diff options
10 files changed, 1415 insertions, 0 deletions
diff --git a/GPL/traffic_profiles/trex/trex-stl-ethip4udp-1024u63p-udir.py b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-1024u63p-udir.py new file mode 100644 index 0000000000..bf10bf08d6 --- /dev/null +++ b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-1024u63p-udir.py @@ -0,0 +1,118 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +"""Stream profile for T-rex traffic generator. + +Stream profile: + - One stream sent in directions 0 --> 1. + - Packet: ETH / IP / UDP + - Direction 0 --> 1: + - Source IP address range: 192.168.0.0 - 192.168.3.255 + - Destination IP address range: 20.0.0.0 - 20.0.3.255 + - Source UDP port range: 1024 - 1086 + - Destination UDP port range: 8080 +""" + +from trex.stl.api import * +from profile_trex_stateless_base_class import TrafficStreamsBaseClass + + +class TrafficStreams(TrafficStreamsBaseClass): + """Stream profile.""" + + def __init__(self): + """Initialization and setting of streams' parameters.""" + + super(TrafficStreamsBaseClass, self).__init__() + + # IPs used in packet headers. + self.p1_src_start_ip = u"192.168.0.0" + self.p1_src_end_ip = u"192.168.3.255" + self.p1_dst_start_ip = u"20.0.0.0" + self.p1_dst_end_ip = u"20.0.3.255" + + # UDP ports used in packet headers. + self.p1_src_start_udp_port = 1024 + self.p1_src_end_udp_port = 1086 + self.p1_dst_start_udp_port = 8080 + self.p1_dst_end_udp_port = 8080 + + def define_packets(self): + """Defines the packets to be sent from the traffic generator. + + Packet definition: | ETH | IP | UDP | + + :returns: Packets to be sent from the traffic generator. + :rtype: tuple + """ + + # Direction 0 --> 1 + base_pkt_a = ( + Ether() / + IP( + src=self.p1_src_start_ip, + dst=self.p1_dst_start_ip, + proto=17 + ) / + UDP( + sport=self.p1_src_start_udp_port, + dport=self.p1_dst_start_udp_port + ) + ) + + base_pkt_b = ( + Ether() + ) + + # Direction 0 --> 1 + vm1 = STLVM() + vm1.var(name="sIP", + min_value=self.p1_src_start_ip, + max_value=self.p1_src_end_ip, + size=4, + op="inc", + next_var="sport") + vm1.var(name="sport", + min_value=self.p1_src_start_udp_port, + max_value=self.p1_src_end_udp_port, + size=2, + op="inc") + vm1.var(name="dIP", + min_value=self.p1_dst_start_ip, + max_value=self.p1_dst_end_ip, + size=4, + op="inc") + vm1.var(name="dport", + min_value=self.p1_dst_start_udp_port, + max_value=self.p1_dst_end_udp_port, + size=2, + op="inc") + vm1.write(fv_name="sIP", pkt_offset="IP.src") + vm1.write(fv_name="sport", pkt_offset="UDP.sport") + vm1.write(fv_name="dIP", pkt_offset="IP.dst") + vm1.write(fv_name="dport", pkt_offset="UDP.dport") + vm1.fix_chksum(offset='IP') + + vm2 = STLVM() + + return base_pkt_a, base_pkt_b, vm1, vm2 + +def register(): + """Register this traffic profile to T-rex. + + Do not change this function. + + :return: Traffic streams. + :rtype: Object + """ + return TrafficStreams() diff --git a/GPL/traffic_profiles/trex/trex-stl-ethip4udp-16384u63p-udir.py b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-16384u63p-udir.py new file mode 100644 index 0000000000..2f6718438c --- /dev/null +++ b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-16384u63p-udir.py @@ -0,0 +1,118 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +"""Stream profile for T-rex traffic generator. + +Stream profile: + - One stream sent in directions 0 --> 1. + - Packet: ETH / IP / UDP + - Direction 0 --> 1: + - Source IP address range: 192.168.0.0 - 192.168.63.255 + - Destination IP address range: 20.0.0.0 - 20.0.63.255 + - Source UDP port range: 1024 - 1086 + - Destination UDP port range: 8080 +""" + +from trex.stl.api import * +from profile_trex_stateless_base_class import TrafficStreamsBaseClass + + +class TrafficStreams(TrafficStreamsBaseClass): + """Stream profile.""" + + def __init__(self): + """Initialization and setting of streams' parameters.""" + + super(TrafficStreamsBaseClass, self).