diff options
10 files changed, 1280 insertions, 0 deletions
diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x553-ethip4-ip4base-mrr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x553-ethip4-ip4base-mrr.robot new file mode 100644 index 0000000000..634973faad --- /dev/null +++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x553-ethip4-ip4base-mrr.robot @@ -0,0 +1,124 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X553 | ETH | IP4FWD | BASE | IP4BASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L3 | Intel-X553 +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results IPv4 routing test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 +| ... | routing and two static IPv4 /24 route entries. DUT1 tested with +| ... | 2p10GE NIC X553 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-ethip4-ip4src253 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config.\ +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv4 forwarding in circular topology +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-ethip4-ip4base-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-ethip4-ip4base-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-ethip4-ip4base-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-ethip4-ip4base-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-ethip4-ip4base-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-ethip4-ip4base-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-ethip4-ip4base-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-ethip4-ip4base-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-ethip4-ip4base-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-ethip4-ip4base-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-ethip4-ip4base-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-ethip4-ip4base-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4/2n1l-10ge2p1x553-ethip4-ip4base-ndrpdr.robot b/tests/vpp/perf/ip4/2n1l-10ge2p1x553-ethip4-ip4base-ndrpdr.robot new file mode 100644 index 0000000000..be2fdab166 --- /dev/null +++ b/tests/vpp/perf/ip4/2n1l-10ge2p1x553-ethip4-ip4base-ndrpdr.robot @@ -0,0 +1,130 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X553 | ETH | IP4FWD | BASE | IP4BASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L3 | Intel-X553 +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 +| ... | routing and two static IPv4 /24 route entries. DUT1 tested with +| ... | 2p10GE NIC X553 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using MLRsearch library. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-ethip4-ip4src253 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config.\ +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv4 forwarding in circular topology +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-ethip4-ip4base-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-ethip4-ip4base-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-ethip4-ip4base-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-ethip4-ip4base-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-ethip4-ip4base-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-ethip4-ip4base-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-ethip4-ip4base-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-ethip4-ip4base-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-ethip4-ip4base-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-ethip4-ip4base-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-ethip4-ip4base-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-ethip4-ip4base-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip6/2n1l-10ge2p1x553-ethip6-ip6base-mrr.robot b/tests/vpp/perf/ip6/2n1l-10ge2p1x553-ethip6-ip6base-mrr.robot new file mode 100644 index 0000000000..1c3ea01c00 --- /dev/null +++ b/tests/vpp/perf/ip6/2n1l-10ge2p1x553-ethip6-ip6base-mrr.robot @@ -0,0 +1,125 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X553 | ETH | IP6FWD | BASE | IP6BASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L3 | Intel-X553 +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results IPv6 routing test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv6 routing and two +| ... | static IPv6 /64 route entries. DUT1 tested with 2p10GE NIC X553 by +| ... | Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv6 header and +| ... | static payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-ethip6-ip6src253 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config.\ +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 2-node circular topology +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-78B-1c-ethip6-ip6base-mrr +| | [Tags] | 78B | 1C +| | framesize=${78} | phy_cores=${1} + +| tc02-78B-2c-ethip6-ip6base-mrr +| | [Tags] | 78B | 2C +| | framesize=${78} | phy_cores=${2} + +| tc03-78B-4c-ethip6-ip6base-mrr +| | [Tags] | 78B | 4C +| | framesize=${78} | phy_cores=${4} + +| tc04-1518B-1c-ethip6-ip6base-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-ethip6-ip6base-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-ethip6-ip6base-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-ethip6-ip6base-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-ethip6-ip6base-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-ethip6-ip6base-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-ethip6-ip6base-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-ethip6-ip6base-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-ethip6-ip6base-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip6/2n1l-10ge2p1x553-ethip6-ip6base-ndrpdr.robot b/tests/vpp/perf/ip6/2n1l-10ge2p1x553-ethip6-ip6base-ndrpdr.robot new file mode 100644 index 0000000000..e17e9e1084 --- /dev/null +++ b/tests/vpp/perf/ip6/2n1l-10ge2p1x553-ethip6-ip6base-ndrpdr.robot @@ -0,0 +1,131 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X553 | ETH | IP6FWD | BASE | IP6BASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L3 | Intel-X553 +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *Packet throughput routing test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv6 routing and two +| ... | static IPv6 /64 route entries. DUT1 tested with 2p10GE NIC X553 by +| ... | Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on\ +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ +| ... | (flow-group per direction, 253 flows per flow-group) with\ +| ... | all packets containing Ethernet header,IPv6 header with static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-ethip6-ip6src253 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config.\ +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 2-node circular topology +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-78B-1c-ethip6-ip6base-ndrpdr +| | [Tags] | 78B | 1C +| | framesize=${78} | phy_cores=${1} + +| tc02-78B-2c-ethip6-ip6base-ndrpdr +| | [Tags] | 78B | 2C +| | framesize=${78} | phy_cores=${2} + +| tc03-78B-4c-ethip6-ip6base-ndrpdr +| | [Tags] | 78B | 4C +| | framesize=${78} | phy_cores=${4} + +| tc04-1518B-1c-ethip6-ip6base-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-ethip6-ip6base-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-ethip6-ip6base-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-ethip6-ip6base-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-ethip6-ip6base-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-ethip6-ip6base-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-ethip6-ip6base-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-ethip6-ip6base-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-ethip6-ip6base-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2bdbasemaclrn-mrr.robot new file mode 100644 index 0000000000..cb2e42609f --- /dev/null +++ b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2bdbasemaclrn-mrr.robot @@ -0,0 +1,126 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X553 | ETH | L2BDMACLRN | BASE | L2BDBASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L2 | Intel-X553 +| ... +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge-domain +| ... | and MAC learning enabled. DUT1 tested with 2p10GE NIC +| ... | X553 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-ethip4-ip4src254 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs L2 switching config.