Add dot1q-l2[bd|xc]base-[ndrpdr|mrr] perf tests for 2-node topology

Jira: CSIT-1284

Change-Id: I8ce4ffc76adf55bf9a8423077b8639601c560c87
Signed-off-by: Jan Gelety <jgelety@cisco.com>

16 files changed, 1231 insertions, 128 deletions

diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.robot
index 6613cb16a2..b3425719e2 100644
--- a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.robot
@@ -28,23 +28,22 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *Raw results L2BD test cases with 802.1q test cases*
+| Documentation | *Raw results L2BD with IEEE 802.1Q test cases*
 | ...
 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.\
-| ... | 802.1q tagging is applied on link between DUT1 and DUT2.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\
-| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC
-| ... | X520 Niantic by Intel.
+| ... | domain and MAC learning enabled. DUT1 and DUT2 are tested with 2p10GE\
+| ... | NIC X520 Niantic by Intel.
 | ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
 | ... | at line rate and reports total received/sent packets over trial period.\
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 254 flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses are matching MAC addresses of the TG node\
-| ... | interfaces.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
@@ -62,8 +61,8 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2BD config with VLAN.
-| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
 | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
 | | ... | trial throughput test.
 | | ...
@@ -80,7 +79,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize} | overhead=${overhead}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in a 3-node circular topology
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
 | | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-ndrpdr.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-ndrpdr.robot
index 4706c1ec36..cafebdb6d0 100644
--- a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-ndrpdr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-ndrpdr.robot
@@ -29,27 +29,25 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *RFC2544: Pkt throughput L2BD test cases with 802.1q test\
-| ... | cases*
+| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases*
 | ...
 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.\
-| ... | 802.1q tagging is applied on link between DUT1 and DUT2.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\
-| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC
-| ... | X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 254 flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses are matching MAC addresses of the TG node\
-| ... | interfaces.
+| ... | domain and MAC learning enabled. DUT1 and DUT2 are tested with 2p10GE\
+| ... | NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
@@ -67,9 +65,9 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2BD config with VLAN.
-| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
-| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.
 | | ...
 | | ... | *Arguments:*
 | | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
@@ -87,7 +85,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize} | overhead=${overhead}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in a 3-node circular topology
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
 | | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
 | | Then Find NDR and PDR intervals using optimized search
 | | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-mrr.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-mrr.robot
index 0d91c61dcb..3da3ad3dac 100644
--- a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-mrr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-mrr.robot
@@ -29,22 +29,21 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *Raw results L2XC with 802.1q test cases*
+| Documentation | *Raw results L2XC with IEEE 802.1Q test cases*
 | ...
 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q\
-| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross-\
-| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | connect. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
 | ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
 | ... | at line rate and reports total received/sent packets over trial period.\
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 253 flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses are matching MAC addresses of the TG node\
-| ... | interfaces.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
@@ -59,8 +58,8 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2XC config with VLAN dot1q with ${phy_cores} phy
-| | ... | core(s).
+| | ... | [Cfg] Each DUT runs L2XC config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
 | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
 | | ... | trial throughput test.
 | | ...
diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrpdr.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrpdr.robot
index 191cfdb7f2..32a5f2c795 100644
--- a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrpdr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrpdr.robot
@@ -30,25 +30,24 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *RFC2544: Pkt throughput L2XC with 802.1q test cases*
+| Documentation | *RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases*
 | ...
 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q\
-| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross-\
-| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 253 flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses are matching MAC addresses of the TG node\
-| ... | interfaces.
+| ... | connect. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
@@ -63,9 +62,9 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2XC config with VLAN dot1q with ${phy_cores} phy
-| | ... | core(s).
-| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ... | [Cfg] Each DUT runs L2XC config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.
 | | ...
 | | ... | *Arguments:*
 | | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
diff --git a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot
index d034b1fd9f..e6269f7861 100644
--- a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot
@@ -28,23 +28,22 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *Raw results L2BD test cases with 802.1q test cases*
+| Documentation | *Raw results L2BD with IEEE 802.1Q test cases*
 | ...
 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.\
-| ... | 802.1q tagging is applied on link between DUT1 and DUT2.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\
-| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC
-| ... | X710 by Intel.