__init__() + + # IPs used in packet headers. + self.p1_src_start_ip = u"192.168.0.0" + self.p1_src_end_ip = u"192.168.63.255" + self.p1_dst_start_ip = u"20.0.0.0" + self.p1_dst_end_ip = u"20.0.63.255" + + # UDP ports used in packet headers. + self.p1_src_start_udp_port = 1024 + self.p1_src_end_udp_port = 1086 + self.p1_dst_start_udp_port = 8080 + self.p1_dst_end_udp_port = 8080 + + def define_packets(self): + """Defines the packets to be sent from the traffic generator. + + Packet definition: | ETH | IP | UDP | + + :returns: Packets to be sent from the traffic generator. + :rtype: tuple + """ + + # Direction 0 --> 1 + base_pkt_a = ( + Ether() / + IP( + src=self.p1_src_start_ip, + dst=self.p1_dst_start_ip, + proto=17 + ) / + UDP( + sport=self.p1_src_start_udp_port, + dport=self.p1_dst_start_udp_port + ) + ) + + base_pkt_b = ( + Ether() + ) + + # Direction 0 --> 1 + vm1 = STLVM() + vm1.var(name="sIP", + min_value=self.p1_src_start_ip, + max_value=self.p1_src_end_ip, + size=4, + op="inc", + next_var="sport") + vm1.var(name="sport", + min_value=self.p1_src_start_udp_port, + max_value=self.p1_src_end_udp_port, + size=2, + op="inc") + vm1.var(name="dIP", + min_value=self.p1_dst_start_ip, + max_value=self.p1_dst_end_ip, + size=4, + op="inc") + vm1.var(name="dport", + min_value=self.p1_dst_start_udp_port, + max_value=self.p1_dst_end_udp_port, + size=2, + op="inc") + vm1.write(fv_name="sIP", pkt_offset="IP.src") + vm1.write(fv_name="sport", pkt_offset="UDP.sport") + vm1.write(fv_name="dIP", pkt_offset="IP.dst") + vm1.write(fv_name="dport", pkt_offset="UDP.dport") + vm1.fix_chksum(offset='IP') + + vm2 = STLVM() + + return base_pkt_a, base_pkt_b, vm1, vm2 + +def register(): + """Register this traffic profile to T-rex. + + Do not change this function. + + :return: Traffic streams. + :rtype: Object + """ + return TrafficStreams() diff --git a/GPL/traffic_profiles/trex/trex-stl-ethip4udp-262144u63p-udir.py b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-262144u63p-udir.py new file mode 100644 index 0000000000..200ca40e7a --- /dev/null +++ b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-262144u63p-udir.py @@ -0,0 +1,118 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +"""Stream profile for T-rex traffic generator. + +Stream profile: + - One stream sent in directions 0 --> 1. + - Packet: ETH / IP / UDP + - Direction 0 --> 1: + - Source IP address range: 192.168.0.0 - 192.171.255.255 + - Destination IP address range: 20.0.0.0 - 20.3.255.255 + - Source UDP port range: 1024 - 1086 + - Destination UDP port range: 8080 +""" + +from trex.stl.api import * +from profile_trex_stateless_base_class import TrafficStreamsBaseClass + + +class TrafficStreams(TrafficStreamsBaseClass): + """Stream profile.""" + + def __init__(self): + """Initialization and setting of streams' parameters.""" + + super(TrafficStreamsBaseClass, self).__init__() + + # IPs used in packet headers. + self.p1_src_start_ip = u"192.168.0.0" + self.p1_src_end_ip = u"192.171.255.255" + self.p1_dst_start_ip = u"20.0.0.0" + self.p1_dst_end_ip = u"20.3.255.255" + + # UDP ports used in packet headers. + self.p1_src_start_udp_port = 1024 + self.p1_src_end_udp_port = 1086 + self.p1_dst_start_udp_port = 8080 + self.p1_dst_end_udp_port = 8080 + + def define_packets(self): + """Defines the packets to be sent from the traffic generator. + + Packet definition: | ETH | IP | UDP | + + :returns: Packets to be sent from the traffic generator. + :rtype: tuple + """ + + # Direction 0 --> 1 + base_pkt_a = ( + Ether() / + IP( + src=self.p1_src_start_ip, + dst=self.p1_dst_start_ip, + proto=17 + ) / + UDP( + sport=self.p1_src_start_udp_port, + dport=self.p1_dst_start_udp_port + ) + ) + + base_pkt_b = ( + Ether() + ) + + # Direction 0 --> 1 + vm1 = STLVM() + vm1.var(name="sIP", + min_value=self.p1_src_start_ip, + max_value=self.p1_src_end_ip, + size=4, + op="inc", + next_var="sport") + vm1.var(name="sport", + min_value=self.p1_src_start_udp_port, + max_value=self.p1_src_end_udp_port, + size=2, + op="inc") + vm1.var(name="dIP", + min_value=self.p1_dst_start_ip, + max_value=self.p1_dst_end_ip, + size=4, + op="inc") + vm1.var(name="dport", + min_value=self.p1_dst_start_udp_port, + max_value=self.p1_dst_end_udp_port, + size=2, + op="inc") + vm1.write(fv_name="sIP", pkt_offset="IP.src") + vm1.write(fv_name="sport", pkt_offset="UDP.sport") + vm1.write(fv_name="dIP", pkt_offset="IP.dst") + vm1.write(fv_name="dport", pkt_offset="UDP.dport") + vm1.fix_chksum(offset='IP') + + vm2 = STLVM() + + return base_pkt_a, base_pkt_b, vm1, vm2 + +def register(): + """Register this traffic profile to T-rex. + + Do not change this function. + + :return: Traffic streams. + :rtype: Object + """ + return TrafficStreams() diff --git a/GPL/traffic_profiles/trex/trex-stl-ethip4udp-4096u63p-udir.py b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-4096u63p-udir.py new