VPP link bonding - lacp mode

CSIT-1072
CSIT-1083
CSIT-1084

Change-Id: Icaf0e09af633d301306a84251f47822e95b411a2
Signed-off-by: Jan Gelety <jgelety@cisco.com>

1 files changed, 262 insertions, 0 deletions

diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x710-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x710-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.robot
new file mode 100644
index 0000000000..50fbecaaa1
--- /dev/null
+++ b/tests/vpp/perf/vm_vhost/10ge2p1x710-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.robot
@@ -0,0 +1,262 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.QemuUtils
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | DOT1Q | L2XCFWD | BASE | VHOST | 1VM
+| ... | VHOST_1024 | LBOND | LBOND_VPP| LBOND_MODE_LACP | LBOND_LB_L34
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 3-node performance topology with DUT's NIC model | L2
+| ... | Intel-X520-DA2
+| ... | AND | Set up performance test suite with LACP mode link bonding
+| ...
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd
+| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs}
+| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs}
+| ...
+| Documentation | *Raw results L2XC test cases with vhost and vpp link bonding*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q
+| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with VPP
+| ... | link bonding (mode LACP, transmit policy l34) on link between DUT1 and
+| ... | DUT2 and L2 cross- connect. Qemu Guest is connected to VPP via
+| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting
+| ... | vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory.
+| ... | Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main
+| ... | core and 4 cores dedicated for io), forwarding mode is set to io,
+| ... | rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710
+| ... | Fortville by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
+| ... | at line rate and reports total received/sent packets over trial period.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+
+*** Variables ***
+| ${perf_qemu_qsz}= | 1024
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${vlan_overhead}= | ${4}
+# Link bonding config
+| ${bond_mode}= | lacp
+| ${lb_mode}= | l34
+# Socket names
+| ${sock1}= | /tmp/sock-1
+| ${sock2}= | /tmp/sock-2
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254
+
+*** Keywords ***
+| Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread, ${wt} phy\
+| | ... | core, ${rxq} receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Arguments] | ${framesize} | ${wt} | ${rxq}
+| | ...
+| | # Test Variables required for test and test teardown
+| | Set Test Variable | ${framesize}
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | ${max_rate}= | Calculate pps | ${s_limit}
+| | ... | ${get_framesize + ${vlan_overhead}}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Set Test Variable | ${dut1_vm_refs}
+| | Set Test Variable | ${dut2_vm_refs}
+| | ${jumbo_frames}= | Set Variable If
+| | ... | ${get_framesize + ${vlan_overhead}} < ${1522} | ${False} | ${True}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add VLAN Strip Offload switch off between DUTs in 3-node single link topology
+| | And Run Keyword If | ${get_framesize + ${vlan_overhead}} < ${1522}
+| | ... | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 xconnect with Vhost-User and VLAN with VPP link bonding in 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite} | ${bond_mode}
+| | ... | ${lb_mode}
+| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | ... | jumbo_frames=${jumbo_frames}
+| | And Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | ... | jumbo_frames=${jumbo_frames}
+| | And Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And All Vpp Interfaces Ready Wait | ${nodes}
+| | Then Traffic should pass with maximum rate | ${perf_trial_duration}
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1t1c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=${64} | wt=1 | rxq=1
+
+| tc02-1518B-1t1c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Tags] | 1518B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=${1518} | wt=1 | rxq=1
+
+| tc03-9000B-1t1c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Tags] | 9000B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=${9000} | wt=1 | rxq=1
+
+| tc04-IMIX-1t1c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single\
+| | ... | trial throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | IMIX | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=IMIX_v4_1 | wt=1 | rxq=1
+
+| tc05-64B-2t2c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=${64} | wt=2 | rxq=1
+
+| tc06-1518B-2t2c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Tags] | 1518B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=${1518} | wt=2 | rxq=1
+
+| tc07-9000B-2t2c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Tags] | 9000B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=${9000} | wt=2 | rxq=1
+
+| tc08-IMIX-2t2c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single\
+| | ... | trial throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | IMIX | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=IMIX_v4_1 | wt=2 | rxq=1
+
+| tc09-64B-4t4c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=${64} | wt=4 | rxq=2
+
+| tc10-1518B-4t4c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Tags] | 1518B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=${1518} | wt=4 | rxq=2
+
+| tc11-9000B-4t4c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Tags] | 9000B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=${9000} | wt=4 | rxq=2
+
+| tc12-IMIX-4t4c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\
+| | ... | cores, 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single\
+| | ... | trial throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | IMIX | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for 1lbvpp-dot1q-l2xcbase-eth-2vhostvr1024-1vm
+| | framesize=IMIX_v4_1 | wt=4 | rxq=2