CSIT-1032: MRR Tests: IPv6, x710

 ─ 10ge2p1x710-ethip6-ip6base-copwhtlistbase-mrr.robot
 ─ 10ge2p1x710-ethip6-ip6base-iacldstbase-mrr.robot
 ─ 10ge2p1x710-ethip6-ip6base-mrr.robot
 ─ 10ge2p1x710-ethip6-ip6scale200k-mrr.robot
 ─ 10ge2p1x710-ethip6-ip6scale20k-mrr.robot
 ─ 10ge2p1x710-ethip6-ip6scale2m-mrr.robot

Change-Id: I270c1e52e61fd9765f139983d133432a3058c722
Signed-off-by: Tibor Frank <tifrank@cisco.com>

1 files changed, 225 insertions, 0 deletions

diff --git a/tests/vpp/perf/ip6/10ge2p1x710-ethip6-ip6scale20k-mrr.robot b/tests/vpp/perf/ip6/10ge2p1x710-ethip6-ip6scale20k-mrr.robot
new file mode 100644
index 0000000000..f49f0f7fd3
--- /dev/null
+++ b/tests/vpp/perf/ip6/10ge2p1x710-ethip6-ip6scale20k-mrr.robot
@@ -0,0 +1,225 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | ETH | IP6FWD | SCALE | FIB_20K
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X710
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Documentation | *Raw results IPv6 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6
+| ... | routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested
+| ... | with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, 10k flows per flow-group) with all packets
+| ... | containing Ethernet header, IPv6 header withq IP and static payload.
+| ... | MAC addresses are matching MAC addresses of the TG node interfaces.
+| ... | Incrementing of IP.dst (IPv6 destination address) field is applied to
+| ... | both streams.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${10000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip6-ip6dst${rts_per_flow}
+
+*** Keywords ***
+| Check RR for ip6base-ip6scale
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with ${wt} \
+| | ... | thread(s), ${wt} phy core(s), ${rxq} receive queue(s) per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Arguments] | ${framesize} | ${wt} | ${rxq}
+| | ...
+| | # Test Variables required for test teardown
+| | Set Test Variable | ${framesize}
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Run Keyword If | ${get_framesize} < ${1522}
+| | ... | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv6 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate | ${perf_trial_duration}
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-78B-1t1c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 78B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 78B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=1 | rxq=1 | framesize=${78}
+
+| tc02-1518B-1t1c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 1518B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=1 | rxq=1 | framesize=${1518}
+
+| tc03-9000B-1t1c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 9000B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=1 | rxq=1 | framesize=${9000}
+
+| tc04-IMIX-1t1c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\
+| | ... | throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | IMIX | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=1 | rxq=1 | framesize=IMIX_v4_1
+
+| tc05-78B-2t2c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 78B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 78B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=2 | rxq=1 | framesize=${78}
+
+| tc06-1518B-2t2c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 1518B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=2 | rxq=1 | framesize=${1518}
+
+| tc07-9000B-2t2c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 9000B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=2 | rxq=1 | framesize=${9000}
+
+| tc08-IMIX-2t2c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\
+| | ... | throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | IMIX | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=2 | rxq=1 | framesize=IMIX_v4_1
+
+| tc09-78B-4t4c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 78B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 78B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=4 | rxq=2 | framesize=${78}
+
+| tc10-1518B-4t4c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 1518B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=4 | rxq=2 | framesize=${1518}
+
+| tc11-9000B-4t4c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 9000B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=4 | rxq=2 | framesize=${9000}
+
+| tc12-IMIX-4t4c-ethip6-ip6base-ip6scale20k-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\
+| | ... | throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | IMIX | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for ip6base-ip6scale
+| | wt=4 | rxq=2 | framesize=IMIX_v4_1