-| | And Add PCI devices to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc12-9000B-2t2c-ethip6-ip6scale200k-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 2 phy cores, \
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames
-| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
-| | [Tags] | 9000B | 2C | PDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 2
-| | And Add PCI devices to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
-
-| tc13-78B-4t4c-ethip6-ip6scale200k-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 phy cores, \
-| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps.
-| | [Tags] | 78B | 4C | NDRDISC
-| | ${framesize}= | Set Variable | ${78}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 4
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc14-78B-4t4c-ethip6-ip6scale200k-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 phy cores, \
-| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps, LT=0.5%.
-| | [Tags] | 78B | 4C | PDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${78}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 4
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
-
-| tc15-1518B-4t4c-ethip6-ip6scale200k-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 phy cores, \
-| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps.
-| | [Tags] | 1518B | 4C | NDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 4
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc16-1518B-4t4c-ethip6-ip6scale200k-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 phy cores, \
-| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames
-| | ... | using binary search start at 10GE linerate, step 50kpps, LT=0.5%.
-| | [Tags] | 1518B | 4C | PDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${50000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 4
-| | And Add PCI devices to all DUTs
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
-
-| tc17-9000B-4t4c-ethip6-ip6scale200k-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 phy cores, \
-| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames
-| | ... | using binary search start at 10GE linerate, step 10kpps.
-| | [Tags] | 9000B | 4C | NDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 4
-| | And Add PCI devices to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc18-9000B-4t4c-ethip6-ip6scale200k-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv6 routing config with 4 phy cores, \
-| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames
-| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
-| | [Tags] | 9000B | 4C | PDRDISC | SKIP_PATCH
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add worker threads and rxqueues to all DUTs | 4
-| | And Add PCI devices to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize IPv6 forwarding with scaling in 3-node circular topology
-| | ... | ${rts_per_flow}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}