+| ... | domain and MAC learning enabled. DUT1 and DUT2 are tested with 2p10GE\
+| ... | NIC X710 by Intel.
 | ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
 | ... | at line rate and reports total received/sent packets over trial period.\
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 254 flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses are matching MAC addresses of the TG node\
-| ... | interfaces.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
@@ -62,8 +61,8 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2BD config with VLAN with ${phy_cores} phy
-| | ... | core(s).
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
 | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
 | | ... | trial throughput test.
 | | ...
@@ -80,7 +79,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize} | overhead=${overhead}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in a 3-node circular topology
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
 | | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
diff --git a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-ndrpdr.robot b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-ndrpdr.robot
index 76a552a90f..0b1ed19aeb 100644
--- a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-ndrpdr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-ndrpdr.robot
@@ -29,26 +29,25 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *RFC2544: Pkt throughput L2BD test cases with 802.1q*
+| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases*
 | ...
 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.\
-| ... | 802.1q tagging is applied on link between DUT1 and DUT2.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\
-| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC
-| ... | X710 by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 254 flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses are matching MAC addresses of the TG node\
-| ... | interfaces.
+| ... | domain and MAC learning enabled. DUT1 and DUT2 are tested with 2p10GE\
+| ... | NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
@@ -66,9 +65,9 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2BD config with VLAN with ${phy_cores} phy
-| | ... | core(s).
-| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.
 | | ...
 | | ... | *Arguments:*
 | | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
@@ -86,7 +85,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize} | overhead=${overhead}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in a 3-node circular topology
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
 | | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
 | | Then Find NDR and PDR intervals using optimized search
 | | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
diff --git a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-mrr.robot b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-mrr.robot
index 5d143f36b5..6061adc577 100644
--- a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-mrr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-mrr.robot
@@ -29,22 +29,21 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *Raw results L2XC with 802.1q test cases*
+| Documentation | *Raw results L2XC with IEEE 802.1Q test cases*
 | ...
 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q\
-| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross-\
-| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
+| ... | connect. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
 | ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
 | ... | at line rate and reports total received/sent packets over trial period.\
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 253 flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses are matching MAC addresses of the TG node\
-| ... | interfaces.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
@@ -59,8 +58,8 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2XC config with VLAN dot1q with ${phy_cores} phy
-| | ... | core(s).
+| | ... | [Cfg] Each DUT runs L2XC config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
 | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
 | | ... | trial throughput test.
 | | ...
diff --git a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-ndrpdr.robot b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-ndrpdr.robot
index 0bf0d59930..c27941156a 100644
--- a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-ndrpdr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2xcbase-ndrpdr.robot
@@ -30,25 +30,24 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *RFC2544: Pkt throughput L2XC with 802.1q test cases*
+| Documentation | *RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases*
 | ...
 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q\
-| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross-\
-| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 253 flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses are matching MAC addresses of the TG node\
-| ... | interfaces.
+| ... | connect. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
@@ -63,8 +62,8 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2XC config with VLAN dot1q with ${phy_cores} phy
-| | ... | core(s).
+| | ... | [Cfg] Each DUT runs L2XC config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
 | | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
 | | ...
 | | ... | *Arguments:*
diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot
new file mode 100644
index 0000000000..3489910cdb
--- /dev/null
+++ b/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot
@@ -0,0 +1,133 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | BASE | DOT1Q | L2BDMACLRN
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X710
+| ...
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results L2BD with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# X710-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Bridge domain IDs
+| ${bd_id1}= | 1
+| ${bd_id2}= | 2
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize} | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-ndrpdr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-ndrpdr.robot
new file mode 100644
index 0000000000..07c774df2c
--- /dev/null
+++ b/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-ndrpdr.robot
@@ -0,0 +1,139 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | BASE | DOT1Q | L2BDMACLRN
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X710
+| ...
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUT1. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# X710-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Bridge domain IDs
+| ${bd_id1}= | 1
+| ${bd_id2}= | 2
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize} | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2xcbase-mrr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2xcbase-mrr.robot
new file mode 100644
index 0000000000..bdf6575562
--- /dev/null
+++ b/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2xcbase-mrr.robot
@@ -0,0 +1,136 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/l2/tagging.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | L2XCFWD | BASE | DOT1Q
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X710
+| ...
