CSIT-509: Add perf tests for vlan + l2 + vhost

Change-Id: I65e716b51dd35092c10574ac4580ee4b8bd3b24b
Signed-off-by: Tibor Frank <tifrank@cisco.com>

3 files changed, 1411 insertions, 1 deletions

diff --git a/tests/perf/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc.robot b/tests/perf/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc.robot
new file mode 100644
index 0000000000..028c9e00f9
--- /dev/null
+++ b/tests/perf/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc.robot
@@ -0,0 +1,716 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance.robot
+| Library | resources.libraries.python.QemuUtils
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ...        | NIC_Intel-X520-DA2 | DOT1Q | L2BDMACLRN | BASE | VHOST | VM
+| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | 3-node Performance Suite Teardown
+| Test Setup | Setup all DUTs before test
+| Test Teardown | Run Keywords
+| ...           | Run Keyword If Test Failed
+| ...           | Traffic should pass with no loss | 10
+| ...           | ${min_rate}pps | ${framesize} | 3-node-bridge
+| ...           | fail_on_loss=${False}
+| ...           | AND | Show Vpp Vhost On All DUTs
+| ...           | AND | Remove startup configuration of VPP from all DUTs
+| ...           | AND | Guest VM with dpdk-testpmd Teardown | ${dut1}
+| ...                 | ${dut1_vm_refs}
+| ...           | AND | Guest VM with dpdk-testpmd Teardown | ${dut2}
+| ...                 | ${dut2_vm_refs}
+| Documentation | *RFC2544: Packet throughput L2BD test cases with vhost*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. 802.1q
+| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-
+| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via
+| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting
+| ... | vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M
+| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores
+| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to
+| ... | io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520
+| ... | Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using either binary search or linear search
+| ... | algorithms with configured starting rate and final step that determines
+| ... | throughput measurement resolution. Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static
+| ... | payload. MAC addresses are matching MAC addresses of the TG node
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${vlan_overhead}= | ${4}
+# X520-DA2 bandwidth limit
+| ${s_limit} | ${10000000000}
+# Socket names
+| ${bd_id1}= | 1
+| ${bd_id2}= | 2
+| ${sock1}= | /tmp/sock-1-${bd_id1}
+| ${sock2}= | /tmp/sock-1-${bd_id2}
+
+
+*** Test Cases ***
+| tc01-64B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc02-64B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc03-1518B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc04-1518B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc05-IMIX-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc06-IMIX-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps, LT=0.5%.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc07-64B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 2T2C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc08-64B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc09-1518B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 2T2C | STHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc10-1518B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc11-IMIX-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 2T2C | STHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc12-IMIX-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 2T2C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc13-64B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 4T4C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc14-64B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc15-1518B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 4T4C | STHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc16-1518B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc17-IMIX-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 4T4C | STHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc18-IMIX-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps, LT=0.5%.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 4T4C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 bridge domains with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
+| | ... | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
diff --git a/tests/perf/10ge2p1x520-dot1q-l2xcbase-eth-2vhost-1vm-ndrdisc.robot b/tests/perf/10ge2p1x520-dot1q-l2xcbase-eth-2vhost-1vm-ndrdisc.robot
new file mode 100644
index 0000000000..46bbc3be41
--- /dev/null
+++ b/tests/perf/10ge2p1x520-dot1q-l2xcbase-eth-2vhost-1vm-ndrdisc.robot
@@ -0,0 +1,694 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance.robot
+| Library | resources.libraries.python.NodePath
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ...        | NIC_Intel-X520-DA2 | DOT1Q | L2XCFWD | BASE | VHOST | VM
+| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | 3-node Performance Suite Teardown
+| Test Setup | Setup all DUTs before test
+| Test Teardown | Run Keywords
+| ...           | Run Keyword If Test Failed
+| ...           | Traffic should pass with no loss | 10
+| ...           | ${min_rate}pps | ${framesize} | 3-node-bridge
+| ...           | fail_on_loss=${False}
+| ...           | AND | Show Vpp Vhost On All DUTs
+| ...           | AND |  Remove startup configuration of VPP from all DUTs
+| ...           | AND | Guest VM with dpdk-testpmd Teardown | ${dut1}
+| ...                 | ${dut1_vm_refs}
+| ...           | AND | Guest VM with dpdk-testpmd Teardown | ${dut2}
+| ...                 | ${dut2_vm_refs}
+| Documentation | *RFC2544: Pkt throughput L2XC test cases with vhost*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q
+| ... | tagging is applied on link between DUT1 and DUT2.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross-
+| ... | connect. Qemu Guest is connected to VPP via vhost-user interfaces.
+| ... | Guest is running DPDK testpmd interconnecting vhost-user interfaces
+| ... | using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using
+| ... | socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores
+| ... | dedicated for io), forwarding mode is set to io, rxd/txd=256,
+| ... | burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using either binary search or linear search
+| ... | algorithms with configured starting rate and final step that determines
+| ... | throughput measurement resolution. Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static
+| ... | payload. MAC addresses are matching MAC addresses of the TG node
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${vlan_overhead}= | ${4}
+# Socket names
+| ${sock1}= | /tmp/sock-1
+| ${sock2}= | /tmp/sock-2
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+*** Test Cases ***
+| tc01-64B-1t1c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc02-64B-1t1c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc03-1518B-1t1c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc04-1518B-1t1c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc05-IMIX-1t1c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc06-IMIX-1t1c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps, LT=0.5%.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc07-64B-2t2c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 2T2C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc08-64B-2t2c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc09-1518B-2t2c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 2T2C | STHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc10-1518B-2t2c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc11-IMIX-2t2c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 2T2C | STHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc12-IMIX-2t2c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
+| | ... | 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps, LT=0.5%.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 2T2C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc13-64B-4t4c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 4T4C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc14-64B-4t4c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc15-1518B-4t4c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps.
+| | ...
+| | [Tags] | 4T4C | STHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc16-1518B-4t4c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 10kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + ${vlan_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+| tc17-IMIX-4t4c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 4T4C | STHREAD | NDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| tc18-IMIX-4t4c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,\
+| | ... | 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for IMIX_v4_1 framesize using binary search start at\
+| | ... | 10GE linerate, step 10kpps, LT=0.5%.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | ...
+| | [Tags] | 4T4C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${avg_framesize}= | Set Variable | ${357.833}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${avg_framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${dut1_vm_refs}= | Create Dictionary
+| | ${dut2_vm_refs}= | Create Dictionary
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When L2 xconnect with Vhost-User and VLAN initialized in a 3-node circular topology
+| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
+| | ${vm1}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
+| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
+| | ${vm2}= | And Guest VM with dpdk-testpmd connected via vhost-user is setup
+| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
+| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Setup scheduler policy for VPP on all DUTs
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
+| | ... | ${threshold} | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
diff --git a/tests/perf/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc.robot b/tests/perf/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc.robot
index 65203f62a7..bcb211fcbd 100644
--- a/tests/perf/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc.robot
+++ b/tests/perf/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc.robot
@@ -173,7 +173,7 @@
 | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
 | | ... | ${threshold}
 
-| tc04-64B-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
+| tc04-1518B-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
 | | [Documentation]
 | | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
 | | ... | 1 receive queue per NIC port.