Remove obsolete NDRPDR checks

Change-Id: If495493f4dce8d2eecfb8c06bcd587f315b70b1d
Signed-off-by: Peter Mikus <pmikus@cisco.com>

1 files changed, 0 insertions, 266 deletions

diff --git a/tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip6-ip6base-ndrchk.robot b/tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip6-ip6base-ndrchk.robot
deleted file mode 100644
index 2e44791318..0000000000
--- a/tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip6-ip6base-ndrchk.robot
+++ /dev/null
@@ -1,266 +0,0 @@
-# Copyright (c) 2017 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance/performance_setup.robot
-| Resource | resources/libraries/robot/overlay/lisp_static_adjacency.robot
-| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
-| ...
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK
-| ... | NIC_Intel-X520-DA2 | IP6FWD | ENCAP | LISP | IP6UNRLAY | IP6OVRLAY
-| ...
-| Suite Setup | Set up 3-node performance topology with DUT's NIC model
-| ... | L3 | Intel-X520-DA2
-| Suite Teardown | Tear down 3-node performance topology
-| ...
-| Test Setup | Set up performance test
-| Test Teardown | Tear down performance ndrchk test
-| ...
-| Documentation | *Reference NDR throughput Lisp tunnel verify test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv6-LISP-IPv6 on DUT1-DUT2,\
-| ... | Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\
-| ... | routing and static routes. LISPoIPv6 tunnel is configured\
-| ... | between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520\
-| ... | Niantic by Intel.
-| ... | *[Ver] TG verification:* In short performance tests, TG verifies\
-| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet\
-| ... | loss tolerance. Ref-NDR value is periodically updated acording to\
-| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long\
-| ... | performance tests for the same DUT confiiguration. Test packets are\
-| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\
-| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with\
-| ... | all packets containing Ethernet header, IPv6 header with\
-| ... | IP protocol=61 and generated payload.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Variables ***
-# Traffic profile:
-| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253
-
-*** Test Cases ***
-| tc01-78B-1t1c-ethip6lispip6-ip6base-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\
-| | ... | throughput test at 2x 1.56mpps.
-| | [Tags] | 78B | 1T1C | STHREAD
-| | ${framesize}= | Set Variable | ${78}
-| | ${rate}= | Set Variable | 1.56mpps
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize LISP IPv6 forwarding in 3-node circular topology
-| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
-| | ... | ${dut2_to_tg_ip6} | ${prefix6}
-| | And Configure LISP topology in 3-node circular topology
-| | ... | ${dut1} | ${dut1_if2} | ${NONE}
-| | ... | ${dut2} | ${dut2_if1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
-| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc02-1460B-1t1c-ethip6lispip6-ip6base-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial\
-| | ... | throughput test at 2x 740000pps.
-| | [Tags] | 1460B | 1T1C | STHREAD
-| | ${framesize}= | Set Variable | ${1460}
-| | ${rate}= | Set Variable | 740000pps
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize LISP IPv6 forwarding in 3-node circular topology
-| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
-| | ... | ${dut2_to_tg_ip6} | ${prefix6}
-| | And Configure LISP topology in 3-node circular topology
-| | ... | ${dut1} | ${dut1_if2} | ${NONE}
-| | ... | ${dut2} | ${dut2_if1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
-| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc03-9000B-1t1c-ethip6lispip6-ip6base-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\
-| | ... | throughput test at 2x 120000pps.
-| | [Tags] | 9000B | 1T1C | STHREAD
-| | ${framesize}= | Set Variable | ${9000}
-| | ${rate}= | Set Variable | 120000pps
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize LISP IPv6 forwarding in 3-node circular topology
-| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
-| | ... | ${dut2_to_tg_ip6} | ${prefix6}
-| | And Configure LISP topology in 3-node circular topology
-| | ... | ${dut1} | ${dut1_if2} | ${NONE}
-| | ... | ${dut2} | ${dut2_if1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
-| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc04-78B-2t2c-ethip6lispip6-ip6base-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs LISP tunnel config with 2 thread, 2 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\
-| | ... | throughput test at 2x 3.2mpps.
-| | [Tags] | 78B | 2T2C | MTHREAD
-| | ${framesize}= | Set Variable | ${78}
-| | ${rate}= | Set Variable | 3.2mpps
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize LISP IPv6 forwarding in 3-node circular topology
-| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
-| | ... | ${dut2_to_tg_ip6} | ${prefix6}
-| | And Configure LISP topology in 3-node circular topology
-| | ... | ${dut1} | ${dut1_if2} | ${NONE}
-| | ... | ${dut2} | ${dut2_if1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
-| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc05-1460B-2t2c-ethip6lispip6-ip6base-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial\
-| | ... | throughput test at 2x 740000pps.
-| | [Tags] | 1460B | 2T2C | MTHREAD
-| | ${framesize}= | Set Variable | ${1460}
-| | ${rate}= | Set Variable | 740000pps
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize LISP IPv6 forwarding in 3-node circular topology
-| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
-| | ... | ${dut2_to_tg_ip6} | ${prefix6}
-| | And Configure LISP topology in 3-node circular topology
-| | ... | ${dut1} | ${dut1_if2} | ${NONE}
-| | ... | ${dut2} | ${dut2_if1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
-| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc06-9000B-2t2c-ethip6lispip6-ip6base-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\
-| | ... | throughput test at 2x 120000pps.
-| | [Tags] | 9000B | 2T2C | MTHREAD
-| | ${framesize}= | Set Variable | ${9000}
-| | ${rate}= | Set Variable | 120000pps
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize LISP IPv6 forwarding in 3-node circular topology
-| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
-| | ... | ${dut2_to_tg_ip6} | ${prefix6}
-| | And Configure LISP topology in 3-node circular topology
-| | ... | ${dut1} | ${dut1_if2} | ${NONE}
-| | ... | ${dut2} | ${dut2_if1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
-| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc07-78B-4t4c-ethip6lispip6-ip6base-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\
-| | ... | throughput test at 2x 3.2mpps.
-| | [Tags] | 78B | 4T4C | MTHREAD
-| | ${framesize}= | Set Variable | ${78}
-| | ${rate}= | Set Variable | 3.2mpps
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize LISP IPv6 forwarding in 3-node circular topology
-| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
-| | ... | ${dut2_to_tg_ip6} | ${prefix6}
-| | And Configure LISP topology in 3-node circular topology
-| | ... | ${dut1} | ${dut1_if2} | ${NONE}
-| | ... | ${dut2} | ${dut2_if1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
-| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc08-1460B-4t4c-ethip6lispip6-ip6base-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial\
-| | ... | throughput test at 2x 740000pps.
-| | [Tags] | 1460B | 4T4C | MTHREAD
-| | ${framesize}= | Set Variable | ${1460}
-| | ${rate}= | Set Variable | 740000pps
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize LISP IPv6 forwarding in 3-node circular topology
-| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
-| | ... | ${dut2_to_tg_ip6} | ${prefix6}
-| | And Configure LISP topology in 3-node circular topology
-| | ... | ${dut1} | ${dut1_if2} | ${NONE}
-| | ... | ${dut2} | ${dut2_if1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
-| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}
-
-| tc09-9000B-4t4c-ethip6lispip6-ip6base-ndrchk
-| | [Documentation]
-| | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\
-| | ... | throughput test at 2x 120000pps.
-| | [Tags] | 9000B | 4T4C | MTHREAD
-| | ${framesize}= | Set Variable | ${9000}
-| | ${rate}= | Set Variable | 120000pps
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize LISP IPv6 forwarding in 3-node circular topology
-| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
-| | ... | ${dut2_to_tg_ip6} | ${prefix6}
-| | And Configure LISP topology in 3-node circular topology
-| | ... | ${dut1} | ${dut1_if2} | ${NONE}
-| | ... | ${dut2} | ${dut2_if1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
-| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
-| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate}
-| | ... | ${framesize} | ${traffic_profile}