CSIT-778: Add mac-ip binding acl l2bd perf test

Change-Id: Iaced68458b0e4070f861be7854ee428ae8ca4e13
Signed-off-by: Jan Gelety <jgelety@cisco.com>

9 files changed, 1593 insertions, 0 deletions

diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdrdisc.robot
new file mode 100644
index 0000000000..3d8b90c438
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdrdisc.robot
@@ -0,0 +1,177 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | FEATURE | MACIP | ACL_STATELESS
+| ... | IACL | ACL10 | 100_FLOWS
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with MACIP ACL
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
+| ... | Required MACIP ACL rules are applied to input paths of both DUT1\
+| ... | interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, ${flows_per_dir} flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${no_hit_aces_number}= | 10
+| ${flows_per_dir}= | 100
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${ip_step}= | ${1}
+| ${src_mac_start}= | 01:02:03:04:05:06
+| ${src_mac_step}= | ${1000}
+| ${src_mac_mask}= | 00:00:00:00:00:00
+| ${tg_stream1_mac}= | ca:fe:00:00:00:00
+| ${tg_stream2_mac}= | fa:ce:00:00:00:00
+| ${tg_mac_mask}= | ff:ff:ff:ff:ff:80
+| ${tg_stream1_subnet}= | 10.0.0.0/24
+| ${tg_stream2_subnet}= | 20.0.0.0/24
+
+# traffic profile
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc100ip4src100
+
+*** Keywords ***
+| Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | ...
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc02-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc03-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc04-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc05-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc06-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR
diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdrdisc.robot
new file mode 100644
index 0000000000..b66148841e
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdrdisc.robot
@@ -0,0 +1,177 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | FEATURE | MACIP | ACL_STATELESS
+| ... | IACL | ACL10 | 100k_FLOWS
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with MACIP ACL
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
+| ... | Required MACIP ACL rules are applied to input paths of both DUT1\
+| ... | interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, ${flows_per_dir} flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${no_hit_aces_number}= | 10
+| ${flows_per_dir}= | 100k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${ip_step}= | ${1}
+| ${src_mac_start}= | 01:02:03:04:05:06
+| ${src_mac_step}= | ${1000}
+| ${src_mac_mask}= | 00:00:00:00:00:00
+| ${tg_stream1_mac}= | ca:fe:00:00:00:00
+| ${tg_stream2_mac}= | fa:ce:00:00:00:00
+| ${tg_mac_mask}= | ff:ff:ff:fe:00:00
+| ${tg_stream1_subnet}= | 10.0.0.0/15
+| ${tg_stream2_subnet}= | 20.0.0.0/15
+
+# traffic profile
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc100kip4src100k
+
+*** Keywords ***
+| Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | ...
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc02-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc03-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc04-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc05-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc06-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR
diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdrdisc.robot
new file mode 100644
index 0000000000..21639a8e21
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdrdisc.robot
@@ -0,0 +1,177 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | FEATURE | MACIP | ACL_STATELESS
+| ... | IACL | ACL10 | 10k_FLOWS
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with MACIP ACL
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
+| ... | Required MACIP ACL rules are applied to input paths of both DUT1\
+| ... | interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, ${flows_per_dir} flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${no_hit_aces_number}= | 10
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${ip_step}= | ${1}
+| ${src_mac_start}= | 01:02:03:04:05:06
+| ${src_mac_step}= | ${1000}
+| ${src_mac_mask}= | 00:00:00:00:00:00
+| ${tg_stream1_mac}= | ca:fe:00:00:00:00
+| ${tg_stream2_mac}= | fa:ce:00:00:00:00
+| ${tg_mac_mask}= | ff:ff:ff:ff:c0:00
+| ${tg_stream1_subnet}= | 10.0.0.0/18
+| ${tg_stream2_subnet}= | 20.0.0.0/18
+
+# traffic profile
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc10kip4src10k
+
+*** Keywords ***
+| Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | ...
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc02-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc03-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc04-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc05-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc06-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR
diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdrdisc.robot
new file mode 100644
index 0000000000..c415358e9c
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdrdisc.robot
@@ -0,0 +1,177 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | FEATURE | MACIP | ACL_STATELESS
+| ... | IACL | ACL1 | 100_FLOWS
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with MACIP ACL
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
+| ... | Required MACIP ACL rules are applied to input paths of both DUT1\
+| ... | interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, ${flows_per_dir} flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 100
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${ip_step}= | ${1}
+| ${src_mac_start}= | 01:02:03:04:05:06
+| ${src_mac_step}= | ${1000}
+| ${src_mac_mask}= | 00:00:00:00:00:00
+| ${tg_stream1_mac}= | ca:fe:00:00:00:00
+| ${tg_stream2_mac}= | fa:ce:00:00:00:00
+| ${tg_mac_mask}= | ff:ff:ff:ff:ff:80
+| ${tg_stream1_subnet}= | 10.0.0.0/24
+| ${tg_stream2_subnet}= | 20.0.0.0/24
+
+# traffic profile
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc100ip4src100
+
+*** Keywords ***
+| Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | ...
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc02-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc03-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc04-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc05-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc06-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR
diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdrdisc.robot
new file mode 100644
index 0000000000..f0c345bef3
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdrdisc.robot
@@ -0,0 +1,177 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | FEATURE | MACIP | ACL_STATELESS
+| ... | IACL | ACL1 | 100k_FLOWS
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with MACIP ACL
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
+| ... | Required MACIP ACL rules are applied to input paths of both DUT1\
+| ... | interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, ${flows_per_dir} flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 100k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${ip_step}= | ${1}