file mode 100644 index 0000000000..f0d553d7c4 --- /dev/null +++ b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-4096u63p-udir.py @@ -0,0 +1,118 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +"""Stream profile for T-rex traffic generator. + +Stream profile: + - One stream sent in directions 0 --> 1. + - Packet: ETH / IP / UDP + - Direction 0 --> 1: + - Source IP address range: 192.168.0.0 - 192.168.15.255 + - Destination IP address range: 20.0.0.0 - 20.0.15.255 + - Source UDP port range: 1024 - 1086 + - Destination UDP port range: 8080 +""" + +from trex.stl.api import * +from profile_trex_stateless_base_class import TrafficStreamsBaseClass + + +class TrafficStreams(TrafficStreamsBaseClass): + """Stream profile.""" + + def __init__(self): + """Initialization and setting of streams' parameters.""" + + super(TrafficStreamsBaseClass, self).__init__() + + # IPs used in packet headers. + self.p1_src_start_ip = u"192.168.0.0" + self.p1_src_end_ip = u"192.168.15.255" + self.p1_dst_start_ip = u"20.0.0.0" + self.p1_dst_end_ip = u"20.0.15.255" + + # UDP ports used in packet headers. + self.p1_src_start_udp_port = 1024 + self.p1_src_end_udp_port = 1086 + self.p1_dst_start_udp_port = 8080 + self.p1_dst_end_udp_port = 8080 + + def define_packets(self): + """Defines the packets to be sent from the traffic generator. + + Packet definition: | ETH | IP | UDP | + + :returns: Packets to be sent from the traffic generator. + :rtype: tuple + """ + + # Direction 0 --> 1 + base_pkt_a = ( + Ether() / + IP( + src=self.p1_src_start_ip, + dst=self.p1_dst_start_ip, + proto=17 + ) / + UDP( + sport=self.p1_src_start_udp_port, + dport=self.p1_dst_start_udp_port + ) + ) + + base_pkt_b = ( + Ether() + ) + + # Direction 0 --> 1 + vm1 = STLVM() + vm1.var(name="sIP", + min_value=self.p1_src_start_ip, + max_value=self.p1_src_end_ip, + size=4, + op="inc", + next_var="sport") + vm1.var(name="sport", + min_value=self.p1_src_start_udp_port, + max_value=self.p1_src_end_udp_port, + size=2, + op="inc") + vm1.var(name="dIP", + min_value=self.p1_dst_start_ip, + max_value=self.p1_dst_end_ip, + size=4, + op="inc") + vm1.var(name="dport", + min_value=self.p1_dst_start_udp_port, + max_value=self.p1_dst_end_udp_port, + size=2, + op="inc") + vm1.write(fv_name="sIP", pkt_offset="IP.src") + vm1.write(fv_name="sport", pkt_offset="UDP.sport") + vm1.write(fv_name="dIP", pkt_offset="IP.dst") + vm1.write(fv_name="dport", pkt_offset="UDP.dport") + vm1.fix_chksum(offset='IP') + + vm2 = STLVM() + + return base_pkt_a, base_pkt_b, vm1, vm2 + +def register(): + """Register this traffic profile to T-rex. + + Do not change this function. + + :return: Traffic streams. + :rtype: Object + """ + return TrafficStreams() diff --git a/GPL/traffic_profiles/trex/trex-stl-ethip4udp-65536u63p-udir.py b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-65536u63p-udir.py new file mode 100644 index 0000000000..2b2de3abe3 --- /dev/null +++ b/GPL/traffic_profiles/trex/trex-stl-ethip4udp-65536u63p-udir.py @@ -0,0 +1,118 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +"""Stream profile for T-rex traffic generator. + +Stream profile: + - One stream sent in directions 0 --> 1. + - Packet: ETH / IP / UDP + - Direction 0 --> 1: + - Source IP address range: 192.168.0.0 - 192.168.255.255 + - Destination IP address range: 20.0.255.255 - 20.0.255.255 + - Source UDP port range: 1024 - 1086 + - Destination UDP port range: 8080 +""" + +from trex.stl.api import * +from profile_trex_stateless_base_class import TrafficStreamsBaseClass + + +class TrafficStreams(TrafficStreamsBaseClass): + """Stream profile.""" + + def __init__(self): + """Initialization and setting of streams' parameters.""" + + super(TrafficStreamsBaseClass, self).__init__() + + # IPs used in packet headers. + self.p1_src_start_ip = u"192.168.0.0" + self.p1_src_end_ip = u"192.168.255.255" + self.p1_dst_start_ip = u"20.0.0.0" + self.p1_dst_end_ip = u"20.0.255.255" + + # UDP ports used in packet headers. + self.p1_src_start_udp_port = 1024 + self.p1_src_end_udp_port = 1086 + self.p1_dst_start_udp_port = 8080 + self.p1_dst_end_udp_port = 8080 + + def define_packets(self): + """Defines the packets to be sent from the traffic generator. + + Packet definition: | ETH | IP | UDP | + + :returns: Packets to be sent from the traffic generator. + :rtype: tuple + """ + + # Direction 0 --> 1 + base_pkt_a = ( + Ether() / + IP( + src=self.p1_src_start_ip, + dst=self.p1_dst_start_ip, + proto=17 + ) / + UDP( + sport=self.p1_src_start_udp_port, + dport=self.p1_dst_start_udp_port + ) + ) + + base_pkt_b = ( + Ether() + ) + + # Direction 0 --> 1 + vm1 = STLVM() + vm1.var(name="sIP", + min_value=self.p1_src_start_ip, + max_value=self.p1_src_end_ip, + size=4, + op="inc", + next_var="sport") + vm1.var(name="sport", + min_value=self.p1_src_start_udp_port, + max_value=self.p1_src_end_udp_port, + size=2, + op="inc") + vm1.var(name="dIP", + min_value=self.p1_dst_start_ip, + max_value=self.p1_dst_end_ip, + size=4, + op="inc") + vm1.var(name="dport", + min_value=self.p1_dst_start_udp_port, + max_value=self.p1_dst_end_udp_port, + size=2, + op="inc") + vm1.write(fv_name="sIP", pkt_offset="IP.src") + vm1.write(fv_name="sport", pkt_offset="UDP.sport") + vm1.write(fv_name="dIP", pkt_offset="IP.dst") + vm1.write(fv_name="dport", pkt_offset="UDP.dport") + vm1.fix_chksum(offset='IP') + + vm2 = STLVM() + + return base_pkt_a, base_pkt_b, vm1, vm2 + +def register(): + """Register this traffic profile to T-rex. + + Do not change this function. + + :return: Traffic streams. + :rtype: Object + """ + return TrafficStreams() diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr.robot new file mode 100644 index 0000000000..0f83b9ef4b --- /dev/null +++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr.robot @@ -0,0 +1,165 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | NAT44 | UDP_SYN +| ... | NAT44_ENDPOINT_DEPENDENT | BASE | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip4udp-nat44ed-h1024-p63-s64512-udir +| +| Suite Setup | Setup suite topology interfaces | performance +| Suite Teardown | Tear down suite | performance +| Test Setup | Setup test | performance +| Test Teardown | Tear down test | performance | nat-ed +| +| Test Template | Local Template +| +| Documentation | *RFC2544: Pkt throughput NAT44 endpoint-dependent mode +| ... | performance test cases* +| +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\ +| ... | one static IPv4 /${dest_mask} route entries.\ +| ... | DUT1 is tested with ${nic_name}. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contain L4 flows (uni-directional UDP flows) with all packets\ +| ... | containing Ethernet header, IPv4 header with UDP header and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* Benchmarking Methodology\ +| ... | for Network Security Device Performance\ +| ... | (draft-ietf-bmwg-ngfw-performance-03). + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so | nat_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | Intel-X710 +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${osi_layer}= | L3 +| ${overhead}= | ${0} +# IP settings +| ${tg_if1_ip4}= | 10.0.0.2 +| ${tg_if1_mask}= | ${20} +| ${tg_if2_ip4}= | 12.0.0.2 +| ${tg_if2_mask}= | ${20} +| ${dut1_if1_ip4}= | 10.0.0.1 +| ${dut1_if1_mask}= | ${24} +| ${dut1_if2_ip4}= | 12.0.0.1 +| ${dut1_if2_mask}= | ${24} +| ${dest_net}= | 20.0.0.0 +| ${dest_mask}= | ${8} +# NAT settings +| ${nat_mode}= | endpoint-dependent +| ${max_translations_per_thread}= | 64512 +| ${in_net}= | 192.168.0.0 +| ${in_mask}= | ${8} +| ${out_net}= | 68.142.68.0 +| ${out_net_end}= | 68.142.68.0 +| ${out_mask}= | ${32} +# Traffic profile: +| ${traffic_profile}= | trex-stl-ethip4udp-1024u63p-udir + +*** Keywords *** +| Local Template +| | +| | [Documentation] +| | ... | [Cfg] DUT runs NAT44 ${nat_mode} configuration. +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Add NAT to all DUTs | nat_mode=${nat_mode} +| | And Add NAT max translations per thread to all DUTs +| | ... | ${max_translations_per_thread} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Initialize IPv4 forwarding for NAT44 in circular topology +| | And Initialize NAT44 endpoint-dependent mode in circular topology +| | Then Find NDR and PDR intervals using optimized search +| | ... | traffic_directions=${1} + +*** Test Cases *** +| 64B-1c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | 64B | 1C +| | frame_size=${64} | phy_cores=${1} + +| 64B-2c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | 64B | 2C +| | frame_size=${64} | phy_cores=${2} + +| 64B-4c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | 64B | 4C +| | frame_size=${64} | phy_cores=${4} + +| 1518B-1c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | 1518B | 1C +| | frame_size=${1518} | phy_cores=${1} + +| 