CSIT-1033: MRR Tests: L2, x710

 ─ 10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot
 ─ 10ge2p1x710-dot1q-l2xcbase-mrr.robot
 ─ 10ge2p1x710-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr.robot
 ─ 10ge2p1x710-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr.robot
 ─ 10ge2p1x710-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr.robot
 ─ 10ge2p1x710-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr.robot
 ─ 10ge2p1x710-eth-l2bdscale100kmaclrn-mrr.robot
 ─ 10ge2p1x710-eth-l2bdscale10kmaclrn-mrr.robot
 ─ 10ge2p1x710-eth-l2bdscale1mmaclrn-mrr.robot
 ─ 10ge2p1x710-eth-l2xcbase-mrr.robot

Change-Id: Ic5d5cb377eca25daaeb22e8390632a6d6421c2e3
Signed-off-by: Tibor Frank <tifrank@cisco.com>

1 files changed, 233 insertions, 0 deletions

diff --git a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-mrr.robot b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-mrr.robot
new file mode 100644
index 0000000000..b3a35639c9
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-mrr.robot
@@ -0,0 +1,233 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/l2/tagging.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | L2XCFWD | BASE | DOT1Q
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X710
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Documentation | *Raw results L2XC with 802.1q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q\
+| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross-\
+| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets\
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
+| ... | payload. MAC addresses are matching MAC addresses of the TG node\
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+# X710-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254
+
+*** Keywords ***
+| Check RR for L2XC dot1q-l2xcbase
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC config with VLAN dot1q with ${wt} thread(s), \
+| | ... | ${wt} phy core(s), ${rxq} receive queue(s) per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Arguments] | ${framesize} | ${wt} | ${rxq}
+| | ...
+| | # Test Variables required for test teardown
+| | Set Test Variable | ${framesize}
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Run Keyword If | ${get_framesize} < ${1522}
+| | ... | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Set interfaces in path in 3-node circular topology up
+| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid}
+| | And Configure L2 tag rewrite method on interfaces
+| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2}
+| | ... | ${tag_rewrite}
+| | And Connect interfaces and VLAN sub-interfaces using L2XC
+| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1}
+| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2}
+| | Then Traffic should pass with maximum rate | ${perf_trial_duration}
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1t1c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=1 | rxq=1 | framesize=${64}
+
+| tc02-1518B-1t1c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 1518B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=1 | rxq=1 | framesize=${1518}
+
+| tc03-9000B-1t1c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 9000B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=1 | rxq=1 | framesize=${9000}
+
+| tc04-IMIX-1t1c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\
+| | ... | throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | IMIX | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=1 | rxq=1 | framesize=IMIX_v4_1
+
+| tc05-64B-2t2c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=2 | rxq=1 | framesize=${64}
+
+| tc06-1518B-2t2c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 1518B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=2 | rxq=1 | framesize=${1518}
+
+| tc07-9000B-2t2c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 9000B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=2 | rxq=1 | framesize=${9000}
+
+| tc08-IMIX-2t2c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\
+| | ... | throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | IMIX | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=2 | rxq=1 | framesize=IMIX_v4_1
+
+| tc09-64B-4t4c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=4 | rxq=2 | framesize=${64}
+
+| tc10-1518B-4t4c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 1518B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=4 | rxq=2 | framesize=${1518}
+
+| tc11-9000B-4t4c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\
+| | ... | throughput test.
+| | ...
+| | [Tags] | 9000B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=4 | rxq=2 | framesize=${9000}
+
+| tc12-IMIX-4t4c-dot1q-l2xcbase-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\
+| | ... | throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | IMIX | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for L2XC dot1q-l2xcbase
+| | wt=4 | rxq=2 | framesize=IMIX_v4_1