Create ip4scale tests for 2-node topology

Jira: CSIT-1174

Change-Id: I46944a3bc0f508d80c8c944dab0190925ebe21f5
Signed-off-by: Jan Gelety <jgelety@cisco.com>

24 files changed, 1722 insertions, 138 deletions

diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale200k-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale200k-mrr.robot
index 9579381dec..589c8aab1b 100644
--- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale200k-mrr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale200k-mrr.robot
@@ -29,18 +29,18 @@
 | ...
 | Documentation | *Raw results IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -73,7 +73,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale200k-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale200k-ndrpdr.robot
index 3b4aa816d3..b3894e81fc 100644
--- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale200k-ndrpdr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale200k-ndrpdr.robot
@@ -30,21 +30,21 @@
 | ...
 | Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -79,7 +79,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Find NDR and PDR intervals using optimized search
 | | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale20k-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale20k-mrr.robot
index 9c1583fbde..dede46bb8d 100644
--- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale20k-mrr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale20k-mrr.robot
@@ -29,18 +29,18 @@
 | ...
 | Documentation | *Raw results IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -72,7 +72,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale20k-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale20k-ndrpdr.robot
index 63f7003012..c215a58d50 100644
--- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale20k-ndrpdr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale20k-ndrpdr.robot
@@ -30,21 +30,21 @@
 | ...
 | Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -78,7 +78,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Find NDR and PDR intervals using optimized search
 | | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale2m-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale2m-mrr.robot
index 038dfa1f40..3c5f5c6383 100644
--- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale2m-mrr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale2m-mrr.robot
@@ -29,18 +29,18 @@
 | ...
 | Documentation | *Raw results IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -73,7 +73,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale2m-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale2m-ndrpdr.robot
index 40a4923eac..fb621d5c17 100644
--- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale2m-ndrpdr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4scale2m-ndrpdr.robot
@@ -30,21 +30,21 @@
 | ...
 | Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -79,7 +79,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Find NDR and PDR intervals using optimized search
 | | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
diff --git a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale200k-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale200k-mrr.robot
index 7215aa23fc..acfeb5bd9d 100644
--- a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale200k-mrr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale200k-mrr.robot
@@ -29,18 +29,18 @@
 | ...
 | Documentation | *Raw results IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X710 by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -73,7 +73,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
diff --git a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale200k-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale200k-ndrpdr.robot
index 0c09691951..c25f0c2872 100644
--- a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale200k-ndrpdr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale200k-ndrpdr.robot
@@ -30,21 +30,21 @@
 | ...
 | Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X710 by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -79,7 +79,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Find NDR and PDR intervals using optimized search
 | | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
diff --git a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale20k-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale20k-mrr.robot
index 3ee50448bb..22b145c6ba 100644
--- a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale20k-mrr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale20k-mrr.robot
@@ -29,18 +29,18 @@
 | ...
 | Documentation | *Raw results IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X710 by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -73,7 +73,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
diff --git a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale20k-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale20k-ndrpdr.robot
index 4ef934f7af..2b5667a351 100644
--- a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale20k-ndrpdr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale20k-ndrpdr.robot
@@ -30,21 +30,21 @@
 | ...
 | Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X710 by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -79,7 +79,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Find NDR and PDR intervals using optimized search
 | | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
diff --git a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale2m-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale2m-mrr.robot
index 7e9e9774b4..27a05ea69f 100644
--- a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale2m-mrr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale2m-mrr.robot
@@ -29,18 +29,18 @@
 | ...
 | Documentation | *Raw results IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X710 by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -73,7 +73,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
diff --git a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale2m-ndrpdr.robot b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale2m-ndrpdr.robot
index 86de7c4dd9..825dd06d8d 100644
--- a/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale2m-ndrpdr.robot
+++ b/tests/vpp/perf/ip4/10ge2p1x710-ethip4-ip4scale2m-ndrpdr.robot
@@ -30,21 +30,21 @@
 | ...
 | Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested\
 | ... | with 2p10GE NIC X710 by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
@@ -79,7 +79,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | When Initialize IPv4 forwarding with scaling in circular topology
 | | ... | ${rts_per_flow}
 | | Then Find NDR and PDR intervals using optimized search
 | | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale200k-mrr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale200k-mrr.robot
new file mode 100644
index 0000000000..96e22ba01a
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale200k-mrr.robot
@@ -0,0 +1,128 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | SCALE | FIB_200k
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x100k static IPv4 /32 route entries. DUT1 is tested with 2p10GE NIC\
+| ... | X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${100000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale200k-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale200k-ndrpdr.robot
new file mode 100644
index 0000000000..1302992f74
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale200k-ndrpdr.robot
@@ -0,0 +1,134 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | SCALE | FIB_200k
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x100k static IPv4 /32 route entries. DUT1 is tested with 2p10GE NIC\
+| ... | X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${100000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale20k-mrr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale20k-mrr.robot
new file mode 100644
index 0000000000..24e21fb8cf
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale20k-mrr.robot
@@ -0,0 +1,128 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | SCALE | FIB_20k
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x10k static IPv4 /32 route entries. DUT1 is tested with 2p10GE NIC\
+| ... | X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${10000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale20k-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale20k-ndrpdr.robot
new file mode 100644
index 0000000000..80c727d5dd
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale20k-ndrpdr.robot
@@ -0,0 +1,134 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | SCALE | FIB_20k
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x10k static IPv4 /32 route entries. DUT1 is tested with 2p10GE NIC\
+| ... | X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${10000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale2m-mrr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale2m-mrr.robot
new file mode 100644
index 0000000000..50bf0b93bf
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale2m-mrr.robot
@@ -0,0 +1,128 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | SCALE | FIB_2M
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x1M static IPv4 /32 route entries. DUT1 is tested with 2p10GE NIC\
+| ... | X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${1000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale2m-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale2m-ndrpdr.robot
new file mode 100644
index 0000000000..bf98f56ab6
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4-ip4scale2m-ndrpdr.robot
@@ -0,0 +1,134 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | SCALE | FIB_2M
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x1M static IPv4 /32 route entries. DUT1 is tested with 2p10GE NIC\
+| ... | X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${rts_per_flow}= | ${1000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale200k-mrr.robot b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale200k-mrr.robot
new file mode 100644
index 0000000000..0b3c8fc4fe
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale200k-mrr.robot
@@ -0,0 +1,130 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | SCALE | FIB_200k
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-XXV710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x100k static IPv4 /32 route entries. DUT1 is tested with 2p25GE NIC\
+| ... | XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+| ${rts_per_flow}= | ${100000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale200k-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale200k-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale200k-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale200k-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale200k-ndrpdr.robot
new file mode 100644
index 0000000000..f2df05c1e0
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale200k-ndrpdr.robot
@@ -0,0 +1,136 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | SCALE | FIB_200k
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-XXV710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x100k static IPv4 /32 route entries. DUT1 is tested with 2p25GE NIC\
+| ... | XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 100k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+| ${rts_per_flow}= | ${100000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale200k-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale20k-mrr.robot b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale20k-mrr.robot
new file mode 100644
index 0000000000..64973a60bf
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale20k-mrr.robot
@@ -0,0 +1,130 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | SCALE | FIB_20k
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-XXV710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x10k static IPv4 /32 route entries. DUT1 is tested with 2p25GE NIC\
+| ... | XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+| ${rts_per_flow}= | ${10000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale20k-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale20k-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale20k-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale20k-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale20k-ndrpdr.robot
new file mode 100644
index 0000000000..61ce559ce4
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale20k-ndrpdr.robot
@@ -0,0 +1,136 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | SCALE | FIB_20k
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-XXV710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x10k static IPv4 /32 route entries. DUT1 is tested with 2p25GE NIC\
+| ... | XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 10k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+| ${rts_per_flow}= | ${10000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale20k-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale2m-mrr.robot b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale2m-mrr.robot
new file mode 100644
index 0000000000..509b4ba124
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale2m-mrr.robot
@@ -0,0 +1,130 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | SCALE | FIB_2M
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-XXV710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x1M static IPv4 /32 route entries. DUT1 is tested with 2p25GE NIC\
+| ... | XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+| ${rts_per_flow}= | ${1000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale2m-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale2m-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale2m-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
diff --git a/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale2m-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale2m-ndrpdr.robot
new file mode 100644
index 0000000000..0e64c7b107
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4scale2m-ndrpdr.robot
@@ -0,0 +1,136 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | SCALE | FIB_2M
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-XXV710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | 2x1M static IPv4 /32 route entries. DUT1 is tested with 2p25GE NIC\
+| ... | XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 1M flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+| ${rts_per_flow}= | ${1000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding with scaling in circular topology
+| | ... | ${rts_per_flow}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4scale2m-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}