1518B-2c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | 1518B | 2C +| | frame_size=${1518} | phy_cores=${2} + +| 1518B-4c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | 1518B | 4C +| | frame_size=${1518} | phy_cores=${4} + +| 9000B-1c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | 9000B | 1C +| | frame_size=${9000} | phy_cores=${1} + +| 9000B-2c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | 9000B | 2C +| | frame_size=${9000} | phy_cores=${2} + +| 9000B-4c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | 9000B | 4C +| | frame_size=${9000} | phy_cores=${4} + +| IMIX-1c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | IMIX | 1C +| | frame_size=IMIX_v4_1 | phy_cores=${1} + +| IMIX-2c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | IMIX | 2C +| | frame_size=IMIX_v4_1 | phy_cores=${2} + +| IMIX-4c-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr +| | [Tags] | IMIX | 4C +| | frame_size=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr.robot new file mode 100644 index 0000000000..3007649599 --- /dev/null +++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr.robot @@ -0,0 +1,165 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | NAT44 | UDP_SYN +| ... | NAT44_ENDPOINT_DEPENDENT | BASE | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip4udp-nat44ed-h16384-p63-s1032192-udir +| +| Suite Setup | Setup suite topology interfaces | performance +| Suite Teardown | Tear down suite | performance +| Test Setup | Setup test | performance +| Test Teardown | Tear down test | performance | nat-ed +| +| Test Template | Local Template +| +| Documentation | *RFC2544: Pkt throughput NAT44 endpoint-dependent mode +| ... | performance test cases* +| +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\ +| ... | one static IPv4 /${dest_mask} route entries.\ +| ... | DUT1 is tested with ${nic_name}. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contain L4 flows (un-directional UDP flows) with all packets\ +| ... | containing Ethernet header, IPv4 header with UDP header and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* Benchmarking Methodology\ +| ... | for Network Security Device Performance\ +| ... | (draft-ietf-bmwg-ngfw-performance-03). + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so | nat_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | Intel-X710 +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${osi_layer}= | L3 +| ${overhead}= | ${0} +# IP settings +| ${tg_if1_ip4}= | 10.0.0.2 +| ${tg_if1_mask}= | ${20} +| ${tg_if2_ip4}= | 12.0.0.2 +| ${tg_if2_mask}= | ${20} +| ${dut1_if1_ip4}= | 10.0.0.1 +| ${dut1_if1_mask}= | ${24} +| ${dut1_if2_ip4}= | 12.0.0.1 +| ${dut1_if2_mask}= | ${24} +| ${dest_net}= | 20.0.0.0 +| ${dest_mask}= | ${8} +# NAT settings +| ${nat_mode}= | endpoint-dependent +| ${max_translations_per_thread}= | 1032192 +| ${in_net}= | 192.168.0.0 +| ${in_mask}= | ${18} +| ${out_net}= | 68.142.68.0 +| ${out_net_end}= | 68.142.68.15 +| ${out_mask}= | ${28} +# Traffic profile: +| ${traffic_profile}= | trex-stl-ethip4udp-16384u63p-udir + +*** Keywords *** +| Local Template +| | +| | [Documentation] +| | ... | [Cfg] DUT runs NAT44 ${nat_mode} configuration. +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Add NAT to all DUTs | nat_mode=${nat_mode} +| | And Add NAT max translations per thread to all DUTs +| | ... | ${max_translations_per_thread} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Initialize IPv4 forwarding for NAT44 in circular topology +| | And Initialize NAT44 endpoint-dependent mode in circular topology +| | Then Find NDR and PDR intervals using optimized search +| | ... | traffic_directions=${1} + +*** Test Cases *** +| 64B-1c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | 64B | 1C +| | frame_size=${64} | phy_cores=${1} + +| 64B-2c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | 64B | 2C +| | frame_size=${64} | phy_cores=${2} + +| 64B-4c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | 64B | 4C +| | frame_size=${64} | phy_cores=${4} + +| 1518B-1c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | 1518B | 1C +| | frame_size=${1518} | phy_cores=${1} + +| 1518B-2c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | 1518B | 2C +| | frame_size=${1518} | phy_cores=${2} + +| 1518B-4c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | 1518B | 4C +| | frame_size=${1518} | phy_cores=${4} + +| 9000B-1c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | 9000B | 1C +| | frame_size=${9000} | phy_cores=${1} + +| 9000B-2c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | 9000B | 2C +| | frame_size=${9000} | phy_cores=${2} + +| 9000B-4c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | 9000B | 4C +| | frame_size=${9000} | phy_cores=${4} + +| IMIX-1c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | IMIX | 1C +| | frame_size=IMIX_v4_1 | phy_cores=${1} + +| IMIX-2c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | IMIX | 2C +| | frame_size=IMIX_v4_1 | phy_cores=${2} + +| IMIX-4c-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr +| | [Tags] | IMIX | 4C +| | frame_size=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr.robot new file mode 100644 index 0000000000..22e4cabe7d --- /dev/null +++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr.robot @@ -0,0 +1,165 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | NAT44 | UDP_SYN +| ... | NAT44_ENDPOINT_DEPENDENT | BASE | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip4udp-nat44ed-h262144-p63-s16515072-udir +| +| Suite Setup | Setup suite topology interfaces | performance +| Suite Teardown | Tear down suite | performance +| Test Setup | Setup test | performance +| Test Teardown | Tear down test | performance | nat-ed +| +| Test Template | Local Template +| +| Documentation | *RFC2544: Pkt throughput NAT44 endpoint-dependent mode +| ... | performance test cases* +| +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\ +| ... | one static IPv4 /${dest_mask} route entries.\ +| ... | DUT1 is tested with ${nic_name}. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contain L4 flows (uni-directional UDP flows) with all packets\ +| ... | containing Ethernet header, IPv4 header with UDP header and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* Benchmarking Methodology\ +| ... | for Network Security Device Performance\ +| ... | (draft-ietf-bmwg-ngfw-performance-03). + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so | nat_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | Intel-X710 +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${osi_layer}= | L3 +| ${overhead}= | ${0} +# IP settings +| ${tg_if1_ip4}= | 10.0.0.2 +| ${tg_if1_mask}= | ${20} +| ${tg_if2_ip4}= | 12.0.0.2 +| ${tg_if2_mask}= | ${20} +| ${dut1_if1_ip4}= | 10.0.0.1 +| ${dut1_if1_mask}= | ${24} +| ${dut1_if2_ip4}= | 12.0.0.1 +| ${dut1_if2_mask}= | ${24} +| ${dest_net}= | 20.0.0.0 +| ${dest_mask}= | ${8} +# NAT settings +| ${nat_mode}= | endpoint-dependent +| ${max_translations_per_thread}= | 16515072 +| ${in_net}= | 192.168.0.0 +| ${in_mask}= | ${8} +| ${out_net}= | 68.142.68.0 +| ${out_net_end}= | 68.142.68.255 +| ${out_mask}= | ${24} +# Traffic profile: +| ${traffic_profile}= | trex-stl-ethip4udp-262144u63p-udir + +*** Keywords *** +| Local Template +| | +| | [Documentation] +| | ... | [Cfg] DUT runs NAT44 ${nat_mode} configuration. +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Add NAT to all DUTs | nat_mode=${nat_mode} +| | And Add NAT max translations per thread to all DUTs +| | ... | ${max_translations_per_thread} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Initialize IPv4 forwarding for NAT44 in circular topology +| | And Initialize NAT44 endpoint-dependent mode in circular topology +| | Then Find NDR and PDR intervals using optimized search +| | ... | traffic_directions=${1} + +*** Test Cases *** +| 64B-1c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | 64B | 1C +| | frame_size=${64} | phy_cores=${1} + +| 64B-2c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | 64B | 2C +| | frame_size=${64} | phy_cores=${2} + +| 64B-4c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | 64B | 4C +| | frame_size=${64} | phy_cores=${4} + +| 1518B-1c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | 1518B | 1C +| | frame_size=${1518} | phy_cores=${1} + +| 1518B-2c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | 1518B | 2C +| | frame_size=${1518} | phy_cores=${2} + +| 1518B-4c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | 1518B | 4C +| | frame_size=${1518} | phy_cores=${4} + +| 9000B-1c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | 9000B | 1C +| | frame_size=${9000} | phy_cores=${1} + +| 9000B-2c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | 9000B | 2C +| | frame_size=${9000} | phy_cores=${2} + +| 9000B-4c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | 9000B | 4C +| | frame_size=${9000} | phy_cores=${4} + +| IMIX-1c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | IMIX | 1C +| | frame_size=IMIX_v4_1 | phy_cores=${1} + +| IMIX-2c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | IMIX | 2C +| | frame_size=IMIX_v4_1 | phy_cores=${2} + +| IMIX-4c-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr +| | [Tags] | IMIX | 4C +| | frame_size=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr.robot new file mode 100644 index 0000000000..c075fbfb7c --- /dev/null +++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr.robot @@ -0,0 +1,165 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | NAT44 | UDP_SYN +| ... | NAT44_ENDPOINT_DEPENDENT | BASE | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip4udp-nat44ed-h4096-p63-s258048-udir +| +| Suite Setup | Setup suite topology interfaces | performance +| Suite Teardown | Tear down suite | performance +| Test Setup | Setup test | performance +| Test Teardown | Tear down test | performance | nat-ed +| +| Test Template | Local Template +| +| Documentation | *RFC2544: Pkt throughput NAT44 endpoint-dependent mode +| ... | performance test cases* +| +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\ +| ... | one static IPv4 /${dest_mask} route entries.\ +| ... | DUT1 is tested with ${nic_name}. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contain L4 flows (uni-directional UDP flows) with all packets\ +| ... | containing Ethernet header, IPv4 header with UDP header and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* Benchmarking Methodology\ +| ... | for Network Security Device Performance\ +| ... | (draft-ietf-bmwg-ngfw-performance-03). + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so | nat_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | Intel-X710 +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${osi_layer}= | L3 +| ${overhead}= | ${0} +# IP settings +| ${tg_if1_ip4}= | 10.0.0.2 +| ${tg_if1_mask}= | ${20} +| ${tg_if2_ip4}= | 12.0.0.2 +| ${tg_if2_mask}= | ${20} +| ${dut1_if1_ip4}= | 10.0.0.1 +| ${dut1_if1_mask}= | ${24} +| ${dut1_if2_ip4}= | 12.0.0.1 +| ${dut1_if2_mask}= | ${24} +| ${dest_net}= | 20.0.0.0 +| ${dest_mask}= | ${8} +# NAT settings +| ${nat_mode}= | endpoint-dependent +| ${max_translations_per_thread}= | 258048 +| ${in_net}= | 192.168.0.0 +| ${in_mask}= | ${8} +| ${out_net}= | 68.142.68.0 +| ${out_net_end}= | 68.142.68.3 +| ${out_mask}= | ${30} +# Traffic profile: +| ${traffic_profile}= | trex-stl-ethip4udp-4096u63p-udir + +*** Keywords *** +| Local Template +| | +| | [Documentation] +| | ... | [Cfg] DUT runs NAT44 ${nat_mode} configuration. +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Add NAT to all DUTs | nat_mode=${nat_mode} +| | And Add NAT max translations per thread to all DUTs +| | ... | ${max_translations_per_thread} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Initialize IPv4 forwarding for NAT44 in circular topology +| | And Initialize NAT44 endpoint-dependent mode in circular topology +| | Then Find NDR and PDR intervals using optimized search +| | ... | traffic_directions=${1} + +*** Test Cases *** +| 64B-1c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | 64B | 1C +| | frame_size=${64} | phy_cores=${1} + +| 64B-2c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | 64B | 2C +| | frame_size=${64} | phy_cores=${2} + +| 64B-4c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | 64B | 4C +| | frame_size=${64} | phy_cores=${4} + +| 1518B-1c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | 1518B | 1C +| | frame_size=${1518} | phy_cores=${1} + +| 1518B-2c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | 1518B | 2C +| | frame_size=${1518} | phy_cores=${2} + +| 1518B-4c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | 1518B | 4C +| | frame_size=${1518} | phy_cores=${4} + +| 9000B-1c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | 9000B | 1C +| | frame_size=${9000} | phy_cores=${1} + +| 9000B-2c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | 9000B | 2C +| | frame_size=${9000} | phy_cores=${2} + +| 9000B-4c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | 9000B | 4C +| | frame_size=${9000} | phy_cores=${4} + +| IMIX-1c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | IMIX | 1C +| | frame_size=IMIX_v4_1 | phy_cores=${1} + +| IMIX-2c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | IMIX | 2C +| | frame_size=IMIX_v4_1 | phy_cores=${2} + +| IMIX-4c-ethip4udp-nat44ed-h4096-p63-s258048-udir-ndrpdr +| | [Tags] | IMIX | 4C +| | frame_size=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr.robot new file mode 100644 index 0000000000..c2a67ca0c6 --- /dev/null +++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x710-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr.robot @@ -0,0 +1,165 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | NAT44 | UDP_SYN +| ... | NAT44_ENDPOINT_DEPENDENT | BASE | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip4udp-nat44ed-h65536-p63-s4128768-udir +| +| Suite Setup | Setup suite topology interfaces | performance +| Suite Teardown | Tear down suite | performance +| Test Setup | Setup test | performance +| Test Teardown | Tear down test | performance | nat-ed +| +| Test Template | Local Template +| +| Documentation | *RFC2544: Pkt throughput NAT44 endpoint-dependent mode +| ... | performance test cases* +| +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\ +| ... | one static IPv4 /${dest_mask} route entries.\ +| ... | DUT1 is tested with ${nic_name}. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contain L4 flows (uni-directional UDP flows) with all packets\ +| ... | containing Ethernet header, IPv4 header with UDP header and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* Benchmarking Methodology\ +| ... | for Network Security Device Performance\ +| ... | (draft-ietf-bmwg-ngfw-performance-03). + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so | nat_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | Intel-X710 +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${osi_layer}= | L3 +| ${overhead}= | ${0} +# IP settings +| ${tg_if1_ip4}= | 10.0.0.2 +| ${tg_if1_mask}= | ${20} +| ${tg_if2_ip4}= | 12.0.0.2 +| ${tg_if2_mask}= | ${20} +| ${dut1_if1_ip4}= | 10.0.0.1 +| ${dut1_if1_mask}= | ${24} +| ${dut1_if2_ip4}= | 12.0.0.1 +| ${dut1_if2_mask}= | ${24} +| ${dest_net}= | 20.0.0.0 +| ${dest_mask}= | ${8} +# NAT settings +| ${nat_mode}= | endpoint-dependent +| ${max_translations_per_thread}= | 4128768 +| ${in_net}= | 192.168.0.0 +| ${in_mask}= | ${8} +| ${out_net}= | 68.142.68.0 +| ${out_net_end}= | 68.142.68.63 +| ${out_mask}= | ${26} +# Traffic profile: +| ${traffic_profile}= | trex-stl-ethip4udp-65536u63p-udir + +*** Keywords *** +| Local Template +| | +| | [Documentation] +| | ... | [Cfg] DUT runs NAT44 ${nat_mode} configuration. +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Add NAT to all DUTs | nat_mode=${nat_mode} +| | And Add NAT max translations per thread to all DUTs +| | ... | ${max_translations_per_thread} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Initialize IPv4 forwarding for NAT44 in circular topology +| | And Initialize NAT44 endpoint-dependent mode in circular topology +| | Then Find NDR and PDR intervals using optimized search +| | ... | traffic_directions=${1} + +*** Test Cases *** +| 64B-1c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | 64B | 1C +| | frame_size=${64} | phy_cores=${1} + +| 64B-2c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | 64B | 2C +| | frame_size=${64} | phy_cores=${2} + +| 64B-4c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | 64B | 4C +| | frame_size=${64} | phy_cores=${4} + +| 1518B-1c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | 1518B | 1C +| | frame_size=${1518} | phy_cores=${1} + +| 1518B-2c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | 1518B | 2C +| | frame_size=${1518} | phy_cores=${2} + +| 1518B-4c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | 1518B | 4C +| | frame_size=${1518} | phy_cores=${4} + +| 9000B-1c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | 9000B | 1C +| | frame_size=${9000} | phy_cores=${1} + +| 9000B-2c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | 9000B | 2C +| | frame_size=${9000} | phy_cores=${2} + +| 9000B-4c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | 9000B | 4C +| | frame_size=${9000} | phy_cores=${4} + +| IMIX-1c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | IMIX | 1C +| | frame_size=IMIX_v4_1 | phy_cores=${1} + +| IMIX-2c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | IMIX | 2C +| | frame_size=IMIX_v4_1 | phy_cores=${2} + +| IMIX-4c-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr +| | [Tags] | IMIX | 4C +| | frame_size=IMIX_v4_1 | phy_cores=${4} |