\ +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 2-node circular topology +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-eth-l2bdbasemaclrn-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-eth-l2bdbasemaclrn-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-eth-l2bdbasemaclrn-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-eth-l2bdbasemaclrn-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-eth-l2bdbasemaclrn-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-eth-l2bdbasemaclrn-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-eth-l2bdbasemaclrn-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-eth-l2bdbasemaclrn-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-eth-l2bdbasemaclrn-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-eth-l2bdbasemaclrn-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-eth-l2bdbasemaclrn-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-eth-l2bdbasemaclrn-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2bdbasemaclrn-ndrpdr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2bdbasemaclrn-ndrpdr.robot new file mode 100644 index 0000000000..0285ae8eea --- /dev/null +++ b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2bdbasemaclrn-ndrpdr.robot @@ -0,0 +1,132 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X553 | ETH | L2BDMACLRN | BASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L2 | Intel-X553 +| ... +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge-domain +| ... | and MAC learning enabled. DUT1 tested with 2p10GE NIC +| ... | X553 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library\ +| ... | Test packets are generated by TG on\ +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ +| ... | (flow-group per direction, 254 flows per flow-group) with\ +| ... | all packets containing Ethernet header,IPv4 header with static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-2n-ethip4-ip4src254 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs L2 switching config.\ +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 2-node circular topology +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-eth-l2bdbasemaclrn-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2patch-mrr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2patch-mrr.robot new file mode 100644 index 0000000000..dae0de536f --- /dev/null +++ b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2patch-mrr.robot @@ -0,0 +1,125 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X553 | ETH | L2PATCH | BASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L2 | Intel-X553 +| ... +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2patch test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 patch. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 patch\ +| ... | DUT1 tested with 2p10GE NIC X553 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 254 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-2n-ethip4-ip4src254 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs L2 patch config with ${phy_cores} phy +| | ... | core(s). +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 patch +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-eth-l2patch-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-eth-l2patch-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-eth-l2patch-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-eth-l2patch-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-eth-l2patch-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-eth-l2patch-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-eth-l2patch-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-eth-l2patch-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-eth-l2patch-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-eth-l2patch-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-eth-l2patch-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-eth-l2patch-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2patch-ndrpdr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2patch-ndrpdr.robot new file mode 100644 index 0000000000..b149cc0933 --- /dev/null +++ b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2patch-ndrpdr.robot @@ -0,0 +1,131 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X553 | ETH | L2PATCH | BASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L2 | Intel-X553 +| ... +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2patch test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 patch. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 patch\ +| ... | DUT1 tested with 2p10GE NIC X553 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library\ +| ... | Test packets are generated by TG on\ +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ +| ... | (flow-group per direction, 254 flows per flow-group) with\ +| ... | all packets containing Ethernet header,IPv4 header with static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-2n-ethip4-ip4src254 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs L2 patch config with ${phy_cores} phy +| | ... | core(s). +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 patch +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-eth-l2patch-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-eth-l2patch-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-eth-l2patch-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-eth-l2patch-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-eth-l2patch-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-eth-l2patch-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-eth-l2patch-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-eth-l2patch-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-eth-l2patch-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-eth-l2patch-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-eth-l2patch-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-eth-l2patch-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2xcbase-mrr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2xcbase-mrr.robot new file mode 100644 index 0000000000..511b39ee9e --- /dev/null +++ b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2xcbase-mrr.robot @@ -0,0 +1,125 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X553 | ETH | L2XCFWD | BASE | L2XCBASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L2 | Intel-X553 +| ... +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2XC test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect. +| ... | DUT1 tested with 2p10GE NIC X553 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-ethip4-ip4src254 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config.\ +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 2-node circular topology +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-eth-l2xcbase-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-eth-l2xcbase-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-eth-l2xcbase-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-eth-l2xcbase-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-eth-l2xcbase-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-eth-l2xcbase-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-eth-l2xcbase-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-eth-l2xcbase-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-eth-l2xcbase-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-eth-l2xcbase-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-eth-l2xcbase-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-eth-l2xcbase-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2xcbase-ndrpdr.robot b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2xcbase-ndrpdr.robot new file mode 100644 index 0000000000..ae38939a16 --- /dev/null +++ b/tests/vpp/perf/l2/2n1l-10ge2p1x553-eth-l2xcbase-ndrpdr.robot @@ -0,0 +1,131 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X553 | ETH | L2XCFWD | BASE | L2XCBASE +| ... +| Suite Setup | Set up 2-node performance topology with DUT's NIC model +| ... | L2 | Intel-X553 +| ... +| Suite Teardown | Tear down 2-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2XC test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect. +| ... | DUT1 tested with 2p10GE NIC X553 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library\ +| ... | Test packets are generated by TG on\ +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ +| ... | (flow-group per direction, 254 flows per flow-group) with\ +| ... | all packets containing Ethernet header,IPv4 header with static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X553 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-2n-ethip4-ip4src254 + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config.\ +| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 2-node circular topology +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-eth-l2xcbase-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-eth-l2xcbase-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-eth-l2xcbase-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-eth-l2xcbase-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-eth-l2xcbase-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-eth-l2xcbase-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-eth-l2xcbase-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-eth-l2xcbase-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-eth-l2xcbase-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-eth-l2xcbase-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-eth-l2xcbase-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-eth-l2xcbase-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} |