+| ${src_mac_start}= | 01:02:03:04:05:06
+| ${src_mac_step}= | ${1000}
+| ${src_mac_mask}= | 00:00:00:00:00:00
+| ${tg_stream1_mac}= | ca:fe:00:00:00:00
+| ${tg_stream2_mac}= | fa:ce:00:00:00:00
+| ${tg_mac_mask}= | ff:ff:ff:fe:00:00
+| ${tg_stream1_subnet}= | 10.0.0.0/15
+| ${tg_stream2_subnet}= | 20.0.0.0/15
+
+# traffic profile
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc100kip4src100k
+
+*** Keywords ***
+| Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | ...
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc02-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc03-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc04-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc05-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc06-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR
diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdrdisc.robot
new file mode 100644
index 0000000000..ee059797ca
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdrdisc.robot
@@ -0,0 +1,177 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | FEATURE | MACIP | ACL_STATELESS
+| ... | IACL | ACL1 | 10k_FLOWS
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with MACIP ACL
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
+| ... | Required MACIP ACL rules are applied to input paths of both DUT1\
+| ... | interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, ${flows_per_dir} flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${ip_step}= | ${1}
+| ${src_mac_start}= | 01:02:03:04:05:06
+| ${src_mac_step}= | ${1000}
+| ${src_mac_mask}= | 00:00:00:00:00:00
+| ${tg_stream1_mac}= | ca:fe:00:00:00:00
+| ${tg_stream2_mac}= | fa:ce:00:00:00:00
+| ${tg_mac_mask}= | ff:ff:ff:ff:c0:00
+| ${tg_stream1_subnet}= | 10.0.0.0/18
+| ${tg_stream2_subnet}= | 20.0.0.0/18
+
+# traffic profile
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc10kip4src10k
+
+*** Keywords ***
+| Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | ...
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc02-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc03-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc04-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc05-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc06-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR
diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdrdisc.robot
new file mode 100644
index 0000000000..043d9ec4f5
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdrdisc.robot
@@ -0,0 +1,177 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | FEATURE | MACIP | ACL_STATELESS
+| ... | IACL | ACL50 | 100_FLOWS
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with MACIP ACL
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
+| ... | Required MACIP ACL rules are applied to input paths of both DUT1\
+| ... | interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, ${flows_per_dir} flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 100
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${ip_step}= | ${1}
+| ${src_mac_start}= | 01:02:03:04:05:06
+| ${src_mac_step}= | ${1000}
+| ${src_mac_mask}= | 00:00:00:00:00:00
+| ${tg_stream1_mac}= | ca:fe:00:00:00:00
+| ${tg_stream2_mac}= | fa:ce:00:00:00:00
+| ${tg_mac_mask}= | ff:ff:ff:ff:ff:80
+| ${tg_stream1_subnet}= | 10.0.0.0/24
+| ${tg_stream2_subnet}= | 20.0.0.0/24
+
+# traffic profile
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc100ip4src100
+
+*** Keywords ***
+| Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | ...
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc02-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc03-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc04-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc05-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc06-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR
diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdrdisc.robot
new file mode 100644
index 0000000000..4519685a8d
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdrdisc.robot
@@ -0,0 +1,177 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | FEATURE | MACIP | ACL_STATELESS
+| ... | IACL | ACL50 | 100k_FLOWS
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with MACIP ACL
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
+| ... | Required MACIP ACL rules are applied to input paths of both DUT1\
+| ... | interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, ${flows_per_dir} flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 100k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${ip_step}= | ${1}
+| ${src_mac_start}= | 01:02:03:04:05:06
+| ${src_mac_step}= | ${1000}
+| ${src_mac_mask}= | 00:00:00:00:00:00
+| ${tg_stream1_mac}= | ca:fe:00:00:00:00
+| ${tg_stream2_mac}= | fa:ce:00:00:00:00
+| ${tg_mac_mask}= | ff:ff:ff:fe:00:00
+| ${tg_stream1_subnet}= | 10.0.0.0/15
+| ${tg_stream2_subnet}= | 20.0.0.0/15
+
+# traffic profile
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc100kip4src100k
+
+*** Keywords ***
+| Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | ...
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc02-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc03-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc04-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc05-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc06-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR
diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdrdisc.robot
new file mode 100644
index 0000000000..94aeaa57d9
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdrdisc.robot
@@ -0,0 +1,177 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | FEATURE | MACIP | ACL_STATELESS
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with MACIP ACL
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
+| ... | Required MACIP ACL rules are applied to input paths of both DUT1\
+| ... | interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, ${flows_per_dir} flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${ip_step}= | ${1}
+| ${src_mac_start}= | 01:02:03:04:05:06
+| ${src_mac_step}= | ${1000}
+| ${src_mac_mask}= | 00:00:00:00:00:00
+| ${tg_stream1_mac}= | ca:fe:00:00:00:00
+| ${tg_stream2_mac}= | fa:ce:00:00:00:00
+| ${tg_mac_mask}= | ff:ff:ff:ff:c0:00
+| ${tg_stream1_subnet}= | 10.0.0.0/18
+| ${tg_stream2_subnet}= | 20.0.0.0/18
+
+# traffic profile
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc10kip4src10k
+
+*** Keywords ***
+| Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | ...
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc02-64B-1t1c-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc03-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc04-64B-2t2c-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR
+
+| tc05-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR
+
+| tc06-64B-4t4c-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with MACIP ACL with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for L2 Bridge Domain with MACIP ACLs
+| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR