CSIT-614: Create PDRCHK tests

 - CSIT-630: 10Ge2P1X520-Ethip4-Ip4Scale2M-pdrchk
 - CSIT-638: 10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-pdrchk

Change-Id: I314d87acbd5906946acad97224f71c39a8cf1e04
Signed-off-by: Tibor Frank <tifrank@cisco.com>

3 files changed, 381 insertions, 9 deletions

diff --git a/tests/perf/10ge2p1x520-ethip4-ip4scale2m-pdrchk.robot b/tests/perf/10ge2p1x520-ethip4-ip4scale2m-pdrchk.robot
new file mode 100644
index 0000000000..c983066b5b
--- /dev/null
+++ b/tests/perf/10ge2p1x520-ethip4-ip4scale2m-pdrchk.robot
@@ -0,0 +1,185 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PDRCHK
+| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | SCALE | FIB_2M
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| Test Teardown | Tear down performance pdrchk test
+| ...
+| Documentation | *Reference PDR throughput IPv4 routing verify test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG verifies throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. Ref-PDR value is periodically updated acording
+| ... | to formula: ref-PDR = 0.9x PDR, where PDR is found in RFC2544 long
+| ... | performance tests for the same DUT configuration. Test packets are
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3
+| ... | flow-groups (flow-group per direction, 1M flows per flow-group) with
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61
+| ... | and static payload. Incrementing of IP.dst (IPv4 destination address)
+| ... | field is applied to both streams.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${rts_per_flow}= | ${1000000}
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip4-ip4dst${rts_per_flow}
+
+*** Keywords ***
+| Check PDR for IPv4 routing
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with ${wt} thread, ${wt} phy\
+| | ... | core, ${rxq} receive queue per NIC port.
+| | ... | [Ver] Verify ref-PDR for ${framesize} Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Arguments] | ${framesize} | ${rate} | ${wt} | ${rxq}
+| | ...
+| | # Test Variables required for test and test teardown
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${rate}
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Run Keyword If | ${get_framesize} < ${1522}
+| | ... | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize IPv4 forwarding with scaling in 3-node circular topology
+| | ... | ${rts_per_flow}
+| | Then Traffic should pass with partial loss | ${perf_trial_duration}
+| | ... | ${rate} | ${framesize} | ${traffic_profile}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-ethip4-ip4scale2m-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-PDR for 64 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check PDR for IPv4 routing
+| | framesize=${64} | rate=3.0mpps | wt=1 | rxq=1
+
+| tc02-1518B-1t1c-ethip4-ip4scale2m-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\
+| | ... | trial throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 1518B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check PDR for IPv4 routing
+| | framesize=${1518} | rate=600000pps | wt=1 | rxq=1
+
+| tc03-9000B-1t1c-ethip4-ip4scale2m-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 9000B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check PDR for IPv4 routing
+| | framesize=${9000} | rate=100000pps | wt=1 | rxq=1
+
+| tc04-64B-2t2c-ethip4-ip4scale2m-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-PDR for 64 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check PDR for IPv4 routing
+| | framesize=${64} | rate=7.0mpps | wt=2 | rxq=1
+
+| tc05-1518B-2t2c-ethip4-ip4scale2m-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 1518B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check PDR for IPv4 routing
+| | framesize=${1518} | rate=500000pps | wt=2 | rxq=1
+
+| tc06-9000B-2t2c-ethip4-ip4scale2m-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-PDR for 9000 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 9000B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check PDR for IPv4 routing
+| | framesize=${9000} | rate=100000pps | wt=2 | rxq=1
+
+| tc07-64B-4t4c-ethip4-ip4scale2m-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Verify ref-PDR for 64 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check PDR for IPv4 routing
+| | framesize=${64} | rate=10.0mpps | wt=4 | rxq=2
+
+| tc08-1518B-4t4c-ethip4-ip4scale2m-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 1518B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check PDR for IPv4 routing
+| | framesize=${1518} | rate=500000pps | wt=4 | rxq=2
+
+| tc09-9000B-4t4c-ethip4-ip4scale2m-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Verify ref-PDR for 9000 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 9000B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check PDR for IPv4 routing
+| | framesize=${9000} | rate=100000pps | wt=4 | rxq=2
diff --git a/tests/perf/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-pdrchk.robot b/tests/perf/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-pdrchk.robot
new file mode 100644
index 0000000000..cd9aa6b107
--- /dev/null
+++ b/tests/perf/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-pdrchk.robot
@@ -0,0 +1,186 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PDRCHK
+| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance pdrchk test
+| ...
+| Documentation | *RFC2544: Packet throughput L2BD with VXLANoIPv4 test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain on TG-DUTn.
+| ... | Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge
+| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2.
+| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG verifies throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. Ref-PDR value is periodically updated acording
+| ... | to formula: ref-PDR = 0.9x PDR, where PDR is found in RFC2544 long
+| ... | performance tests for the same DUT configuration. Test packets are
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3
+| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61
+| ... | and generated payload. MAC addresses are matching MAC addresses of the
+| ... | TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348.
+
+*** Variables ***
+| ${vxlan_overhead} | ${50}
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254
+
+*** Keywords ***
+| Check PDR for L2BD forwarding with VXLAN over IPv4
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC config config with ${wt} thread, ${wt} phy\
+| | ... | core, ${rxq} receive queue per NIC port.
+| | ... | [Ver] Verify ref-PDR for ${framesize} Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Arguments] | ${framesize} | ${rate} | ${wt} | ${rxq}
+| | ...
+| | # Test Variables required for test and test teardown
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${rate}
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Run Keyword If | ${get_framesize} < ${1522}
+| | ... | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | And Initialize L2 bridge domain with VXLANoIPv4 in 3-node circular topology
+| | Then Traffic should pass with partial loss | ${perf_trial_duration}
+| | ... | ${rate} | ${framesize} | ${traffic_profile}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-64B-1t1c-ethip4vxlan-l2bdbasemaclrn-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 64B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check PDR for L2BD forwarding with VXLAN over IPv4
+| | framesize=${64 + ${vxlan_overhead}} | rate=2.4mpps | wt=1 | rxq=1
+
+| tc02-1518B-1t1c-ethip4vxlan-l2bdbasemaclrn-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 1518B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check PDR for L2BD forwarding with VXLAN over IPv4
+| | framesize=${1518 + ${vxlan_overhead}} | rate=700000pps | wt=1 | rxq=1
+
+| tc03-9000B-1t1c-ethip4vxlan-l2bdbasemaclrn-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 9000B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check PDR for L2BD forwarding with VXLAN over IPv4
+| | framesize=${9000 + ${vxlan_overhead}} | rate=100000pps | wt=1 | rxq=1
+
+| tc04-64B-2t2c-ethip4vxlan-l2bdbasemaclrn-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 64B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check PDR for L2BD forwarding with VXLAN over IPv4
+| | framesize=${64 + ${vxlan_overhead}} | rate=5.2mpps | wt=2 | rxq=1
+
+| tc05-1518B-2t2c-ethip4vxlan-l2bdbasemaclrn-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 1518B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check PDR for L2BD forwarding with VXLAN over IPv4
+| | framesize=${1518 + ${vxlan_overhead}} | rate=650000pps | wt=2 | rxq=1
+
+| tc06-9000B-2t2c-ethip4vxlan-l2bdbasemaclrn-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 9000B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check PDR for L2BD forwarding with VXLAN over IPv4
+| | framesize=${9000 + ${vxlan_overhead}} | rate=100000pps | wt=2 | rxq=1
+
+| tc07-64B-4t4c-ethip4vxlan-l2bdbasemaclrn-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queue per NIC port.
+| | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 64B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check PDR for L2BD forwarding with VXLAN over IPv4
+| | framesize=${64 + ${vxlan_overhead}} | rate=6.5mpps | wt=4 | rxq=2
+
+| tc08-1518B-4t4c-ethip4vxlan-l2bdbasemaclrn-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queue per NIC port.
+| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 1518B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check PDR for L2BD forwarding with VXLAN over IPv4
+| | framesize=${1518 + ${vxlan_overhead}} | rate=700000pps | wt=4 | rxq=2
+
+| tc09-9000B-4t4c-ethip4vxlan-l2bdbasemaclrn-pdrchk
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queue per NIC port.
+| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\
+| | ... | throughput test at 2x ${rate}.
+| | ...
+| | [Tags] | 9000B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check PDR for L2BD forwarding with VXLAN over IPv4
+| | framesize=${9000 + ${vxlan_overhead}} | rate=100000pps | wt=4 | rxq=2
diff --git a/tests/perf/10ge2p1x520-ethip4vxlan-l2xcbase-pdrchk.robot b/tests/perf/10ge2p1x520-ethip4vxlan-l2xcbase-pdrchk.robot
index 8d8eb096cc..0c7cd0d2a7 100644
--- a/tests/perf/10ge2p1x520-ethip4vxlan-l2xcbase-pdrchk.robot
+++ b/tests/perf/10ge2p1x520-ethip4vxlan-l2xcbase-pdrchk.robot
@@ -47,6 +47,7 @@
 | ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348.
 
 *** Variables ***
+| ${vxlan_overhead} | ${50}
 # Traffic profile:
 | ${traffic_profile} | trex-sl-3n-ethip4-ip4src254
 
@@ -86,7 +87,7 @@
 | | [Tags] | 64B | 1T1C | STHREAD
 | | ...
 | | [Template] | Check PDR for L2 xconnect with VXLAN over IPv4
-| | framesize=${64} | rate=2.4mpps | wt=1 | rxq=1
+| | framesize=${64 + ${vxlan_overhead}} | rate=2.0mpps | wt=1 | rxq=1
 
 | tc02-1518B-1t1c-ethip4vxlan-l2xcbase-pdrchk
 | | [Documentation]
@@ -98,7 +99,7 @@
 | | [Tags] | 1518B | 1T1C | STHREAD
 | | ...
 | | [Template] | Check PDR for L2 xconnect with VXLAN over IPv4
-| | framesize=${1518} | rate=787153pps | wt=1 | rxq=1
+| | framesize=${1518 + ${vxlan_overhead}} | rate=500000pps | wt=1 | rxq=1
 
 | tc03-9000B-1t1c-ethip4vxlan-l2xcbase-pdrchk
 | | [Documentation]
@@ -110,7 +111,7 @@
 | | [Tags] | 9000B | 1T1C | STHREAD
 | | ...
 | | [Template] | Check PDR for L2 xconnect with VXLAN over IPv4
-| | framesize=${9000} | rate=137816pps | wt=1 | rxq=1
+| | framesize=${9000 + ${vxlan_overhead}} | rate=100000pps | wt=1 | rxq=1
 
 | tc04-64B-2t2c-ethip4vxlan-l2xcbase-pdrchk
 | | [Documentation]
@@ -122,7 +123,7 @@
 | | [Tags] | 64B | 2T2C | MTHREAD
 | | ...
 | | [Template] | Check PDR for L2 xconnect with VXLAN over IPv4
-| | framesize=${64} | rate=5.2mpps | wt=2 | rxq=1
+| | framesize=${64 + ${vxlan_overhead}} | rate=5.0mpps | wt=2 | rxq=1
 
 | tc05-1518B-2t2c-ethip4vxlan-l2xcbase-pdrchk
 | | [Documentation]
@@ -134,7 +135,7 @@
 | | [Tags] | 1518B | 2T2C | MTHREAD
 | | ...
 | | [Template] | Check PDR for L2 xconnect with VXLAN over IPv4
-| | framesize=${1518} | rate=787153pps | wt=2 | rxq=1
+| | framesize=${1518 + ${vxlan_overhead}} | rate=500000pps | wt=2 | rxq=1
 
 | tc06-9000B-2t2c-ethip4vxlan-l2xcbase-pdrchk
 | | [Documentation]
@@ -146,7 +147,7 @@
 | | [Tags] | 9000B | 2T2C | MTHREAD
 | | ...
 | | [Template] | Check PDR for L2 xconnect with VXLAN over IPv4
-| | framesize=${9000} | rate=137816pps | wt=2 | rxq=1
+| | framesize=${9000 + ${vxlan_overhead}} | rate=100000pps | wt=2 | rxq=1
 
 | tc07-64B-4t4c-ethip4vxlan-l2xcbase-pdrchk
 | | [Documentation]
@@ -158,7 +159,7 @@
 | | [Tags] | 64B | 4T4C | MTHREAD
 | | ...
 | | [Template] | Check PDR for L2 xconnect with VXLAN over IPv4
-| | framesize=${64} | rate=8.4mpps | wt=4 | rxq=2
+| | framesize=${64 + ${vxlan_overhead}} | rate=6.5mpps | wt=4 | rxq=2
 
 | tc08-1518B-4t4c-ethip4vxlan-l2xcbase-pdrchk
 | | [Documentation]
@@ -170,7 +171,7 @@
 | | [Tags] | 1518B | 4T4C | MTHREAD
 | | ...
 | | [Template] | Check PDR for L2 xconnect with VXLAN over IPv4
-| | framesize=${1518} | rate=787153pps | wt=4 | rxq=2
+| | framesize=${1518 + ${vxlan_overhead}} | rate=500000pps | wt=4 | rxq=2
 
 | tc09-9000B-4t4c-ethip4vxlan-l2xcbase-pdrchk
 | | [Documentation]
@@ -182,4 +183,4 @@
 | | [Tags] | 9000B | 4T4C | MTHREAD
 | | ...
 | | [Template] | Check PDR for L2 xconnect with VXLAN over IPv4
-| | framesize=${9000} | rate=137816pps | wt=4 | rxq=2
+| | framesize=${9000 + ${vxlan_overhead}} | rate=100000pps | wt=4 | rxq=2