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results L2XC with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross- connect.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# X710-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2XC config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize} | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | And Set interfaces in path up
+| | When Initialize VLAN dot1q sub-interfaces in circular topology
+| | ... | ${dut1} | ${dut1_if2} | SUB_ID=${subid}
+| | And Configure L2 tag rewrite method on interfaces
+| | ... | ${dut1} | ${subif_index_1} | TAG_REWRITE_METHOD=${tag_rewrite}
+| | And Connect interfaces and VLAN sub-interfaces using L2XC
+| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-l2xcbase-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-l2xcbase-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-l2xcbase-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-l2xcbase-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-l2xcbase-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-l2xcbase-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-l2xcbase-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-l2xcbase-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-l2xcbase-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-l2xcbase-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-l2xcbase-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-l2xcbase-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2xcbase-ndrpdr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2xcbase-ndrpdr.robot
new file mode 100644
index 0000000000..c82e63ad22
--- /dev/null
+++ b/tests/vpp/perf/l2/2n1l-10ge2p1x710-dot1q-l2xcbase-ndrpdr.robot
@@ -0,0 +1,141 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/l2/tagging.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | L2XCFWD | BASE | DOT1Q
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X710
+| ...
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross- connect.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# X710-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2XC config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize} | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize VLAN dot1q sub-interfaces in circular topology
+| | ... | ${dut1} | ${dut1_if2} | SUB_ID=${subid}
+| | And Configure L2 tag rewrite method on interfaces
+| | ... | ${dut1} | ${subif_index_1} | TAG_REWRITE_METHOD=${tag_rewrite}
+| | And Connect interfaces and VLAN sub-interfaces using L2XC
+| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-mrr.robot
new file mode 100644
index 0000000000..283ab6b10d
--- /dev/null
+++ b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-mrr.robot
@@ -0,0 +1,137 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | BASE | DOT1Q | L2BDMACLRN
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L2 | Intel-XXV710
+| ...
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results L2BD  with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT1 is tested with 2p25GE NIC XXV710 by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+# Bridge domain IDs
+| ${bd_id1}= | 1
+| ${bd_id2}= | 2
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | ... | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-ndrpdr.robot b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-ndrpdr.robot
new file mode 100644
index 0000000000..0934bc1f2b
--- /dev/null
+++ b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-ndrpdr.robot
@@ -0,0 +1,143 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | BASE | DOT1Q | L2BDMACLRN
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L2 | Intel-XXV710
+| ...
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT1 is tested with 2p25GE NIC XXV710 by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUT1. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+# Bridge domain IDs
+| ${bd_id1}= | 1
+| ${bd_id2}= | 2
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | ... | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2xcbase-mrr.robot b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2xcbase-mrr.robot
new file mode 100644
index 0000000000..be570f5893
--- /dev/null
+++ b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2xcbase-mrr.robot
@@ -0,0 +1,139 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/l2/tagging.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | L2XCFWD | BASE | DOT1Q
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L2 | Intel-XXV710
+| ...
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results L2XC with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross- connect.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2XC config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | ... | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | And Set interfaces in path up
+| | When Initialize VLAN dot1q sub-interfaces in circular topology
+| | ... | ${dut1} | ${dut1_if2} | SUB_ID=${subid}
+| | And Configure L2 tag rewrite method on interfaces
+| | ... | ${dut1} | ${subif_index_1} | TAG_REWRITE_METHOD=${tag_rewrite}
+| | And Connect interfaces and VLAN sub-interfaces using L2XC
+| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-l2xcbase-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-l2xcbase-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-l2xcbase-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-l2xcbase-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-l2xcbase-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-l2xcbase-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-l2xcbase-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-l2xcbase-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-l2xcbase-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-l2xcbase-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-l2xcbase-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-l2xcbase-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2xcbase-ndrpdr.robot b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2xcbase-ndrpdr.robot
new file mode 100644
index 0000000000..5b01304b98
--- /dev/null
+++ b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2xcbase-ndrpdr.robot
@@ -0,0 +1,144 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/l2/tagging.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | L2XCFWD | BASE | DOT1Q
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L2 | Intel-XXV710
+| ...
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross- connect.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2XC config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | ... | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize VLAN dot1q sub-interfaces in circular topology
+| | ... | ${dut1} | ${dut1_if2} | SUB_ID=${subid}
+| | And Configure L2 tag rewrite method on interfaces
+| | ... | ${dut1} | ${subif_index_1} | TAG_REWRITE_METHOD=${tag_rewrite}
+| | And Connect interfaces and VLAN sub-interfaces using L2XC
+| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-l2xcbase-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}